Treatment of PVC using an alternative low energy ion bombardment procedure

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Orientation dependence of stored energy of cold work in semi-processed electrical steels after temper rolling

Microhardness measurements were carried out in a low carbon lamination steel after 6% of temper rolling, in order to evaluate local variations of work hardening as a function of crystallographic orientation. EBSD (electron back scattered diffraction) was used to determine grain orientations with respect to individual rolling planes and rolling directions. Hardness was shown to increase with the local Taylor factor. TEM observations and a well-known dislocation hardening model were used to confirm the equivalence between hardness values and the stored energy of cold work. A definite correlation between stored energy and Taylor factors could therefore be established, being more consistent than previous data reported in the literature. The improvement was thought to be related to the rather small plastic deformation, during which Taylor factors could be considered to remain constant. (c) 2006 Elsevier B.V. All rights reserved.

On the optimum parameters of a device for harvesting energy from running and walking

This paper investigates the feasibility of using an energy harvesting device tuned such that its natural frequency coincides with higher harmonics of the input to capture energy from walking or running human motion more efficiently. The paper starts by reviewing the concept of a linear resonant generator for a tonal frequency input and then derives an expression for the power harvested for an input with several harmonics. The amount of power harvested is estimated numerically using measured data from human subjects. Assuming that the input is periodic, the signal is reconstructed using a Fourier series before being used in the simulation. It is found that although the power output depends on the input frequency, the choice of tuning the natural frequency of the device to coincide with a particular higher harmonic is restricted by the amount of damping that is needed to maximize the amount of power harvested, as well as to comply with the size limit of the device. It is also found that it is not feasible to tune the device to match the first few harmonics when the size of the device is small, because a large amount of damping is required to limit the motion of the mass.

Energy and amino acid content in phase 1 nursery diet: piglet performance and body chemical composition

Avaliaram-se os efeitos da densidade de energia metabolizável (EM) e lisina digestível (LIS) sobre o desempenho e a composição corporal de leitões após o desmame. Utilizaram-se 114 animais desmamados aos 7,4 ± 0,80 kg; desses animais, 108 foram alojados na unidade de creche e 6 foram abatidos no dia do desmame para determinação dos dados comparativos da composição química corporal. Seis densidades de nutrientes foram estipuladas a partir de estudo anterior, com base na maior retenção de nitrogênio, mantendo-se as seguintes relações EM:LIS nas dietas experimentais: 3.390:1,291; 3.450:1,409; 3.650:1,411; 3.780:1,461; 3.940:1,507; e 4.109 kcal/kg EM:1,564% LIS. As dietas experimentais foram oferecidas durante 13 dias, quando os leitões atingiram o peso de 12,986 ± 1,449 kg. Avaliaram-se os prováveis efeitos residuais da densidade nutricional no desempenho subseqüente dos leitões. Ao término da fase inicial-1, seis leitões de cada densidade foram abatidos para determinação da composição química nas frações corporais e no corpo vazio. Não houve influência significativa dos níveis nutricionais no desempenho dos leitões ao término da avaliação. Os resultados de conversão alimentar e composição corporal ratificam o nível indicado em estudo anterior, de 4 g LIS/Mcal. O aumento da densidade de energia e lisina confirma a necessidade da correta relação entre ambos para assegurar o melhor desempenho dos leitões na fase inicial de crescimento.

Flexural strength of acrylic resin repairs processed by different methods: water bath, microwave energy and chemical polymerization

Denture fractures are common in daily practice, causing inconvenience to the patient and to the dentists. Denture repairs should have adequate strength, dimensional stability and color match, and should be easily and quickly performed as well as relatively inexpensive. Objective: The aim of this study was to evaluate the flexural strength of acrylic resin repairs processed by different methods: warm water-bath, microwave energy, and chemical polymerization. Material and methods: Sixty rectangular specimens (31x10x2.5 mm) were made with warm water-bath acrylic resin (Lucitone 550) and grouped (15 specimens per group) according to the resin type used to make repair procedure: 1) specimens of warm water-bath resin (Lucitone 550) without repair (control group); 2) specimens of warm water-bath resin repaired with warm water-bath; 3) specimens of warm water-bath resin repaired with microwave resin (Acron MC); 4) specimens of warm water-bath resin repaired with autopolymerized acrylic resin (Simplex). Flexural strength was measured with the three-point bending in a universal testing machine (MTS 810 Material Test System) with load cell of 100 kgf under constant speed of 5 mm/min. Data were analyzed statistically by Kruskal-Wallis test (p<0.05). Results: The control group showed the best result (156.04 +/- 1.82 MPa). Significant differences were found among repaired specimens and the results were decreasing as follows: group 3 (43.02 +/- 2.25 MPa), group 2 (36.21 +/- 1.20 MPa) and group 4 (6.74 +/- 0.85 MPa). Conclusion: All repaired specimens demonstrated lower flexural strength than the control group. Repairs with autopolymerized acrylic resin showed the lowest flexural strength.