Evaluation of the dioxin and furan formation thermodynamics in combustion processes of urban solid wastes

Specific combustion programs (Gaseq, Chemical equilibria in perfect gases, Chris Morley) are used to model dioxin and formation in the incineration processes of urban solid wastes. Thanks to these programs, it is possible to establish correlations with the formation mechanisms postulated in literature on the subject. It was found that minimum oxygen quantities are required to obtain a significant formation of these compounds and that more furans than dioxins are formed. Likewise, dioxin and furan formation is related to the presence of carbon monoxide, and dioxin and furan distribution among its different compounds depends on the chlorine and hydrogen relative composition. This is due to the fact that an increased chlorine availability leads to the formation of compounds bearing a higher chlorine concentration (penta-, hexa-, hepta-, and octachlorides), whereas an increased hydrogen availability leads to the formation of compounds bearing a lower chlorine number (mono, di-, tri-, and tetrachlorides).

Argentimetric assay of ranitidine in bulk drug and in dosage forms

Two simple, rapid and cost-effective methods based on titrimetric and spectrophotometric techniques are described for the assay of RNH in bulk drug and in dosage forms using silver nitrate, mercury(II)thiocyanate and iron(III)nitrate as reagents. In titrimetry, an aqueous solution of RNH is treated with measured excess of silver nitrate in HNO3 medium, followed by determination of unreacted silver nitrate by Volhard method using iron(III) alum indicator. Spectrophotometric method involve the addition a known excess of mercury(II)thiocyanate and iron(III)nitrate to RNH, followed by the measurement of the absorbance of iron(III)thiocyante complex at 470 nm. Titrimetric method is applicable over 4-30 mg range and the reaction stoichiometry is found to be 1:1 (RNH: AgNO3). In the spectrophotometric method, the absorbance is found to increase linearly with concentration of RNH which is corroborated by the correlation coefficient of 0.9959. The system obey Beer's law for 5-70 µg mL-1. The calculated apparent molar absorptivity and sandell sensitivity values are found to be 3.27 ´ 10³ L mol-1 cm-1, 0.107 µg cm-2 respectively. The limits of detection and quantification are also reported for the spectrophotometric method. Intra-day and inter-day precision and accuracy of the methods were evaluated as per ICH guidelines. The methods were successfully applied to the assay of RNH in formulations and the results were compared with those of a reference method by applying Student's t and F-tests. No interference was observed from common pharmaceutical excipients. The accuracy of the methods was further ascertained by performing recovery tests by standard addition method.

Efeitos de oxidantes e sais inorgânicos na degradação fotocatalítica do herbicida imazetapir mediada por dióxido de titânio

A degradação fotocatalítica de imazetapir, um herbicida da família das imidazolinonas, em suspensão aquosa de dióxido titânio foi investigada na presença de dois receptores de elétrons como persulfato de potássio e periodato de sódio, assim como na presença de dois sais inorgânicos como sulfato de sódio e dihidrogenofosfato de sódio a 30ºC. O modelo cinético de pseudo-primeira ordem foi empregado para discutir os resultados. O desaparecimento de imazetapir em função do tempo de irradiação foi analisado por cromatografia líquida de alta eficiência. Entre os dois oxidantes estudados a degradação foi mais rápida quando se adicionou o periodato de sódio, enquanto a presença do sulfato de sódio retarda a degradação de imazetapir mais que o dihidrogenofosfato na suspensão de TiO2.

Adsorption isotherm studies of Cd (II), Pb (II) and Zn (II) ions bioremediation from aqueous solution using unmodified and EDTA-modified maize cob

The need to clean-up heavy metal contaminated environment can not be over emphasized. This paper describes the adsorption isotherm studies of Cd (II), Pb (II) and Zn (II) ions from aqueous solution using unmodified and EDTA-modified maize cob. Maize cob was found to be an excellent adsorbent for the removal of these metal ions. The amount of metal ions adsorbed increased as the initial concentration increased. Also, EDTA - modification enhanced the adsorption capacity of maize cob probably due to the chelating ability of EDTA. Among the three adsorption isotherm tested, Dubinin-Radushkevich gave the best fit with R² value ranging from 0.9539 to 0.9973 and an average value of 0.9819. This is followed by Freundlich isotherm (Ave. 0.9783) and then the Langmuir isotherm (Ave. 0.7637). The sorption process was found to be a physiosorption process as seen from the apparent energy of adsorption which ranged from 2.05KJ\mol to 4.56KJ\mol. Therefore, this study demonstrates that maize cob which is an environmental pollutant could be used to adsorb heavy metals and achieve cleanliness thereby abating environmental nuisance caused by the maize cob.

Determinação de biureto em uréia agroindustrial por espectrofotometria

Foi desenvolvido um método espectrofotométrico para a determinação de biureto em fertilizantes à base de uréia empregando Cu(OH)2(s) como reagente analítico. O método se baseia na reação entre biureto e Cu(OH)2(s) e formação do complexo Cu(C2N3O2H5)2 de coloração violeta cujo espectro apresenta máximo de absorção em 510 nm. Após o estabelecimento das melhores condições analíticas, o método proposto foi aplicado na determinação de biureto em duas amostras comerciais de uréia, uma para pecuária e outra para agricultura. Curvas analíticas construídas no intervalo de concentrações de 0,1 a 0,5% (m/v) em biureto produziram coeficientes de correlação típicos > 0,9990. Os resultados obtidos pelo método proposto foram concordantes ao nível de 95% de confiança com os obtidos por um método alternativo empregando espectrometria de absorção atômica. A exatidão do método foi também avaliada por meio de testes de adição e recuperação de padrão. Recuperações de 92 a 100% foram obtidas e o desvio padrão relativo calculado para 12 medidas sucessivas de uma amostra contendo 0,31% (m/v) foi 2%.

Caracterização das frações das substâncias húmicas de diferentes tamanhos moleculares

Neste trabalho realizou-se a extração das substâncias húmicas (SH) provenientes da turfa coletada às margens do rio Mogi-Guaçu, segundo metodologia descrita por Rosa et al., 2000. As SH foram fracionadas em um equipamento de ultrafiltração em três faixas de tamanhos moleculares 30 - 100 KDa, <30 KDa e >100 KDa. As frações foram caracterizadas por diferentes técnicas analíticas, infravermelho (IV), análise elementar, espectroscopia na região do ultravioleta/visível (UV/Vis) e ressonância paramagnética eletrônica (EPR). Verificou-se que as frações de menor tamanho molecular (30 - 100 KDa e <30 KDa) possuem um maior número de moléculas com oxigênio ligados, enquanto que a fração de maior tamanho molecular (>100 KDa) apresentou um maior número de moléculas aromáticas. Através dos resultados das análises elementares e de ressonância paramagnética eletrônica, constatou-se que a fração <30 KDa apresentou uma menor porcentagem de carbono, nitrogênio e hidrogênio e uma menor quantidade de radicais livres em relação as demais, indicando que esta fração possui um menor número de anéis aromáticos conjugados. Já nas análises por IV foram observadas bandas características das SH.

Spectrophotometric determination of lansoprazole in pharmaceuticals using bromate-bromide mixture based on redox and complexation reactions

Two sensitive spectrophotometric methods are described for the determination of lansoprazole (LPZ) in bulk drug and in capsule formulation. The methods are based on the oxidation of lansoprazole by insitu generated bromine followed by determination of unreacted bromine by two different reaction schemes. In one procedure (method A), the residual bromine is treated with excess of iron (II), and the resulting iron (III) is complexed with thiocyanate and measured at 470 nm. The second approach (method B) involves treating the unreacted bromine with a measured excess of iron (II) and remaining iron (II) is complexed with orthophenanthroline at a raised pH, and measured at 510 nm. In both methods, the amount of bromine reacted corresponds to the amount of LPZ. The experimental conditions were optimized. In method A, the absorbance is found to decrease linearly with the concentration of LPZ (r = -0.9986) where as in the method B a linear increase in absorbance occurs (r = 0.9986) The systems obey Beer's law for 0.5-4.0 and 0.5-6.0 µg mL-1 for method A and method B, respectively. The calculated molar absorptivity values are 3.97µ10(4) and 3.07µ10(4) L mol-1cm-1 for method A and method B, respectively, and the corresponding Sandell sensitivity values are 0.0039 and 0.0013 µg cm-2. The limit of detection (LOD) and quantification (LOQ) are also reported for both methods. Intra-day and inter-day precision, and accuracy of the methods were established as per the current ICH guidelines. The methods were successfully applied to the determination of LPZ in capsules and the results tallied well with the label claim and the results were statistically compared with those of a reference method by applying the Student's t-test and F-test. No interference was observed from the concomitant substances normally added to capsules. The accuracy and validity of the methods were further ascertained by performing recovery experiments via standard-addition method.

Does cotinine act upon reactive oxygen species and peroxidases?

Nicotine, an oxidizing agent, is certainly one of the most widely used alkaloids in the world. It is, together with its main metabolite, cotinine, responsible for tobacco-dependence. The use of tobacco is closely associated with lung disease, morphological leukocyte modification and generation of oxidant species. The aim of this study was to look for a possible relationship between cotinine, oxidant species generation and oxidative processes. After studying the action of cotinine in some chemical oxidation models and on the enzymatic kinetics of peroxidases (myeloperoxidase and horseradish peroxidase), we concluded that cotinine does not act directly upon H2O2, HOCl, taurine chloramines, horseradish peroxidase or myeloperoxidase.

Potentiometric and conductometric studies on the system acid-isopolytungstate and the formation of lanthanum tungstates

The stoichiometry of the polyanions formed by the action of nitric acid on sodium tungstate (< 0.01M) has been studied by means of electrometric techniques involving pH-potentiometric and conductometric titrations. The well defined inflections and breaks in the titration curves provide evidence for the existence of the polyanions, para-W12O41(10-) and meta-W12O39(6-) corresponding to the ratio of H+:WO4(2-) as 7:6 and 9:6 in the pH ranges 5.7-6.0 and 3.6-4.1, respectively. The interaction of lanthanum nitrate with sodium tungstate solutions, at specific pH levels 8.0, 5.9 and 4.0 was also studied by pH and conductometric titrations, in aqueous and alcoholic media, with each of the reagents alternatively used as titrant. The electrometric experiments provide definite evidence of the formation of normal-La2O3.3WO3, para-5La2O3.36WO3 and meta-La2O3.12WO3 tungstates in the vicinity of pH 6.3, 5.0 and 4.2, respectively. Analytical investigations on the precipitates formed confirm the results of the electrometric study.

Reatividade do [Fe(CO)2(eta2-CS2)(PPh 3)2] frente a compostos de Cu(I): síntese de espécies binucleares heterometálicas contendo CS2 em ponte entre Fe(0) e Cu(I)

Este trabalho contempla a síntese e caracterização espectroscópica de dois compostos carbonílicos heterometálicos do tipo [Fe(CO)3(m-CS2)(PPh3 )(CuX)], X = Cl, ClO4. Os dados provenientes da espectroscopia no infravermelho e de RMN de 31P{¹H} foram conclusivos quanto à proposição da geometria octaédrica distorcida ao redor do átomo de ferro (0), como também sobre a natureza bimetálica de ambos compostos. Estes dados esclareceram o modo de coordenação dos grupos carbonilos, da trifenilfosfina (PPh3), bem como a disposição do ligante dissulfeto de carbono em ponte entre os átomos de Fe (0) e Cu (I).

Use of modified silica gel for concentrating Pb (II) and Cd (II) occurring in form of complex anions

The performance of silica gel, modified by the impregnation with a high molecular weight quaternary amine (triethyl octadecyl ammonium iodide), used for the concentration of heavy metals occurring in water is studied. The material under study captures Cd, Pb, which are capable of forming stable complexes with I- ions.The results obtained about the metal capture, under dynamic conditions, are described and metal ions are removed by desorption with EDTA and quantified by AAS.

Synthesis, characterization and thermal studies on solid state 3-methoxybenzoate of lighter trivalent lanthanides

Solid-state Ln -3-MeO-Bz compounds, where Ln stands for lighter trivalent lanthanides (La Sm) and 3-methoxybenzoate, have been synthesized. Thermogravimetry (TG), differential scanning calorimetry (DSC), X-ray powder diffractometry, infrared spectroscopy, and complexometry were used to characterize and to study the thermal behaviour of these compounds. The results led to information concerning the composition, dehydration, polymorphic transformation, thermal behaviour and thermal decomposition of the synthesized compounds.

Crystal structures of 5-chloro-2-methoxybenzoates of Mn(II), Co(II), Ni(II) and Zn(II)

The crystal and molecular structures of [bis(5-chloro-2-methoxybenzoate)tetraaquamanganese(II)], [pentaaqua(5-chloro-2-methoxybenzoato)cobalt(II)] (5-chloro-2-methoxybenzoate), [pentaaqua(5-chloro-2-methoxybenzoato)nickel(II)] (5-chloro-2-methoxybenzoate) and [aquabis(5-chloro-2-methoxybenzoate)zinc(II)] monohydrate were determined by a single-crystal X-ray analysis. Mn(H2O)4L2 (where L = C8H6ClO3) crystallizes in the monoclinic system, space group P21/c. [Co(H2O)5L]L and [Ni(H2O)5L]L both are isostructural, space group P212121. The crystals of [Zn(H2O)L2] H2O are monoclinic, space group Pc. Mn(II) ion is positioned at the crystallographic symmetry center. Mn(II) and Co(II) ions adopt the distorted octahedral coordination but Zn(II) tetrahedral one.The carboxylate groups in the complexes with M(II) cations function as monodentate, bidentate and/or free COO-groups. The ligands exist in the crystals as aquaanions. The complexes of 5-chloro-2-methoxybenzoates with Mn(II), Co(II) and Zn(II) form bilayer structure.

Evaluation of a carbon paste electrode modified with organofunctionalised SBA-15 silica in the determination of copper

The performance of a carbon paste electrode (CPE) modified with SBA-15 nanostructured silica organofunctionalised with 2-benzothiazolethiol for determination of Cu(II) ions in sugar cane spirit (cachaça) is described, based on differential pulse anodic stripping voltammetry (DPASV) procedure. The Cu(II) oxidation peak was observed at 0.03 V (vs. SCE) in phosphate solution (pH 3.0). The results were obtained using optimised conditions such as 100 mV pulse amplitude, 3 min accumulation time, 25 mV s-1 scan rate in phosphate solution pH 3.0, resulting in a linear dynamic range from 8.0 x 10-7 to 1.0 x 10-5 mol L-1 Cu(II) and a limit of detection 2.0 x10-7 mol L-1. Cu(II) spiked in a cachaça sample was determined with 102.5 % mean recovery at mmol L-1 level. Interference from other metallic cations present in the sample was avoided by the standard addition procedure.

Efeito do íon malato no processo de oxidação do ácido ascórbico por oxigênio molecular catalisado por íons cobre(II)

Íons cobre(II) catalisam a oxidação de ácido ascórbico por oxigênio molecular. O mecanismo envolve a coordenação dos reagentes ao íon metálico. Íons malato, quando presentes, também se coordenam ao cobre(II) e inibem o efeito catalítico. As constantes cinéticas específicas (k / mol-1 L min.-1) da reação em presença de íons malato são 46,58, 7,11 e 30,00 em valores de pH de 3,5, 4,5 e 5,8, respectivamente. Existe decréscimo do valor de k com o aumento do pH de 3,5 para 4,5, o que está de acordo com a coordenação mais efetiva do malato ao cobre(II).