Microstructural evolution during hot deformation of duplex stainless steel

The microstructure evolution during hot deformation of a 23Cr-5Ni-3Mo duplex stainless steel was investigated in torsion. The presence of a soft δ ferrite phase in the vicinity of austenite caused strain partitioning, with accommodation of more strain in the δ ferrite. Furthermore, owing to the limited number of austenite/austenite grain boundaries, the kinetics of dynamic recrystallisation (DRX) in austenite was very slow. The first DRX grains in the austenite phase formed at a strain beyond the peak and proceeded to <15% of the microstructure at the rupture strain of the sample. On the other hand, the microstructure evolution in δ ferrite started by formation of low angle grain boundaries at low strains and the density of these boundaries increased with increasing strain. There was clear evidence of continuous dynamic recrystallisation in this phase at strains beyond the peak. However, in the δ ferrite phase at high strains, most grains consisted of δ/δ and δ/γ boundaries.

Cyclic GMP modulates stomatal opening induced by natriuretic peptides and immunoreactive analogues

In this paper we demonstrate that compounds that promote stomatal opening such as kinetin, atrial natriuretic peptide (ANP) and plant natriuretic peptide immunoanalogues (irPNP) significantly elevate cGMP in guard cell protoplasts. Stomata opened by irPNP are induced to close in the presence of the guanylate cyclase inhibitor, LY 83583. The effect of cGMP on stomatal opening appears to be linked with Ca2+ levels. ANP, irPNP and 8-Br-cGMP all induce stomatal opening and this is inhibited by compounds that lower intracellular Ca2+ levels such as ethylene glycol bis(β-aminoethyl ether) N,N,N’,N’-tetraacetic acid (EGTA), ruthenium red and procaine.

Feasibility study of partial recrystallisation in multi-pass hot deformation process and application to calculation of mean flow stress

A feasibility study for handling the partial recrystallisation in multi-pass hot deformation where the heterogeneity of microstructure of deformed austenite is inherently accompanied is presented. The proposed model is based on modification of the conventional model in which the microstructure of deformed austenite at each pass is simply taken as being homogeneous during the multi-pass deformation. The usefulness of the modified model has been demonstrated by applying it to a four-pass oval–round (or round–oval) rod rolling sequence. The recrystallised fraction, austenite grain size (AGS) and mean flow stress at each pass computed from the modified model has been compared with those from the conventional model. The result showed that the recrystallisation behaviour and evolution of AGS at a given pass were dependent on the modelling method of the partial recrystallisation in the multi-pass rolling for the case studied. As the rolling speed increased, the difference between the mean flow stresses calculated by the conventional model and the proposed model was gradually larger in accordance with the contribution of partial recrystallisation.

Effect of composition and austenite deformation on the transformation characteristics of low-carbon and ultralow-carbon microalloyed steels

Deformation dilatometry has been used to simulate controlled hot rolling followed by controlled cooling of a group of low- and ultralow-carbon microalloyed steels containing additions of boron and/or molybdenum to enhance hardenability. Each alloy was subjected to simulated recrystallization and nonrecrystallization rolling schedules, followed by controlled cooling at rates from 0.1 °C/s to about 100 °C/s, and the corresponding continuous-cooling-transformation (CCT) diagrams were constructed. The resultant microstructures ranged from polygonal ferrite (PF) for combinations of slow cooling rates and low alloying element contents, through to bainitic ferrite accompanied by martensite for fast cooling rates and high concentrations of alloying elements. Combined additions of boron and molybdenum were found to be most effective in increasing steel hardenability, while boron was significantly more effective than molybdenum as a single addition, especially at the ultralow carbon content. Severe plastic deformation of the parent austenite (>0.45) markedly enhanced PF formation in those steels in which this microstructural constituent was formed, indicating a significant effective decrease in their hardenability. In contrast, in those steels in which only nonequilibrium ferrite microstructures were formed, the decreases in hardenability were relatively small, reflecting the lack of sensitivity to strain in the austenite of those microstructural constituents forming in the absence of PF.

Compressive deformation behaviour of a closed-cell aluminum

The mechanical properties of a closed-cell aluminium foam were investigated by compressive tests, and the deformation behaviours of the aluminium foams were studied using Xray microtomography. The results indicate that the deformation of the aluminium foams under compressive loading was localized in narrow continuous deformation bands having widths of order of a cell diameter. The cells in the deformation bands collapsed by a mixed deformation mechanism, which includes mainly bending and minor buckling and yielding. Different fractions of the three deformation modes led to variations in the peak stress and energy absorption for different foam samples with the same density. It was also found that the cell morphology affects the deformation mechanism significantly, whilst the cell size shows little influence.