A Continuous Span Aluminum Girder Concrete Deck Bridge - Part 2 of 2: Fatigue Tests of Aluminum Girders, Final Report, 1997

In 1957, the Iowa State Highway Commission, with financial assistance from the aluminum industry, constructed a 220-ft (67-m) long, four-span continuous, aluminum girder bridge to carry traffic on Clive Road (86th Street) over Interstate 80 near Des Moines, Iowa. The bridge had four, welded I-shape girders that were fabricated in pairs with welded diaphragms between an exterior and an interior girder. The interior diaphragms between the girder pairs were bolted to girder brackets. A composite, reinforced concrete deck served as the roadway surface. The bridge, which had performed successfully for about 35 years of service, was removed in the fall of 1993 to make way for an interchange at the same location. Prior to the bridge demolition, load tests were conducted to monitor girder and diaphragm bending strains and deflections in the northern end span. Fatigue testing of the aluminum girders that were removed from the end spans were conducted by applying constant-amplitude, cyclic loads. These tests established the fatigue strength of an existing, welded, flange-splice detail and added, welded, flange-cover plates and horizontal web plate attachment details. This part, Part 2, of the final report focuses on the fatigue tests of the aluminum girder sections that were removed from the bridge and on the analysis of the experimental data to establish the fatigue strength of full-size specimens. Seventeen fatigue fractures that were classified as Category E weld details developed in the seven girder test specimens. Linear regression analyses of the fatigue test results established both nominal and experimental stress-range versus load cycle relationships (SN curves) for the fatigue strength of fillet-welded connections. The nominal strength SN curve obtained by this research essentially matched the SN curve for Category E aluminum weldments given in the AASHTO LRFD specifications. All of the Category E fatigue fractures that developed in the girder test specimens satisfied the allowable SN relationship specified by the fatigue provisions of the Aluminum Association. The lower-bound strength line that was set at two standard deviations below the least squares regression line through the fatigue fracture data points related well with the Aluminum Association SN curve. The results from the experimental tests of this research have provided additional information regarding behavioral characteristics of full-size, aluminum members and have confirmed that aluminum has the strength properties needed for highway bridge girders.

Fluorescence flow cytometer to determine urine particle reference intervals in doping control samples.

Background: Urine is still the matrix of choice to fight against doping, because it can be collected non-invasively during anti-doping tests. Most of the World Anti-Doping Agency's accredited laboratories have more than 20 years experience in analyzing this biological fluid and the majority of the compounds listed in the 2010 Prohibited List - International Standard are eliminated through the urinary apparatus. Storing and transporting urine samples for doping analyses does not include a specific protocol to prevent microbial and thermal degradation. The use of a rapid and reliable screening method could enable determine reference intervals for urine specimens in doping control samples and evaluate notably the prevalence of microbial contamination known to be responsible for the degradation of chemical substances in urine.Methods: The Sysmex(R) UF-500i is a recent urine flow cytometer analyzer capable of quantifying BACT and other urinary particles such as RBC, WBC, EC, DEBRIS, CAST, PATH. CAST, YLC, SRC as well as measuring urine conductivity. To determine urine anti-doping reference intervals, 501 samples received in our laboratory over a period of two months were submitted to an immediate examination. All samples were collected and then transported at room temperature. Analysis of variance was performed to test the effects of factors such as gender, test type [in-competition, out-of-competition] and delivery time.Results: The data obtained showed that most of the urine samples were highly contaminated with bacteria. The other urine particles were also very different according to the factors.Conclusions: The Sysmex(R) UF-500i was capable of providing a snapshot of urine particles present in the samples at the time of the delivery to the laboratory. These particles, BACT in particular, gave a good idea of the possible microbial degradation which had and/or could have occurred in the sample. This information could be used as the first quality control set up in WADA (World Anti-Doping Agency) accredited laboratories to determine if steroid profiles, endogenous and prohibited substances have possibly been altered. (C) 2011 Elsevier Ireland Ltd. All rights reserved.

Feeding rate and frequency on juvenile pompano growth

The objective of this work was to evaluate the ideal feeding rate and frequency for juvenile pompano (Trachinotus marginatus). Two experiments were carried out in a completely randomized design, with three replicates each. In experiment I, 25 fish (4.8±0.6 g and 6.48±0.01 cm) were stocked in 15 tanks (50 L) during 21 days and fed 4, 8, 12, 16, and 20% body weight per day. In experiment II, 20 fish (4.1±0.1 g and 6.6±0.1 cm) were stocked in 15 tanks (40 L) during 28 days and fed 2, 6, 8, and 10 times a day. The tested feeding rates and frequencies did not influence survival. Final weight and length in experiment I were significantly lower in fish fed 4% body weight per day, whereas in experiment II only weight was significantly lower in fish fed 2 and 6 times a day. At the end of both experiments, apparent feed conversion showed significant difference, with the worst value observed for fish fed 20% body weight per day in experiment I and 2 times a day in experiment II. Juvenile pompano show better growth performance when fed 8% body weight per day and 8 times a day.

Feeding strategies and energy to protein ratio on tambaqui performance and physiology

The objective of this work was to evaluate the effect of feed deprivation and refeeding with diets containing different energy to protein ratios (E/P) on the performance and physiology of juvenile tambaqui (Colossoma macropomum). A 4x2 factorial arrangement with three replicates was used, with four E/P ratios (11.5, 10.5, 9.5, and 8.5 kcal g-1 digestible energy per protein) and two feeding regimens (with and without deprivation), during 60 days. Fish from the food-deprived group were fasted for 14 days and refed from the fifteenth to the sixtieth day, whereas the remaining fish were fed for 60 days. At the end of the experimental period, weight of fish subjected to food deprivation was lower than that of those continuously fed; however, this condition did not influence the physiological parameters analyzed. Tambaqui fed 11.5 kcal g-1 achieved lower final weight than those fed with the other diets, in both regimens. Among the physiological parameters, only plasma protein presented significant increase in fish fed 8.5 kcal g-1, in both feeding regimens, probably due to the higher dietary protein concentration. These results indicate that fish show a partial compensatory growth, and that 10.5 kcal g-1 can be recommended for the diet of juvenile tambaqui.

Stocking densities and feeding strategies in shrimp and tilapia polyculture in tanks

The objective of this work was to evaluate the performance of Pacific marine shrimp (Litopenaeus vannamei) and tilapia (Oreochromis niloticus), in a polyculture in tanks subjected to different stocking densities and feeding strategies, in comparison with monoculture. Two experiments were performed, at the same time, in a completely randomized design with three treatments and four replicates each. Treatments for experiment I were: monoculture with 10 shrimp per m² (10S:0T); polyculture with 10 shrimp and 0.5 tilapia per m² (10S:0.5T); and polyculture with 10 shrimp and 1 tilapia per m² (10S:1T). Shrimp was the main crop, and feed was provided based on shrimp biomass. Treatments for experiment II were: monoculture with 2 tilapia per m² (2T:0S); polyculture with 2 tilapia and 2.5 shrimp per m² (2T:2.5S); and polyculture with 2 tilapia and 5 shrimp per m² (2T:5S). Tilapia was the main crop, and feed was provided based on fish requirements. In the experiment I, tilapia introduction to shrimp culture resulted in lower shrimp growth and poor feed conversion rate. In experiment II, shrimp introduction to tilapia culture did not interfere with fish performance. Polyculture is more efficient with the combination of 2 tilapia and 2.5 or 5 shrimp per m² and feed based on fish requirements.

Alternative tests for correct specification of conditional predictive densities

We propose new methods for evaluating predictive densities that focus on the models' actual predictive ability in finite samples. The tests offer a simple way of evaluatingthe correct specification of predictive densities, either parametric or non-parametric.The results indicate that our tests are well sized and have good power in detecting mis-specification in predictive densities. An empirical application to the Survey ofProfessional Forecasters and a baseline Dynamic Stochastic General Equilibrium modelshows the usefulness of our methodology.

Testing of Vacuum Drum Filter

Tämän diplomityön tavoitteena oli testata ja optimoida erään alipainerumpusuodattimen toimivuutta, ja lisäksi maksimoida tuottavuus ja vertailla erilaisten pesumenetelmientehokkuutta. Testilietteiden ¿ rautarikasteen ja täyteainepastan ¿ karakterisointi oli myös tärkeää. Kirjallisuusosassa tarkasteltiin lyhyesti neste-kiintoaine-erotuksen teoriaa, erityisesti alipainesuodatusta ja alipainerumpusuodattimia. Lisäksi käsiteltiin kapillaarisuodatuksen toimintaperiaatteita sekä selvitettiin kaivosteollisuuden veden talteenottokeinoja, kiintoainejäämien käsittelymenetelmiä ja Chilen kaivosteollisuuden nykytilaa. Työn kokeellinen osa suoritettiin käyttämällä raskaita ja kiintoainepitoisuuksiltaan korkeita lietteitä, eli rautarikastetta ja täyteainepastaa. Kokeet suoritettiin erityisellä alipainerumpusuodattimella, joka oli muokattu perinteisestäpäältä syötettävästä alipainerumpusuodattimesta. Kokeissa tutkittiin pyörimisnopeuden ja erilaisten pesumenetelmien vaikutusta kakun kosteuteen ja suodatuskapasiteettiin. Koelietteiden karakterisointi suoritettiin analysoimalla partikkelikokojakauma, kiintoainepitoisuus, metallipitoisuus ja koostumus. Kokeiden perusteella havaittiin, että rummun pyörimisnopeudella ja lietteen kiintoainepitoisuudella on merkittävä vaikutus suodatuskapasiteettiin ja kakun kosteuspitoisuuteen. Havaittiin myös, että kakun kosteuspitoisuuksissa ja rummun suodatuskapasiteeteissa oli eroja, kun verrattiin eri suodatinväliaineen pesumenetelmiä. Täten oikean pesumenetelmän valinta on tärkeää, ja sillä pystytään lisäämään suodatinväliaineen käyttöikää.

Simultaneous measurement of regional cerebral blood flow by perfusion CT and stable xenon CT: a validation study.

BACKGROUND AND PURPOSE: Knowledge of cerebral blood flow (CBF) alterations in cases of acute stroke could be valuable in the early management of these cases. Among imaging techniques affording evaluation of cerebral perfusion, perfusion CT studies involve sequential acquisition of cerebral CT sections obtained in an axial mode during the IV administration of iodinated contrast material. They are thus very easy to perform in emergency settings. Perfusion CT values of CBF have proved to be accurate in animals, and perfusion CT affords plausible values in humans. The purpose of this study was to validate perfusion CT studies of CBF by comparison with the results provided by stable xenon CT, which have been reported to be accurate, and to evaluate acquisition and processing modalities of CT data, notably the possible deconvolution methods and the selection of the reference artery. METHODS: Twelve stable xenon CT and perfusion CT cerebral examinations were performed within an interval of a few minutes in patients with various cerebrovascular diseases. CBF maps were obtained from perfusion CT data by deconvolution using singular value decomposition and least mean square methods. The CBF were compared with the stable xenon CT results in multiple regions of interest through linear regression analysis and bilateral t tests for matched variables. RESULTS: Linear regression analysis showed good correlation between perfusion CT and stable xenon CT CBF values (singular value decomposition method: R(2) = 0.79, slope = 0.87; least mean square method: R(2) = 0.67, slope = 0.83). Bilateral t tests for matched variables did not identify a significant difference between the two imaging methods (P >.1). Both deconvolution methods were equivalent (P >.1). The choice of the reference artery is a major concern and has a strong influence on the final perfusion CT CBF map. CONCLUSION: Perfusion CT studies of CBF achieved with adequate acquisition parameters and processing lead to accurate and reliable results.

Nauhasuodatukseen vaikuttavien parametrien tutkiminen

Nauhasuodattimia käytetään teollisuuden aloilla, joissa suodatettavan suspension määrä vaihtelee laajalti ja suodinkakun peseytyminen on tärkeää. Oikean kangasrakenteen valinnalla voidaan kasvattaa suodatuskapasiteettia ja parantaa suodatustulosta. Tämän diplomityön tavoitteena oli tutkia metallisulfidisakan nauhasuodatukseen liittyviä parametreja suodatuksen parantamiseksi. Tavoitteena oli löytää sopiva kangas ja ajoparametrit kloridin pesemiseksi suodinkakusta mahdollisimman tarkasti ja samalla säilyttää hyvä suodospuhtaus. Suodatuskapasiteetin kasvattaminen oli myös toivottavaa. Kirjallisuusosassa keskityttiin kakkusuodatuksen teoriaan, nauhasuodatukseen ja tutustuttiin hieman nauhasuodatukseen liittyvään laskentaan. Uusia kehitteillä olevia suodatusta parantavia menetelmiä käsiteltiin myös kirjallisuusosassa. Kokeellisessa osassa tutkittiin koesuunnittelua hyväksi käyttäen metallisulfidisakan suodatukseen vaikuttavienparametrien vaikutusta. Testattavia parametreja olivat mm. alipaine, lietteen kiintoainepitoisuus, syötön ja pesuveden määrä. Kokeet osoittivat, että kankaan rakenteella ei ole suurta vaikutusta pesutulokseen. Pesuilla ei myöskään voida kokonaan poistaa suodinkakussa olevaa kloridia. Tulosten perusteella kokeissa käytetyillä kudotuilla kankailla päästiin yhtä hyviin kuin huopakankaalla. Suodattimen toiminnan kannalta paras tilanne on, jos suodattimelle tulevan lietteen kiintoainepitoisuus pysyy melko vakiona. Suodattimella käytettävän kankaan käyttöikää kasvattaa kankaan hyvä kulutuskestävyys, kakun irtoaminen helposti kankaan pinnalta ja kankaan pysyminen huokoisena kankaan pesujen ansiosta.

Weak Form Tests of Efficient Market Hypothesis: Evidence from CEE-Countries and Russian Stock Markets

Tämän tutkielman tavoitteena on selvittää Venäjän, Slovakian, Tsekin, Romanian, Bulgarian, Unkarin ja Puolan osakemarkkinoiden heikkojen ehtojen tehokkuutta. Tämä tutkielma on kvantitatiivinen tutkimus ja päiväkohtaiset indeksin sulkemisarvot kerättiin Datastreamin tietokannasta. Data kerättiin pörssien ensimmäisestä kaupankäyntipäivästä aina vuoden 2006 elokuun loppuun saakka. Analysoinnin tehostamiseksi dataa tutkittiin koko aineistolla, sekä kahdella aliperiodilla. Osakemarkkinoiden tehokkuutta on testattu neljällä tilastollisella metodilla, mukaan lukien autokorrelaatiotesti ja epäparametrinen runs-testi. Tavoitteena on myös selvittääesiintyykö kyseisillä markkinoilla viikonpäiväanomalia. Viikonpäiväanomalian esiintymistä tutkitaan käyttämällä pienimmän neliösumman menetelmää (OLS). Viikonpäiväanomalia on löydettävissä kaikilta edellä mainituilta osakemarkkinoilta paitsi Tsekin markkinoilta. Merkittävää, positiivista tai negatiivista autokorrelaatiota, on löydettävissä kaikilta osakemarkkinoilta, myös Ljung-Box testi osoittaa kaikkien markkinoiden tehottomuutta täydellä periodilla. Osakemarkkinoiden satunnaiskulku hylätään runs-testin perusteella kaikilta muilta paitsi Slovakian osakemarkkinoilla, ainakin tarkastellessa koko aineistoa tai ensimmäistä aliperiodia. Aineisto ei myöskään ole normaalijakautunut minkään indeksin tai aikajakson kohdalla. Nämä havainnot osoittavat, että kyseessä olevat markkinat eivät ole heikkojen ehtojen mukaan tehokkaita