Effect of copper addition on the fracture and fatigue crack growth behavior of solution heat-treated SUS 304H austenitic steel

Small additions of Cu to the SUS 304H, a high temperature austenitic stainless steel, enhance its high temperature strength and creep resistance. As Cu is known to cause embrittlement, the effect of Cu on room temperature mechanical properties that include fracture toughness and fatigue crack threshold of as-solutionized SUS 304H steel were investigated in this work. Experimental results show a linear reduction in yield and ultimate strengths with Cu addition of up to 5 wt.% while ductility drops markedly for 5 wt.% Cu alloy. However, the fracture toughness and the threshold stress intensity factor range for fatigue crack initiation were found to be nearly invariant with Cu addition. This is because the fracture in this alloy is controlled by the debonding from the matrix of chromium carbide precipitates, as evident from fractography. Cu, on the other hand, remains either in solution or as nano-precipitates and hence does not influence the fracture characteristics. It is concluded that small additions of Cu to 304H will not have adverse effects on its fracture and fatigue behavior. (C) 2010 Elsevier B.V. All rights reserved.

A new ELISA plate based microtiter well assay for mycobacterial topoisomerase I for the direct screening of enzyme inhibitory monoclonal antibody supernatants

Antigen specific monoclonal antibodies present in crude hybridoma supernatants are normally screened by ELISA on plates coated with the relevant antigen. Screening for inhibitory monoclonals to enzymes would require the evaluation of purified antibodies or antibody containing supernatants for their inhibition of enzyme activity in a separate assay. However, screening for inhibitory antibodies against DNA transacting enzymes such as topoisomerase I (topo I) cannot be done using hybridoma supernatants due to the presence of nucleases in tissue culture media containing foetal calf serum which degrade the DNA substrates upon addition. We have developed a simple and rapid screening procedure for the identification of clones that secrete inhibitory antibodies against mycobacterial topo I using 96 well ELISA microtiter plates. The principle of the method is the selective capture of monoclonal antibodies from crude hybridoma supernatants by topo I that is tethered to the plate through the use of plate-bound polyclonal anti-topo I antibodies. This step allows the nucleases present in the medium to be washed off leaving the inhibitor bound to the tethered enzyme. The inhibitory activity of the captured antibody is assessed by performing an in situ DNA relaxation assay by the addition of supercoiled DNA substrate directly to the microtiter well followed by the analysis of the reaction products by agarose gel electrophoresis. The validity of this method was confirmed by purification of the identified inhibitory antibody and its evaluation in a DNA relaxation assay. Elimination of all enzyme-inhibitory constituents of the culture medium from the well in which the inhibitory antibody is bound to the tethered enzyme may make this method broadly applicable to enzymes such as DNA gyrases, restriction enzymes and other DNA transaction enzymes. Further, the method is simple and avoids the need of prior antibody purification for testing its inhibitory activity. (C) 2010 Elsevier B.V. All rights reserved.

Shareholder/Stakeholder Value Management, Company Growth and

There has been considerable discussion in the literature about the relative merits of shareholder value management and stakeholder value management, but relatively little empirical research has been reported concerning the relationship between these types of management and financial performance. The present study puts forward a hypothesis that true shareholder value management also encompasses stakeholder value management. This combination of shareholder/stakeholder value management is hypothesised to be associated with superior financial performance and sales growth. Using a sample of chief financial officers' ratings of the contemporary management accounting techniques economic value added and the balanced scorecard to represent the two management types, the study found evidence in support of the hypothesis.

Crystal growth, transport and magnetic properties of rare-earth manganite Pr1-xPbxMnO3

Crystal growth, electrical and magnetic properties are reported for mixed valence manganite Pr1-xPbxMnO3 (x = 0.2, 0.23, and 0.3). The crystals with x = 0.2 and 0.23 are ferromagnetic and insulating, whereas that with x = 0.3 is ferromagnetic below 200 K and shows an insulator-metal transition at 235 K. This composition shows a magnetoresistance of 90% in a field of 5 T. In the paramagnetic region, the temperature dependence of magnetic susceptibility of the crystals follows a Curie-Weiss behavior. The thermal evolution of magnetization in the ferromagnetic phase varies as T-3/2, in accordance with Bloch's law. The spin-stiffness constant D obtained from the Bloch constant is found to increase linearly with x. The magnetization does not reach complete saturation upto a field of 5 T. A possible contribution of the Pr spins to the total magnetic moment is discussed.

Epitaxial growth of Co3O4 films by low temperature, low pressure chemical vapour deposition

The growth of strongly oriented or epitaxial thin films of metal oxides generally requires relatively high growth temperatures or infusion of energy to the growth surface through means such as ion bombardment. We have grown high quality epitaxial thin films of Co3O4 on different substrates at a temperature as low as 400 degreesC by low-pressure metalorganic chemical vapour deposition (MOCVD) using cobalt(II) acetylacetonate as the precursor. With oxygen as the reactant gas, polycrystalline Co3O4 films are formed on glass and Si (100) in the temperature range 400-550 degreesC. Under similar conditions of growth. highly oriented films of Co3O4 are formed on SrTiO3 (100) and LaAlO3 (100). The activation energy for the growth of polycrystalline films on glass is significantly higher than that for epitaxial growth on SrTiO3 (100). The film on LaAlO3 (100) grown at 450 degreesC shows a rocking curve FWHM of 1.61 degrees, which reduces to 1.32 degrees when it is annealed in oxygen at 725 degreesC. The film on SrTiO3 (100) has a FWHM of 0.33 degrees (as deposited) and 0.29 (after annealing at 725 degreesC). The phi -scan analysis shows cube-on-cube epitaxy on both these substrates. The quality of epitaxy on SrTiO3 (100) is comparable to the best of the perovskite-based oxide thin films grown at significantly higher temperatures. A plausible mechanism is proposed for the observed low temperature epitaxy. (C) 2001 Published by Elsevier Science B.V.

A finite element analysis of quasistatic crack growth in a pressure sensitive constrained ductile layer

Polymeric adhesive layers are employed for bonding two components in a wide variety of technological applications, It has been observed that, unlike in metals, the yield behavior of polymers is affected by the state of hydrostatic stress. In this work, the effect of pressure sensitivity of yielding and layer thickness on quasistatic interfacial crack growth in a ductile adhesive layer is investigated. To this end, finite deformation, finite element analyses of a cracked sandwiched layer are carried out under plane strain, small-scale yielding conditions for a wide range of mode mixities. The Drucker-Prager constitutive equations are employed to represent the behavior of the layer. Crack propagation is simulated through a cohesive zone model, in which the interface is assumed to follow a prescribed traction-separation law. The results show that for a given mode mixity, the steady state Fracture toughness [K](ss) is enhanced as the degree of pressure sensitivity increases. Further, for a given level of pressure sensitivity, [K](ss) increases steeply as mode Il loading is approached. (C) 2000 Elsevier Science Ltd. All rights reserved.

Growth and characterization of germanium nanowires by electron beam evaporation

Germanium nanowires were grown on Au coated Si substrates at 380 degrees C in a high vacuum (5 x 10(-5) Torr) by e-beam evaporation of Germanium (Ge). The morphology observation by a field emission scanning electron microscope (FESEM) shows that the grown nanowires are randomly oriented with an average length and diameter of 600 nm and 120 nm respectively for a deposition time of 60 min. The nanowire growth ratewas measured to be similar to 10 nm/min. Transmission electron microscope (TEM) studies revealed that the Ge nanowires were single crystalline in nature and further energy dispersive X-ray analysis(EDAX) has shown that the tip of the grown nanowires was capped with Au nanoparticles, this shows that the growth of the Ge nanowires occurs by the vapour liquid solid (VLS) mechanism. HRTEM studies on the grown Ge nanowire show that they are single crystalline in nature and the growth direction was identified to be along [110]. (C) 2010 Elsevier B.V. All rights reserved.

Growth of and trehalase activity in the thermophilic fungusThermomyces lanuginosus

The thermophilic fungus,Thermomyces lanuginosus, was grown in a glucose-asparagine liquid medium. Optimal mycelial growth occurred at 50°C. The conditions for sporulation were different from those required for vegetative growth. the former being favoured by lower nitrogen level and temperature. Trehalase (α, α-glu coside-l-glucohydrolase, EC 3.2.1.28) was one of the most active glycosidases at 50°C. Non-sporulating mycelium had higher levels of this enzyme than the sporulating mycelium. Trehalase was synthesized constitutively and its activity appears to be controlled by catabolite repression.

The link between foreign aid, public investment and economic growth

Länsimaat ovat rahoittaneet kehitysyhteistyöhankkeita jo lähes kuuden vuosikymmenen ajan, mutta kehitysavun tehokkuudesta ei olla edelleenkään päästy yksimielisyyteen. Yksi avunantajamaiden tapa vaikuttaa kehitysavun tehokkuuteen, eli avun vaikutukseen vastaanottajamaan taloudellisen kasvun kiihdyttäjänä, on sitoa ne julkisen sektorin infrastruktuurihankkeisiin. Joissain tapauksissa tämä vaikuttaa avun vastaanottajan käytökseen ja asenteisiin kehitysapua kohtaan. Tutkielmassa käsitellään kehitysavun tehokkuutta tilanteessa, jossa se on sidottu julkisen sektorin investointeihin kehitysmaassa. Tutkimus pohjaa Kalaitzidakisin ja Kalyvitisin (2008) malliin, jossa osa kehitysmaan julkisen talouden investoinneista rahoitetaan kehitysavulla. Seuraavaksi tarkastellaan ylijäämää tavoittelevan käyttäytymisen (rent- seeking) vaikutusta kehitysavun tehokkuuteen pohjaten Economidesin, Kalyvitisin ja Philippopoulosin (2008) malliin. Tutkielmassa referoidaan lisäksi tutkimuskysymystä sivuavia empiirisiä tutkimuksia, esitellään aluksi tavallisimmat kehitysyhteistyön muodot, sekä esitellään talousteoreettisia näkökulmia kehitysyhteistyön tehokkuuden määrittelylle. Tutkielma perustuu puhtaasti teoreettisiin malleihin ja niissä sovelletut menetelmät ovat matemaattisia. Tutkielmassa käsitellään ensin tapaus, jossa kehitysyhteistyöllä rahoitetaan julkisen sektorin investointihankkeita. Jossain tapauksissa kehitysavun kasvu lasku siirtää vastaanottajamaan kulutusta julkisista investoinneista kulutukseen, jolloin kehitysyhteistyövaroin osittain rahoitettujen hankkeiden koko pienenee, ja suhteellinen tehokkuus laskee. Seuraavaksi tarkastellaan tilannetta, jossa kehitysyhteistyövaroista vain osa päätyy hankkeen rahoittamiseen, ja todetaan, että kehitysavun tehokkuus ja vaikutus maan kansantulon kasvuun vähenee talouden toimijoiden ylijäämää tavoittelevan käyttäytymisen (mukaan lukien korruptio) myötä entisestään. Tämän tutkimuksen perusteella voidaan todeta, että kehitysapu vaikuttaa kehittyvän maan talouden kasvuun tapauksessa, jossa julkisia infrastruktuurihankkeita rahoitetaan osittain maan omin verovaroin ja osittain kehitysyhteistyövaroin. Ylijäämää tavoitteleva käyttäytyminen vaikuttaa kehitysavun tehokkuuteen negatiivistesti vähentäen kehitysavun positiivisia kasvuvaikutuksia.

Changes in the Levels of Free Amino Acids in Various Regions of Cuscuta during Growth

The angiospermous plant parasite Cuscuta derives reduced carbon and nitrogen compounds primarily from its host. Free amino acids along Cuscuta vines in three zones, viz., 0 to 5 cm, 5 to 15 cm, and 15 to 30 cm, which in a broad sense represent the region of cell division, cell elongation and differentiation and vascular tissue differentiation respectively, were quantitatively estimated. The free amino acid content was the highest in the 0 to 5 cm region and progressively decreased along the posterior regions of the vine. The haustorial region showed the lowest content of free amino acids. In general, the free amino acid content in samples collected at 7 p.m. was found to be higher than that in the samples collected at 7 a.m. Three basic amino acids, histidine, the uncommon amino acid γ-hydroxyarginine, and arginine constituted more than 50% of the total free amino acids in all the zones studied except the haustorial region. Aspartic acid and glutamic acid constituted the major portion in the acidic and neutral fraction of amino acids. Glutamine, asparagine, threonine, and serine were eluted together and occurred in substantial amounts. γ-Hydroxyarginine constituted the largest fraction in the cut end exudate of Cuscuta and presumably appeared to be the major form of transport amino acid. γ-Hydroxyarginine was also a major constituent of the basic amino acids in Cuscuta vines parasitizing host plants from widely separated families, suggesting that this amino acid is a biosynthetic product of the parasite rather than that of the hosts. Also, U-14C arginine was converted to γ-hydroxyarginine by cut Cuscuta vines, suggesting that γ-hydroxyarginine is synthesized de novo from arginine by Cuscuta.

The Quest for Well-being in Growth Industries: Contexts, Research Design and Methodological Development

This Working Paper reports the background to the first stage of the ongoing research project, The Quest for Well-being in Growth Industries: A Collaborative Study in Finland and Scotland, conducted under the auspices of the Academy of Finland research programme The Future of Work and Well-being (2008-2011). This collaborative project provides national and transnational data, analysis and outputs. The study is being conducted in the Department of Management and Organisation, Hanken School of Economics, Finland, in collaboration with Glasgow Caledonian University, University of East London, Heriot-Watt University and Reading University, UK. The project examines policies and practices towards the enhancement of work-related well-being in growth industries, and contradictory pressures and tensions posed in this situation. The overall aim is to evaluate the development, implementation and use of work-related well-being policies in four selected growth industries. These sectors – electronics, care, finance and accounting, and tourism – have been selected on the basis of European Union and national forecasts, and demographic and socio-economic trends in employment. In this working paper we outline the background to the research study, the initial research plan, and how the survey of employers has been constructed. The working paper concludes with a brief discussion of general ongoing research issues arising in the project.