Análise de cilindros de paredes grossas através do método dos elementos finitos

Have long studied the distribution of stresses in the cylinder. When this thickness is less than or equal to 10% of the inner radius is possible to consider a uniform distribution along the thickness of the tube. However, when the thickness is greater than 10% of the inner radius is necessary to consider the theory of thick-walled cylinders. This theory shows that when the thickness increases on the radius, the stresses do not act uniformly. The objective of this study is to determine the maximum stresses in thick-walled cylinders by comparing the results obtained by the theory of elasticity and the finite element method

Parque público como reestruturador de elementos urbanos: revitalização da antiga siderúrgica de Lençóis Paulista

The intention of this survey is develop design actions about the site of the former steel from Lençóis Paulista, a large and impressive area, but underutilized in the town. The aim is to revitalize it since the analysis and knowledge from the place and its surroundings, in order to solve the analysis observed: the non integration of the town, neighborhoods and public adjacent devices with the interior of the mentioned spot

Otimização do braço inferior da suspensão dianteira do veículo Baja utilizando o método dos elementos finitos

Mass reduction coupled with the mechanical performance in service has been the goal of many projects related to the transport area, considering the advantages that mass reduction can bring. However, make a simple material substitution without design a new geometry to corroborate for the best component performance, often makes the replacement unviable. In this study, it was investigated the advantages of replacing the prototype BAJA SAE front suspension lower arm of Equipe Piratas do Vale de BAJA SAE - Universidade Paulista, Campus Guaratinguetá, actually produced with steel, for a new component made of carbon fiber composite. The new geometry has been developed to provide the best possible performance for this component and your easy manufacturing. The study was done using the 3D modeling tools and computer simulations via finite element method. The first stage of this work consisted on calculation of the estimated maximum contact force tire / soil in a prototype landing after jump at one meter high, drop test in the laboratory with the current vehicle, current front suspension lower arm 3D modeling, finite element simulation and analysis of critical regions. After all current component analysis, a new geometry for the part in study was designed and simulated in order to reduce the component mass and provide a technological innovation using composite materials. With this work it was possible to obtain a theoretical component mass reduction of 25,15% maintaining the mechanical strength necessary for the appropriated component performance when incited

Modelagem em 3D de uma patela humana e análise de esforços utilizando o método dos elementos finitos

Throughout the history of medicine surgeons realized the importance of the patella to the functioning of the knee. The main function of the patella is to increase the mechanical efficiency of the quadriceps tendon and knee extensor mechanism. It was found that 50% to 80% of the fractures without deviation of the patella have the transversal pattern, possibly due to excessive tensile forces applied to the extensor mechanism. The purpose of this study is to analyze the loads to which a patella is submitted during a normal extension movement of knee. This analysis will be done by modeling a 3D patella and subsequent load simulation as, described in medical literature, using the finite element method

Estudo de placas elásticas pelo metodo dos elementos de contorno

Este trabajo tiene como objetivo principal oferecer una herramienta alternativa para la resolución de placas finas, presentes en edifícios, relacionadas con los métodos de cálculo adquiridos durante la universidad, calculo a través de tablas con pocas condiciones de controno. El método utilizado es el Método de los elementos de contorno que discretiza la placa en partes finitas, aproximando los resultados obtenidos a valores reales. En este trabajo se ha utilizado el programa de ordenador Placas2.for (TAGUTI,Y. 2010) basado en el Método de los elementos de contorno para la resolución de las placas finas con varias condiciones de contorno geométricas y de cargas

As influências da especialização formativa na prática docente dos egresos do curso de graduação em Geografia da UNESP - Rio Claro

The present paper is a reflection of studies and analyzes on issues involving the training of Geography Teachers. By realizing this projetc, we aim to analyze the influences of specialization training in the teaching practice of the subjects who graduated in Geography at the Universidade Estadual Paulista Júlio de Mesquita Filho, Rio Claro Campus. This is primarily a discussion of the university curriculum, the professionals it forms and the current politics of training teachers of Geography. Thus, we conducted a literature review, and will be used questionnaires and interviews with the subjects, graduated in degree course and a BA in Geography in the last four years

Caracterização físico-mecânica de elementos estruturais roliços perfilados de Amaru

The study of physical and mechanical properties of wood is essential for its structural use and it is of great importance to the construction industry. Thus, this study aimed to determine the physical and mechanical properties of the wood Amaru - a hybrid of Eucalyptus, developed by Plantar Projects and Forest Products Ltda. In order to determine the properties of Amaru, round samples were used, which were provided to the Laboratory of Wood and Wooden Structures of the School of Engineering of São Carlos, University of São Paulo - LaMEM / EESC / USP. For the characterization of the physical properties, the apparent specific gravity and moisture content of the samples were determined. To the mechanical characterization, the following properties were evaluated: strength and stiffness in compression, strength and stiffness in bending, shear and tension. The procedures of the tests performed in this study were done according to the recommendations of the Brazilian Wood Standard ABNT NBR 7190:1997. The specimen used were confectioned in actual dimensions, according to as those used in the construction system proposed by Plantar. The results obtained from the tests performed showed that the mechanical properties approached the values proposed by the Wood Standard NBR 7190. The visual grading was important to provide a primary idea about the failure modes to be obtained from the tests performed. The bending test showed the modulus of elasticity (MOE) and Modulus of Rupture (MOR), which resulted in 15822 MPa and 101,7 MPa, respectively. The compression test resulted in values Ec0,m and fc0, 15698 MPa and 50,7 MPa. The tensile strength (ft0) of this hybrid was calculated and its value obtained was 60,8 MPa. The shear strength (fv0) was 8,2 MPa. The results obtained from the tests are the basis for engineers and architects to design structures using wood species Amaru

Análise de falhas por fadiga de alto ciclo em eixos de transmissão utilizando o método dos elementos finitos

This work presents a study that aims to validate the fatigue analyses developed on finite element commercial software, ANSYS Workbench. It was based on mechanical tests development of traction and hardness, to verify the mechanical properties of material that the shaft was manufactured (ABNT 1045 steel), it was developed bend test, with purpose to prove the confiability degree of computational analyses, obtaining the maximum stress in a work condition determined with 40 [kgf] of load applied, and at the end, was developed the fatigue test to obtain the number of cycles that the transmission shaft can support in a work condition with 8 [kgf] of load applied. The results obtained during the work present, have to be quite satisfactory with the theoretically expected

Espectrometria de massa para análise isotópica dos bio-elementos

Mass spectrometry is an analytical technique widely used in several areas of academic research. It allows the knowledge of the information about the micro-world of atoms leading to significant advances in science today. The analysis of stable isotopes of carbon, hydrogen, oxygen, nitrogen and sulfur, also known as bio-elements, shows itself as a major area of interest in using the proposed method. The development of techniques and equipment coupled with mass spectrometry promises to deliver even greater progress in this field, in particular, for the biological sciences and related areas. The pyrolytic method in reduction of organic compounds at high temperatures provides simultaneous isotopic analysis of bio-elements H and O, by the gases released, H2 and CO after the pyrolitic process, significantly reducing analysis time and the amount of material to sample. This paper presents a review of mass spectrometry with its basic principles of operation, and pyrolytic method for reducing compounds at temperatures above 1400 ° C for isotopic analysis of bio-elements

Estudos de elementos repetitivos presentes no genoma da espécie Schizodon borelli (Characiformes: Anostomidae)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Concentração de tensões em peças e componentes estruturais - uma abordagem através do método dos elementos finitos

Any failure process that may occur in a part probably is located where the stress exceeded the level of resistance. When a part or component has a sharp change in geometry, such as slots, holes, grooves, bumps or other irregularities, there is an increased concentration of stress at a specific location of the part. The objective of this study is to determine the maximum stresses in structural parts and components using the equations of elasticity theory in conjunction with the stress concentration factor experiment and compare them with results obtained by finite element method

Análise estrutural de treliças espaciais no software Excel utilizando o médodo dos elementos finitos

The following paper means to develop a program to make structural analysis of space trusses. The program to be implemented was based on the concepts of the finite element method and used the programing resources of Visual Basic for Applications (VBA) for the Excel Software®. Being Excel® a software of easy access, low cost, capacity to make matrix calculations and with advanced resources of VBA programing, it is possible to develop an economic solution, efficient and precise for structural analysis of space trusses. Firstly is presented a finite elemento method and the space truss. Then is developed a few important algorithms to be used during the development of the program and also the use of a few resources of VBA. And to validate the quality, efficiency and precision of the results, these are compared with the established commercial software Ansys

Comunicação científica: agregação, compartilhamento e reuso de elementos informacionais

Pós-graduação em Ciência da Informação - FFC

Efeito da aplicação de água residuária de graxaria em elementos químicos do solo e na produção e composição mineral de duas espécies forrageiras

Pós-graduação em Agronomia (Ciência do Solo) - FCAV

Psicologia do trânsito e competência moral: uma intervenção junto a alunos de um curso de especialização

Pós-graduação em Educação - FFC