Case study investigation of indoor air quality in mechanically ventilated and naturally ventilated UK social housing

There is a significant lack of indoor air quality research in low energy homes. This study compared the indoor air quality of eight
newly built case study homes constructed to similar levels of air-tightness and insulation; with two different ventilation strategies (four homes with Mechanical Ventilation with Heat Recovery (MVHR) systems/Code level 4 and four homes naturally ventilated/Code level 3). Indoor air quality measurements were conducted over a 24 h period in the living room and main bedroom of each home during the summer and winter seasons. Simultaneous outside measurements and an occupant diary were also employed during the measurement period. Occupant interviews were conducted to gain information on perceived indoor air quality, occupant behaviour and building related illnesses. Knowledge of the MVHR system including ventilation related behaviour was also studied. Results suggest indoor air quality problems in both the mechanically ventilated and naturally ventilated homes, with significant issues identified regarding occupant use in the social homes

Heat Activated Prestressing of Shape Memory Alloys for Active Confinement of Concrete Sections

This paper presents the results from the experimental investigation on heat activated prestressing of Shape Memory Alloy (SMA) wires for active confinement of concrete sections. Active confinement of concrete is found to be much more effective than passive confinement which becomes effective only when the concrete starts to dilate. Active confinement achieved using conventional prestressing techniques often faces many obstacles due to practical limitations. A class of smart materials that has recently drawn attention in civil engineering is the super elastic SMA which has the ability to undergo reversible hysteretic shape change known as the shape memory effect. The shape memory effect of SMAs can be utilized to develop a convenient prestressing technique for active confinement of concrete sections.
In this study a series of experimental tests are conducted to study Heat Activated Prestress (HAP) in SMAs. Three different types of tests are conducted with different loading protocol to determine parameters such as HAP, residual strain after heating and range of strain that can be used for effective active confinement after HAP. Test results show a maximum HAP of about 500 MPa can be achieved after heating and approximately 450MPa is retained at 25oC in specimens pre-strained by 6%. A substantial amount of strain recovery upon unloading and after heating the SMA wires is recorded. About 2.5% elastic strain recovery upon unloading from 6% strain level is observed. In the specimen pre-strained by 6%, a total of 4% strain is recovered when unloaded after heating. A strain range of 3% is found available for effective confinement after HAP. Test results demonstrate that SMAs have unique features that can be intelligently employed in many civil engineering applications including active confinement of concrete sections.

Modelling of Evaporator in Waste Heat Recovery System using Finite Volume Method and Fuzzy Technique

The evaporator is an important component in the Organic Rankine Cycle (ORC)-based Waste Heat Recovery (WHR) system since the effective heat transfer of this device reflects on the efficiency of the system. When the WHR system operates under supercritical conditions, the heat transfer mechanism in the evaporator is unpredictable due to the change of thermo-physical properties of the fluid with temperature. Although the conventional finite volume model can successfully capture those changes in the evaporator of the WHR process, the computation time for this method is high. To reduce the computation time, this paper develops a new fuzzy based evaporator model and compares its performance with the finite volume method. The results show that the fuzzy technique can be applied to predict the output of the supercritical evaporator in the waste heat recovery system and can significantly reduce the required computation time. The proposed model, therefore, has the potential to be used in real time control applications.

Calibration and validation of hydrodynamic, salt and heat transport models for Ria de Aveiro lagoon (Portugal)

Ria deAveiro is a very complex shallow water coastal lagoon located on the northwest of Portugal. Important issues would be left unanswered without a good understanding of hydrodynamic and transport processes occurring in the lagoon. Calibration and validation of hydrodynamic, salt and heat transport models for Ria de Aveiro lagoon are presented. The calibration of the hydrodynamic model was performed adjusting the bottom friction coefficient, through the comparison between measured and predicted time series of sea surface elevation for 22 stations. Harmonic analysis was performed in order to evaluate the model's accuracy. To validate the hydrodynamic model measured and predicted SSE values were compared for 11 stations, as well as main flow direction velocities for 10 stations. The salt and heat transport models were calibrated comparing measured and predicted time series of salinity and water temperature for 7 stations, and the RMS of the difference between the series was determined. These models were validated comparing the model results with an independent field data set. The hydrodynamic and the salt and heat transport models for Ria de Aveiro were successfully calibrated and validated. They reproduce accurately the barotropic flows and can therefore adequately represent the salt and heat transport and the heat transfer processes occurring in Ria deAveiro.

Nanofluids development and characterization for heat exchanging intensification

A desmaterialização da economia é um dos caminhos para a promoção do desenvolvimento sustentável na medida em que elimina ou reduz a utilização de recursos naturais, fazendo mais com menos. A intensificação dos processos tecnológicos é uma forma de desmaterializar a economia. Sistemas mais compactos e mais eficientes consomem menos recursos. No caso concreto dos sistemas envolvendo processo de troca de calor, a intensificação resulta na redução da área de permuta e da quantidade de fluido de trabalho, o que para além de outra vantagem que possa apresentar decorrentes da miniaturização, é um contributo inegável para a sustentabilidade da sociedade através do desenvolvimento científico e tecnológico. O desenvolvimento de nanofluidos surge no sentido de dar resposta a estes tipo de desafios da sociedade moderna, contribuindo para a inovação de produtos e sistemas, dando resposta a problemas colocados ao nível das ciências de base. A literatura é unânime na identificação do seu potencial como fluidos de permuta, dada a sua elevada condutividade, no entanto a falta de rigor subjacente às técnicas de preparação dos mesmos, assim como de um conhecimento sistemático das suas propriedades físicas suportado por modelos físico-matemáticos devidamente validados levam a que a operacionalização industrial esteja longe de ser concretizável. Neste trabalho, estudou-se de forma sistemática a condutividade térmica de nanofluidos de base aquosa aditivados com nanotubos de carbono, tendo em vista a identificação dos mecanismos físicos responsáveis pela condução de calor no fluido e o desenvolvimento de um modelo geral que permita com segurança determinar esta propriedade com o rigor requerido ao nível da engenharia. Para o efeito apresentam-se métodos para uma preparação rigorosa e reprodutível deste tipo de nanofluido assim como das metodologias consideradas mais importantes para a aferição da sua estabilidade, assegurando deste modo o rigor da técnica da sua produção. A estabilidade coloidal é estabelecida de forma rigorosa tendo em conta parâmetros quantificáveis como a ausência de aglomeração, a separação de fases e a deterioração da morfologia das nanopartículas. Uma vez assegurado o método de preparação dos nanofluídos, realizou-se uma análise paramétrica conducente a uma base de dados obtidos experimentalmente que inclui a visão central e globalizante da influência relativa dos diferentes fatores de controlo com impacto nas propriedades termofísicas. De entre as propriedades termofísicas, este estudo deu particular ênfase à condutividade térmica, sendo os fatores de controlo selecionados os seguintes: fluido base, temperatura, tamanho da partícula e concentração de nanopartículas. Experimentalmente, verificou-se que de entre os fatores de controlo estudados, os que maior influência detêm sobre a condutividade térmica do nanofluido, são o tamanho e concentração das nanopartículas. Com a segurança conferida por uma base de dados sólida e com o conhecimento acerca da contribuição relativa de cada fator de controlo no processo de transferência de calor, desenvolveu-se e validou-se um modelo físico-matemático com um caracter generalista, que permitirá determinar com segurança a condutividade térmica de nanofluidos.

Transient transpiration radiometer : development of a heat flux sensor for high aggressivity environments

The development of a new instrument for the measurement of convective and radiative is proposed, based on the transient operation of a transpiration radiometer. Current transpiration radiometers rely on steady state temperature measurements in a porous element crossed by a know gas mass flow. As a consequence of the porous sensing element’s intrinsically high thermal inertia, the instrument’s time constant is in the order of several seconds. The proposed instrument preserves established advantages of transpiration radiometers while incorporating additional features that broaden its applicability range. The most important developments are a significant reduction of the instrument’s response time and the possibility of separating and measuring the convective and radiative components of the heat flux. These objectives are achieved through the analysis of the instrument’s transient response, a pulsed gas flow being used to induce the transient behavior.

Thermal conductivity of building materials: an overview of its determination

A range of instruments are available to measure thermal conductivity of building materials. Some of these tools are heat-flow meter, hot plate, hot box and heat transfer analyzer. Thermal conductivity data derived by using different instruments can be different from each other. Implication of these variations in thermal conductivity is significant in terms of commercial profile of the insulations and also in terms of calculating energy saving in large scale use of that specific insulation. Thus it is important to know which of the measuring instrument for thermal conductivity can produce relatively accurate and representative result. This paper firstly looks at the methods and instrument for measuring thermal conductivity of building materials and secondly compares and analyses the results of testing thermal conductivity of fibrous insulations using a heat analyzer and a hot plate.

The comparative in situ hygrothermal performance of Hemp and Stone Wool insulations in vapour open timber frame wall panels

An in situ experiment in a full scale timber frame test building was carried out to compare the hygrothermal performance of Hemp and Stone Wool insulations of identical thermal conductivity. Hemp and Stone Wool insulations were installed in timber frame wall panels without vapour barrier. The comparison was made in terms of heat transfer properties, likelihood of mould growth and condensation. Step changes in internal relative humidity were performed to explore the effect of high and normal internal moisture load on the wall panels. No significant difference between the average equivalent thermal transmittance (U-values) of the panels incorporating Hemp and Stone Wool insulations was observed. The average equivalent U-values of the panels were closer to the calculated U-values of the panels based on the manufacturers’ declared thermal conductivity of Hemp and Stone Wool insulations. It was observed that the placement of heat flux sensor along the depth of the insulation had significant influence on the measured equivalent U-value of the panels during high internal moisture load. The frequency and likelihood of condensation was higher in the interface of Stone Wool and Oriented Strand Board (OSB). In terms of the parametric assessment of mould germination potential, relative humidity, temperature and exposure conditions in the insulation-OSB interfaces were found to be favourable to germination of mould spore. However, when the insulations were dismantled, no mould was visually detected.

Quasi steady state and dynamic hygrothermal performance of fibrous Hemp and Stone Wool insulations: Two innovative laboratory based investigations

Moisture and heat management properties of Hemp and Stone Wool insulations were studied by mounting them between a hot and a cold climate chamber. Both insulations were exposed to identical hygrothermal boundary conditions. Quasi steady state and dynamic tests were carried out at a range of relative humidity exposures. The likelihood of interstitial condensation was assessed and equivalent thermal conductivity values of the insulations were determined. The adsorption-desorption isotherms of the insulations were also determined in a dynamic vapour sorption (DVS) instrument. It was observed that the likelihood of condensation was higher in Stone Wool insulation than in Hemp insulation. Hemp insulation performed better in managing moisture due to its high hygric inertia and water absorption capacity. It was observed that the equivalent thermal conductivity of Stone Wool insulation was dependent on enthalpy flow and phase change of moisture. The equivalent thermal conductivity of Hemp insulation was close to its declared thermal conductivity in dynamic conditions when high relative humidity exposures were transient. In quasi steady state boundary conditions, when the insulation was allowed to reach the equilibrium moisture content at ranges of relative humidity, there was a moisture dependent increase of thermal conductivity in Hemp insulation.

On-line diagnostics of transformer winding insulation failures, by Park`s vector approach

This paper presents a non-invasive approach for diagnosing winding insulation failures in three-phase transformers, which is based on the on-line monitoring of the primary and secondary current Park's Vector. Experimental and simulated results demonstrate the effectiveness of the proposed technique, for detecting winding inter-turn insulation faults in operating three-phase transformers.

Geothermal Heat Pumps

If you're planning to build a new house or replace your heating and cooling system, you may want to consider a geothermal heat pump system. A GHP system can be installed in virtually any area of the country and will save energy and money. This gives tips on how to save money on heat pumps.