Avaliação do tratamento eletroquímico (direto e indireto) como alternativa de degradação do corante azul de metileno

Textile industry has been a cause of environmental pollution, mainly due to the generation of large volumes of waste containing high organic loading and intense color. In this context, this study evaluated the electrochemical degradation of synthetic effluents from textile industry containing Methylene Blue (AM) dye, using Ti/IrO2-Ta2O5 and Ti/Pt anodes, by direct and indirect (active chlorine) electrooxidation. We evaluated the influence of applied current density (20, 40 and 60 mA/cm2 ), and the presence of different concentrations of electrolyte (NaCl and Na2SO4), as well as the neutral and alkaline pH media. The electrochemical treatment was conducted in a continuous flow reactor, in which the electrolysis time of the AM 100 ppm was 6 hours. The performance of electrochemical process was evaluated by UV-vis spectrophotometry, chemical oxygen demand (COD) and total organic carbon (TOC). The results showed that with increasing current density, it was possible to obtain 100 % of color removal at Ti/IrO2-Ta2O5 and Ti/Pt electrodes. Regarding the color removal efficiency, increasing the concentration of electrolyte promotes a higher percentage of removal using 0,02 M Na2SO4 and 0,017 M NaCl. Concerning to the aqueous medium, the best color removal results were obtained in alkaline medium using Ti/Pt. In terms of organic matter, 86 % was achieved in neutral pH medium for Ti/Pt; while a 30 % in an alkaline medium. To understand the electrochemical behavior due to the oxygen evolution reaction, polarization curves were registered, determining that the presence of NaCl in the solution favored the production of active chlorine species. The best results in energy consumption and cost were obtained by applying lower current density (20 mA/cm2 ) in 6 hours of electrolysis.

Construção e avaliação de uma unidade de ensino potencialmente significativa para o conteúdo de termoquímica

Nos dias atuais, oferecer uma educação para o exercício da cidadania é função primordial das políticas públicas educacionais, conforme estabelece a constituição brasileira e a legislação de ensino. Essa função vem sendo defendida por muitos professores no Ensino Médio, atribuindo-se a disciplina de Química o papel de proporcionar um ensino crítico, participativo, reflexivo e humano. Segundo os documentos oficiais brasileiros para o Ensino de Química, o estudo do conceito de energia deve favorecer o desenvolvimento de competências para que o aluno compreenda a produção e o seu uso em diferentes fenômenos e possam interpretá-los de acordo com modelos explicativos, além de saber avaliar e julgar os benefícios e riscos da produção e do uso de diferentes formas de energia nos sistemas naturais construídos pelo homem, articulando com outras áreas de conhecimento na procura de promover a interdisciplinaridade. As unidades de ensino potencialmente significativas (UEPS), tomam como base um conjunto de teorias de aprendizagem que tem o intuito de promover um ensino com base na aprendizagem significativa e podem ajudar os estudantes nas diferentes relações que um conceito pode ter. Neste sentido, o estudo do conceito da energia a partir do trabalho com UEPS, pode ser uma importante proposta que favorece um ensino de Química na perspectiva construtivista. Assim, o objetivo deste trabalho é construir e avaliar uma proposta didática para o conteúdo de termoquímica na perspectiva das unidades de ensino potencialmente significativas de Moreira com alunos do Ensino Médio de uma escola pública do Município de Campina Grande-PB. Inicialmente a UEPS foi avaliada por 22 professores em formação inicial de duas instituições públicas de ensino superior. Em seguida, ela foi aplicada para 15 alunos do 2° ano da Escola Estadual de Ensino Médio Prof. Raul Córdula, localizada na cidade de Campina Grande-PB. A coleta dos dados para os professores em formação inicial teve como base um instrumento de validação de elaboração de unidades didáticas baseada na Engenharia Didática proposta por Artigue (1996 apud Guimarães e Giordan, 2011). Já para os alunos do ensino médio, os dados foram coletados no decorrer da UEPS e a avaliação final sobre a proposta didática ocorreu através de um questionário tomando como base a escala de Likert e o uso de mapas conceituais. Para a descrição dos dados, foram utilizados os pressupostos da análise de conteúdo de Bardin. Como produto educacional foi elaborado a Unidade de Ensino Potencialmente Significativa e um DVD contendo orientações de como trabalhar com a proposta. Os resultados deste trabalho apontam uma avaliação positiva quanto à proposta de ensino elaborada para a Educação Básica, onde se observa através do instrumento de validação aplicado, que a maioria das respostas atribuídas pelos professores, ficou entre os itens suficiente e mais que suficiente. Em relação aos momentos de aprendizagem dos alunos do Ensino Médio durante a aplicação da UEPS, foi possível observar que a proposta gerou motivação no processo de ensino e aprendizagem dos conceitos da termoquímica, como também se percebe que os mapas conceituais apresentados pelos alunos apresentaram mais proposições conceituais em uma segunda tentativa de elaboração, logo a proposta de ensino foi aprovada por mais de 90 % dos estudantes do nível médio. Portanto fica evidente que a proposta didática contribuiu no processo de ensino aprendizagem, despertando interesse e motivação nos estudantes pelo conteúdo de Termoquímica.

Efeito tardio do kinesio taping na função do membro inferior e no desempenho neuromuscular do quadríceps femoral de mulheres saudáveis: ensaio clínico e randomizado

Introduction: Kinesio Taping (KT) has been used in healthy people to improve neuromuscular performance, however, few studies have evaluated its chronic effects, despite being suggested. Objective: To analyze the chronic effects of KT on neuromuscular performance of the quadriceps, the oscillation of the center of pressure and lower limb function in healthy women. Methods: blinded, randomized, controlled trial, composed of 60 women (mean age 21.9 ± 3.3 years and BMI 22.3 ± 2.2 kg / m2) submitted to the evaluation of oscillation of the center of pressure through the baropodometry, the lower limb function by the hop test, isokinetic knee performance, the electromyographic activity of the vastus lateralis (VL) and joint position sense of the knee (JPS). Then, participants were randomly divided into three groups of twenty: control - did not apply the KT; placebo - application of KT without tension on the quadriceps; Kinesio Taping - application of KT with tension in the same muscle group. The evaluations were conducted in five moments: prior to application of KT, immediately after the application, 24h, 48h after application and 24 hours after its removal (72h). SPSS 20.0 was used for statistical analysis. The KS test was used to verify the data normality, the Levene test for homogeneity of variances and a mixed-model ANOVA 3x5 to check intra and inter-group differences. Results: there was no difference in peak torque, the power, nor the electromyographic activity or SPA (p> 0.05) between groups. The displacement speed of center of pressure reduced immediately after the application on kinesio taping group (p <0.001), but with no differences between the groups (p = 0.28). There was a reduction in the time of peak torque among the three groups in the evaluations after KT application (p <0.001) and an increase in single hop in all groups (p <0.001), but with no differences between them. Conclusion: KT can not change, in a chronic way, the lower limb function, the oscillation of the center of pressure, the isokinetic performance, the JPS of the knee and the electromyographic activity of VL muscle in healthy women.

Correlação entre força muscular do assoalho pélvico, função sexual e qualidade de vida em mulheres de meia idade

Introduction: Menopause is characterized by the depletion of ovarian follicles and the gradual decline in estradiol levels, which ends with the definitive cessation of menstrual periods (menopause). As a result of hypoestrogenism, characteristic symptoms, such as hot flashes, night sweats, vaginal dryness, dyspareunia, insomnia, mood swings and depression can be observed. There is also the weakening of the pelvic floor muscles (MAP) as a result of progressive muscle-aponeurotic and connective atrophy with consequent decreased sexual function. Objective: To evaluate the strength of MAP, sexual function and quality of life of menopausal women. Methodology: This is an observational, analytical, cross-sectional design. The sample consisted of 55 women (35 postmenopausal and 20 perimenopausal), aged between 40 and 65, who were assessed by muscle strength and perineometry test. For the assessment of sexual function and quality of life, used the Female Sexual Function Index (FSFI) and Utian Quality of Life (UQOL), respectively. Statistical analysis was performed using Pearson's correlation and multivariate analysis. Results: The mean age was 52.78 (± 6.47 years). Sexual dysfunction presented, 61.8% of participants (43.62% of postmenopausal and perimenopausal 18.17%). Muscle strength test and the maximum perineometry had a median of 3.00 (Q25: 2 e Q75: 4) and 33,50 cmH20 (Q25: 33,5 e Q75: 46,6), respectively. No correlation was found between sexual function and muscle strength (r = 0.035; p = 0.802) and between sexual function and perineometry (r = 0.126; p = 0.358). The mean total score of UQOL was 74.45 (± 12.23). Weak positive correlation was found between sexual function and quality of life (r = +0.422 p = 0.001). Multivariate analysis identified associations between sexual function and variables: quality of life, climacteric symptoms, physical activity and education level. Conclusions: These results suggest that the climacteric symptoms, quality of life, physical activity and level of education are associated with sexual function in menopausal women. However, the muscular component of sexual function needs to be further investigated in this context.

O olhar das instituições de previdência sobre a casa e a cidade: promoção, financiamento e avaliação de imóveis

The investments of Caixas and Institutos de Aposentadoria e Pensões (CAP and IAP) in homes of Natal, between the decades of 1930-60, helped to boost up the local real estate market in consolidation at the time. Inserted in the first national policy on social housing in the country, these operations have demanded the creation of a wide qualified organizational structure, which would be from the "Central Offices" of Rio de Janeiro to the decentralized units of the federal states. The professionals linked to the Local Agencies have developed, on this matter, from activities related to the design and construction of residential complexes, to the daily study of financing proposals in isolated units. As from these studies, the evaluation of shelters was essential to the effectiveness of the policy, resulting in the production of data on the market value of the properties by observing and issuing judgments upon the living quarters of different social groups. Given these considerations, the aim here is to contribute to the understanding on how to operate these real estate actions in the legitimization of boundaries about the urban space and dwellings available to workers in Natal. Therefore, the views of the city and constructions expressed by the evaluating engineers in their technical reports have been taken as the focus. Being the main primary sources of work, these reports are part of the edifices process of CAP/IAP regarding Natal, whose content is systematized in the database "Enterprises", the HCUrb Research Group. In addition, there were used local newspapers at the time and interviews with professionals as complementary sources. It was found that, in general, the evaluations have configured – in a more everyday dimension of bureaucratic routines - a vehicle, among others, circulating ideas about "home" within the social security institutions, being imbued with assumptions historically constructed about the "modern habitat". Filled in loco, the reports expose the clash between modernizing ideals in vogue and clear limitations in the city scenario at the time. Fragmented images of the town are given to read through the labels assigned to the evaluated sites – these being coated of certain "scientific" character - which both legitimated and contributed to the dynamics of appreciation/depreciation of the soil and to the socio-spatial differentiation. Contradictions were evident in the endorsement given by the technicians when financing of admittedly precarious homes for insured disadvantaged categories at the local level - such as industrial workers - while strict regulations were imposed to new construction, designed, above all, to better paid categories. By identifying raters engineers as urban agents, members of a technical-focused operating system for safety and efficiency in the real estate investments of those authorities corporatist, it is desired the usefulness of further studies on these characters, their training, professional activity and participation in the construction of discourses and practices of intervention about the city and its buildings, discussing individual and grouped interests that were left behind.

Avaliação do desempenho da paligorsquita modificada e do carvão da pirólise do lodo de esgoto no processo de degradação fotocatalítica do fenol

The uncontrolled disposal of wastewaters containing phenolic compounds by the industry has caused irreversible damage to the environment. Because of this, it is now mandatory to develop new methods to treat these effluents before they are disposed of. One of the most promising and low cost approaches is the degradation of phenolic compounds via photocatalysis. This work, in particular, has as the main goal, the customization of a bench scale photoreactor and the preparation of catalysts via utilization of char originated from the fast pyrolysis of sewage sludge. The experiments were carried out at constant temperature (50°C) under oxygen (410, 515, 650 and 750 ml min-1). The reaction took place in the liquid phase (3.4 liters), where the catalyst concentration was 1g L-1 and the initial concentration of phenol was 500 mg L-1 and the reaction time was set to 3 hours. A 400 W lamp was adapted to the reactor. The flow of oxygen was optimized to 650 ml min-1. The pH of the liquid and the nature of the catalyst (acidified and calcined palygorskite, palygorskite impregnated with 3.8% Fe and the pyrolysis char) were investigated. The catalytic materials were characterized by XRD, XRF, and BET. In the process of photocatalytic degradation of phenol, the results showed that the pH has a significant influence on the phenol conversion, with best results for pH equal to 5.5. The phenol conversion ranged from 51.78% for the char sewage sludge to 58.02% (for palygorskite acidified calcined). Liquid samples analyzed by liquid chromatography and the following compounds were identified: hydroquinone, catechol and maleic acid. A mechanism of the reaction was proposed, whereas the phenol is transformed into the homogeneous phase and the others react on the catalyst surface. For the latter, the Langmuir-Hinshelwood model was applied, whose mass balances led to a system of differential equations and these were solved using numerical methods in order to get estimates for the kinetic and adsorption parameters. The model was adjusted satisfactorily to the experimental results. From the proposed mechanism and the operating conditions used in this study, the most favored step, regardless of the catalyst, was the acid group (originated from quinone compounds), being transformed into CO2 and water, whose rate constant k4 presented value of 0.578 mol L-1 min-1 for acidified calcined palygorskite, 0.472 mol L-1 min-1 for Fe2O3/palygorskite and 1.276 mol L-1 min-1 for the sludge to char, the latter being the best catalyst for mineralization of acid to CO2 and water. The quinones were adsorbed to the acidic sites of the calcined palygorskite and Fe2O3/palygorskite whose adsorption constants were similar (~ 4.45 L mol-1) and higher than that of the sewage sludge char (3.77 L mol-1).

Avaliação do desempenho da paligorsquita modificada e do carvão da pirólise do lodo de esgoto no processo de degradação fotocatalítica do fenol

The uncontrolled disposal of wastewaters containing phenolic compounds by the industry has caused irreversible damage to the environment. Because of this, it is now mandatory to develop new methods to treat these effluents before they are disposed of. One of the most promising and low cost approaches is the degradation of phenolic compounds via photocatalysis. This work, in particular, has as the main goal, the customization of a bench scale photoreactor and the preparation of catalysts via utilization of char originated from the fast pyrolysis of sewage sludge. The experiments were carried out at constant temperature (50°C) under oxygen (410, 515, 650 and 750 ml min-1). The reaction took place in the liquid phase (3.4 liters), where the catalyst concentration was 1g L-1 and the initial concentration of phenol was 500 mg L-1 and the reaction time was set to 3 hours. A 400 W lamp was adapted to the reactor. The flow of oxygen was optimized to 650 ml min-1. The pH of the liquid and the nature of the catalyst (acidified and calcined palygorskite, palygorskite impregnated with 3.8% Fe and the pyrolysis char) were investigated. The catalytic materials were characterized by XRD, XRF, and BET. In the process of photocatalytic degradation of phenol, the results showed that the pH has a significant influence on the phenol conversion, with best results for pH equal to 5.5. The phenol conversion ranged from 51.78% for the char sewage sludge to 58.02% (for palygorskite acidified calcined). Liquid samples analyzed by liquid chromatography and the following compounds were identified: hydroquinone, catechol and maleic acid. A mechanism of the reaction was proposed, whereas the phenol is transformed into the homogeneous phase and the others react on the catalyst surface. For the latter, the Langmuir-Hinshelwood model was applied, whose mass balances led to a system of differential equations and these were solved using numerical methods in order to get estimates for the kinetic and adsorption parameters. The model was adjusted satisfactorily to the experimental results. From the proposed mechanism and the operating conditions used in this study, the most favored step, regardless of the catalyst, was the acid group (originated from quinone compounds), being transformed into CO2 and water, whose rate constant k4 presented value of 0.578 mol L-1 min-1 for acidified calcined palygorskite, 0.472 mol L-1 min-1 for Fe2O3/palygorskite and 1.276 mol L-1 min-1 for the sludge to char, the latter being the best catalyst for mineralization of acid to CO2 and water. The quinones were adsorbed to the acidic sites of the calcined palygorskite and Fe2O3/palygorskite whose adsorption constants were similar (~ 4.45 L mol-1) and higher than that of the sewage sludge char (3.77 L mol-1).

Avaliação do efeito do extrato hidroalcoólico das folhas de Anacardium occidentale L. em ratos submetidos à colite ulcerativa

Ulcerative colitis is a chronic disease characterized by inflammation in the intestinal mucosa, in most cases affects the colon and rectum. The therapeutic drugs are used as aminosalicylates and glucocorticosteroids, but due to the low response and the various side effects caused by them, reveals the need to search for new sources of useful compounds in the treatment of this disease.The species Anacardium occidentale popularly known as cashew, has been used for centuries in folk medicine in the healing aid of skin and mucosa lesions.Recent studies show its expressive antiulcerogenic effect, what we instigated to assess the effect of the extract of A. occidentaleleaves in rats with acute ulcerative colitis, therefore, 42 rats were used male Wistar, divided into 06 groups, and Negative Control (C) Positive Control (C +), treated with Sulfasalazine (Sz500) and treated with Extract A. occidentale at doses of 50 (Ao50), 100 (Ao100) and 200 mg / kg (Ao200).All groups were submitted to experimental colitis Ulcerative except C-, moreover, C- and C + received saline via gavage for 7 consecutive days while the other groups received their respective treatments.Euthanasia of animals took place on the 8th day in which it was collected intestinal colon sample for later analysis macroscopic, histopathological, morphometric and biochemistry, as well as complementary collection of blood and liver tissue. The extract is rich in saponins and phenolic compounds such as flavonoids (quercetin and kaempferol) and tannins.When the Sz500 groups and 100 showed significant protection to damage to lipids and proteins, among the groups subjected to experimental ulcerative colitis, the animals Ao100 group obtained the lowest score in all parameters analyzed.Treatment with 100 mg / kg of A. occidentale extract seems to have a combination of antiinflammatory, antioxidant, bactericidal and anabolic promoted by the bioactive compounds present in the extract.However, it is necessary to investigate harder treating dose of 100mg / kg to higher doses compared to elucidate more properly the best therapeutic dosage ulcerative colitis.

Reabilitação cardíaca na insuficiência cardíaca crônica: efeitos de 12 semanas de treinamento intervalado x contínuo na função cardiopulmonar e qualidade de vida

Background: Cardiac Rehabilitation (CR) has effect on mortality in patients with heart failure (HF) chronic, and the exercise of the treatment of this patient. The most common exercise is ongoing training. Recently we have been studying the effects of interval training, but there is no consensus on the optimal dose of exercise. Objective: To evaluate the effects of interval aerobic training are superior to continuous aerobic training in patients with chronic HF. Methods: The clinical trial evaluated patients through cardiopulmonary test (CPX) and quality of life before and after the RC (3 times / 12 weeks). Patients were randomized into Group Interval Training (GTI - 85% of heart rate reserve - FCR), Continuous Training Group (GTC - 60% of HRR) and control group (CG) who received guidelines. Results: 18 patients were evaluated (mean age 44.7 ± 13.2 years and 35.2 ± 8.9% of left ventricular ejection fraction [LVEF]). Both groups were efficient to increase the peak VO2 and 15.1% (P = 0.02) in GTI and 16.1% (P = 0.01) GTC. As for the quality of life the GTI GTC showed improvement compared to the control group (P = 0.006). Hemodynamic mismatch events during the CPX were reduced after training in more GTC (patients 1 to 4) than in the GTI (5 to 3). Cardiac risk also decreased in the GTC (3 patients left the severe risk to take after training). Conclusion: Continuous training becomes more appropriate for improving fitness with little chance of developing cardiac event patients with chronic HF.

Efeito do treinamento muscular inspiratório com diferentes cargas na força e função de músculos respiratórios

Background: The inspiratory muscle training (IMT) has been considered an option in reversing or preventing decrease in respiratory muscle strength, however, little is known about the adaptations of these muscles arising from the training with charge. Objectives: To investigate the effect of IMT on the diaphragmatic muscle strength and function neural and structural adjustment of diaphragm in sedentary young people, compare the effects of low intensity IMT with moderate intensity IMT on the thickness, mobility and electrical activity of diaphragm and in inspiratory muscles strength and establish a protocol for conducting a systematic review to evaluate the effects of respiratory muscle training in children and adults with neuromuscular diseases. Materials and Methods: A randomized, double-blind, parallel-group, controlled trial, sample of 28 healthy, both sexes, and sedentary young people, divided into two groups: 14 in the low load training group (G10%) and 14 in the moderate load training group (G55%). The volunteers performed for 9 weeks a home IMT protocol with POWERbreathe®. The G55% trained with 55% of maximal inspiratory pressure (MIP) and the G10% used a charge of 10% of MIP. The training was conducted in sessions of 30 repetitions, twice a day, six days per week. Every two weeks was evaluated MIP and adjusted the load. Volunteers were submitted by ultrasound, surface electromyography, spirometry and manometer before and after IMT. Data were analyzed by SPSS 20.0. Were performed Student's t-test for paired samples to compare diaphragmatic thickness, MIP and MEP before and after IMT protocol and Wilcoxon to compare the RMS (root mean square) and median frequency (MedF) values also before and after training protocol. They were then performed the Student t test for independent samples to compare mobility and diaphragm thickness, MIP and MEP between two groups and the Mann-Whitney test to compare the RMS and MedF values also between the two groups. Parallel to experimental study, we developed a protocol with support from the Cochrane Collaboration on IMT in people with neuromuscular diseases. Results: There was, in both groups, increased inspiratory muscle strength (P <0.05) and expiratory in G10% (P = 0.009) increase in RMS and thickness of relaxed muscle in G55% (P = 0.005; P = 0.026) and there was no change in the MedF (P> 0.05). The comparison between two groups showed a difference in RMS (P = 0.04) and no difference in diaphragm thickness and diaphragm mobility and respiratory muscle strength. Conclusions: It was identified increased neural activity and diagrammatic structure with consequent increase in respiratory muscle strength after the IMT with moderate load. IMT with load of 10% of MIP cannot be considered as a placebo dose, it increases the inspiratory muscle strength and IMT with moderate intensity is able to enhance the recruitment of muscle fibers of diaphragm and promote their hypertrophy. The protocol for carrying out the systematic review published in The Cochrane Library.

Caracterização e avaliação da atividade fotocatalítica de catalisadores baseados no TiO2, sintetizados mediante hidrólise em uma mistura de solventes

This study involved the synthesis of photocatalysts based on titanium dioxide (TiO2). The photocatalysts were synthesized by the sol-gel method using three different proportions of acetone (25%, 50% and 75% v/v) in water/acetone mixtures, in order to control the hydrolysis of the precursor of titanium (titanium tetraisopropoxide). Aiming to investigate the structural, morphological and electronic changes provoked by the use of the solvent mixtures, different methodologies were used to characterize the oxides, such as X-ray diffraction (XRD), RAMAN spectroscopy, UV-Vis diffuse reflectance spectroscopy, and measurements of specific surface area (BET). XRD combined to RAMAN analyses revealed that the products are two-phase highly crystalline oxides involving anatase as main phase and brookite. Besides, the refined XRD using the method of Rietveld demonstrated that the presence of acetone during the synthesis influenced in the composition of the crystalline phases, increasing the proportion of the brookite phase between 13 and 22%. The band gap energy of these oxides practically did not suffer changes as function of the synthesis conditions. As shown by the isotherm, these photocatalysts are mesoporous materials with mean diameter of pores of 7 nm and approximately 20% of porosity. The surface area of the oxides prepared by hydrolysis in presence of acetone was 12% higher compared to the bare oxide. After characterized, these oxides had their photocatalytic activities evaluated by photodegradation of the azo dyes Ponceau 4R (P4R), Tartrazine (TTZ) and Reactive Red 120 (RR120), and also by the ability to mediate the photocatalytic production of hydrogen. Using the most efficient photocatalyst, the mineralization achieved for the dyes P4R, RR120 and TTZ was of respectively 83%, 79% and 56% in 120 minutes of reaction, while the discoloration of P4R e RR120 reached 100% and 94% for TTZ. In addition, the same photocatalyst in the presence of 0.5% w/w of Platinum and suspended in a 5:1 v/v water/methanol mixture, produced 56 mmol of gaseous hydrogen in five hours of experiment, corresponding to a specific rate of hydrogen production of 139.5 mmol h-1 g-1.

Avaliação tribológica de novas modificações superficiais para cilindros de laminação a frio

The present work analyzed the tribological behavior of coatings/surface modifications traditionally used in cold rolling mill rolls and new coatings/surface modificationswith potential to replace the carcinogenic hard chrome. The study started with identification of wear mechanisms occurring in real coldrollingmill rolls. Due the high cost and dimensions of the rolls, thereplication technique was used. Replicas were obtained from 4 different rolling millBrazilian companies before and after a normal rolling campaign. Initial sliding tests were conducted using spherical and cylindrical counter bodies in order to verifywhichtribological conditions allowed to reproduce the wear mechanisms found in the replicas. These tests indicated the use of reciprocating sliding tests with cylindrical counter bodies (line contact), normal load of 100 N, and test times of and 1 h and 5 h. Different surface modifications were carried out on samples produced from a fragment of a rolling mill roll. The specimens were heat treated and ground on both sides. After, some specimens were surface textured by electrical discharge texturing (EDT). For both groups (ground and EDT), subsequent treatments of chromium plating, electroless NiP coating and plasma nitriding were carried out. The results of the reciprocating tests showed that specimens with electroless NiP coating presented the lowest friction coefficients, while plasma nitrided specimens showed the highest. In general, previous surface texturing before the coating/surface modification increased the wear of the counter bodies. Oneexceptionwas for EDT with subsequent electroless NiP coating, which presented the lowest counter bodies wear rate. The samples withelectroless NiP coating promoted a tribolayer consisting of Nickel, Phosphorus and Oxygen on both the specimens andthecounter bodies, which was apparently responsible for the reduction of friction coefficient and wear rate. The increase of the test time reduced the wear rate of the samples, apparently due the stability of the tribolayers formed, except for the nitrided samples. For the textured specimens, NiP coating showed the best performance in maintaining the surface topography of the specimens after the sliding tests.

Avaliação da soldagem GMAW mecanizada e automatizada para união de dutos utilizando fontes convencional e com controle de curto- circuito

Welding is one of the most employed process for joining steel pipes. Although, manual welding is still the most used one, mechanized version and even automatized one have increased its demand. Thus, this work deals with girth welding of API 5L X65 pipes with 8” of nominal diameter and 8.0 mm thickness, beveled with V-30º narrow gap. Torch is moved by a bug carrier (mechanized welding) and further the parameters are controlled as a function of angular position (automatized welding). Welding parameters are presented for filling the joint with two-passes (root and filling/capping passes). Parameters for the root pass were extracted from previous author´s work with weldments carried out in plates, but validated in this work for pipe welding. GMAW processes were assessed with short-circuit metal transfer in both conventional and derivative modes using different technologies (RMD, STT and CMT). After the parameter determination, mechanical testing was performed for welding qualification (uniaxial tension, face and root bending, nick break, Charpy V-notch impact, microhardness and macrograph). The initially obtained results for RMD and CMT were acceptable for all testing and, in a second moment, also for the STT. However, weld beads carried out by using the conventional process failed and revealed the existence of lack of fusion, which required further parametrization. Thus, a Parameter-Variation System for Girth Welding (SVP) was designed and built to allow varying the welding parameters as a function of angular position by using an inclinometer. The parameters were set for each of the three angular positions (flat, vertical downhill and overhead). By using such equipment and approach, the conventional process with parameter variation allowed reducing the welding time for joint accomplishment of the order of 38% for the root pass and 30% for the filling/capping pass.

A importância da qualidade na avaliação em formato a distância

Relatório de estágio para obtenção do grau de mestre em Educação e Comunicação Multimédia

Avaliação comparativa da remodelação óssea periimplantar em implantes com junção cone-morse e hexágono externo: estudo clínico randomizado controlado, duplo cego, boca dividida

Background: Several theories, such as the biological width formation, the inflammatory reactions due to the implant-abutment microgap contamination, and the periimplant stress/strain concentration causing bone microdamage accumulation, have been suggested to explain early periimplant bone loss. However, it is yet not well understood to which extent the implant-abutment connection type may influence the remodeling process around dental implants. Aim: to evaluate clinical, bacteriological, and biomechanical parameters related to periimplant bone loss at the crestal region, comparing external hexagon (EH) and Morse-taper (MT) connections. Materials and methods: Twelve patients with totally edentulous mandibles received four custom made Ø 3.8 x 13 mm implants in the interforaminal region of the mandible, with the same design, but different prosthetic connections (two of them EH or MT, randomly placed based on a split-mouth design), and a immediate implant- supported prosthesis. Clinical parameters (periimplant probing pocket depth, modified gingival index and mucosal thickness) were evaluated at 6 sites around the implants, at a 12 month follow-up. The distance from the top of the implant to the first bone-to-implant contact – IT-FBIC was evaluated on standardized digital peri-apical radiographs acquired at 1, 3, 6 and 12 months follow-up. Samples of the subgingival microbiota were collected 1, 3 and 6 months after implant loading. DNA were extracted and used for the quantification of Tanerella forsythia, Porphyromonas gingivalis, Aggragatibacter actinomycetemcomitans, Prevotella intermedia and Fusobacterium nucleatum. Comparison among multiple periods of observation were performed using repeated-measures Analysis of Variance (ANOVA), followed by a Tukey post-hoc test, while two-period based comparisons were made using paired t- test. Further, 36 computer-tomographic based finite element (FE) models were accomplished, simulating each patient in 3 loading conditions. The results for the peak EQV strain in periimplant bone were interpreted by means of a general linear model (ANOVA). Results: The variation in periimplant bone loss assessed by means of radiographs was significantly different between the connection types (P<0.001). Mean IT-FBIC was 1.17±0.44 mm for EH, and 0.17±0.54 mm for MT, considering all evaluated time periods. All clinical parameters presented not significant differences. No significant microbiological differences could be observed between both connection types. Most of the collected samples had very few pathogens, meaning that these regions were healthy from a microbiological point of view. In FE analysis, a significantly higher peak of EQV strain (P=0.005) was found for EH (mean 3438.65 µ∑) compared to MT (mean 840.98 µ∑) connection. Conclusions: Varying implant-abutment connection type will result in diverse periimplant bone remodeling, regardless of clinical and microbiological conditions. This fact is more likely attributed to the singular loading transmission through different implant-abutment connections to the periimplant bone. The present findings suggest that Morse-taper connection is more efficient to prevent periimplant bone loss, compared to an external hexagon connection.