Verification of design calculations of a wind catcher/tower natural ventilation system with performance testing in real building

A wind catcher/tower natural ventilation system was installed in a seminar room in the building of the School of Construction Management and Engineering, the University of Reading in the UK . Performance was analysed by means of ventilation tracer gas measurements, indoor climate measurements (temperature, humidity, CO2) and occupant surveys. In addition, the potential of simple design tools was evaluated by comparing observed ventilation results with those predicted by an explicit ventilation model and the AIDA implicit ventilation model. To support this analysis, external climate parameters (wind speed and direction, solar radiation, external temperature and humidity) were also monitored. The results showed the chosen ventilation design provided a substantially greater ventilation rate than an equivalent area of openable window. Also air quality parameters stayed within accepted norms while occupants expressed general satisfaction with the system and with comfort conditions. Night cooling was maximised by using the system in combination with openable windows. Comparisons of calculations with ventilation rate measurements showed that while AIDA gave reasonably correlated results with the monitored performance results, the widely used industry explicit model was found to over estimate the monitored ventilation rate.

Dynamic modelling of a wind catcher/tower turret for natural ventilation

This paper discusses experimental and theoretical investigations and Computational Fluid Dynamics (CFD) modelling considerations to evaluate the performance of a square section wind catcher system connected to the top of a test room for the purpose of natural ventilation. The magnitude and distribution of pressure coefficients (C-p) around a wind catcher and the air flow into the test room were analysed. The modelling results indicated that air was supplied into the test room through the wind catcher's quadrants with positive external pressure coefficients and extracted out of the test room through quadrants with negative pressure coefficients. The air flow achieved through the wind catcher depends on the speed and direction of the wind. The results obtained using the explicit and AIDA implicit calculation procedures and CFX code correlate relatively well with the experimental results at lower wind speeds and with wind incidents at an angle of 0 degrees. Variation in the C-p and air flow results were observed particularly with a wind direction of 45 degrees. The explicit and implicit calculation procedures were found to be quick and easy to use in obtaining results whereas the wind tunnel tests were more expensive in terms of effort, cost and time. CFD codes are developing rapidly and are widely available especially with the decreasing prices of computer hardware. However, results obtained using CFD codes must be considered with care, particularly in the absence of empirical data.

Quantitative pulsed phase thermography applied to steel plates

Pulsed Phase Thermography (PPT) has been proven effective on depth retrieval of flat-bottomed holes in different materials such as plastics and aluminum. In PPT, amplitude and phase delay signatures are available following data acquisition (carried out in a similar way as in classical Pulsed Thermography), by applying a transformation algorithm such as the Fourier Transform (FT) on thermal profiles. The authors have recently presented an extended review on PPT theory, including a new inversion technique for depth retrieval by correlating the depth with the blind frequency fb (frequency at which a defect produce enough phase contrast to be detected). An automatic defect depth retrieval algorithm had also been proposed, evidencing PPT capabilities as a practical inversion technique. In addition, the use of normalized parameters to account for defect size variation as well as depth retrieval from complex shape composites (GFRP and CFRP) are currently under investigation. In this paper, steel plates containing flat-bottomed holes at different depths (from 1 to 4.5 mm) are tested by quantitative PPT. Least squares regression results show excellent agreement between depth and the inverse square root blind frequency, which can be used for depth inversion. Experimental results on steel plates with simulated corrosion are presented as well. It is worth noting that results are improved by performing PPT on reconstructed (synthetic) rather than on raw thermal data.

Out of the ivory tower: the impact of wider social contact on the values, religious beliefs and identities of Chinese postgraduate students in the UK

This article explores the impact of wider social contact on the experience of Chinese postgraduate students of adaptation to life in the UK. Focus group and individual interviews were conducted with a group of 11 Chinese students on an MA programme at a university in southern England and individual interviews with three representatives of a local volunteer group (LVG) offering support to the Chinese students. Although it was perceived that the students’ support needs were not adequately met by the University, the additional support offered outside the University was unanimously valued and considered as enriching their cultural and linguistic experiences and meeting their expectations. However, frequent social contact with the LVG, whose members were mostly Christians, also had an impact on their values, religious beliefs and identities. In a discussion framed within the sociological perspective of proselytization or religious conversion and the broad framework of international education and globalization, the different responses to this contact are described in terms of believers, doubters, empathisers and commentators. Implications are considered for universities, people involved in providing social support for international students, and sponsors of international students.

A wind-tunnel study of flow distortion at a meteorological sensor on top of the BT Tower, London, UK

High quality wind measurements in cities are needed for numerous applications including wind engineering. Such data-sets are rare and measurement platforms may not be optimal for meteorological observations. Two years' wind data were collected on the BT Tower, London, UK, showing an upward deflection on average for all wind directions. Wind tunnel simulations were performed to investigate flow distortion around two scale models of the Tower. Using a 1:160 scale model it was shown that the Tower causes a small deflection (ca. 0.5°) compared to the lattice on top on which the instruments were placed (ca. 0–4°). These deflections may have been underestimated due to wind tunnel blockage. Using a 1:40 model, the observed flow pattern was consistent with streamwise vortex pairs shed from the upstream lattice edge. Correction factors were derived for different wind directions and reduced deflection in the full-scale data-set by <3°. Instrumental tilt caused a sinusoidal variation in deflection of ca. 2°. The residual deflection (ca. 3°) was attributed to the Tower itself. Correction of the wind-speeds was small (average 1%) therefore it was deduced that flow distortion does not significantly affect the measured wind-speeds and the wind climate statistics are reliable.

To what extent are EU steel companies susceptible to competitive loss due to climate policy?

In recognition of their competitive vulnerability, a set of special rules have been devised for managing sectors such as steel and cement within the EU ETS. These rules basically seek to set sector specific performance benchmarks and reward top performers. However, the steel sector as a whole will receive the vast majority of its allowances for free in Phase III. Perceptions of competitive vulnerability have been largely based on inherently hypothetical analyses which rely heavily on counterfactual scenario and abatement cost estimates often provided by firms themselves. This paper diverges from these approaches by providing a qualitative assessment of the two key reasons underpinning the competitive vulnerability argument of the EU Steel Companies based on interviews and case study involving the three largest producers of steel within the EU – AcerlorMittal, Corus, and ThyssenKrupp. We find that these arguments provide only partial and weak justifications for competitive loss and discriminatory treatment in the EUETS. This strategy is difficult to counter by governments due to information asymmetry; and it appears to have proved very successful insofar as it has helped the industry to achieve free allocation in Phases I-III of EU ETS by playing up the risk of carbon leakage.

Simulated and observed fluxes of sensible and latent heat and CO2 at the WLEF-TV tower using SiB2.5

Three years of meteorological data collected at the WLEF-TV tower were used to drive a revised version of the Simple Biosphere (SiB 2.5) Model. Physiological properties and vegetation phenology were specified from satellite imagery. Simulated fluxes of heat, moisture, and carbon were compared to eddy covariance measurements taken onsite as a means of evaluating model performance on diurnal, synoptic, seasonal, and interannual time scales. The model was very successful in simulating variations of latent heat flux when compared to observations, slightly less so in the simulation of sensible heat flux. The model overestimated peak values of sensible heat flux on both monthly and diurnal scales. There was evidence that the differences between observed and simulated fluxes might be linked to wetlands near the WLEF tower, which were not present in the SiB simulation. The model overestimated the magnitude of the net ecosystem exchange of CO2 in both summer and winter. Mid-day maximum assimilation was well represented by the model, but late afternoon simulations showed excessive carbon uptake due to misrepresentation of within-canopy shading in the model. Interannual variability was not well simulated because only a single year of satellite imagery was used to parameterize the model.