Study of Control Methods of a High-Frequency Cycloconverter for Domestic Induction Heating Appliances

A high-frequency cyclonverter acts as a direct ac-to-ac power converter circuit that does not require a diode bidge rectifier. Bridgeless topology makes it possible to remove forward voltage drop losses that are present in a diode bridge. In addition, the on-state losses can be reduced to 1.5 times the on-state resistance of switches in half-bridge operation of the cycloconverter. A high-frequency cycloconverter is reviewed and the charging effect of the dc-capacitors in ``back-to-back'' or synchronous mode operation operation is analyzed. In addition, a control method is introduced for regulating dc-voltage of the ac-side capacitors in synchronous operation mode. The controller regulates the dc-capacitors and prevents switches from reaching overvoltage level. This can be accomplished by variating phase-shift between the upper and the lower gate signals. By adding phase-shift between the gate signal pairs, the charge stored in the energy storage capacitors can be discharged through the resonant load and substantially, the output resonant current amplitude can be improved. The above goals are analyzed and illustrated with simulation. Theory is supported with practical measurements where the proposed control method is implemented in an FPGA device and tested with a high-frequency cycloconverter using super-junction power MOSFETs as switching devices.

Entry Modes for Finnish Firms into the Zambian Renewable Energy Industry

The renewable energy industry in Zambia is poised for growth and offers many possibilities for Finnish firms willing to enter the market. The Zambian government’s deliberate policy measures aim at attracting foreign direct investment (FDI) into this sector. This study rationalises that this could be the pull factor for Finnish firms. The thesis gives an overview of the industry and investigates an appropriate mode of entry, basing its arguments on the comparison analysis of the two economies with the use of the world forum’s stages of economic development as a framework. The theoretical part of the study examines internationalisation theories, entry mode choice and factors influencing the choice. The multiple case study approach is implored, analysing four case companies from Finland with the use of extant literature on internationalisation relevant to the study. The research design involves the use of documentation, secondary data, interviews and observation. The results of the case analyses show that the Finnish firm’s most preferred entry mode initially is exporting because it is considered to be less risky. Additionally, the findings also reveal that the selection of a suitable mode of entry is dependent on the firms’ size, orientation and international experience and could therefore be considered to be subjective. Paramount is the act of gaining market knowledge. The study shows that only hydro-electrical, solar energies and biomass are by far the most used and known forms of renewable energy in Zambia, while other alternative sources still remain un-exploited thus highlighting a growth potential. However, policy formulation and the regulatory framework in the renewable energy sector were found to be wanting.

Heart rate variability under resting conditions in postmenopausal and young women

The aim of the present study was to compare the modulation of heart rate in a group of postmenopausal women to that of a group of young women under resting conditions on the basis of R-R interval variability. Ten healthy postmenopausal women (mean ± SD, 58.3 ± 6.8 years) and 10 healthy young women (mean ± SD, 21.6 ± 0.82 years) were submitted to a control resting electrocardiogram (ECG) in the supine and sitting positions over a period of 6 min. The ECG was obtained from a one-channel heart monitor at the CM5 lead and processed and stored using an analog to digital converter connected to a microcomputer. R-R intervals were calculated on a beat-to-beat basis from the ECG recording in real time using a signal-processing software. Heart rate variability (HRV) was expressed as standard deviation (RMSM) and mean square root (RMSSD). In the supine position, the postmenopausal group showed significantly lower (P<0.05) median values of RMSM (34.9) and RMSSD (22.32) than the young group (RMSM: 62.11 and RMSSD: 49.1). The same occurred in the sitting position (RMSM: 33.0 and RMSSD: 18.9 compared to RMSM: 57.6 and RMSSD: 42.8 for the young group). These results indicate a decrease in parasympathetic modulation in postmenopausal women compared to young women which was possibly due both to the influence of age and hormonal factors. Thus, time domain HRV proved to be a noninvasive and sensitive method for the identification of changes in autonomic modulation of the sinus node in postmenopausal women.

Novel virtual environment and real-time simulation based methods for improving life-cycle efficiency of non-road mobile machinery

Virtual environments and real-time simulators (VERS) are becoming more and more important tools in research and development (R&D) process of non-road mobile machinery (NRMM). The virtual prototyping techniques enable faster and more cost-efficient development of machines compared to use of real life prototypes. High energy efficiency has become an important topic in the world of NRMM because of environmental and economic demands. The objective of this thesis is to develop VERS based methods for research and development of NRMM. A process using VERS for assessing effects of human operators on the life-cycle efficiency of NRMM was developed. Human in the loop simulations are ran using an underground mining loader to study the developed process. The simulations were ran in the virtual environment of the Laboratory of Intelligent Machines of Lappeenranta University of Technology. A physically adequate real-time simulation model of NRMM was shown to be reliable and cost effective in testing of hardware components by the means of hardware-in-the-loop (HIL) simulations. A control interface connecting integrated electro-hydraulic energy converter (IEHEC) with virtual simulation model of log crane was developed. IEHEC consists of a hydraulic pump-motor and an integrated electrical permanent magnet synchronous motorgenerator. The results show that state of the art real-time NRMM simulators are capable to solve factors related to energy consumption and productivity of the NRMM. A significant variation between the test drivers is found. The results show that VERS can be used for assessing human effects on the life-cycle efficiency of NRMM. HIL simulation responses compared to that achieved with conventional simulation method demonstrate the advances and drawbacks of various possible interfaces between the simulator and hardware part of the system under study. Novel ideas for arranging the interface are successfully tested and compared with the more traditional one. The proposed process for assessing the effects of operators on the life-cycle efficiency will be applied for wider group of operators in the future. Driving styles of the operators can be analysed statistically from sufficient large result data. The statistical analysis can find the most life-cycle efficient driving style for the specific environment and machinery. The proposed control interface for HIL simulation need to be further studied. The robustness and the adaptation of the interface in different situations must be verified. The future work will also include studying the suitability of the IEHEC for different working machines using the proposed HIL simulation method.

Design of a Traction Motor With Tooth-Coil Windings and Embedded Magnets

Traction motor design significantly differs from industrial machine design. The starting point is the load cycle instead of the steady-state rated operation point. The speed of the motor varies from zero to very high speeds. At low speeds, heavy overloading is used for starting, and the field-weakening region also plays an important role. Finding a suitable fieldweakening point is one of the important design targets. At the lowest speeds, a high torque output is desired, and all current reserves of the supplying converter unit are used to achieve the torque. In this paper, a 110-kW 2.5-p.u. starting torque and a maximum 2.5-p.u. speed permanent-magnet traction motor will be studied. The field-weakening point is altered by varying the number of winding turns of machine. One design is selected for prototyping. Theoretical results are verified by measurements.

Computerized invasive measurement of time-dependent intraocular pressure

Several methods have been described to measure intraocular pressure (IOP) in clinical and research situations. However, the measurement of time varying IOP with high accuracy, mainly in situations that alter corneal properties, has not been reported until now. The present report describes a computerized system capable of recording the transitory variability of IOP, which is sufficiently sensitive to reliably measure ocular pulse peak-to-peak values. We also describe its characteristics and discuss its applicability to research and clinical studies. The device consists of a pressure transducer, a signal conditioning unit and an analog-to-digital converter coupled to a video acquisition board. A modified Cairns trabeculectomy was performed in 9 Oryctolagus cuniculus rabbits to obtain changes in IOP decay parameters and to evaluate the utility and sensitivity of the recording system. The device was effective for the study of kinetic parameters of IOP, such as decay pattern and ocular pulse waves due to cardiac and respiratory cycle rhythm. In addition, there was a significant increase of IOP versus time curve derivative when pre- and post-trabeculectomy recordings were compared. The present procedure excludes corneal thickness and error related to individual operator ability. Clinical complications due to saline infusion and pressure overload were not observed during biomicroscopic evaluation. Among the disadvantages of the procedure are the requirement of anesthesia and the use in acute recordings rather than chronic protocols. Finally, the method described may provide a reliable alternative for the study of ocular pressure dynamic alterations in man and may facilitate the investigation of the pathogenesis of glaucoma.

The Streptococcus mutans GlnR protein exhibits an increased affinity for the glnRA operon promoter when bound to GlnK

The control of nitrogen metabolism in pathogenic Gram-positive bacteria has been studied in a variety of species and is involved with the expression of virulence factors. To date, no data have been reported regarding nitrogen metabolism in the odontopathogenic species Streptococcus mutans. GlnR, which controls nitrogen assimilation in the related bacterial species, Bacillus subtilis, was assessed in S. mutans for its DNA and protein binding activity. Electrophoretic mobility shift assay of the S. mutans GlnR protein indicated that GlnR binds to promoter regions of the glnRA and amtB-glnK operons. Cross-linking and pull-down assays demonstrated that GlnR interacts with GlnK, a signal transduction protein that coordinates the regulation of nitrogen metabolism. Upon formation of this stable complex, GlnK enhances the affinity of GlnR for the glnRA operon promoter. These results support an involvement of GlnR in transcriptional regulation of nitrogen metabolism-related genes and indicate that GlnK relays information regarding ammonium availability to GlnR.

Interaction between human cytomegalovirus UL136 protein and ATP1B1 protein

Interplay between the host and human cytomegalovirus (HCMV) has a pivotal role in the outcome of infection. A region (referred to as UL/b’) present in the Toledo strain of HCMV and low passage clinical isolates contains 19 additional genes, which are absent in the highly passaged laboratory strain AD169. Products of the UL/b’ genes may determine the manifestations of HCMV infection in vivo. However, little is known about the host factors, which interact with UL/b’ proteins. This study was conducted to investigate the function of the HCMV UL136 protein. By yeast two-hybrid screening, the β1 subunit of the host Na+/K+-ATPase (ATP1B1) was identified to be a candidate protein, which interacts with the HCMV UL136 protein. The interaction was further evaluated both in vitro by pull-down assay and in vivo by immunofluorescent co-localization. The results showed that the UL136 protein can interact with ATP1B1 in vitro. Co-localization of UL136-EGFP and ATP1B1-DsRed in cell membranes suggests that ATP1B1 was a partner of the UL136 protein. It can be proposed that the HCMV UL136 protein may have important roles in processes such as cell-to-cell spread, and in maintaining cell osmotic pressure and intracellular ion homeostasis during HCMV infection.

Effect of ATP and 2-oxoglutarate on the in vitro interaction between the NifA GAF domain and the GlnB protein of Azospirillum brasilense

Azospirillum brasilense is a diazotroph that associates with important agricultural crops and thus has potential to be a nitrogen biofertilizer. The A. brasilense transcription regulator NifA, which seems to be constitutively expressed, activates the transcription of nitrogen fixation genes. It has been suggested that the nitrogen status-signaling protein GlnB regulates NifA activity by direct interaction with the NifA N-terminal GAF domain, preventing the inhibitory effect of this domain under conditions of nitrogen fixation. In the present study, we show that an N-terminal truncated form of NifA no longer required GlnB for activity and lost regulation by ammonium. On the other hand, in trans co-expression of the N-terminal GAF domain inhibited the N-truncated protein in response to fixed nitrogen levels. We also used pull-down assays to show in vitro interaction between the purified N-terminal GAF domain of NifA and the GlnB protein. The results showed that A. brasilense GlnB interacts directly with the NifA N-terminal domain and this interaction is dependent on the presence of ATP and 2-oxoglutarate.

Prevention of etomidate-induced myoclonus during anesthetic induction by pretreatment with dexmedetomidine

Myoclonus induced by etomidate during induction of general anesthesia is undesirable. This study evaluated the effect of dexmedetomidine (DEX) pretreatment on the incidence and severity of etomidate-induced myoclonus. Ninety patients undergoing elective surgical procedures were randomly allocated to three groups (n=30 each) for intravenous administration of 10 mL isotonic saline (group I), 0.5 µg/kg DEX in 10 mL isotonic saline (group II), or 1.0 µg/kg DEX in 10 mL isotonic saline (group III) over 10 min. All groups subsequently received 0.3 mg/kg etomidate by intravenous push injection. The incidence and severity of myoclonus were recorded for 1 min after etomidate administration and the incidence of cardiovascular adverse events that occurred between the administration of the DEX infusion and 1 min after tracheal intubation was recorded. The incidence of myoclonus was significantly reduced in groups II and III (30.0 and 36.7%), compared with group I (63.3%). The incidence of severe sinus bradycardia was significantly increased in group III compared with group I (P<0.05), but there was no significant difference in heart rate in groups I and II. There were no significant differences in the incidence of low blood pressure among the 3 groups. Pretreatment with 0.5 and 1.0 µg/kg DEX significantly reduced the incidence of etomidate-induced myoclonus during anesthetic induction; however, 0.5 µg/kg DEX is recommended because it had fewer side effects.

Produção de isomaltulose a partir da transformação enzimática da sacarose, utilizando-se Erwinia sp D12 imobilizada com alginato de cálcio

A glicosiltransferase de Erwinia sp D12 é capaz de converter a sacarose em isomaltulose (6-o-alfa-glicopiranosil D-frutofuranose), um açúcar alternativo que apresenta baixo potencial cariogênico, e que pode ser utilizado em chocolates, gomas de mascar e balas. A isomaltulose é também utilizada na produção de isomalte, uma mistura de açúcar álcool, de baixo valor calórico e baixo potencial cariogênico. No estudo da influência dos componentes do meio de cultivo, na produção de glicosiltransferase, em frascos agitados, foi obtido maior atividade da enzima (12,8 unidades de atividade/mL do meio de cultura) em meio de cultura A constituído de melaço 12% (p/v) de sólidos solúveis totais, peptona 4% (p/v) e extrato de carne 0,4% (p/v). No estudo do efeito do tempo e da temperatura na fermentação da linhagem de Erwinia sp D12, em fermentador New Brunswick de 3L, contendo meio de cultura A, foi obtida maior atividade de glicosiltransferase (15,6 unidades de atividade/ mL de meio de cultura) na fase exponencial de crescimento após 8 horas de fermentação a 30ºC. Na produção de isomaltulose a partir da sacarose utilizando-se células de Erwinia sp D12 imobilizadas em alginato de cálcio, estudou-se o efeito da temperatura (25 - 35ºC) e da concentração de substrato (12,5 - 60% p/v). Foi obtido um rendimento em torno de 50% de isomaltulose, com soluções de sacarose entre 20-30% (p/v) a 35ºC. Concentrações em excesso de sacarose (ao redor de 40% p/v) afetaram a atividade da célula imobilizada, diminuindo a conversão de sacarose em isomaltulose. O xarope de isomaltulose foi purificado através de cromatografia de troca iônica e o eluato cristalizado por abaixamento de temperatura. Os cristais apresentaram 91,39% de isomaltulose.

Doubly fed wind turbine performance in variable grid conditions

Wind turbines based on doubly fed induction generators (DFIG) become the most popular solution in high power wind generation industry. While this topology provides great performance with the reduced power rating of power converter, it has more complicated structure in comparison with full-rated topologies, and therefore leads to complexity of control algorithms and electromechanical processes in the system. The purpose of presented study is to present a proper vector control scheme for the DFIG and overall control for the WT to investigate its behavior at different wind speeds and in different grid voltage conditions: voltage sags, magnitude and frequency variations. The key principles of variable-speed wind turbine were implemented in simulation model and demonstrated during the study. Then, based on developed control scheme and mathematical model, the set of simulation is made to analyze reactive power capabilities of the DFIG wind turbine. Further, the rating of rotor-side converter is modified to not only generate active rated active power, but also to fulfill Grid Codes. Results of modelling and analyzing of the DFIG WT behavior under different speeds and different voltage conditions are presented in the work.