Experimental confirmation of FK concentrator insensitivity to chromatic aberrations

The FK concentrator has demonstrated during the last years that compares very well with other Fresnel-based concentrator optics for CPV. There are several features that provide the FK high performance: (1) high optical efficiency; (2) large tolerance to tracking misalignment and manufacturing errors, thanks to a high CAP (Concentration-Acceptance Product); (3) good irradiance uniformity and low chromatic dispersion on the cell surface. Non-uniformities in terms of absolute irradiance and spectral content produced by conventional CPV systems can originate electrical losses in multi-junction (MJ) solar cells. The aim of this work is to analyze the influence of these non-uniformities in the FK concentrator performance and how FK concentrator provides high electrical efficiencies thanks to its insensitivity to chromatic aberrations, especially when components move away from the module nominal position due to manufacturing misalignments. This analysis has been done here by means of both, experimental on-sun measurements and simulations based on 3D fully distributed circuit model for MJ cells.

Outline of Europe-Japan collaborative research on concentrator photovoltaics

The Europe-Japan Collaborative Research Project on Concentrator Photovoltaics (CPV) has been initiated under support by the EC (European Commission) and NEDO (New Energy and Industrial Technology Development Organization) since June 2011. This is project (NGCPV Project; a New Generation of Concentrator PhotoVoltaic cells, modules and systems) is aiming to accelerate the move to very high efficiency and lower cost CPV technologies and to enhance widespread deployment of CPV systems. 7 organizations such as UPM, FhG-ISE Imperial College, BSQ, CEA-INES, ENEA, and PSE in Europe and 9 organizations such as TTI, Univ. Tokyo, AIST, Sharp Co. Daido Steel Co., Kobe Univ., Miyazaki Univ., Asahi Kasei Co., and Takano Co. participate in this project. The targets of this project are 1) to develop world-record efficiency CPV cells of more than 45%, 2) to develop world-record efficiency CPV modules of 35%, 3) to establish standard measurements of CPV cells and modules, 4) to install 50kW CPV system in Spain, to carry out field test of CPV system and to manage power generation of CPV systems, and 5) to develop high-efficiency and low-cost new materials and structure cells such as III-V-N, III-V-on-Si tandem, quantum dots and wells. This paper presents outline of this project and most recent results such as world record efficiency (37.9% under 1-sun) cell and high-efficiency (43.5% under 240-306 suns) concentrator cell with inverted epitaxial grown InGaP/GaAs/InGaAs 3-junction solar cells.

Estudio de las propiedades mecánicas de obleas de silicio

En esta tesis se propone un procedimiento para evaluar la resistencia mecánica de obleas de silicio cristalino y se aplica en diferentes casos válidos para la industria. En el sector de la industria fotovoltaica predomina la tecnología basada en paneles de silicio cristalino. Estos paneles están compuestos por células solares conectadas en serie y estas células se forman a partir de obleas de silicio. Con el objetivo de disminuir el coste del panel, en los últimos años se ha observado una clara tendencia a la reducción del espesor de las obleas. Esta reducción del espesor modifica la rigidez de las obleas por lo que ha sido necesario modificar la manera tradicional de manipularlas con el objetivo de mantener un bajo ratio de rotura. Para ello, es necesario conocer la resistencia mecánica de las obleas. En la primera parte del trabajo se describen las obleas de silicio, desde su proceso de formación hasta sus propiedades mecánicas. Se muestra la influencia de la estructura cristalográfica en la resistencia y en el comportamiento ya que el cristal de silicio es anisótropo. Se propone también el método de caracterización de la resistencia. Se utiliza un criterio probabilista basado en los métodos de dimensionamiento de materiales frágiles en el que la resistencia queda determinada por los parámetros de la ley de Weibull triparamétrica. Se propone el procedimiento para obtener estos parámetros a partir de campañas de ensayos, modelización numérica por elementos finitos y un algoritmo iterativo de ajuste de los resultados. En la segunda parte de la tesis se describen los diferentes tipos de ensayos que se suelen llevar a cabo con este material. Se muestra además, para cada uno de los ensayos descritos, un estudio comparativo de diferentes modelos de elementos finitos simulando los ensayos. Se comparan tanto los resultados aportados por cada modelo como los tiempos de cálculo. Por último, se presentan tres aplicaciones diferentes donde se ha aplicado este procedimiento de estudio. La primera aplicación consiste en la comparación de la resistencia mecánica de obleas de silicio en función del método de crecimiento del lingote. La resistencia de las tradicionales obleas monocristalinas obtenidas por el método Czochralski y obleas multicristalinas es comparada con las novedosas obleas quasi-monocristalinas obtenidas por métodos de fundición. En la segunda aplicación se evalúa la profundidad de las grietas generadas en el proceso de corte del lingote en obleas. Este estudio se realiza de manera indirecta: caracterizando la resistencia de grupos de obleas sometidas a baños químicos de diferente duración. El baño químico reduce el espesor de las obleas eliminando las capas más dañadas. La resistencia de cada grupo es analizada y la comparación permite obtener la profundidad de las grietas generadas en el proceso de corte. Por último, se aplica este procedimiento a un grupo de obleas con características muy especiales: obleas preparadas para formar células de contacto posterior EWT. Estas obleas presentan miles de agujeros que las debilitan considerablemente. Se aplica el procedimiento de estudio propuesto con un grupo de estas obleas y se compara la resistencia obtenida con un grupo de referencia. Además, se propone un método simplificado de estudio basado en la aplicación de una superficie de intensificación de tensiones. ABSTRACT In this thesis, a procedure to evaluate the mechanical strength of crystalline silicon wafers is proposed and applied in different studies. The photovoltaic industry is mainly based on crystalline silicon modules. These modules are composed of solar cells which are based on silicon wafers. Regarding the cost reduction of solar modules, a clear tendency to use thinner wafers has been observed during last years. Since the stiffness varies with thickness, the manipulation techniques need to be modified in order to guarantee a low breakage rate. To this end, the mechanical strength has to be characterized correctly. In the first part of the thesis, silicon wafers are described including the different ways to produce them and the mechanical properties of interest. The influence of the crystallographic structure in the strength and the behaviour (the anisotropy of the silicon crystal) is shown. In addition, a method to characterize the mechanical strength is proposed. This probabilistic procedure is based on methods to characterize brittle materials. The strength is characterized by the values of the three parameters of the Weibull cumulative distribution function (cdf). The proposed method requires carrying out several tests, to simulate them through Finite Element models and an iterative algorithm in order to estimate the parameters of the Weibull cdf. In the second part of the thesis, the different types of test that are usually employed with these samples are described. Moreover, different Finite Element models for the simulation of each test are compared regarding the information supplied by each model and the calculation times. Finally, the method of characterization is applied to three examples of practical applications. The first application consists in the comparison of the mechanical strength of silicon wafers depending on the ingot growth method. The conventional monocrystalline wafers based on the Czochralski method and the multicrystalline ones are compared with the new quasi-monocrystalline substrates. The second application is related to the estimation of the crack length caused by the drilling process. An indirect way is used to this end: several sets of silicon wafers are subjected to chemical etchings of different duration. The etching procedure reduces the thickness of the wafers removing the most damaged layers. The strength of each set is obtained by means of the proposed method and the comparison permits to estimate the crack length. At last, the procedure is applied to determine the strength of wafers used for the design of back-contact cells of type ETW. These samples are drilled in a first step resulting in silicon wafers with thousands of tiny holes. The strength of the drilled wafers is obtained and compared with the one of a standard set without holes. Moreover, a simplified approach based on a stress intensification surface is proposed.

Lifetime improvement after phosphorous diffusion gettering on upgraded metallurgical grade silicon

Wide experimental evidence of the phosphorus diffusion gettering beneficial effect on solar grade silicon is found by measuring electron effective lifetime and interstitial iron concentration in as-grown and post processed samples from two ingots of upgraded metallurgical grade silicon produced by Ferrosolar. Results after two different P-diffusion processes are compared: P emitter diffusion at 850ºC followed by fast cool-down (called “standard process”) or followed by slow cool-down (called “extended process”). It is shown that final lifetimes of this low cost material are in the range of those obtained with conventional material. The extended process can be beneficial for wafers with specific initial distribution and concentration of iron, e.g. materials with high concentration of big Fe precipitates, while for other cases the standard process is enough efficient. An analysis based on the comparison of measured lifetime and dissolved iron concentration with theoretical calculations helps to infer the initial iron distribution and concentration, and according to that, choose the more effective type of gettering.

Experimental and numerical study of cw green laser crystallization of a-Si:H thin films

Crystallization and grain growth technique of thin film silicon are among the most promising methods for improving efficiency and lowering cost of solar cells. A major advantage of laser crystallization and annealing over conventional heating methods is its ability to limit rapid heating and cooling to thin surface layers. Laser energy is used to heat the amorphous silicon thin film, melting it and changing the microstructure to polycrystalline silicon (poly-Si) as it cools. Depending on the laser density, the vaporization temperature can be reached at the center of the irradiated area. In these cases ablation effects are expected and the annealing process becomes ineffective. The heating process in the a-Si thin film is governed by the general heat transfer equation. The two dimensional non-linear heat transfer equation with a moving heat source is solve numerically using the finite element method (FEM), particularly COMSOL Multiphysics. The numerical model help to establish the density and the process speed range needed to assure the melting and crystallization without damage or ablation of the silicon surface. The samples of a-Si obtained by physical vapour deposition were irradiated with a cw-green laser source (Millennia Prime from Newport-Spectra) that delivers up to 15 W of average power. The morphology of the irradiated area was characterized by confocal laser scanning microscopy (Leica DCM3D) and Scanning Electron Microscopy (SEM Hitachi 3000N). The structural properties were studied by micro-Raman spectroscopy (Renishaw, inVia Raman microscope).

New concepts and techniques for the development of high-efficiency concentrating photovoltaic modules

El interés por los sistemas fotovoltaicos de concentración (CPV) ha resurgido en los últimos años amparado por el desarrollo de células multiunión de muy alta eficiencia basadas en semiconductores de los grupos III-V. Estas células han permitido obtener módulos de concentración con eficiencias que prácticamente duplican las del panel plano y que llegan al 35% en los módulos récord. Esta tesis está dedicada al diseño y la implementación experimental de nuevos conceptos que permitan obtener módulos CPV que no sólo alcancen una eficiencia alta en condiciones estándar sino que, además, sean lo suficientemente tolerantes a errores de montaje, seguimiento, temperatura y variaciones espectrales para que la energía que producen a lo largo del año sea máxima. Una de las primeras cuestiones que se abordan es el diseño de elementos ópticos secundarios para sistemas cuyo primario es una lente de Fresnel y que permiten, para una concentración fija, aumentar el ángulo de aceptancia y la tolerancia del sistema. Varios secundarios reflexivos y refractivos han sido diseñados y analizados mediante trazado de rayos. En particular, utilizando óptica anidólica y basándose en el diseño de una sola etapa conocido como ‘concentrador dieléctrico que funciona por reflexión total interna‘, se ha diseñado, fabricado y caracterizado un secundario con salida cuadrada que, usado junto con una lente de Fresnel, permite alcanzar simultáneamente una elevada eficiencia, concentración y aceptancia. Además, se ha propuesto y prototipado un método alternativo de fabricación para otro de los secundarios, denominado domo, consistente en el sobremoldeo de silicona sobre células solares. Una de las características que impregna todo el trabajo realizado en esta tesis es la aproximación holística en el diseño de módulos CPV, es decir, se ha prestado especial atención al diseño conjunto de la célula y la óptica para garantizar que el sistema total alcance la mayor eficiencia posible. En este sentido muchos sistemas ópticos desarrollados en esta tesis han sido diseñados, caracterizados y optimizados teniendo en cuenta que el ajuste de corriente entre las distintas subcélulas que comprenden la célula multiunión bajo el concentrador sea muy próximo a uno. La capa antirreflectante sobre la célula funciona, en cierto modo, como interfaz entre la óptica y la célula, por lo que se ha diseñado un método de optimización de capas antirreflectantes que considera no sólo el amplio rango de longitudes de onda para el que las células multiunión son sensibles sino también la distribución angular de intensidad sobre la célula creada por la óptica de concentración. Además, la cuestión de la falta de uniformidad también se ha abordado mediante la comparación de las distribuciones espectrales y espaciales de irradiancia que crean diferentes ópticas (simuladas mediante trazado de rayos y fotografiadas) y las pérdidas de eficiencia que experimentan las células iluminadas por dichas ópticas de concentración medidas experimentalmente. El efecto de la temperatura en la óptica de concentración también ha sido objeto de estudio de esta tesis. En particular, mediante simulaciones de elementos finitos se han dado los primeros pasos para el análisis de las deformaciones que sufren los dientes de las lentes de Fresnel híbridas (vidrio-silicona), así como el cambio de índice de refracción con la temperatura y la influencia de ambos efectos sobre el funcionamiento de los sistemas. Se ha implementado un modelo que tiene por objeto considerar las variaciones ambientales, principalmente temperatura y contenido espectral de la radiación directa, así como las sensibilidades térmica y espectral de los sistemas CPV, con el fin de maximizar la energía producida por un módulo de concentración a lo largo de un año en un emplazamiento determinado. Los capítulos 5 y 6 de este libro están dedicados al diseño, fabricación y caracterización de un nuevo concepto de módulo fotovoltaico denominado FluidReflex y basado en una única etapa reflexiva con dieléctrico fluido. En este nuevo concepto la presencia del fluido aporta algunas ventajas significativas como son: un aumento del producto concentración por aceptancia (CAP, en sus siglas en inglés) alcanzable al rodear la célula con un medio cuyo índice de refracción es mayor que uno, una mejora de la eficiencia óptica al disminuir las pérdidas por reflexión de Fresnel en varias interfaces, una mejora de la disipación térmica ya que el calor que se concentra junto a la célula se trasmite por convección natural y conducción en el fluido y un aislamiento eléctrico mejorado. Mediante la construcción y medida de varios prototipos de unidad elemental se ha demostrado que no existe ninguna razón fundamental que impida la implementación práctica del concepto teórico alcanzando una elevada eficiencia. Se ha realizado un análisis de fluidos candidatos probando la existencia de al menos dos de ellos que cumplen todos los requisitos (en particular el de estabilidad bajo condiciones de luz concentrada) para formar parte del sistema de concentración FluidReflex. Por ´ultimo, se han diseñado, fabricado y caracterizado varios prototipos preindustriales de módulos FluidReflex para lo cual ha sido necesario optimizar el proceso de fabricación de la óptica multicavidad a fin de mantener el buen comportamiento óptico obtenido en la fabricación de la unidad elemental. Los distintos prototipos han sido medidos, tanto en el laboratorio como bajo el sol real, analizando el ajuste de corriente de la célula iluminada por el concentrador FluidReflex bajo diferentes distribuciones espectrales de la radiación incidente así como el excelente comportamiento térmico del módulo. ABSTRACT A renewed interest in concentrating photovoltaic (CPV) systems has emerged in recent years encouraged by the development of high-efficiency multijunction solar cells based in IIIV semiconductors that have led to CPV module efficiencies which practically double that of flat panel PV and which reach 35% for record modules. This thesis is devoted to the design and experimental implementation of new concepts for obtaining CPV modules that not only achieve high efficiency under standard conditions but also have such a wide tolerance to assembly errors, tracking, temperature and spectral variations, that the energy generated by them throughout the year is maximized. One of the first addressed issues is the design of secondary optical elements whose primary optics is a Fresnel lens and which, for a fixed concentration, allow an increased acceptance angle and tolerance of the system. Several reflective and refractive secondaries have been designed and analyzed using ray tracing. In particular, using nonimaging optics and based on the single-stage design known as ‘dielectric totally internally reflecting concentrator’, a secondary with square output has been designed, fabricated and characterized. Used together with a Fresnel lens, the secondary can simultaneously achieve high efficiency, concentration and acceptance. Furthermore, an alternative method has been proposed and prototyped for the fabrication of the secondary named dome. The optics is manufactured by direct overmolding of silicone over the solar cells. One characteristic that permeates all the work done in this thesis is the holistic approach in the design of CPV modules, meaning that special attention has been paid to the joint design of the solar cell and the optics to ensure that the total system achieves the highest attainable efficiency. In this regard, many optical systems developed in the thesis have been designed, characterized and optimized considering that the current matching among the subcells within the multijunction solar cell beneath the optics must be close to one. Antireflective coating over the cell acts, somehow, as an interface between the optics and the cell. Consequently, a method has been designed to optimize antireflective coatings that takes into account not only the broad wavelength range that multijunction solar cells are sensitive to but also the angular intensity distribution created by the concentrating optics. In addition, the issue of non-uniformity has also been addressed by comparing the spectral and spatial distributions of irradiance created by different optics (simulated by ray tracing and photographed) and the efficiency losses experienced by cells illuminated by those concentrating optics experimentally determined. The effect of temperature on the concentrating optics has also been studied in this thesis. In particular, finite element simulations have been use to analyze the deformations experienced by the facets of hybrid (silicon-glass) Fresnel lenses, the change of refractive index with temperature and the influence of both effects on the system performance. A model has been implemented which take into consideration atmospheric variations, mainly temperature and spectral content of the direct normal irradiance, as well as thermal and spectral sensitivities of systems, with the aim of maximizing the energy harvested by a CPV module throughout the year in a particular location. Chapters 5 and 6 of this book are devoted to the design, fabrication, and characterization of a new concentrator concept named FluidReflex and based on a single-stage reflective optics with fluid dielectric. In this new concept, the presence of the fluid provides some significant advantages such as: an increased concentration acceptance angle product (CAP) achievable by surrounding the cell with a medium whose refractive index is greater than one, an improvement of the optical efficiency by reducing losses due to Fresnel reflection at several interfaces, an improvement in heat dissipation as the heat concentrated near the cell is transmitted by natural convection and conduction in the fluid, and an improved electrical insulation. By fabricating and characterizing several elementary-unit prototypes it was shown that there is no fundamental reason that prevents the practical implementation of this theoretical concept reaching high efficiency. Several fluid candidates were investigated proving the existence of at least to fluids that meet all the requirements (including the stability under concentrated light) to become part of the FluidReflex concentrator. Finally, several pre-industrial FluidReflex module prototypes have been designed and fabricated. An optimization process for the manufacturing of the multicavity optics was necessary to attain such an optics quality as the one achieved by the single unit. The module prototypes have been measured, both indoors and outdoors, analyzing the current matching of the solar cells beneath the concentrator for different spectral distribution of the incident irradiance. Additionally, the module showed an excellent thermal performance.

On the simulation of the UPMSAT-2 microsatellite power

Simulation of satellite subsystems behaviour is extramely important in the design at early stages. The subsystems are normally simulated in the both ways : isolated and as part of more complex simulation that takes into account imputs from other subsystems (concurrent design). In the present work, a simple concurrent simulation of the power subsystem of a microsatellite, UPMSat-2, is described. The aim of the work is to obtain the performance profile of the system (battery charging level, power consumption by the payloads, power supply from solar panels....). Different situations such as battery critical low or high level, effects of high current charging due to the low temperature of solar panels after eclipse,DoD margins..., were analysed, and different safety strategies studied using the developed tool (simulator) to fulfil the mission requirements. Also, failure cases were analysed in order to study the robustness of the system. The mentioned simulator has been programed taking into account the power consumption performances (average and maximum consumptions per orbit/day) of small part of the subsystem (SELEX GALILEO SPVS modular generators built with Azur Space solar cells, SAFT VES16 6P4S Li-ion battery, SSBV magnetometers, TECNOBIT and DATSI/UPM On Board Data Handling -OBDH-...). The developed tool is then intended to be a modular simulator, with the chance of use any other components implementing some standard data.

Durability of dielectric fluids for concentrating photovoltaic systems

Several dielectric fluids that might be used for immersing optics are analyzed in this paper. Their transmittances, both before and after an accelerated exposure to ultraviolet (UV) radiation equivalent to several years under real sun, are presented. In addition, the photocurrent losses caused by the decrease in transmittance experienced by each fluid are estimated for current III?V multijunction (MJ) solar cells. The most stable fluids were found to be paraffin and silicone oils whose transmittances remained practically unaltered after a UV dosage equivalent to 3 years of AM1.5D radiation.