Análise fisico-química e legalidade em bebidas de laranja

The aim of this paper was to measure the total soluble solids content (°Brix), titrable total acidity (AT) and ratio in orange beverages, such as frozen concentrated juice, not from concentrate juice, nectar and soft drink and to compare them with their Quality and Identity Standards (PIQ) published by the Ministry of Agriculture, Livestock and Food Supply (MAPA) and Codex Alimentarius. Four orange frozen concentrated juices, twenty two juices, seven nectars and thirteen orange soft drinks were analyzed. All frozen concentrated orange juices were in agreement with Codex Alimentarius. The majority of not from concentrated orange juices and soft drinks was in accord to Brazilian legislation. The orange nectars could not be compared with the standards because they are not published by MAPA or Codex Alimentarius.

Composição físico-química e propriedades tecnológicas da farinha de folhas de mandioca

Cassava leaves can be considered an important nutritional source when compared to other commonly consumed vegetables leaves. Cassava leaves have high levels of protein, fiber and minerals, and arestill underexplored due to the lack of information regarding the use of them as afood product, as well as, their use as an industrial raw material. The consumption of cassava leaves in fresh form is impractical due to the presence of cyanide, thereby it is required a pretreatment to be performed to reduce this component. The objective of this study was to produce and characterize the four made with cassava leaves as its chemical composition, color, indices of absorption and water solubility, and pasting properties, aiming to provide information of interest for possible application as an ingredient in the food industry. Cassava leaf flour showed low moisture content (6.6 %)and significant amounts of fiber (30.68 %), protein (23.00 %), and total carbohydrate (22.27%). Drying and milling processes allowed to obtain a flour with a low content of total cyanide (0.3 mg 100g-1 ), and the presence of vitamin C (56.6 mg 100g-1 ) and β –carotene (38 mg 100g- 1 ). The color analysis of cassava leaf flour showed low lightness with, predominantly, green and yellow pigments. The cassava leaf flour presented good solubility (14.85 %) and water absorption (6.87 g gel. g-1 ). Pasting properties showed a low peak of viscosity and a higher final viscosity with a retrogradation tendency, indicating a low capacity of this flour to form gel. The flour of cassava leaves can be a good source of nutrition when used as a food ingredient in soups and pasta. However, it is not indicated to products that require high gel formation.

Análise termoeconômica e eficiência ecológica de uma termoelétrica com absorção química de CO2

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeitos da ingestão de simbiótico e indol-3-carbinol sobre o processo de carcinogênese química de cólon em ratos Wistar alimentados com dieta contendo heme

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Identificação taxonômica e análise conexionista de bactérias heterotróficas e fatores abióticos de ambientes lóticos sob influência de efluentes do refino no petróleo

This study used a multi-analytical approach based on traditional microbiological methods for cultivation and isolation of heterotrophic bacteria in the laboratory associated with the molecular identification of the isolates and physicochemical analysis of environmental samples. The model chosen for data integration was supported by knowledge from computational neuroscience, and composed by three modules: (i) microbiological parameters, contemplating taxonomic data obtained from the partial sequencing of the 16S rRNA gene from 80 colonies of heterotrophic bacteria isolated by plating method in PCA media. For bacterial colonies isolation were used water samples from Atibaia and Jaguarí rivers collected at the site of water captation for use in effluent treatment, upstream from the entrance of treated effluent from the Paulínia refinery (REPLAN/Petrobras) located in the Paulínia-SP municipality, from the output of the biological treatment plant with stabilization pond and from the raw refinery wastewater; (ii) chemical parameters, ending measures of dissolved oxygen (DO), chemical oxygen demand (COD), biochemical oxygen demand (BOD), chloride, acidity CaCO3, alkalinity, ammonia, nitrite, nitrate, dissolved ions, sulfides, oils and greases; and (iii) physical parameters, comprising the pH determination, conductivity, temperature, transparency, settleable solids, suspended and soluble solids, volatile material, remaining fixing material (RFM), apparent color and turbidity. The results revealed interesting theoretical relationships involving two families of bacteria (Carnobacteriaceae and Aeromonadaceae). Carnobacteriaceae revealed positive theoretical relationships with COD, BOD, nitrate, chloride, temperature, conductivity and apparent color and negative theoretical relationships with the OD. Positive theoretical relationships were shown between Aeromonadaceae and OD and nitrate, while this bacterial family showed negative theoretical...

Análise do perfil de dureza e microestrutura de um aço forjado AISI A2 submetido a tratamento térmico com resfriamento em água

Due to the large use of steel in several processes around the world, there is the increasingly concern to find new materials and/or optimization and improvement of the processes, as the need to reduce the cost and a productivity increase in the primary industry, such as the siderurgy. The rolling is the most used mechanical process in the world and therefore is required the development of new tools in high volume and with optimum characteristics to support the market demand. Forged rolls used are for rolling. These rolls have heat treatment that has the purpose to achieve the appropriated mechanical properties to support the variables of the rolling process. The objective of this work is to analyze the hardness profile and the microstructure a tool steel similar to AISI A2, forged in an opened die process and submitted to heat treatment with water-cooling. The results allowed plotting a hardness profile and performing a microstructure analysis, and whereby to confirm that the heat treatment is not a quenching, but it is a material beneficiation by the hardening of superficial layer, since there is no martensitic microstructure. Therefore, this paper provides the support to future studies about the possibility to perform enhancements in this thermal heat made in the rolls produced at Gerdau Plant in Pindamonhangaba

Estudo da qualidade da gasolina tipo A e sua composição química empregando análise de componentes principais

The type A gasoline samples were analyzed by gas chromatography with flame ionization detector (GC-FID) which allowed quantifying and classifying of the various compounds into different classes of hydrocarbons. Several physicochemical parameters were evaluated according to the official methods in order to compare the results obtained against the limits established by the Agência Nacional de Petróleo, Gás Natural e Biocombustíveis (ANP, 2011). Additionally, principal component analysis (PCA) was applied to discriminate the samples studied, which revealed the separation of four groups according to their chemical composition determined in samples collected from the eight fuel distributors in the State of Pará.

Identificação taxonômica e análise conexionista de bactérias heterotróficas e fatores abióticos de ambientes lóticos sob influência de efluentes do refino no petróleo

This study used a multi-analytical approach based on traditional microbiological methods for cultivation and isolation of heterotrophic bacteria in the laboratory associated with the molecular identification of the isolates and physicochemical analysis of environmental samples. The model chosen for data integration was supported by knowledge from computational neuroscience, and composed by three modules: (i) microbiological parameters, contemplating taxonomic data obtained from the partial sequencing of the 16S rRNA gene from 80 colonies of heterotrophic bacteria isolated by plating method in PCA media. For bacterial colonies isolation were used water samples from Atibaia and Jaguarí rivers collected at the site of water captation for use in effluent treatment, upstream from the entrance of treated effluent from the Paulínia refinery (REPLAN/Petrobras) located in the Paulínia-SP municipality, from the output of the biological treatment plant with stabilization pond and from the raw refinery wastewater; (ii) chemical parameters, ending measures of dissolved oxygen (DO), chemical oxygen demand (COD), biochemical oxygen demand (BOD), chloride, acidity CaCO3, alkalinity, ammonia, nitrite, nitrate, dissolved ions, sulfides, oils and greases; and (iii) physical parameters, comprising the pH determination, conductivity, temperature, transparency, settleable solids, suspended and soluble solids, volatile material, remaining fixing material (RFM), apparent color and turbidity. The results revealed interesting theoretical relationships involving two families of bacteria (Carnobacteriaceae and Aeromonadaceae). Carnobacteriaceae revealed positive theoretical relationships with COD, BOD, nitrate, chloride, temperature, conductivity and apparent color and negative theoretical relationships with the OD. Positive theoretical relationships were shown between Aeromonadaceae and OD and nitrate, while this bacterial family showed negative theoretical...

Análise do perfil de dureza e microestrutura de um aço forjado AISI A2 submetido a tratamento térmico com resfriamento em água

Due to the large use of steel in several processes around the world, there is the increasingly concern to find new materials and/or optimization and improvement of the processes, as the need to reduce the cost and a productivity increase in the primary industry, such as the siderurgy. The rolling is the most used mechanical process in the world and therefore is required the development of new tools in high volume and with optimum characteristics to support the market demand. Forged rolls used are for rolling. These rolls have heat treatment that has the purpose to achieve the appropriated mechanical properties to support the variables of the rolling process. The objective of this work is to analyze the hardness profile and the microstructure a tool steel similar to AISI A2, forged in an opened die process and submitted to heat treatment with water-cooling. The results allowed plotting a hardness profile and performing a microstructure analysis, and whereby to confirm that the heat treatment is not a quenching, but it is a material beneficiation by the hardening of superficial layer, since there is no martensitic microstructure. Therefore, this paper provides the support to future studies about the possibility to perform enhancements in this thermal heat made in the rolls produced at Gerdau Plant in Pindamonhangaba

Fatores químicos e físicos que afetam a contaminação por chumbo e cobre em água potável: uma abordagem para o estudo de caso em química analítica

Lead and copper concentrations in drinking water increase considerably on going from municipality reservoirs to the households sampled in Ribeirão Preto (SP-Brazil). Flushing of only 3 liters of water reduced metal concentrations by more than 50%. Relatively small changes in water pH rapidly affected corrosion processes in lead pipes, while water hardness appeared to have a long-term effect. This approach aims to encourage University teachers to use its content as a case study in disciplines of Instrumental Analytical Chemistry and consequently increase knowledge about drinking water contamination in locations where no public monitoring of trace metals is in place.

Variação espacial e temporal da trama trófica bentônica de um ambiente costeiro à plataforma continental adjacente no Atlântico Sudoeste: análise de isótopos estáveis

A análise das razões de isótopos estáveis de carbono (δ13C) e nitrogênio (δ15N) vem sendo utilizada para identificar as fontes primárias de carbono dos ecossistemas e traçar as interações tróficas entre seus componentes. Nesse contexto, a variabilidade espacial e temporal da trama trófica bentônica da Baía de Santos e da plataforma continental interna e média, ao largo da costa sul do estado de São Paulo, Brasil (23,9-24,5°S), foi investigada durante o inverno de 2005 e o verão de 2006. A matéria orgânica particulada em suspensão (MOPS), zooplâncton, macroalgas, vegetais terrestres (C3), sedimento e 21 categorias de consumidores bentônicos foram analisados. Segundo os valores de δ13C, a MOPS foi a principal fonte primária de matéria orgânica. A análise de regressão entre os valores médios de δ15N e δ13C indicou, no inverno, semelhanças nas assinaturas isotópicas dos consumidores bentônicos entre a plataforma interna e média e diferenças entre essas e as da baía. Por outro lado, no verão, foram observadas diferenças nessas assinaturas entre a baía, a plataforma interna e a média. Os valores de 13C dos consumidores decresceram do ambiente costeiro em direção à plataforma média, enquanto os de 15N aumentaram. Em relação ao δ13C, houve diferença da MOPS, possivelmente pela contribuição de produção primária nova (PPN) ou do microfitobentos no verão. Quanto ao δ15N, o enriquecimento da mesma categoria trófica no gradiente ambiental pode ser devido às diferenças na MOPS, resultante da PPN na plataforma interna no verão, decorrente da entrada da Água Central do Atlântico Sul (ACAS), que enriquece a água oligotrófica nessa área

Estudio sobre la durabilidad de los nuevos tipos de cemento para la evaluación del comportamiento de morteros y hormigones frente a la agresión química de los sulfatos y del agua de mar

Esta investigación ha sido desarrollada para analizar la influencia de las características específicas de los nuevos cementos en el comportamiento expansivo originado durante cinco años por el ataque externo por sulfatos o agua de mar, y para estudiar la validez de diversos métodos de ensayo aplicables para evaluar la resistencia de los conglomerantes a los sulfatos o al agua de mar. Se han determinado las características químicas y mecánicas de los quince cementos seleccionados en el estudio (su contenido de yeso, tipo y cantidad de adiciones, contenidos de C3A y C4AF) para examinar la relación entre estos parámetros y su durabilidad frente al ataque por sulfatos. Se han llevado a cabo ensayos para evaluar la resistencia a sulfatos sobre probetas de mortero fabricadas con los quince cementos comunes seleccionados de muy distintos tipos, la mayoría de ellos resistentes a sulfatos conforme a la norma UNE-EN 197-1. Por cada tipo de cemento se fabricaron probetas de mortero para la realización de ensayos acelerados usando Na2SO4 como medio agresivo según la norma ASTM C 1012 manteniendo esas condiciones de exposición durante dos años. En paralelo se fabricaron otras series de probetas idénticas, que fueron conservadas en agua de mar y en agua saturada en cal (como patrón de un medio no agresivo) durante el mismo plazo. Adicionalmente estos cementos fueron evaluados conforme a los procedimientos de ensayo acelerado de la norma ASTM C 452 y del ensayo de Koch y Steinegger. También se fabricaron otras series de probetas de 40x40x160 mm (adoptando una relación a/c=0,5 y la composición arena:cemento definida en la norma UNE-EN 196-1). Durante cinco años de exposición en las tres condiciones de conservación establecidas (sulfatos, agua de mar y agua patrón) se han efectuado ensayos para determinar la resistencia a compresión y el deterioro superficial de las probetas de mortero. Ninguno de los conglomerantes fue mezclado inicialmente con yeso para acelerar el ataque ni se establecieron otras condiciones no realísticas en la fabricación de los morteros Se ha analizado el comportamiento durable de los cementos tanto frente al ataque por sulfatos como por agua de mar. Para la evaluación se han tomado en consideración las variaciones de contenido en C3A, los tipos y proporciones de los constituyentes (adiciones puzolánicas, escorias de horno alto, caliza …) con el mismo tipo de clínker en algunos casos. Se ha procedido a evaluar la validez de los límites de aceptación establecidos en cada uno de los ensayos acelerados para determinar la resistencia a sulfatos y valorar su idoneidad en los nuevos cementos, y se ha propuesto un método de ensayo acelerado recomendable para discriminar cementos resistentes y no resistentes a sulfatos. A la edad final de los tres tipos de exposición han sido correlacionados los parámetros relativos a la degradación superficial, pérdida de resistencia y expansión lineal de las probetas con las características de los cementos y los productos expansivos analizados mediante difracción de rayos X, con objeto de poder redefinir las características recomendables exigibles a los cementos resistentes a sulfatos o al agua de mar. Experimental research has been performed to relate specific cement characteristics to expansion due to sulfate or sea water attack during five years, and to study different test methods suitability for sulfate and marine resistance. Chemical and mechanical characteristics were studied to determine the variation in properties of selected cements (SO3 content, type and amount of additions, C3A, and C4AF content) and examine relationships between these characteristics and the results of sulfate resistance. Sulfate resistance testing have been performed on mortar specimens prepared from fifteen cement types of statistically diverse chemical composition, most of them with sulfate resistant properties according to European standard EN 197-1 Mortar specimens testing using Na2SO4 as the aggressive medium according to ASTM C 1012 was performed using each cement; identical specimens were also stored in sea water, and in lime saturated water (blank condition), up to two years age. Additionally these cements were tested conforming to ASTM C 452 and Koch and Steinegger test. Mortar specimens of 40x40x160 mm were also moulded (with w/c ratio and cement:sand composition of EN 196-1). Compressive strength of these mortar specimens have been tested during five years of immersion in a sulfate solution and also in seawater (and in lime saturated water, as a blank condition), and external damage and have been analyzed. None of the prepared mortars was blended with gypsum or any other nonrealistic condition. Durability behaviour in sulfate resistant common cements conforming to EN 197-1 exposed to sulfate attack was evaluated, and also the correlation between sulfate resistance and seawater resistance has been studied. Different C3A contents, variable types and proportioning of constituents (limestone, pozzolanic additions, blastfurnace slag ...) with or without the same clinker type were investigated. Recommended acceptance limits for sulfate resistance of cements concerning to each used test method were evaluated in order to explore their suitability. A new accelerated method has been recommended to provide a meaningful discrimination between sulfate resistant or non-sulfate resistant cements. Relationships between cement characteristics, degradation, expansive products obtained by X-ray diffraction techniques, strength loss and maximum expansion after applied storage treatments, were correlated at final age, to redefine cement characteristics for sulfate resistant and marine resistant Portland cement.

O DISCURSO AMBIENTAL JORNALÍSTICO, POLÍTICO E EMPRESARIAL EM ÂMBITO LOCAL: uma proposta de análise

Esta tese tem como tema principal o discurso ambiental local. Trata-se de uma proposta de análise, que pode ser aplicada a este tipo de discurso em qualquer localidade, e um estudo de caso, que aplicou a análise proposta na tese. O objetivo geral desta pesquisa foi analisar a informação local sobre meio ambiente veiculada por meio dos discursos jornalístico, político e empresarial, estabelecendo relações históricas, sociais e ideológicas do discurso ambiental que permeiam as três áreas em questão. A metodologia incluiu três fases: pesquisa bibliográfica e revisão de literatura sobre os principais conceitos levantados no trabalho; levantamento de discursos locais disponíveis na mídia para análise no estudo de caso; análise dos discursos a partir de protocolo elaborado com base na Análise do Discurso de linha francesa. O estudo de caso traz a análise do discurso ambiental no município de Frutal-MG, onde hoje estão em andamento várias pesquisas e projetos na área ambiental. A principal conclusão do trabalho confirma a hipótese da pesquisa de que a informação ambiental fruto dos discursos político, jornalístico e empresarial em âmbito local tem caráter predominantemente situacional, mercadológico e propagandístico, pouco focada em conscientizar e educar e com ênfase em interesses comerciais e eleitorais e na resolução de problemas emergenciais.