Investigations of a thermosensitive gel to temporarily occlude crural arteries in femoro-distal bypass surgery.

OBJECTIVES: Long occlusions in calcified crural arteries are a major cause of endovascular technical failure in patients with critical limb ischaemia. Therefore, distal bypasses are mainly performed in patients with heavily calcified arteries and with consequently delicate clamping. A new reverse thermosensitive polymer (RTP) is an alternative option to occlude target vessels. The aim of the study is to report our technical experience with RTP and to assess its safety and efficiency to temporarily occlude small calcified arteries during anastomosis time. METHODS: Between July 2010 and December 2011, we used RTP to occlude crural arteries in 20 consecutive patients with 20 venous distal bypasses. We recorded several operative parameters, such as volume of injected RTP, duration of occlusion and anastomotic time. Quality of occlusion was subjectively evaluated. Routine on-table angiography was performed to search for plug emboli. Primary patency, limb salvage and survival rates were reported at 6 months. RESULTS: In all patients, crural artery occlusion was achieved with the RTP without the use of an adjunct occlusion device. Mean volume of RTP used was 0.3 ml proximally and 0.25 ml distally. Mean duration of occlusion was 14.4 ± 4.5 min, while completion of the distal anastomosis lasted 13.4 ± 4.3 min. Quality of occlusion was judged as excellent in eight cases and good in 12 cases. Residual plugs were observed in two patients and removed with an embolectomy catheter, before we amended the technique for dissolution of RTP. At 6 months, primary patency rate was 75% but limb salvage rate was 87.5%. The 30-day mortality rate was 10%. CONCLUSIONS: This study shows that RTP is safe when properly dissolved and effective to occlude small calcified arteries for completion of distal anastomosis.

Capsid modified replicating adenovirus to selectively target colon cancer

Résumé: Pratiquement tous les cancers du colon contiennent des mutations dans la voie de signalisation de Wnt qui active constitutivement cette voie. Cette activation mène à la stabilisation de la β-catenine. La β-catenin est transportée dans le noyau ou elle active des gènes cible en interagissant avec le facteur de transcription de TCF/LEF. Des adénovirus qui peuvent sélectivement se répliquer dans les cellules tumorales sont les agents qui peuvent permettre la déstruction de la tumeur mais pas le tissu normal. In vitro, les adénovirus avec des sites d'attachement du facteur de transcription TCF dans les promoteurs de l'adénovirus montrent une sélectivité et une activité dans une large sélection de lignées cellulaires de cancer du colon. Au contraire, in vivo, quand les adénovirus modifiés sont injectés dans la circulation, ils sont moins efficaces à cause de leur fixation par le foie et à cause de l'absence d'expression du récepteur du Coxsackie-Adénovirus (CAR). Le but de ma thèse était de modifier la protéine principale de capside de l'adénovirus, fibre, pour augmenter l'infection des tumeurs du cancer du colon. La fibre de l'adénovirus est responsable de l'attachement aux cellules et de l'entrée virale. J'ai inséré un peptide RGD dans la boucle HI de la fibre qui dirige sélectivement le virus aux récepteurs des integrines. Les integrines sont surexprimées par les cellules du cancer du colon et l'endothélium des vesseaux de la tumeur. Le virus re-ciblé, vKH6, a montré une activité accrue dans toutes les lignées cellulaires de cancer du colon, tandis que la sélectivité était maintenue. In vivo, vKH6 était supérieur au virus avec une capside de type sauvage en retardant la croissance de la tumeur. Le virus s'est répliqué plus vite et dispersé graduellement dans la tumeur. Cet effet a été montré par hybridation in situ et par PCR quantitative. Cependant, la monothérapie avec le virus n'a pu retarder la croissance des cellules tumorales SW620 greffées que de 2 semaines, mais à cause des régions non infectées la tumeur n'a pas pu être éliminée. Bien que la combinaison avec les chimiothérapies conventionnelles soit d'intérêt potentiel, presque toutes interfèrent avec la réplication virale. Les drogues antiangiogéniques sont des agents anti-tumoraux efficaces et prometteurs. Ces drogues n'interfèrent pas avec le cycle de vie de l'adénovirus. RAD001 est un dérivé de la rapamycine et il inhibe mTOR, une protéine kinase de la voie de PI3K. RAD001 empêche la croissance des cellules et il a aussi des effets anti-angiogénique et immunosuppressifs. RAD001 in vitro n'affecte pas l'expression des gènes viraux et la production virale. La combinaison de VKH6 et RAD001 in vivo a un effet additif en retardant la croissance de la tumeur. Des nouveaux peptides plus efficaces dans le ciblage de l'adénovirus sont nécessaires pour augmenter l'infection des tumeurs. J'ai créé un système de recombinaison qui permettra la sélection de nouveaux peptides dans le contexte du génome de l'adénovirus. Summary Virtually all colon cancers have mutations in the Wnt signalling pathway which result in the constitutive activation of the pathway. This activation leads to stabilization of β-catenin. β-catenin enters the nucleus and activates its target genes through interaction with the TCF transcription factor. Selectively replicating adenoviruses are promising novel agents that can destroy the tumour but not the surrounding normal tissue. In vitro, adenoviruses with TCF binding sites in the early viral promoters show selectivity and activity in a broad panel of viruses but in vivo they are less effective due to the lack of expression of the Coxsackie-Adenovirus receptor (CAR). The aim of my thesis was to modify the major capsid protein of the adenovirus, fibre, to increase the infection of colon tumours. Fibre of adenovirus is responsible for the binding to cells and for the viral uptake. I inserted an RGD binding peptide into the HI loop of fibre that selectively targets the virus to integrins that are overexpressed on tumour cells and on tumour endothelium. The retargeted virus, vKH6, showed increased activity in all colon cancer cell lines while selectivity was maintained. In vivo, vKH6 is superior to a matched virus with a wild type capsid in delaying tumour growth. vKH6 replicates and gradually spreads within the tumour as shown by in situ hybridization and Q-PCR. The virus alone can delay the growth of SW620 xenografts by 2 weeks but due to uninfected tumour regions the tumour cannot be cured. Although combination with conventional chemotherapeutics is of potential interest, almost all of them interfere with the viral replication. Growing evidence supports that anti-angiogenic drugs are effective and promising anti-tumour agents. These drugs interfere less with the viral life cycle. RAD001 is a rapamycin derivative and it blocks mTOR, a protein kinase in the PI3K pathway. RAD001 inhibits cell growth and has strong anti-angiogenic and immunosuppressive effects. RAD001 in vitro does not affect viral gene expression and viral burst size. In vivo vKH6 and RAD001 have an additive effect in delaying tumour growth, but tumour growth is still not completely inhibited. To further increase tumour infection new tumour specific targeting peptides are needed. I created an adenovirus display library that will allow the selection of targeting peptides. This system may also facilitate the production of fibre modified viruses.

A modified structural stress method for fatigue assessment of welded structures

Fatigue life assessment of weldedstructures is commonly based on the nominal stress method, but more flexible and accurate methods have been introduced. In general, the assessment accuracy is improved as more localized information about the weld is incorporated. The structural hot spot stress method includes the influence of macro geometric effects and structural discontinuities on the design stress but excludes the local features of the weld. In this thesis, the limitations of the structural hot spot stress method are discussed and a modified structural stress method with improved accuracy is developed and verified for selected welded details. The fatigue life of structures in the as-welded state consists mainly of crack growth from pre-existing cracks or defects. Crack growth rate depends on crack geometry and the stress state on the crack face plane. This means that the stress level and shape of the stress distribution in the assumed crack path governs thetotal fatigue life. In many structural details the stress distribution is similar and adequate fatigue life estimates can be obtained just by adjusting the stress level based on a single stress value, i.e., the structural hot spot stress. There are, however, cases for which the structural stress approach is less appropriate because the stress distribution differs significantly from the more common cases. Plate edge attachments and plates on elastic foundations are some examples of structures with this type of stress distribution. The importance of fillet weld size and weld load variation on the stress distribution is another central topic in this thesis. Structural hot spot stress determination is generally based on a procedure that involves extrapolation of plate surface stresses. Other possibilities for determining the structural hot spot stress is to extrapolate stresses through the thickness at the weld toe or to use Dong's method which includes through-thickness extrapolation at some distance from the weld toe. Both of these latter methods are less sensitive to the FE mesh used. Structural stress based on surface extrapolation is sensitive to the extrapolation points selected and to the FE mesh used near these points. Rules for proper meshing, however, are well defined and not difficult to apply. To improve the accuracy of the traditional structural hot spot stress, a multi-linear stress distribution is introduced. The magnitude of the weld toe stress after linearization is dependent on the weld size, weld load and plate thickness. Simple equations have been derived by comparing assessment results based on the local linear stress distribution and LEFM based calculations. The proposed method is called the modified structural stress method (MSHS) since the structural hot spot stress (SHS) value is corrected using information on weld size andweld load. The correction procedure is verified using fatigue test results found in the literature. Also, a test case was conducted comparing the proposed method with other local fatigue assessment methods.

A Study on Fractionation and Ultrafiltration of Proteins with Characterized Modified and Unmodified Membranes

Membrane filtration has become increasingly attractive in the processing of both foodand biotechnological products. However, the poor selectivity of the membranes and fouling are the critical factors limiting the development of UF systems for the specific fractionation of protein mixtures. This thesis gives an overview on fractionation of proteins from model protein solutions or from biological solutions. An attempt was made to improve the selectivity of the available membranes by modifying the membranes and by exploiting the different electrostatic interactions between the proteins and the membrane pore surfaces. Fractionation and UF behavior of proteins in the model solutions and in the corresponding biological solutions were compared. Characterization of the membranes and protein adsorptionto the membrane were investigated with combined flux and streaming potential studies. It has been shown that fouling of the membranes can be reduced using "self-rejecting" membranes at pH values where electrostatic repulsion is achieved between the membrane and the proteins in solution. This effect is best shown in UF of dilute single protein solutions at low ionic strengths and low pressures. Fractionation of model proteins in single, binary, and ternary solutionshas been carried out. The results have been compared to the results obtained from fractination of biological solutions. It was generally observed that fractination of proteins from biological solutions are more difficult to carry out owingto the presence of non studied protein components with different properties. Itcan be generally concluded that it is easier to enrich the smaller protein in the permeate but it is also possible to enrich the larger protein in the permeateat pH values close to the isoelectric point of the protein. It should be possible to find an optimal flux and modification to effectively improve the fractination of proteins even with very similar molar masses.

On the origin of the inertia: the modified Newtonian dynamics theory

The sameness between the inertial mass and the gravitational mass is an assumption and not a consequence of the equivalent principle is shown. In the context of the Sciama’s inertia theory, the sameness between the inertial mass and the gravitational mass is discussed and a certain condition which must be experimentally satisfied is given. The inertial force proposed by Sciama, in a simple case, is derived from the Assis’ inertia theory based in the introduction of a Weber type force. The origin of the inertial force is totally justified taking into account that the Weber force is, in fact, an approximation of a simple retarded potential, see [18, 19]. The way how the inertial forces are also derived from some solutions of the general relativistic equations is presented. We wonder if the theory of inertia of Assis is included in the framework of the General Relativity. In the context of the inertia developed in the present paper we establish the relation between the constant acceleration a0 , that appears in the classical Modified Newtonian Dynamics (M0ND) theory, with the Hubble constant H0 , i.e. a0 ≈ cH0 .

Recurrent Macular Edema in Central Retinal Vein Occlusion Treated with Intravitreal Ranibizumab using a Modified Treat and Extend Regimen.

Background: The aim of this study was to evaluate the stability over time of the individually defined interval of intravitreal ranibizumab injection (IVR) for the treatment of recurrent macular edema (ME) in central retinal vein occlusion (CRVO). Patients and Methods: A case series of treatment naïve patients followed in the Jules Gonin Eye Hospital for macular edema due to central retinal vein occlusion is presented. Patients were treated monthly with IVR until complete absence of fluid on qualitative SD-OCT with a minimum of 5 monthly IVR. Thereafter, they were followed according to a modified treat and extend regimen (mTER). Results: Twelve eyes (12 patients) with ME due to CRVO were included. The mean follow-up period was 31.3 months. Analysis showed that best corrected visual acuity (BCVA), central macular thickness and qualitative spectral domain optical coherence tomography (SD-OCT) showed comparable results under monthly interval, after titration of an individualized interval and when performed in a series. 78 % of treating intervals were within ± 2 weeks of the first individually adjusted interval. The mean first defined interval was 4.3 weeks and the mean interval over time was 5.5 weeks (p = 0.003). There was a trend towards longer interval over time. Conclusion: The adjusted interval of retreatment of patients with ME due to CRVO showed a high stability with a trend toward longer duration over time. An mTER regimen seems to be valuable to follow patients with ME with good stabilization of VA.

Sensory characteristics of 'Douradão' peaches submitted to modified atmosphere packaging

The sensory, physical and chemical characteristics of 'Douradão' peaches cold stored in different modified atmosphere packaging (LDPE bags of 30, 50, 60, 75µm thickness) were studied. After 14, 21 and 28 days of cold storage (1 ± 1 ºC and 90 ± 5% RH), samples were withdrawn from MAP and kept during 4 days in ambient air for ripening. Descriptive terminology and sensory profile of the peaches were developed by methodology based on the Quantitative Descriptive Analysis (QDA). The assessors consensually defined the sensory descriptors, their respective reference materials and the descriptive evaluation ballot. Fourteen individuals were selected as judges based on their discrimination capacity and reproducibility. Seven descriptors were generated showing similarities and differences among the samples. The data were analysed by ANOVA, Tukey test and Principal Component Analysis (PCA). The atmospheres that developed inside the different packaging materials during cold storage differed significantly. The PCA showed that MA50 and MA60 treatments were more characterized by the fresh peach flavour, fresh appearance, juiciness and flesh firmness, and were effective for keeping good quality of 'Douradão' peaches during 28 d of cold storage. The Control and MA30 treatments were characterized by the mealiness, the MA75 treatment showed lower intensity for all attributes evaluated and they were ineffective to maintain good quality of the fruits during cold storage. Higher correlation coefficients (positive) were found between fresh appearance and flesh firmness (0.95), fresh appearance and juiciness (0.97), ratio and intensity of fresh peach smell (0.81), as well as higher correlation coefficients (negative) between Hue angle and intensity of yellow colour (-0.91), fresh appearance and mealiness (-0.92), juiciness and mealiness (-0.95), firmness and mealiness (-0.94).

Modified atmosphere packaging extending the storage life of 'douradão' peach

'Douradão' peach is a perishable product and when cold stored is subject to chilling injury. The objective of the experiment was to evaluate the effect of modified atmosphere packaging (MAP) and cold storage on quality and storage life of these peaches. Fruits were packed in polypropylene (PP) trays and placed inside low density polyethylene (LDPE) bags (30, 50, 60, 75 μm thickness) with active modified atmosphere (10 kPa CO2 + 1.5kPa O2, balance N2). The control was made with peaches held in nonwrapped PP trays. Fruits were kept at 1 ± 1 °C and 90 ± 5% relative humidity (RH) for 28 days and CO2 and O2 within packages was monitored every two days. After 14, 21 and 28 days, samples were withdrawn from MAP and kept in air at 25 ± 1 °C and 90 ± 5% RH for ripening. On the day of removal from the cold storage and after 4 days, peaches were evaluated for weight loss, decay incidence, flesh firmness, woolliness incidence, soluble solids content (SSC), titratable acidity (TA) and juice content. The results showed that MAP had influence on reducing weight loss and prevented postharvest decay. MAP of 1-2 kPa O2 and 3-6 kPa CO2 at 1 °C (from 50 and 60 μm LDPE films) were effective for keeping good quality of 'Douradão' peaches during 28 days of storage, the ripe fruits showed reduced incidence of woolliness, adequate juiciness and flesh firmness. Packages of 30 and 75 μm LDPE films were ineffective for reducing woolliness during cold storage. MAP fruits showed lower SSC and no relevant effect on TA. Control fruits did not present marketable conditions after 14 days of cold storage.