Asymptotic Recovery for Discrete-Time Systems

An asymptotic recovery design procedure is proposed for square, discrete-time, linear, time-invariant multivariable systems, which allows a state-feedback design to be approximately recovered by a dynamic output feedback scheme. Both the case of negligible processing time (compared to the sampling interval) and of significant processing time are discussed. In the former case, it is possible to obtain perfect. © 1985 IEEE.

Physical soil characteristics of waterlogged and saline lands of five districts of Haryana, India

Physical characteristics of waterlogged and saline soils of five districts, namely Rohtak, Faridabad, Gurgaon, Sonipat and Jhajjar, of Haryana were studied to evaluate the aquaculture potential. The soil samples from 76 sites were procured and analysed for pH, electrical conductivity, soil particles and water retention capacity, since the knowledge of these parameters is essential for the preliminary evaluation of a site for aqua-farming. Six soil types were identified and clay-loam was observed to be the maximum at 45 (59.21%) sites, followed by silty-clay loam at 14 (18.42%), sandy-clay loam at six (7.89%), silty-loam at four (5.26%), sandy-loam at four (5.26%) and loam at three (3.94%) sites. The pH of soil indicated moderate to high alkaline conditions ranging between 8.01and 9.00 at 53 (69.73%) sites, 9.01 and 10.00 at 17 (22.36%) sites, and low between 7.01 and 8.00 at six (7.89%) sites. The electrical conductivity was found to range between <1 and 10 mmho cmˉ¹ with the value of <1.0 mmho cmˉ¹ at 36 (47.36%) sites. The water retention capacity was observed mostly to be moderate. The paper describes the interrelationship between these parameters with reference to the suitability for aqua-farming.

Experimental and theoretical comparison between static and dynamic torsional soil tests

The dynamic properties of dry Leighton Buzzard sand have been investigated using a resonant column test apparatus. These data are compared with very low frequency cyclic tests on identical specimens of sand. The comparison indicates that the properties of dry sand are independent of frequency. A simple one-dimensional model of kinematic hardening plasticity is used to predict the dynamic behaviour of the sand. The input parameters for this model are based on the results of static tests. These may be conducted on standard laboratory equipment with only minor modifications. The predictions are in good agreement with the measured data.

Bias-dependent recovery time of all-optical resonant nonlinearity in InGaAsP/InGaAsP MQW waveguide

We have investigated a resonant refractive nonlinearity in a semiconductor waveguide by measuring intensity dependent phase shifts and bias-dependent recovery times. The measurements were performed on an optimized 750-μm-long AR coated buried heterostructure MQW p-i-n waveguide with a bandedge at 1.48 μm. Figure 1 shows the experimental arrangement. The mode-locked color center laser was tuned to 50 meV beyond the bandedge and 8 ps pulses with peak incident power up to 57 W were coupled into the waveguide. Some residual bandtail absorption remains at this wavelength and this is sufficient to cause carriers to be photogenerated and these give rise to a refractive nonlinearity, predominantly by plasma and bandfilling effects. A Fabry-Perot interferometer is used to measure the spectrum of the light which exits the waveguide. The nonlinearity within the guide causes self phase modulation (SPM) of the light and a study of the spectrum allows information to be recovered on the magnitude and recovery time of the nonlinear phase shift with a reasonable degree of accuracy. SPM spectra were recorded for a variety of pulse energies coupled into he unbiased waveguide. Figure 2 shows the resultant phase shift measured from the SPM spectra as a function of pulse energy. The relationship is a linear one, indicating that no saturation of the nonlinearity occurs for coupled pulse energies up to 230 pJ. A π phase shift, the minimum necessary for an all-optical switch, is obtained for a coupled pulse energy of 57 pJ while the maximum phase shift, 4 π, was measured for 230 pJ. The SPM spectra were highly asymmetric with pulse energy shifted to higher frequencies. Such spectra are characteristic of a slow, negative nonlinearity. This relatively slow speed is expected for the unbiased guide as the recovery time will be of the order of the recombination time of the photogenerated electrons, about 1 ns for InGaAsP material. In order to reduce the recovery time of the nonlinearity, it is necessary to remove the photogenerated carriers from the waveguide by a process other than recombination. One such technique is to apply a reverse bias to the waveguide in order to sweep the carriers out. Figure 3 shows the effect on the recovery time of the nonlinearity of applying reverse bias to the waveguide for 230 pJ coupled power. The recovery time was reduced from one much longer than the length of the pulse, estimated to be about 1 ns, at zero bias to 18 ± 3 ps for a bias voltage greater than -4 V. This compares with a value of 24 ps obtained in a bulk waveguide.

The modelling of soil plasticity

The modeling of the soil plasticity was discussed and it was shown that the grain breakage is an important factor of the plastic soil behaviour. A reduction of internal coefficient of friction was observed when stress-level was increased. The yield paths of all stress path tests determined by curve fitting were presented.

Soil conditioning under London

The CTRL Contract 220 covered 7.5km twin-bore tunnels excavated between late 2002 and early 2004 from Stratford Box to St Pancras station in Central London. To ensure efficient machine operation as well as the transport and disposal of soil, soil conditioning treatments were applied. Specifically, the foam injection ratio (FIR) and the polymer injection ratio (PIR) (injected volume of foam and polymer solution expressed as a percentage of the excavated soil volume) were employed. It was found that carefully selected soil conditioning allowed chamber pressures of 200kPa or more to be accurately controlled in the stiff London Clay and to an extent, in the very stiff clays of the Lambeth Group. Average FIRs of 50% and PIRs of 7 and 9% were used in the Thanet Sand and in the Lambeth Group Clays. In contrast, much lower quantities of foam were used in the London Clay.

Dem analysis of soil-pipeline interaction in sand under lateral and upward movements at deep embedment

The soil-pipeline interactions under lateral and upward pipe movements in sand are investigated using DEM analysis. The simulations are performed for both medium and dense sand conditions at different embedment ratios of up to 60. The comparison of peak dimensionless forces from the DEM and earlier FEM analyses shows that, for medium sand, both methods show similar peak dimensionless forces. For dense sand, the DEM analysis gives more gradual transition of shallow to deep failure mechanisms than the FEM analysis and the peak dimensionless forces at very deep depth are higher in the DEM analysis than in the FEM analysis. Comparison of the deformation mechanism suggests that this is due to the differences in soil movements around the pipe associated with its particulate nature. The DEM analysis provides supplementary data of the soil-pipeline interaction in sand at deep embedment condition.

Modelling effects of axial load on behaviour of pile groups in laterally-spreading soil

Previous research into the behaviour of piled foundations in laterally-spreading soil deposits has concentrated on pile groups that carry small or negligible axial loads. This paper presents dynamic centrifuge test results for 2 x 2 pile groups with bending and geometric properties similar to real 0.5 m diameter tubular steel and solid circular reinforced-concrete field piles. Axial loads applied represented upper-bounds on typical working loads. The simultaneous scaling of the relevant properties controlling both lateral and axial behaviour allows comparisons to be drawn regarding the particular mechanisms of failure that would dominate for each type of pile. Flexible reinforced-concrete piles which tend to carry lower loads were found to be dominated by lateral effects, while steel piles, which are much stiffer and usually carry greater loads are dominated by settlement considerations. © 2006 Taylor & Francis Group.

Mussel recovery and species dynamics at four California rocky intertidal sites: 1992 data report

This is an interim report for a study of mussel recovery and species dynamics at four California rocky intertidal sites. Conducted by Kinnetic Laboratories, Inc. (KLI), and funded by the Minerals Management Service (MMS), the initial experimental field study began in spring 1985 and continued through spring 1991. The initial field study included six sites along the central and northern California coast. In 1992, MMS decided to continue the work started by KLI through an in-house study and establishment of the MMS Intertidal (MINT) team. Four of the original six sites have been continued by MMS. The study methods of the original study have been retained by the MINT team, and close coordination with the original KLI team continues. In 1994, the MMS Environmental Studies Program officially awarded a contract to the MINT team for this in-house study. This interim report presents the results from the fall 1992 sampling, the first year of sampling by the MINT team. The report presents a limited statistical analysis and visual comparison of the 1992 data. The next interim report will include data collected during fall 1994 and will present a broader statistical analysis of both the 1992 and 1994 data sets.