Obtenção de placas cerâmico a partir de formulações de massas triaxiais de resíduos de caulim, chamote de telha e cinza vegetal

The production of red ceramic is an industrial activity that causes an intense impact. The manufacture of its products considerably increases the demand for natural resources, mainly with the extraction of raw material. The ceramic material produced generates waste, such as ash firewood and chamote. The residue from the beneficiation of kaolin is deposited in a poor, degrades the environment and contaminate water sources and soil, constituting in this manner, ecological disasters. The main objective of this work is to develop the formulation of a ceramic product consisting solely of industrial solid wastes, from ceramic tiles, (chamote) residue of kaolin and ash firewood. It is assumed that this product made in the laboratory can be used in coatings, wall and floor. The aim is to facilitate the replacement of the raw material of original composition of a ceramic body, for waste, while the process of production equal to the conventionally used, so that the properties of the product are reproduced. This work is characterized waste as its chemical composition, analysis of particle size, X-ray diffraction and thermal behavior. Several formulations were studied. The mass of waste was prepared by dry process, pressed to 25 MPa, and then burned in muffle type oven to 850, 950, 1050 and 1150 °C. The results showed that it is technically possible to produce porous tiles only with waste. It was found that the formulations of bodies play a key role in the properties of the final product, as well as the sintering temperature and heating rates. RN in the waste of kaolin is estimated at 15,000 t/month, about 3,000 gray t/month and chamote with 10 million pieces/month damaged. The presence of carbonates of calcium and magnesium at 1050 ° C results in an appropriate porosity and mechanical strength. The formulation M3JE, composed of 69% waste of kaolin, 7.7% and 23.3% of chamote of gray, became suitable for porous materials with the strength and absorption within the level of national and international standards

Estudo térmico e de materiais na construção de casas populares com blocos confeccionados a partir de um composto a base de cimento, gesso, eps e raspa de pneu

We built an experimental house on an UFRN´s land using blocks made by a composite consisting of cement, plaster, EPS, crushed rubber and sand. Several blocks were made from various compositions and we made preliminary tests of mechanical and thermal resistance, choosing the most appropriate proportion. PET bottles were used inside the block to provide thermal resistance. In this work, a second function was given to the bottles: to serve as a docking between the blocks, because the ends of the cylinders came out of each block on top as well as at the bottom, with the bottom cut, allowing to fit of the extremities of the upper cylinder of a block in the lower holes of the other one, which were formed by the cutting already mentioned. Minimum compression tests were performed according to ABNT standards for walls closing blocks (fence). With that house built, we did studies of thermal performance in order to ascertain conditions of comfort, checking external and internal temperatures in the walls and in the ambient, among other variables, such as wind speed and relative humidity. The resulting blocks provided adequate thermal insulation to the environment, where the walls presented differences up to 11.7 ºC between the outer and inner faces, getting the maximum temperature inside the house around 31 °C, within the so-called thermal comfort zone for warm climates. At the end of the experiments it was evident the effectiveness of that construction in order to provide thermal comfort in the internal environment of the house, as well as we could confirm the viability of building houses from recyclable materials, reducing the constructive costs, becoming a suitable alternative for low- incoming families. Moreover, besides the low cost, the proposal represents an alternative use of various recyclable materials, therefore considered an ecological solution

Caracterização do cultivar de bananeira 'figo-cinza' em dois ciclos de produção

O presente trabalho teve como objetivo avaliar as características de crescimento, produção e caracterizar alguns atributos de qualidade dos frutos do cultivar de bananeira-Figo-Cinza em dois ciclos de produção, nos anos de 2009 e 2010. Foram avaliadas características de crescimento, tais como altura da planta, circunferência do pseudocaule, número de folhas ativas, número de perfilhos e número de dias entre o florescimento e a colheita. Estas medidas foram feitas na emissão da inflorescência. Foram mensuradas também as características de produção, como peso do cacho, número de frutos, número de pencas, número, comprimento e diâmetro dos frutos da 2ª penca. em relação à qualidade dos frutos, foram analisados os atributos físicos e químicos: textura; pH; acidez titulável e sólidos solúveis. O delineamento adotado foi o inteiramente casualisado, com dois tratamentos (ciclos), cinco repetições e duas plantas úteis por parcela experimental. Foi utilizado o teste de Tukey (P< 0,05) para a comparação entre as médias. em geral, as características de crescimento e produção foram maiores no segundo ciclo, apresentando 134 dias do florescimento à colheita, circunferência do pseudocaule de 64,20 cm, altura de planta igual a 3,82 m e peso de cacho de 11,83 kg. Os atributos de qualidade não variaram entre os ciclos, exceto a textura, que foi maior no segundo ciclo, com valores médios de 993,31 gfcm-2.

Alocação de biomassa e nutrientes em Myriophyllum aquaticum sob diferentes níveis de macronutrientes

O objetivo deste trabalho foi verificar o efeito de diferentes concentrações de macronutrientes no crescimento e na alocação de biomassa seca em folha, caule e raiz de Myriophyllulm aquaticum. As plantas foram cultivadas em vasos plásticos preenchidos com areia lavada e emersas em solução nutritiva. O experimento foi conduzido em um delineamento inteiramente ao acaso, com quatro níveis (0, 25, 50 e 75%) da concentração original de N, P, K Ca, Mg e S da solução nutritiva, além de uma testemunha (100% da solução nutritiva), com quatro repetições e por um período de 38 dias. A maior produção de biomassa total foi obtida na testemunha. A ausência de K afetou a alocação de biomassa em raízes. Quanto ao comprimento total dos ramos, a maior resposta ocorreu entre os níveis de Ca a 60 mg L-1. A solução a 100% dos macronutrientes propiciou o maior comprimento das plantas. O número de ramos entre os níveis de N e P seguiu uma tendência linear e crescente com as concentrações desses nutrientes, porém em maior proporção para o fósforo. As condições mais favoráveis ao desenvolvimento das plantas ocorreram a 100% dos macronutrientes da solução base. Entre os níveis de nitrogênio verificaram-se maiores teores de N nas folhas do que nos caules. Já para os demais nutrientes a alocação desses recursos foi destinada em maior proporção para o caule. A maior alocação de biomassa nesta espécie destinou-se ao caule.

Teores de metais na biomassa de Egeria densa, Egeria najas e Ceratophyllum demersum

Este estudo foi realizado com o objetivo de se estimar o conteúdo de elementos metálicos presentes em três macrófitas aquáticas submersas, procurando avaliar a participação destas plantas na remoção destes elementos na água e criar base de dados que permita prever o impacto ambiental do descarte delas em solo ou na própria água. As amostras foram desidratadas, moídas e encaminhadas aos laboratórios para análise e quantificação dos elementos. Para as três espécies, a maior concentração de elementos foi observada durante o verão, ocorrendo declínio nas concentrações durante o inverno, principalmente para os elementos vanádio e chumbo. Não foi detectada presença do elemento mercúrio em nenhuma das amostras.

Liberação de CO2, biomassa microbiana e fósforo disponível em solo adicionado de matéria seca de poaia-branca

O presente experimento, inteiramente casualizado, foi desenvolvido em condições de laboratório no Departamento de Defesa Fitossanitária, FCA/UNESP - Botucatu, entre julho e setembro de 1992. Amostras de Areia Quartzosa equivalentes à 40 g de terra seca à 105 oC ± 2 com ou sem adição de 1,9 g de matéria seca de plantas de poaia-branca (Richardia brasiliensis), 0,19 g de nitrogênio (NH4)2SO4 e 0,88 g de apatita de Araxá, foram incubadas no escuro a 25 o C ± 2 , com umidade mantida a 60% da capacidade de retenção de água. Durante a incubação, determinou-se o CO2 liberado, utilizando-se o método de retenção em NAOH seguida de titulometria com HCl; a biomassa microbiana, método de fumigação-incubação; o pH e a quantidade de fósforo extraído por resina. A maior liberação de CO2 ocorreu durante os dez primeiros dias de incubação, com 77% do total de carbono liberado nos tratamentos com adição de poaia, e 37% nos tratamentos sem adição da mesma. A liberação de CO2 foi 57 vezes maior nos tratamentos com poaia em relação ao controle. A poaia também provocou aumentos na biomassa microbiana (média de 8 vezes a biomassa do tratamento controle), e a adição de nitrogênio e/ou fosfato de rocha junto à poaia antecipou os picos de formação de biomassa de 20 para 10 dias de incubação. Os níveis de fósforo disponível foram maiores no tratamento com adição de fosfato de rocha apenas. A poaia também alcalinizou o sistema, não permitindo desta forma, observar-se relação significativa entre pH e teor de fósforo disponível.

Estudo da influência da temperatura na degradação termoquímica da biomassa de avelós

The bio-oil obtained from the pyrolysis of biomass has appeared as inter-esting alternative to replace fossil fuels. The aim of this work is to evaluate the influence of temperature on the yield of products originating from the pyrolysis process of the powder obtained from the dried twigs of avelós (Euphorbia tirucalli), using a rotating cylinder reactor in laboratory scale. The biomass was treated and characterized by: CHNS, moisture, volatiles, fixed carbon and ashes, as well as evaluation of lignin, cellulose and hemicellulose, besides other instrumental techniques such as: FTIR, TG/DTG, DRX, FRX and MEV. The activation energy was evaluated in non-isothemichal mode with heating rates of 5 and 10 oC/min. The obtained results showed biomass as feedstock with potential for biofuel production, because presents a high organic matter content (78,3%) and fixed-carbon (7,11%). The activation energy required for the degradation of biomass ranged between 232,92 392,84 kJ/mol, in the temperature range studied and heating rate of 5 and 10°C/min. In the pyrolysis process, the influence of the reaction temperature was studied (350-520 ° C), keeping constant the other variables, such as, the flow rate of carrier gas, the centrifugal speed for the bio-oil condensationa, the biomass flow and the rotation of the reactor. The maximum yield of bio-oil was obtained in the temperature of 450°C. In this temperature, the results achieved where: content of bio-oil 8,12%; char 32,7%; non-condensed gas 35,4%; losts 23,8%; gross calorific value 3,43MJ/kg; pH 4,93 and viscosity 1,5cP. The chromatographic analysis of the bio-oil produced under these conditions shows mainly the presence of phenol (17,71%), methylciclopentenone (10,56%) and dimethylciclopentenone (7,76%)

Estudo da influência da temperatura na degradação termoquímica da biomassa de avelós (euphorbia tirucalli Linn)

The bio-oil obtained from the pyrolysis of biomass has appeared as inter-esting alternative to replace fossil fuels. The aim of this work is to evaluate the influence of temperature on the yield of products originating from the pyrolysis process of the powder obtained from the dried twigs of avelós (Euphorbia tirucalli), using a rotating cylinder reactor in laboratory scale. The biomass was treated and characterized by: CHNS, moisture, volatiles, fixed carbon and ashes, as well as evaluation of lignin, cellulose and hemicellulose, besides other instrumental techniques such as: FTIR, TG/DTG, DRX, FRX and MEV. The activation energy was evaluated in non-isothemichal mode with heating rates of 5 and 10 oC/min. The obtained results showed biomass as feedstock with potential for biofuel production, because presents a high organic matter content (78,3%) and fixed-carbon (7,11%). The activation energy required for the degradation of biomass ranged between 232,92 392,84 kJ/mol, in the temperature range studied and heating rate of 5 and 10°C/min. In the pyrolysis process, the influence of the reaction temperature was studied (350-520 ° C), keeping constant the other variables, such as, the flow rate of carrier gas, the centrifugal speed for the bio-oil condensationa, the biomass flow and the rotation of the reactor. The maximum yield of bio-oil was obtained in the temperature of 450°C. In this temperature, the results achieved where: content of bio-oil 8,12%; char 32,7%; non-condensed gas 35,4%; losts 23,8%; gross calorific value 3,43MJ/kg; pH 4,93 and viscosity 1,5cP. The chromatographic analysis of the bio-oil produced under these conditions shows mainly the presence of phenol (17,71%), methylciclopentenone (10,56%) and dimethylciclopentenone (7,76%)

Levantamento e avaliação de critérios para a ampliação de escala da produção de biossurfactantes utilizando melaço como substrato

Biosurfactants are amphiphilic molecules synthesized by microorganisms such as bacteria, yeast or filamented fungi cultivated in various carbon sources among sucrose and hydrocarbons. These molecules are composed by a hydrophilic and hydrophobic part. They operate mostly at interfaces of fluids of different polarities. Because of this characteristic, they are potentially employed in numerous industries, such as the textile, medical, cosmetics, food and mainly in the petrochemical ones. Therefore industry has interest in developing new biosurfactant production processes in high scale, in order to become them economically competitive when compared to synthetic biosurfactants. This work aims to evaluate the biosurfactant production applying a non-conventional substrate sugar cane molasses proceeding from the sugar industry thus reducing the production costs. The strain identified as AP029/GLIIA, isolated from oil wells in Rio Grande do Norte state and used in these experiments belongs to the culture collection of Antibiotics Department of UFPE. The fermentation were carried out using different conditions according to a factorial planning 24 with duplicate at center point, in which the studied factors were molasse concentration, nitrate concentration, agitation and aeration ratio. The experiments were performed in a shaker at 38ºC of temperature. Samples were withdrawn in regular periods of time of up to 72 hours of fermentation in order to analyze substrate consumption, cellular concentration, superficial tension, critical micelle dilution (CMD-1 e CMD-2) as well as extracelullar protein production. The results showed a production of 3,480 g/L of biomass, a reduction of 41% on superficial tension, 67% of substrate consumption and 0,2805 g/L of extracellular protein

Ondaletas e movimento browniano fracionário: aplicação à caracterização de poços de petróleo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Eficácia do cimento de ionômero de vidro como selante oclusal sobre a paralisação de lesões cariosas em dentina

Dental caries consists in a multifactorial and dynamic process. The knowledge of the ionic interactions among dental tissues and dental biofilm make possible its understanding as a process that can be stopped. Recently, the use of sealants have lost its function as preventive agent and passed to be argued as a possible therapeutical agent. This happens by hindering the substratum flow to the lesion inner and, therefore, controls the advance of the process. This study aimed to evaluate glass ionomer cement as a not invasive technique of treatment in occlusal caries without clinical cavitation, but with dentinal involvement. The research was accomplished using a controlled clinical trial with two groups (experimental and control) in 38 subjects (8-18 years) with 51 molars. The teeth of the experimental group were sealed with glass ionomer cement (Vidrion-R, S.S.White, Juiz de Fora, Brazil) and the molars control did not suffer intervention. The experimental group was followed by a year and the control by 8 months due the progression of the carious injury. Both groups were reevaluated to each 4 months with the use of clinical, radiographic and laser fluorescence (DIAGNOdent®) examination. The analysis of the clinical evaluation did not observe a significant difference between experimental and control groups. However, analysis with radiographic and laser fluorescence (DIAGNOdent®) examination observed a significant difference (p> 0,05) between groups, demonstrating a wors condition to the group without intervention. The results suggest that glass ionomer cement as sealant can be efficient to paralyze dentinal caries without clinical cavitation

Ecologia alimentar do boto cinza, sotalia guianensis (van banédén, 1864), no litoral do rio grande do norte (rn)

This study investigated factors that influence the group size during the behavior foraging of estuarine dolphin Sotalia guianensis in the coast south of the state Rio Grande do Norte (RN), it also characterized the diet of estuarine dolphins and elaborated an otoliths catalog for aid in the identification of the preys found in the stomach contents. In relation to the group size during behaviour foraging, inside of the Curral Bay, larger frequency of solitary hunt was observed. Factors as tide variation, group composition and seasons didn't present correlation with the number of animals observed during a feeding episode. Capture success for participant was shown significantly larger when the animals hunted alone, what possibly explains the largest frequency of solitary hunt inside of the Curral Bay. About diet, were identified 18 bone fishes species, with predominance of species the families Haemulidae and Sciaenidae and five cephalopods species, including two new species in the diet of Sotalia guianensis in Brazil. Our results indicated that estuarine dolphin in the coast oriental from Rio Grande do Norte (RN) feeds predominantly of fish that form shoal, of habitat estuarino and producing of sounds. The analysis of the images, otoliths of 43 species of coastal fish of the coast of the state of Rio Grande do Norte (RN), aided by the offered descriptions, demonstrated to be an effective methodology for the knowledge of those structures, as well as it represented a form of reducing the subjectivity in the identification of the bone fishes found in stomach content

Boto cinza (Sotalia guianensis, Van Benédén, 1864) (Cetacea, Delphinidae): Atividade aérea, forrageio e interações inter-específicas, na Praia de Pipa (Tibau do Sul RN) e estudo comparativo entre duas populações do Nordeste do Brasil

Sotalia guianensis is a small cetacean of the Delphinidae family, with coastal habits and whose area of distribution ranges from Florianópolis (27º35'S, 48º34'W), in Brazil, to Honduras (15º58'N, 85º42'W). At Pipa beach, on the south coast of RN state, in Brazil, the species occur throughout the year. The present study was carried out in two bays, which are bordered by cliffs. The animals were monitored from vantage points, using the "Ad libitum" and "all the occurrences" methods; during the years of 1999 and 2004. The study was divided in 4 chapters: Behavioral standards of two populations of gray dolphin, (Sotalia guianensis, Van Benédén, 1864) in the northeast of Brazil; Aerial activity of the gray dolphin: its possible function and the influence of environmental and behavioral factors; The influence of daily and monthly variation of the tides, of the period of the day and group size on the gray dolphin forage activity; kleptoparasitism interactions of frigatebird (Fregata magnificens, Mattheus, 1914) during the gray dolphin forage activity. The results have shown that the gray dolphin has a varied and complex behavioral repertoire. The leap is the most frequent behavior; the aerial activity is diffuse during daylight and is influenced by some factors, such as the level of the tide and social factors. The gray dolphin, when in the bay, most frequently feeds isolate or in small groups. The forage is diffuse during daylight; however, being more frequent in the morning and is influenced by the daily and monthly variation of the tide. At Pipa beach, kleptoparasitarian interactions were registered between the gray dolphin and the frigatebird (Fregata magnificens). The frigatebird forage strategy consists basically of two ways: to fly over great extensions searching for dead fish and to steal food (kleptoparasitism). These interactions were predominantly carried out between immature and female adult birds and adult and immature dolphins, and occurred during daylight. The present study can be considered an initial landmark to a better knowledge on the gray dolphin surface behavior, especially regarding the aerial behavioral repertoire and forage strategy of this species. However, it is necessary to continue these studies, so that we can understand better the complex social life of these animals and thus create effective measures for its conservation