985 resultados para phosphate buffer capacity
Resumo:
The laser induced non-destructive photoacoustic technique has been employed to measure the thermal diffusivity of lanthanum phosphate ceramics prepared by the sol–gel route. The thermal diffusivity value was evaluated by knowing the transition frequency between the thermally thin to thermally thick region from the log–log plot of photoacoustic amplitude versus chopping frequency. Analysis of the data was carried out on the basis of the one-dimensional model of Rosencwaig and Gersho. The present investigation reveals that the sintering temperature has great influence on the propagation of heat carriers and hence on the thermal diffusivity value. The results were interpreted in terms of variations in porosity with sintering temperature as well as with changes in grain size.
Resumo:
DC and AC electrical conductivity measurements in single crystals of diammonium hydrogen phosphate along the c axis show anomalous variations at 174, 246 and 416 K. The low-frequency dielectric constant also exhibits peaks exactly at these temperatures with a thermal hysteresis of 13 degrees C for the peak at 416 K. These specific features of the electrical properties are in agreement with earlier NMR second-moment data and can be identified with three distinct phase transitions that occur in the crystal. The electrical conductivity values have been found to increase linearly with impurity concentration in specimens doped with a specific amount of SO42- ions. The mechanisms of the phase transition and of the electrical conduction process are discussed in detail.
Resumo:
Results of axiswise measurements of the electrical conductivity (dc and ac) and dielectric constant of NH4H2PO4 confirm the occurrence of the recently suggested high‐temperature phase transition in this crystal (at 133 °C). The corresponding transition in ND4D2PO4 observed here for the first time takes place at 141.5 °C. The mechanism involved in these transitions and those associated with the electrical conduction and dielectric anomalies are explained on the basis of the motional effects of the ammonium ions in these crystals. Conductivity values for deuterated crystals give direct evidence for the predominance of protonic conduction throughout the entire range of temperatures studied (30–260 °C).
Resumo:
In this paper we discuss both theoretical and experimental results on the time dependence of the heat capacity of oriented Mn12 magnetic clusters when a magnetic field is applied along their easy axis. Our calculations are based on the existence of two contributions. The first one is associated with the thermal populations of the 21 different Sz levels in the two potential wells of the magnetic uniaxial anisotropy and the second one is related to the transitions between the Sz levels. We compare our theoretical predictions with experimental data on the heat capacity for different resolution times at different fields and temperatures.
Resumo:
Paper industry is one of the oldest and largest industries in Kerala. Despite the developments in the industry in terms of growth in output , value added and employment generation, many of the units face grave problems. Irrespective of the size of the plant, the problems of the industry are general in nature. The problems are galore in the supply, not the demand side. Amomg the problems, the important ones are: raw material scarcity, energy deficiency and obsolete technology. Further, the industry is subject to many controls by the Government — price control, product control and raw materials control — which result in the dwindling of profits and investments. Equally important are the reservations against the industry for polluting the environment byeffluent disposal on the one hand and affecting ecological balance by depleting the existing forest on the other. Apart from the large, medium and small pulp and paper mills, there are about 30 hand made paper units in Kerala which can be categorised as village and cottage industry. Almost all of these units began at the initiative and support of Khadi and Village Industries Commission. The primary purpose of these units is employment generation, and not profit making. Currently many of these units are in the red and many others are on the verge of closure. Therefore, a separate analysis of the growth performance, and problems and prospects of the hand made paper industry has also been attempted. It is analysed separately because of the very small size of the hand made paper units
Resumo:
The main objective of this thesis is to develop a compact chipless RFID tag with high data encoding capacity. The design and development of chipless RFID tag based on multiresonator and multiscatterer methods are presented first. An RFID tag using using SIR capable of 79bits is proposed. The thesis also deals with some of the properties of SIR like harmonic separation, independent control on resonant modes and the capability to change the electrical length. A chipless RFID reader working in a frequency band of 2.36GHz to 2.54GHz has been designed to show the feasibility of the RFID system. For a practical system, a new approach based on UWB Impulse Radar (UWB IR) technology is employed and the decoding methods from noisy backscattered signal are successfully demonstrated. The thesis also proposes a simple calibration procedure, which is able to decode the backscattered signal up to a distance of 80cm with 1mW output power.
Resumo:
Transport of live aquatic organisms which is more than a century old, perhaps started in the 1870's (Norris et al, 1960). Live fish transportation is an essential practice in aquaculture particularly in rural areas of developing countries representing the only means of supplying fry to small scale aqua culturists (Taylor and Ross, 1988). Very often, large numbers of fry, fingerlings, juveniles and adult fish are being transported from the hatchery to fish farms, fish farms to market, processors and consumers. Live fish command large economic importance in the fresh fish market than dead and iced fish. Medina Pizzali (2001) observed that live fish in the Kolkata market was usually sold at higher prices than dead fish and most consumers were prepared to pay premium prices for live fish, which is considered as the best guarantee of freshness, quality, and intrinsic characteristics of its flesh (better texture and delicate flavour) in comparison with fresh/chilled seafood. Various government and private agencies undertake transport of live fish for commercial live fish market or for artificial propagation of game
Resumo:
Eurocode 8 representing a new generation of structural design codes in Europe defines requirements for the design of buildings against earthquake action. In Central and Western Europe, the newly defined earthquake zones and corresponding design ground acceleration values, will lead in many cases to earthquake actions which are remarkably higher than those defined so far by the design codes used until now in Central Europe. In many cases, the weak points of masonry structures during an earthquake are the corner regions of the walls. Loading of masonry walls by earthquake action leads in most cases to high shear forces. The corresponding bending moment in such a wall typically causes a significant increase of the eccentricity of the normal force in the critical wall cross section. This in turn leads ultimately to a reduction of the size of the compression zone in unreinforced walls and a high concentration of normal stresses and shear stresses in the corner regions. Corner-Gap-Elements, consisting of a bearing beam located underneath the wall and made of a sufficiently strong material (such as reinforced concrete), reduce the effect of the eccentricity of the normal force and thus restricts the pinching effect of the compression zone. In fact, the deformation can be concentrated in the joint below the bearing beam. According to the principles of the Capacity Design philosophy, the masonry itself is protected from high stresses as a potential cause of brittle failure. Shaking table tests at the NTU Athens Earthquake Engineering Laboratory have proven the effectiveness of the Corner-Gap-Element. The following presentation will cover the evaluation of various experimental results as well as a numerical modeling of the observed phenomena.
Resumo:
Low phosphorus (P) in acid sandy soils of the West African Sudano-Sahelian zone is a major limitation to crop growth. To compare treatment effects on total dry matter (TDM) of crops and plant available P (P-Bray and isotopically exchangeable P), field experiments were carried out for 2 years at four sites where annual rainfall ranged from 560 to 850 mm and topsoil pH varied between 4.2 and 5.6. Main treatments were: (i) crop residue (CR) mulch at 500 and 2000 kg ha^-1, (ii) eight different rates and sources of P and (iii) cereal/legume rotations including millet (Pennisetum glaucum L.), sorhum [Sorghum bicolor (L.) Moench], cowpea (Vigna unguiculata Walp.) and groundnut (Arachis hypogaea L.). For the two Sahelian sites with large CR-induced differences in TDM, mulching did not modify significantly the soils' buffering capacity for phosphate ions but led to large increases in the intensity factor (C_p) and quantity of directly available soil P (E_1min). In the wetter Sudanian zone lacking effects of CR mulching on TDM mirrored a decline of E_1min with CR. Broadcast application of soluble single superphosphate (SSP) at 13 kg P ha^-1 led to large increases in C_p and quantity of E_1min at all sites which translated in respective TDM increases. The high agronomic efficiency of SSP placement (4 kg P ha^-1) across sites could be explained by consistent increases in the quantity factor which confirms the power of the isotopic exchange method in explaining management effects on crop growth across the region.
Resumo:
The surge in the urban population evident in most developing countries is a worldwide phenomenon, and often the result of drought, conflicts, poverty and the lack of education opportunities. In parallel with the growth of the cities is the growing need for food which leads to the burgeoning expansion of urban and peri-urban agriculture (UPA). In this context, urban agriculture (UA) contributes significantly to supplying local markets with both vegetable and animal produce. As an income generating activity, UA also contributes to the livelihoods of poor urban dwellers. In order to evaluate the nutrient status of urban soils in relation to garden management, this study assessed nutrient fluxes (inputs and outputs) in gardens on urban Gerif soils on the banks of the River Nile in Khartoum, the capital city of Sudan. To achieve this objective, a preliminary baseline survey was carried out to describe the structure of the existing garden systems. In cooperation with the author of another PhD thesis (Ms. Ishtiag Abdalla), alternative uses of cow dung in brick making kilns in urban Khartoum were assessed; and the socio-economic criteria of the brick kiln owners or agents, economical and plant nutritional value of animal dung and the gaseous emission related to brick making activities were assessed. A total of 40 household heads were interviewed using a semi-structured questionnaire to collect information on demographic, socio-economic and migratory characteristics of the household members, the gardening systems used and the problems encountered in urban gardening. Based on the results of this survey, gardens were divided into three groups: mixed vegetable-fodder gardens, mixed vegetable-subsistence livestock gardens and pure vegetable gardens. The results revealed that UA is the exclusive domain of men, 80% of them non-native to Khartoum. The harvested produce in all gardens was market oriented and represented the main source of income for 83% of the gardeners. Fast growing leafy vegetables such as Jew’s mallow (Corchorous olitorius L.), purslane (Portulaca oleracea L.) and rocket (Eruca sativa Mill.) were the dominant cultivated species. Most of the gardens (95%) were continuously cultivated throughout the year without any fallow period, unless they were flooded. Gardeners were not generally aware of the importance of crop diversity, which may help them overcome the strongly fluctuating market prices for their produce and thereby strengthen the contributions of UA to the overall productivity of the city. To measure nutrient fluxes, four gardens were selected and their nutrients inputs and outputs flows were monitored. In each garden, all plots were monitored for quantification of nutrient inputs and outputs. To determine soil chemical fertility parameters in each of the studied gardens, soil samples were taken from three selected plots at the beginning of the study in October 2007 (gardens L1, L2 and H1) and in April 2008 (garden H2) and at the end of the study period in March 2010. Additional soil sampling occurred in May 2009 to assess changes in the soil nutrient status after the River Nile flood of 2008 had receded. Samples of rain and irrigation water (river and well-water) were analyzed for nitrogen (N), phosphorus (P), potassium (K) and carbon (C) content to determine their nutrient inputs. Catchment traps were installed to quantify the sediment yield from the River Nile flood. To quantify the nutrient inputs of sediments, samples were analyzed for N, P, K and organic carbon (Corg) content, cation exchange capacity (CEC) and the particle size distribution. The total nutrient inputs were calculated by multiplying the sediment nutrient content by total sediment deposits on individual gardens. Nutrient output in the form of harvested yield was quantified at harvest of each crop. Plant samples from each field were dried, and analyzed for their N, P, K and Corg content. Cumulative leaching losses of mineral N and P were estimated in a single plot in garden L1 from December 1st 2008 to July 1st 2009 using 12 ion exchange resins cartridges. Nutrients were extracted and analyzed for nitrate (NO3--N), ammonium (NH4+-N) and phosphate PO4-3-P. Changes in soil nutrient balance were assessed as inputs minus outputs. The results showed that across gardens, soil N and P concentrations increased from 2007 to 2009, while particle size distribution remained unchanged. Sediment loads and their respective contents of N, P and Corg decreased significantly (P < 0.05) from the gardens of the downstream lowlands (L1 and L2) to the gardens of the upstream highlands (H1 and H2). No significant difference was found in K deposits. None of the gardens received organic fertilizers and the only mineral fertilizer applied was urea (46-0-0). This equaled 29, 30, 54, and 67% of total N inputs to gardens L1, L2, H1, and H2, respectively. Sediment deposits of the River Nile floods contributed on average 67, 94, 6 and 42% to the total N, P, K and C inputs in lowland gardens and 33, 86, 4 and 37% of total N, P, K and C inputs in highland gardens. Irrigation water and rainfall contributed substantially to K inputs representing 96, 92, 94 and 96% of total K influxes in garden L1, L2, H1 and H2, respectively. Following the same order, total annual DM yields in the gardens were 26, 18, 16 and 1.8 t ha-1. Annual leaching losses were estimated to be 0.02 kg NH4+-N ha-1 (SE = 0.004), 0.03 kg NO3--N ha-1 (SE = 0.002) and 0.005 kg PO4-3-P ha-1 (SE = 0.0007). Differences between nutrient inputs and outputs indicated negative nutrient balances for P and K and positive balances of N and C for all gardens. The negative balances in P and K call for adoptions of new agricultural techniques such as regular manure additions or mulching which may enhance the soil organic matter status. A quantification of fluxes not measured in our study such as N2-fixation, dry deposition and gaseous emissions of C and N would be necessary to comprehensively assess the sustainability of these intensive gardening systems. The second part of the survey dealt with the brick making kilns. A total of 50 brick kiln owners/or agents were interviewed from July to August 2009, using a semi-structured questionnaire. The data collected included general information such as age, family size, education, land ownership, number of kilns managed and/or owned, number of months that kilns were in operation, quantity of inputs (cow dung and fuel wood) used, prices of inputs and products across the production season. Information related to the share value of the land on which the kilns were built and annual income for urban farmers and annual returns from dung for the animal raisers was also collected. Using descriptive statistics, budget calculation and Gini coefficient, the results indicated that renting the land to brick making kilns yields a 5-fold higher return than the rent for agriculture. Gini coefficient showed that the kiln owners had a more equal income distribution compared to farmers. To estimate emission of greenhouse gases (GHGs) and losses of N, P, K, Corg and DM from cow dung when used in brick making, samples of cow dung (loose and compacted) were collected from different kilns and analyzed for their N, P, K and Corg content. The procedure modified by the Intergovernmental Panel on Climate Change (IPCC, 1994) was used to estimate the gaseous emissions of cow dung and fuel wood. The amount of deforested wood was estimated according to the default values for wood density given by Dixon et al. (1991) and the expansion ratio for branches and small trees given by Brown et al. (1989). The data showed the monetary value of added N and P from cow dung was lower than for mineral fertilizers. Annual consumption of compacted dung (381 t DM) as biomass fuel by far exceeded the consumption of fuel wood (36 t DM). Gaseous emissions from cow dung and fuel wood were dominated by CO2, CO and CH4. Considering that Gerif land in urban Khartoum supports a multifunctional land use system, efficient use of natural resources (forest, dung, land and water) will enhance the sustainability of the UA and brick making activities. Adoption of new kilns with higher energy efficiency will reduce the amount of biomass fuels (cow dung and wood) used the amount of GHGs emitted and the threat to the few remaining forests.
Resumo:
This research quantitatively evaluates the water retention capacity and flood control function of the forest catchments by using hydrological data of the large flood events which happened after the serious droughts. The objective sites are the Oodo Dam and the Sameura Dam catchments in Japan. The kinematic wave model, which considers saturated and unsaturated sub-surface soil zones, is used for the rainfall-runoff analysis. The result shows that possible storage volume of the Oodo Dam catchment is 162.26 MCM in 2005, while that of Samerua is 102.83 MCM in 2005 and 102.64 MCM in 2007. Flood control function of the Oodo Dam catchment is 173 mm in water depth in 2005, while the Sameura Dam catchment 114 mm in 2005 and 126 mm in 2007. This indicates that the Oodo Dam catchment has more than twice as big water capacity as its capacity (78.4 mm), while the Sameura Dam catchment has about one-fifth of the its storage capacity (693 mm).
Resumo:
Maize production in western Kenya is often limited by deficiencies of nitrogen and phosphorus. We assessed the effectiveness of Tithonia diversifolia green manure (tithonia), farmyard manure (FYM) and urea as sources of nitrogen (N) for maize when inorganic phosphorus (P) fertiliser was either broadcast (BR) or spot-placed in the planting hole (SP) for two consecutive seasons; October to December of 1998 and April to August of 1999 at two sites; Nyabeda and Khwisero in western Kenya. A randomised complete block design with four replications was used. Maize yields were higher at Nyabeda and responded to P application better than at Khwisero. At the same N rate, tithonia and FYM were as effective as urea in increasing maize yields at both sites. There were no significant differences in maize yields when phosphate fertiliser was either BR or SP regardless of the N source used in the first season. However, in the second season, the residual yields for the BR treatments were consistently higher than those of the SP. Our results suggest that tithonia and FYM can substitute for urea as N sources and that fertiliser P should be broadcast and incorporated together with the organic materials at the time of planting to save on labour costs.
Resumo:
Frequent shifts in policy on fertiliser markets have occurred in Ethiopia with the aim of facilitating both physical and economic access of farmers to fertiliser. The last shift was the introduction of a monopoly on each stage of the supply chain in 2008. Furthermore, government control of prices and margins as well as stockholding programmes are also present on the markets. This paper evaluates the effect of these policies on the integration of domestic with world markets of fertiliser, using cointegration methods. Time series data of diammonium phosphate (DAP) and urea prices on world, import and retail markets between 1971 and 2012 are used. The findings show high transmission of price signals from world markets to import prices for both DAP and urea. However, between import and retail prices there is no evidence of cointegration for urea, while for DAP full price transmission is concluded. In the retail market, domestic transaction costs associated with storing large volumes of fertiliser act as a buffer between import and retail prices, especially for urea. Therefore, economic benefits could be achieved by reducing the size of stocks and revising the demand estimation process.
Resumo:
We report the creation of strained silicon on silicon (SSOS) substrate technology. The method uses a relaxed SiGe buffer as a template for inducing tensile strain in a Si layer, which is then bonded to another Si handle wafer. The original Si wafer and the relaxed SiGe buffer are subsequently removed, thereby transferring a strained-Si layer directly to Si substrate without intermediate SiGe or oxide layers. Complete removal of Ge from the structure was confirmed by cross-sectional transmission electron microscopy as well as secondary ion mass spectrometry. A plan-view transmission electron microscopy study of the strained-Si/Si interface reveals that the lattice-mismatch between the layers is accommodated by an orthogonal array of edge dislocations. This misfit dislocation array, which forms upon bonding, is geometrically necessary and has an average spacing of approximately 40nm, in excellent agreement with established dislocation theory. To our knowledge, this is the first study of a chemically homogeneous, yet lattice-mismatched, interface.
Resumo:
Aim: Examine the relationship between the functional capacity and the quality of life related to health in university workers. Methodology: Cross-sectional study in 146 subjects, divided in two groups: Low functional Capacity (< 9 METs) and High functional Capacity (> 9.1 METs). We evaluated quality of life related to health (HRQOL-Health Questionnaire SF-12) and functional capacity (Questionnaire PAR/PAF) as indicators of health status. Results: 47.3% (69 men) and 52.7% (78 women). The average age of the groups was 35.0 ± 9.7 years (range 19,0-60,0 years). For HRQOL, the average found in the population assessed was 45.2 ± 4.42 (range 33,0-58,1) and 43.8 ± 6.87 (range 19,8-43,8) in components Physical Component Summary (PCS-12) and Mental Component Summary (MCS-12), respectively p = NS. Significant differences were found when comparing functional ability and sex, p<0,001 in both groups. Similarly, sex and mental component MCS-12 (group of Lower Functional) p = 0,049 as well as women and the physical component PCS-12, p = 0,05 between groups. Finally, a better score in HRQL observed in the group of High Capacity and functional components in both sex OR 0.59 (0.25-1.38). Conclusions: The results of this study demonstrate the relationship between High functional Capacity and a better HRQOL in this population.