Estudio de la utilización de las cenizas de cenicero de centrales termoeléctricas de carbón como adición del cemento portland : análisis comparativo con las cenizas volantes

El empleo de nuevas adiciones en el cemento se plantea como una vía para que éste sea un material más sostenible. En este contexto, las cenizas de fondo o cenicero de las centrales termoeléctricas de carbón actualmente se están llevando a vertederos creando un problema medioambiental o se están empleando con usos minoritarios. Sin embargo, la presente Tesis doctoral demuestra cómo este material puede ser empleado como un componente principal de los cementos portland mezclado en una proporción optimizada con las cenizas volantes o solo. Por tanto, este estudio se puede considerar como un trabajo prenormativo que cubre las demandas de la sociedad tanto económicas como ambientales. Se han estudiado las propiedades químicas, físicas y mecánicas de las cenizas de fondo o cenicero de las centrales termoeléctricas de carbón como una adición potencial de los cementos portland (con adiciones) en comparación con los cementos portland con cenizas volantes. En consecuencia, el objeto de la presente Tesis Doctoral es el análisis de las prestaciones de morteros elaborados con clínkeres de cemento portland y cenizas de fondo o cenicero con cenizas volantes de las centrales termoeléctricas de carbón en unos porcentajes similares a los correspondientes a los CEM II/A-V, CEM II/B-V y CEM IV/A (V) de la UNE-EN 197-1:2011. La caracterización de las cenizas de fondo o cenicero y de las cenizas volantes de las centrales termoeléctricas de carbón se ha realizado mediante las técnicas analíticas de FRX, ICP, análisis químicos, DRX, densidad, granulometría láser, superficie específica Blaine, ATD, TG, puzolanicidad, MEB y EDX; mientras que la caracterización de las mezclas se ha realizado mediante análisis químico (análisis químico, FRX e ICP y), DRX, MIP, granulometría láser, puzolanicidad, MEB y EDX, agua de consistencia normal, inicio y final de fraguado, estabilidad de volumen, colorimetría, calor de hidratación, DTA y TG, asícomo ensayos de resistencia; resistencia a flexión y compresión y ensayos de durabilidad (carbonatación natural, resistencia al hielo-deshielo, resistencia a la acción de los sulfatos y resistencia a la reacción árido-álcali). Finalmente, se han comprobado las propiedades de las cenizas de cenicero y cenizas volantes en hormigones, realizando ensayos de resistencia a compresión y resistividad. Los resultados obtenidos indican que la sustitución parcial o completa de las cenizas volantes por las de cenicero no tiene un efecto tecnológicamente importante en las propiedades ni mecánicas ni durables, incluso los mejora en determinados aspectos. Por tanto, se recomienda la normalización de las cenizas de fondo o cenicero de las centrales termoeléctricas de carbón como componente principal de los cementos portland comunes de la UNE-EN 197-1:2011. Actualmente, la mayoría de las cenizas de fondo se consideran como un residuo que no tiene un posible uso. Sólo se han encontrado algunos datos relativos a la aplicación de este material combinado con cenizas volantes como un componente principal de los cementos portland. Por tanto, la realización de un estudio integrado considerando aspectos que van desde la caracterización de las cenizas hasta las mezclas de conglomerante y la hidratación de éstas, desarrollo de resistencias y demás prestaciones y durabilidad (carbonatación natural, resistencia al hielo-deshielo, resistencia a la acción de los sulfatos y resistencia a la reacción árido-álcali), así como los ensayos de resistencia en hormigón es totalmente novedoso. Como resultado final se propone incorporar estas nuevas adiciones en aplicaciones particulares y en la norma más apropiada para ello. Los resultados han demostrado que la sustitución completa o parcial de las cenizas volantes por cenizas de fondo o cenicero de las centrales termoeléctricas de carbón en cementos de los tipos CEM II/A-V, CEM II/B-V y CEM IV/A no afecta de forma significativa en la resistencia a compresión a 1, 3 ,7, 28 ni 90 días ni a la durabilidad. En parte esto se debe a que la composición química de ambas cenizas es muy similar en la mayoría de los elementos tales como Fe2O3, TiO2, P2O5, SrO2, aunque en algún caso, como en el ZnO, se encuentra alguna ligera diferencia. Por tanto, se pueden esperar unas ligeras diferencias en el mecanismo de hidratación de las diferentes mezclas estudiadas. La presencia de los óxidos mencionados afectará a la composición de la fase acuosa y, en consecuencia, podrían ser elementos lixiviables. Asimismo, influyen de distinta manera en propiedades tales como los tiempos de fraguado y en la durabilidad. New additions to the cement are needed to achieve a more sustainable construction material. Within this context, bottom ashes produced in coal-fired power stations are currently wastes which are dumped provoking an environmental problem. Only in few cases are being used in minor applications. However, the present PhD Thesis shows how this material can be used as a main constituent of Portland cement when it is mixed in an optimised proportion with fly ashes or added to the Portland clinker alone. Therefore, this study may also be considered as a pre-standardization work which covers both the environmental and economic demands of society. Chemical, physical and mechanical characteristics of pulverized coal combustion bottom ash used as a potential constituent of Portland cements (with additions) are studied in comparison to Portland cements with fly ashes. Therefore, the aim of this experimental PhD Thesis is the analysis of the performance of mortars made of clinker of Portland cement and bottom and/or fly ashes in similar proportions to those of CEM II/A-V, CEM II/B-V and CEM IV/A (V) according to EN 197-1:2011. Characterisation of bottom and fly ashes has been done by XRF, ICP, chemical analyses, XRD, density, laser granulometry, Blaine, ATD, TG, pozzolanity, SEM and EDS. Characterisation of bottom and fly ashes mixes has been perform by chemical analyses, XRF, ICP, XRD, MIP, laser granulometry, pozzolanity, SEM, EDS, setting time, soundness, colorimetric test, heat of hydration, ATD, TG, compressive strength, and durability tests (natural carbonation, frost-thaw resistance, sulphate resistance and silica-alkali resistance). In conclusion, it can be established that partial or complete replacement of fly ash by bottom ash has neither significant effect on mechanical nor durability properties. Even, they are improved in several aspects. Therefore, it is recommended to standardise the bottom ash as a main cement constituent of the European standard EN 197-1:2011. Nowadays, most bottom ashes are considered as waste without any potential re-use. Only a few papers deal with the study of this material and its use mixed with fly ashes to be employed as a main constituent of Portland cement. Therefore, the execution of an integrated study considering together aspects from the initial characterization of the ashes and blinder mixes to the hydration steps, strength achievement, leading behaviour and durability (natural carbonation, sulphate attack, aggregate-alcali reaction and freeze-thaw resistance) is totally new. As result, it is proposed to include this new addition for particular applications in the appropriate cement standard. The results have shown that with regard to the compressive strength at 1, 3, 7, 28 and 90 days, partial or complete replacement of fly ash by bottom ash in CEM II/A-V, CEM II/B-V and CEM IV/A has no more significant effects. Partially, this can be explained because the bottom ash contains a similar amount of most of the elements, Fe2O3, TiO2, P2O5, SrO2, and so on, instead of ZnO. Therefore, slight hydration differences are expected. The presence of such oxides might have a significant effect on pore solution concentration and so will be leachable constituents. They will also play an important role in the cement properties such as setting times and durability.

Thermal and mechanical properties of recycled poly(Lactic acid)

Biodegradable polymers have experienced increased attention in recent years because of their wide range of applications in biomedical, packaging and agriculture fields. PLA, poly(lactic acid), is a linear aliphatic biodegradable thermoplastic polyester, with good mechanical properties, thermal stability, processability and low environmental impact, widely used as an alternative to conventional polymers. PLA products can be recycled after use either by remelting and reprocessing the material, or by hydrolysis to basic lactic acid [1]. The object of this communication is the study of the possible variation in physical properties induced by sub sequent reprocessing cycles of PLA.

Amelioration of a degraded acid soil from SW Spain by no-tillage and Ca-amendment

En los suelos, el exceso de acidez lleva asociado deficiencias en ciertos nutrientes y una alta disponibilidad de aluminio, tóxico para los cultivos propios del ambiente mediterráneo. Su laboreo, provoca la pérdida de materia orgánica (MO), deteriora su estructura y reduce la actividad biológica, provocando en última instancia una menor calidad del suelo. Es de esperar pues que cuando se labran suelos ácidos, sus problemáticas particulares tiendan a agravarse. En nuestra zona de estudio, la “raña” de Cañamero (Extremadura, España), predominan los suelos muy ácidos y degradados por un laboreo inadecuado. Las rañas constituyen amplias plataformas casi horizontales, con unos suelos muy viejos (Palexerults), que se caracterizan por tener el complejo de cambio dominado por el aluminio, y un pH ácido que decrece en profundidad. Poseen un potente horizonte Bt rico en arcillas caoliníticas, que propicia que en periodos con exceso de lluvia, se generen capas colgadas de agua cercanas a la superficie. En torno a los años 1940’s estos suelos, que previamente sostenían un alcornocal, o su matorral de sustitución, se pusieron en cultivo. El laboreo aceleró la mineralización de la materia orgánica, agravó los problemas derivados del exceso de acidez y condujo al abandono de los campos cultivados por falta de productividad. Para recuperar la calidad de estos suelos degradados y obtener unos rendimientos compatibles con su uso agrícola es necesario, por un lado, aplicar enmiendas que eleven el pH y reduzcan la toxicidad del aluminio y, por otro, favorecer el incremento en el contenido en MO. En 2005 se implantó en esta raña un ensayo de campo para estudiar la influencia del no laboreo y de la utilización de una enmienda cálcica en parámetros relacionados con la calidad del suelo en un cultivo forrajero. El diseño experimental fue en parcelas divididas con cuatro repeticiones donde el factor principal fue el tipo de laboreo, no laboreo (NL) frente a laboreo convencional (LC), y el factor secundario el uso o no de una enmienda cálcica. La enmienda consistió básicamente en una mezcla de espuma de azucarería y yeso rojo y se incorporó al comienzo del ensayo hasta los 7 cm de profundidad. Desde el comienzo del ensayo el NL influyó positivamente en el contenido de carbono orgánico total (COT) y particulado (COP), mientras que la enmienda tuvo una ligera influencia al principio del ensayo en ambos pero su efecto positivo se desvaneció con el paso del tiempo. Los mayores contenidos en COT y POC se observaron cuando se combinó el NL con la enmienda. La enmienda incrementó con rapidez el pH, y el Ca, y disminuyó el contenido en aluminio hasta una profundidad de 50 cm, incluso en NL, y mejoró ligeramente la agregación del suelo. El NL por sí solo, gracias al aumento en POC, TOC y las proteínas del suelo relacionadas con la glomalina (PSRG), que son capaces de formar compuestos estables no tóxicos con el aluminio, también contribuyó a la reducción de la toxicidad de aluminio en la capa más superficial. Cuando en las campañas con exceso de precipitaciones se generaron capas colgadas de agua próximas a la superficie, el NL generó unas condiciones más favorables para la germinación y desarrollo del cultivo, resultando en una producción más alta que el LC. A ello contribuyó la mayor capacidad de almacenamiento de agua y la mayor transmisividad de esta hacia abajo, en la capa más superficial (0-5 cm) que propició una menor saturación por agua que el LC. Respecto a los parámetros relacionados con la agregación, el NL aumentó los macroagregados hasta los 10 cm de profundidad y favoreció la acumulación de CO y N en todas las fracciones de tamaño de agregados. Sin embargo, la recuperación del grado de macroagregación tras el cese del laboreo resulta lenta en comparación con otros suelos, posiblemente debido al bajo contenido en arcilla en el horizonte Ap. En comparación con el NL, la enmienda mostró también un efecto positivo, aunque muy ligero, en la agregación del suelo. En contradicción con otros estudios en suelos ácidos, nuestros resultados indican la existencia de una jerarquía de agregados, y destacan el papel importante de la MO en la mejora de la agregación. Tanto el NL como la enmienda favorecieron por separado varias propiedades químicas, físicas y biológicas del suelo, pero, en general, encontramos los mayores beneficios con su uso combinado. Además, a largo plazo el efecto positivo de NL en las propiedades del suelo fue en aumento, mientras que el efecto beneficioso de la enmienda se limitó básicamente a las propiedades químicas y se desvaneció en pocos años. Destacamos que las condiciones meteorológicas a lo largo del ensayo beneficiaron la producción de biomasa en NL, y en consecuencia las propiedades relacionadas con la materia orgánica, por lo que son un factor a tener en cuenta a la hora de evaluar los efectos de la enmienda y el laboreo sobre las propiedades del suelo, especialmente en zonas donde esas condiciones son muy variables entre una campaña y otra. Los resultados de este estudio han puesto de manifiesto que el NL no ha mermado la eficacia de la enmienda caliza, posiblemente gracias a la alta solubilidad de la enmienda aplicada, es más, el manejo con NL y enmienda es el que ha favorecido en mayor medida ciertos parámetros de calidad del suelo. Por el contrario el LC sí parece anular los beneficios de la enmienda en relación con las propiedades relacionadas con la MO. Por tanto, cabe concluir que la combinación de NL y la enmienda es una práctica adecuada para mejorar las propiedades químicas y físicas de suelos ácidos degradados por el laboreo. ABSTRACT Excessive acidity in soils is associated with deficiencies in certain nutrients and high concentrations of available aluminum, which is toxic for most Mediterranean crops. Tilling these soils results in the loss of soil organic matter (SOM), damages soil structure and reduces biological activity, ultimately degrading soil quality. It is expected, therefore, that when acid soils are tilled, their particular problems will tend to get worse. In our study area, the "Cañamero’s Raña” (Extremadura, Spain), acid soils degraded by an inappropriate tillage prevail. Rañas are large and flat platforms with very old soils (Palexerults), which are characterized by an exchange complex dominated by aluminum and an acid pH which decreases with depth. These soils have a strong Bt horizon rich in kaolinite clays, which encourages the formation of perched water-tables near the soil surface during periods of excessive rain. During the first third of the 20th century, these soils, that previously supported cork oak or its scrub replacement, were cultivated. Tillage accelerated the mineralization of the SOM, aggravating the problems of excessive acidity, which finally led to the abandonment of the land due to low productivity. To recover the quality of these degraded soils and to obtain consistent yields it is necessary, first, to apply amendments to raise the pH and reduce aluminum toxicity, and second to encourage the accumulation of SOM. In 2005 a field trial was established in the Raña to study the influence of no-tillage and the use of a Ca-amendment on soil quality related parameters in a forage crop agrosystem. The experimental design was a split-plot with four replicates where the main factor was tillage type, no-tillage (NT) versus traditional tillage (TT) and the secondary factor was the use or not of a Ca-amendment. The Ca-amendment was a mixture of sugar foam and red gypsum that was incorporated into the top 7 cm of the soil. Since the beginning of the experiment, NT had a positive influence on total and particulate organic carbon (TOC and POC, respectively), while the Ca-amendment had a small positive influence at the beginning of the study but its effect diminished with time. The highest TOC and POC contents were observed when NT and the Ca-amendment were combined. The Ca-amendment, even under NT, rapidly increased pH and Ca, and decreased the aluminum content to a depth of 50 cm, as well as improving soil aggregation slightly. NT, due to the increased POC, TOC and Glomalin-related soil proteins (GRSP), which can form stable non-toxic compounds with aluminum, also contributed to the reduction of aluminum toxicity in the upper layer. When perched water-tables near the soil surface were formed in campaigns with excessive rainfall, NT provided more favorable conditions for germination and crop development, resulting in higher yields compared with TT. This was directly related to the higher water storage capacity and the greater transmissivity of the water downwards from the upper layers, which led to lower water saturation under NT compared with TT. With regards to the aggregation-related parameters, NT increased macroaggregation to a depth of 10 cm and favored the accumulation of OC and N in all aggregate size fractions. However, the degree of recovery of macroaggregation after tillage ceased was slow compared with other soils, possibly due to the low clay content in the Ap horizon. Compared with NT, the Ca-amendment had a slight positive effect on soil aggregation. In contrast to other studies in acid soils, our results indicate the existence of an aggregate hierarchy, and highlight the important role of SOM in improving aggregation. Both NT and the Ca-amendment separately favored various chemical, physical and biological soil properties, but in general we found the greatest benefits when the two treatments were combined. In addition, the positive effect of NT on soil properties increased with time, while the beneficial effect of the Ca-amendment, which was limited to the chemical properties, vanished after a few years. It is important to note that the meteorological conditions throughout the experiment benefited biomass production under NT and, as a consequence, organic matter related properties. This suggests that meteorological conditions are a factor to consider when evaluating the effects of Ca-amendments and tillage on soil properties, especially in areas where such conditions vary significantly from one campaign to another. The results of this study show that NT did not diminish the effectiveness of the Ca-amendment, possibly due to the high solubility of the selected amendment. Moreover, the combination of NT and the Ca-amendment was actually the management that favored certain soil quality parameters the most. By contrast, TT seemed to nullify the benefits of the Ca-amendment with regards to the OM related properties. In conclusion, the combination of NT and the application of a Ca-amendment is an advisable practice for improving the chemical and physical properties of acid soils degraded by tillage.

Soil aggregate geometry: Measurements and morphology

Aggregates provide physical microenvironments for microorganisms, the vital actors of soil systems, and thus play a major role as both, an arena and a product of soil carbon stabilization and dynamics. The surface of an aggregate is what enables exchange of the materials and air and water fluxes between aggregate exterior and interior regions. We made use of 3D images from X-ray CT of aggregates and mathematical morphology to provide an exhaustive quantitative description of soil aggregate morphology that includes both intra-aggregate pore space structure and aggregate surface features. First, the evolution of Minkowski functionals (i.e. volume, boundary surface, curvature and connectivity) for successive dilations of the solid part of aggregates was investigated to quantify its 3D geometrical features. Second, the inner pore space was considered as the object of interest. We devised procedures (a) to define the ends of the accessible pores that are connected to the aggregate surface and (b) to separate accessible and inaccessible porosity. Geometrical Minkowski functionals of the intra-aggregate pore space provide the exhaustive characterization of the inner structure of the aggregates. Aggregates collected from two different soil treatments were analyzed to explore the utility of these morphological tools in capturing the impact on their morphology of two different soil managements, i.e. conventional tillage management, and native succession vegetation treatment. The quantitative tools of mathematical morphology distinguished differences in patterns of aggregate structure associated to the different soil managements.

Aggregate community properties and the strength of species’ interactions

Although humanity depends on the continued, aggregate functioning of natural ecosystems, few studies have explored the impact of community structure on the stability of aggregate community properties. Here we derive the stability of the aggregate property of community biomass as a function of species’ competition coefficients for a two-species model. The model predicts that the stability of community biomass is relatively independent of the magnitude of the interaction strengths. Instead, the degree of asymmetry of the interactions appears to be key to community stability.

Replacement of the proximal heme thiolate ligand in chloroperoxidase with a histidine residue

Chloroperoxidase is a versatile heme enzyme which can cross over the catalytic boundaries of other oxidative hemoproteins and perform multiple functions. Chloroperoxidase, in addition to catalyzing classical peroxidative reactions, also acts as a P450 cytochrome and a potent catalase. The multiple functions of chloroperoxidase must be derived from its unique active site structure. Chloroperoxidase possesses a proximal cysteine thiolate heme iron ligand analogous to the P450 cytochromes; however, unlike the P450 enzymes, chloroperoxidase possesses a very polar environment distal to its heme prosthetic group and contains a glutamic acid residue in close proximity to the heme iron. The presence of a thiolate ligand in chloroperoxidase has long been thought to play an essential role in its chlorination and epoxidation activities; however, the research reported in this paper proves that hypothesis to be invalid. To explore the role of Cys-29, the amino acid residue supplying the thiolate ligand in chloroperoxidase, Cys-29 has been replaced with a histidine residue. Mutant clones of the chloroperoxidase genome have been expressed in a Caldariomyces fumago expression system by using gene replacement rather than gene insertion technology. C. fumago produces wild-type chloroperoxidase, thus requiring gene replacement of the wild type by the mutant gene. To the best of our knowledge, this is the first time that gene replacement has been reported for this type of fungus. The recombinant histidine mutants retain most of their chlorination, peroxidation, epoxidation, and catalase activities. These results downplay the importance of a thiolate ligand in chloroperoxidase and suggest that the distal environment of the heme active site plays the major role in maintaining the diverse activities of this enzyme.

Multipotent neural precursors can differentiate toward replacement of neurons undergoing targeted apoptotic degeneration in adult mouse neocortex

Neurons undergoing targeted photolytic cell death degenerate by apoptosis. Clonal, multipotent neural precursor cells were transplanted into regions of adult mouse neocortex undergoing selective degeneration of layer II/III pyramidal neurons via targeted photolysis. These precursors integrated into the regions of selective neuronal death; 15 ± 7% differentiated into neurons with many characteristics of the degenerated pyramidal neurons. They extended axons and dendrites and established afferent synaptic contacts. In intact and kainic acid-lesioned control adult neocortex, transplanted precursors differentiated exclusively into glia. These results suggest that the microenvironmental alterations produced by this synchronous apoptotic neuronal degeneration in adult neocortex induced multipotent neural precursors to undergo neuronal differentiation which ordinarily occurs only during embryonic corticogenesis. Studying the effects of this defined microenvironmental perturbation on the differentiation of clonal neural precursors may facilitate identification of factors involved in commitment and differentiation during normal development. Because photolytic degeneration simulates some mechanisms underlying apoptotic neurodegenerative diseases, these results also suggest the possibility of neural precursor transplantation as a potential cell replacement or molecular support therapy for some diseases of neocortex, even in the adult.

Gene replacement by homologous recombination in the multicellular green alga Volvox carteri

With only two different cell types, the haploid green alga Volvox represents the simplest multicellular model system. To facilitate genetic investigations in this organism, the occurrence of homologous recombination events was investigated with the intent of developing methods for gene replacement and gene disruption. First, homologous recombination between two plasmids was demonstrated by using overlapping nonfunctional fragments of a recombinant arylsulfatase gene (tubulin promoter/arylsulfatase gene). After bombardment of Volvox reproductive cells with DNA-coated gold microprojectiles, transformants expressing arylsulfatase constitutively were recovered, indicating the presence of the machinery for homologous recombination in Volvox. Second, a well characterized loss-of-function mutation in the nuclear nitrate reductase gene (nitA) with a single G → A nucleotide exchange in a 5′-splice site was chosen as a target for gene replacement. Gene replacement by homologous recombination was observed with a reasonably high frequency only if the replacement vector containing parts of the functional nitrate reductase gene contained only a few nucleotide exchanges. The ratio of homologous to random integration events ranged between 1:10 and 1:50, i.e., homologous recombination occurs frequently enough in Volvox to apply the powerful tool of gene disruption for functional studies of novel genes.

Tyrosine replacement in P-selectin glycoprotein ligand-1 affects distinct kinetic and mechanical properties of bonds with P- and L-selectin

Selectins are adhesion molecules that initiate tethering and rolling of leukocytes on the vessel wall. Rolling requires rapid formation and breakage of selectin–ligand bonds that must have mechanical strength to resist premature dissociation by the forces applied in shear flow. P- and L-selectin bind to the N-terminal region of P-selectin glycoprotein ligand-1 (PSGL-1), a mucin on leukocytes. To define determinants on PSGL-1 that contribute to the kinetic and mechanical properties of bonds with selectins, we compared rolling of transfected preB cells expressing P- or L-selectin on transfected cell monolayers expressing wild-type PSGL-1 or PSGL-1 constructs with substitutions in targeted N-terminal residues. Rolling through P- or L-selectin required a Thr or Ser at a specific position on PSGL-1, the attachment site for an essential O-glycan, but required only one of three nearby Tyr residues, which are sites for Tyr-SO3 formation. The adhesive strengths and numbers of cells rolling through P- or L-selectin were similar on wild-type PSGL-1 and on each of the three PSGL-1 constructs containing only a single Tyr. However, the cells rolled more irregularly on the single-Tyr forms of PSGL-1. Analysis of the lifetimes of transient tethers on limiting densities of PSGL-1 revealed that L-selectin dissociated faster from single-Tyr than wild-type PSGL-1 at all shears examined. In sharp contrast, P-selectin dissociated faster from single-Tyr than wild-type PSGL-1 at higher shear but not at lower shear. Thus, tyrosine replacements in PSGL-1 affect distinct kinetic and mechanical properties of bonds with P- and L-selectin.

Chromosomal arm replacement generates a high level of intraspecific polymorphism in the terminal inverted repeats of the linear chromosomal DNA of Streptomyces ambofaciens

The chromosomal DNA of the bacteria Streptomyces ambofaciens DSM40697 is an 8-Mb linear molecule that ends in terminal inverted repeats (TIRs) of 210 kb. The sequences of the TIRs are highly variable between the different linear replicons of Streptomyces (plasmids or chromosomes). Two spontaneous mutant strains harboring TIRs of 480 and 850 kb were isolated. The TIR polymorphism seen is a result of the deletion of one chromosomal end and its replacement by 480 or 850 kb of sequence identical to the end of the undeleted chromosomal arm. Analysis of the wild-type sequences involved in these rearrangements revealed that a recombination event took place between the two copies of a duplicated DNA sequence. Each copy was mapped to one chromosomal arm, outside of the TIR, and encoded a putative alternative sigma factor. The two ORFs, designated hasR and hasL, were found to be 99% similar at the nucleotide level. The sequence of the chimeric regions generated by the recombination showed that the chromosomal structure of the mutant strains resulted from homologous recombination events between the two copies. We suggest that this mechanism of chromosomal arm replacement contributes to the rapid evolutionary diversification of the sequences of the TIR in Streptomyces.

Incremental lines of von Ebner in dinosaurs and the assessment of tooth replacement rates using growth line counts

Dinosaur dentine exhibits growth lines that are tens of micrometers in width. These laminations are homologous to incremental lines of von Ebner found in extant mammal and crocodilian teeth (i.e., those of amniotes). The lines likely reflect daily dentine formation, and they were used to infer tooth development and replacement rates. In general, dinosaur tooth formation rates negatively correlated with tooth size. Theropod tooth replacement rates negatively correlated with tooth size, which was due to limitations in the dentine formation rates of their odontoblasts. Derived ceratopsian and hadrosaurian dinosaurs retained relatively rapid tooth replacement rates through ontogeny. The evolution of dental batteries in hadrosaurs and ceratopsians can be explained by dentine formation constraints and rapid tooth wear. In combination with counts of shed dinosaur teeth, tooth replacement rate data can be used to assess population demographics of Mesozoic ecosystems. Finally, it is of historic importance to note that Richard Owen appears to have been the first to observe incremental lines of von Ebner in dinosaurs more than 150 years ago.

Identification of the proton pathway in bacterial reaction centers: Replacement of Asp-M17 and Asp-L210 with Asn reduces the proton transfer rate in the presence of Cd2+

The reaction center (RC) from Rhodobacter sphaeroides converts light into chemical energy through the reduction and protonation of a bound quinone molecule QB (the secondary quinone electron acceptor). We investigated the proton transfer pathway by measuring the proton-coupled electron transfer, kAB(2) [QA⨪QB⨪ + H+ → QA(QBH)−] in native and mutant RCs in the absence and presence of Cd2+. Previous work has shown that the binding of Cd2+ decreases kAB(2) in native RCs ≈100-fold. The preceding paper shows that bound Cd2+ binds to Asp-H124, His-H126, and His-H128. This region represents the entry point for protons. In this work we investigated the proton transfer pathway connecting the entry point with QB⨪ by searching for mutations that greatly affect kAB(2) (≳10-fold) in the presence of Cd2+, where kAB(2) is limited by the proton transfer rate (kH). Upon mutation of Asp-L210 or Asp-M17 to Asn, kH decreased from ≈60 s−1 to ≈7 s−1, which shows the important role that Asp-L210 and Asp-M17 play in the proton transfer chain. By comparing the rate of proton transfer in the mutants (kH ≈ 7 s−1) with that in native RCs in the absence of Cd2+ (kH ≥ 104 s−1), we conclude that alternate proton transfer pathways, which have been postulated, are at least 103-fold less effective.