Determinação direta de Ca, Mg, Mn e Zn em amostras de leite de búfala da Ilha de Marajó por espectrometria de absorção atômica com chama (FAAS)

This work proposes an analytical procedure for direct determination of calcium, magnesium, manganese and zinc in buffalo milk by flame atomic absorption spectrometry (FAAS). Samples were diluted with a solution containing 10% (v/v) of water-soluble tertiary amines (CFA-C) at pH 8. For comparison, buffalo milk samples were digested with HNO3 and H2O2. According to a paired t-test, the results obtained in the determination of Ca, Mg, Mn and Zn in digested samples and in 10% (v/v) CFA-C medium were in agreement at a 95% confidence level. The developed procedure is simple, rapid, decrease the possibility of contamination and can be applied for the routine determination of Ca, Mg, Mn and Zn in buffalo milk samples without any difficulty caused by matrix constituents, such as fat content, and particle size distribution in the milk emulsion.

Reaproveitamento de óxidos de manganês de pilhas descartadas para eletrocatálise da reação de redução de oxigênio em meio básico

The oxygen reduction reaction was studied in alkaline media using manganese oxides obtained from spent batteries as electrocatalysts. Three processes were used to recover manganese oxides from spent batteries. The particles obtained were in the range from 8 to 11 nm. The electrochemical experiments indicated a good electrocatalytic activity toward oxygen reduction using the different samples and showing approximately a direct transference of 4 electrons during the process. Even though all the processes were efficient, the best result was observed for the prepared sample using reactants of low cost.

Aplicação de métodos quimiométricos na otimização da extração de Ca, Mg, K, Fe, Zn, Cu e Mn em folhas de braquiária

This work applied a 2² factorial design to the optimization of the extraction of seven elements (calcium, magnesium, potassium, iron, zinc, copper and manganese) in brachiaria leaves, determined by flame atomic absorption spectrometry. The factors sample mass and digestion type were evaluated at two levels: 200/500 mg, and dry/wet, respectively. Principal component analysis allowed simultaneous discrimination of all the significant effects in one biplot. Wet digestion and mass of 200 mg were considered the best conditions. The decrease of 60% in sample mass allowed to save costs and reagents. The method was validated through the estimation of figures of merit.

Uso de aditivos na biodegradação de madeira pelo fungo Ceriporiopsis subvermispora: efeito na peroxidação de lipídios dependente de manganês-peroxidase

Ceriporiopsis subvermispora is a selective fungus in the wood delignification and the most promising in biopulping. Through the lipid peroxidation initiated by manganese peroxidase (MnP), free radicals can be generated, which can act in the degradation of lignin nonphenolic structures. This work evaluated the prooxidant activity (based in lipid peroxidation) of enzymatic extracts from wood biodegradation by this fungus in cultures containing exogenous calcium, oxalic acid or soybean oil. It was observed that MnP significant activity is required to promote lipid peroxidation and wood delignification. Positive correlation between prooxidant activity x MnP was observed up to 300 IU kg-1 of wood.

New strategies for treatment and reuse of spent sulfidic caustic stream from petroleum industry

This work examines traditional and new routes for removal of H2S and other sulfur compounds from spent sufidic caustic (SSC). SH- (hydrogenosulfide) and S2- (sulfide) ions were quantitatively oxidized at 25 ºC using H2O2, NaOCl or a spent sulfochromic mixture. SH-/S2- ions were also removed via reaction with freshly prepared iron or manganese hydroxides, or after passing the SSC through strong basic anion exchange resins (OH- form). The treated caustic solution, as well as iron/manganese hydroxides, removed H2S from diesel samples at 25 ºC. SSC treatment via strong basic anion-exchange resins produced the treated caustic solution with the highest free alkalinity.

Método hidrometalúrgico para reciclagem de metais terras raras, cobalto, níquel, ferro e manganês de eletrodos negativos de baterias exauridas de Ni-MH de telefone celular

A hydrometallurgical method for the recovery of rare earth metals, cobalt, nickel, iron, and manganese from the negative electrodes of spent Ni - MH mobile phone batteries was developed. The rare earth compounds were obtained by chemical precipitation at pH 1.5, with sodium cerium sulfate (NaCe(SO4)2.H2O) and lanthanum sulfate (La2(SO4)3.H2O) as the major recovered components. Iron was recovered as Fe(OH)3 and FeO. Manganese was obtained as Mn3O4.The recovered Ni(OH)2 and Co(OH)2 were subsequently used to synthesize LiCoO2, LiNiO2 and CoO, for use as cathodes in ion-Li batteries. The anodes and recycled materials were characterized by analytical techniques.

Aplicações de enzimas na síntese e na modificação de polímeros

Enzymes are biological catalysts that offer great potential for use in the synthesis and modification of polymers, being more specific and greener than chemical catalysts. In this work, enzymes from the classes of hydrolases (lipase, cutinase and protease) and of oxidoreductases (horseradish peroxidase, manganese peroxidase and laccase) were identified as the main biocatalysts responsible for the synthesis of polymers. Biocatalysis can potentially be part of the life cycle of several polymers, including polyesters, polyurethanes, polycarbonates, polyamides, functionalized polysaccharides and polystyrene, allowing the synthesis of specialty macromolecules for fine applications and with higher added-value than commodity polymers.

Photoinhibition of Photosystem II. Kinetics, Photoprotection and Mechanism

Photosystem II (PSII) is susceptible to light-induced damage defined as photoinhibition. In natural conditions, plants are capable of repairing the photoinhibited PSII by on-going degradation and re-synthesis of the D1 reaction centre protein of PSII. Photoinhibition is induced by both visible and ultraviolet light and photoinhibition occurs under all light intensities with the same efficiency per photon. In my thesis work, I studied the reaction kinetics and mechanism of photoinhibition of PSII, as well as photoprotection in leaves of higher plants. Action spectroscopy was used to identify photoreceptors of photoinhibition. I found that the action spectrum of photoinhibition in vivo shows resemblance to the absorption spectra of manganese model compounds of the oxygen evolving complex (OEC) suggesting a role for manganese as a photoreceptor of photoinhibition under UV and visible light. In order to study the protective effect of non-photochemical quenching, the action spectrum was measured from leaves of wild type Arabidopsis thaliana and two mutants impaired in nonphotochemical quenching of chlorophyll a excitations. The findings of action spectroscopy and simulations of chlorophyll-based photoinhibition mechanisms suggested that quenching of antenna excitations protects less efficiently than would be expected if antenna chlorophylls were the only photoreceptors of photoinhibition. The reaction kinetics of prolonged photoinhibition was studied in leaves of Cucurbita maxima and Capsicum annuum. The results indicated that photoinhibitory decrease in both the oxygen evolution activity and ratio of variable to maximum fluorescence follows firstorder kinetics in vivo. The persistence of first-order kinetics suggests that already photoinhibited reaction centres do not protect against photoinhibition and that the mechanism of photoinhibition does not have a reversible intermediate. When Cucurbita maxima leaves were photoinhibited with saturating single-turnover flashes and continuous light, the light response curve of photoinhibition was found to be essentially a straight line with both types of illumination, suggesting that similar photoinhibition mechanisms might function during illumination with continuous light and during illumination with short flashes.

Study of mesoscopic tunnel junctions between two normal metals

The main purpose of this work was to study different kinds of metal-based tunnel junctions at low temperatures. The problem which had to be solved was creating a junction with appropriate properties at these temperatures. The materials for junctions were found experimentally. The goal was to find an alloy material that can provide a high quality tunnel junction, which remains in the normal conductive state at low temperatures without applying magnetic field. The fabrication technology of such a device, based on an alloy of aluminium and manganese, is described in detail. In this thesis theoretical properties of tunnel junctions are considered and results of experiments with tunnel junctions are described and quantitative properties of the junctions are analyzed based on the experimental data.

Effect of hydrodynamics on modelling, monitoring and control of crystallization

Crystallization is a purification method used to obtain crystalline product of a certain crystal size. It is one of the oldest industrial unit processes and commonly used in modern industry due to its good purification capability from rather impure solutions with reasonably low energy consumption. However, the process is extremely challenging to model and control because it involves inhomogeneous mixing and many simultaneous phenomena such as nucleation, crystal growth and agglomeration. All these phenomena are dependent on supersaturation, i.e. the difference between actual liquid phase concentration and solubility. Homogeneous mass and heat transfer in the crystallizer would greatly simplify modelling and control of crystallization processes, such conditions are, however, not the reality, especially in industrial scale processes. Consequently, the hydrodynamics of crystallizers, i.e. the combination of mixing, feed and product removal flows, and recycling of the suspension, needs to be thoroughly investigated. Understanding of hydrodynamics is important in crystallization, especially inlargerscale equipment where uniform flow conditions are difficult to attain. It is also important to understand different size scales of mixing; micro-, meso- and macromixing. Fast processes, like nucleation and chemical reactions, are typically highly dependent on micro- and mesomixing but macromixing, which equalizes the concentrations of all the species within the entire crystallizer, cannot be disregarded. This study investigates the influence of hydrodynamics on crystallization processes. Modelling of crystallizers with the mixed suspension mixed product removal (MSMPR) theory (ideal mixing), computational fluid dynamics (CFD), and a compartmental multiblock model is compared. The importance of proper verification of CFD and multiblock models is demonstrated. In addition, the influence of different hydrodynamic conditions on reactive crystallization process control is studied. Finally, the effect of extreme local supersaturation is studied using power ultrasound to initiate nucleation. The present work shows that mixing and chemical feeding conditions clearly affect induction time and cluster formation, nucleation, growth kinetics, and agglomeration. Consequently, the properties of crystalline end products, e.g. crystal size and crystal habit, can be influenced by management of mixing and feeding conditions. Impurities may have varying impacts on crystallization processes. As an example, manganese ions were shown to replace magnesium ions in the crystal lattice of magnesium sulphate heptahydrate, increasing the crystal growth rate significantly, whereas sodium ions showed no interaction at all. Modelling of continuous crystallization based on MSMPR theory showed that the model is feasible in a small laboratoryscale crystallizer, whereas in larger pilot- and industrial-scale crystallizers hydrodynamic effects should be taken into account. For that reason, CFD and multiblock modelling are shown to be effective tools for modelling crystallization with inhomogeneous mixing. The present work shows also that selection of the measurement point, or points in the case of multiprobe systems, is crucial when process analytical technology (PAT) is used to control larger scale crystallization. The thesis concludes by describing how control of local supersaturation by highly localized ultrasound was successfully applied to induce nucleation and to control polymorphism in reactive crystallization of L-glutamic acid.

Elemental analysis of wood materials by external millibeam thick target PIXE

PIXE (Particle Induce X-ray Emission spectrometry) was used for analysing stem bark and stem wood of Scots pine, Norway spruce and Silver birch. Thick samples were irradiated, in laboratory atmosphere, with 3 MeV protons and the beam current was measured indirectly using a photo multiplicator (PM) tube. Both point scans and bulk analyses were performed with the 1 mm diameter proton beam. In bulk analyses, whole bark and sectors of discs of the stem wood were dry ashed at 550 ˚C. The ashes were homogenised by shaking and prepared to target pellets for PIXE analyses. This procedure generated representative samples to be analysed, but the enrichment also enabled quantification of some additional trace elements. The ash contents obtained as a product of the sample preparation procedure also showed to be of great importance in the evaluation of results in environmental studies. Spot scans from the pith of pine wood outwards, showed clearly highest concentrations of manganese, calcium and zinc in the first spot irradiated, or 2-3 times higher than in the surrounding wood. For stem wood from the crown part of a pine this higher concentration level was found in the first four spots/mms, including the pith and the two following growth rings. Zinc showed increasing concentrations outwards in sapwood of the pine stem, with the over-all lowest concentrations in the inner half of the sapwood. This could indicate emigration of this element from sapwood being under transformation to heartwood. Point scans across sapwood of pine and spruce showed more distinct variations in concentrations relative to hearth wood. Higher concentrations of e.g. zinc, calcium and manganese were found in earlywood than in denser latewood. Very high concentrations of iron and copper were also seen for some earlywood increments. The ash content of stem bark is up to and order higher than for the stem wood. However, when the elemental concentration in ashes of bark and wood of the same disc were compared, these are very similar – this when trees are growing at spots with no anthropogenic contamination from the atmosphere. The largest difference was obtained for calcium which appeared at two times high concentrations in ashes of bark than in ashes of the wood (ratio of 2). Pine bark is often used in monitoring of atmospheric pollution, where concentrations in bark samples are compared. Here an alternative approach is suggested: Bark and the underlying stem wood of a pine trees are dry ashed and analysed. The elemental concentration in the bark ash is then compared to the concentration of the same element in the wood ash. Comparing bark to wood includes a normalisation for the varying availability of an element from the soil at different sites. When this comparison is done for the ashes of the materials, a normalisation is also obtained for the general and locally different enrichment of inorganic elements from wood to bark. Already a ratio >2 between the concentration in the bark ash and the concentration in the wood ash could indicate atmospheric pollution. For monitoring where bark is used, this way of “inwards” comparison is suggested - instead of comparing to results from analyses of bark from other trees (read reference areas), growing at sites with different soil and, locally, different climate conditions. This approach also enables evaluation of atmospheric pollution from sampling of only relative few individual trees –preferable during forest felling.

Mikkelin Pursialan pohjavesialueen haitta-aineet

Mikkelin talousvedestä kahden kolmasosan tullessa Pursialan pohjavesialueelta on alueen suojeleminen tärkeää. Pohjaveden laatua uhkaavat etenkin alueella sattuneet pohjavedenpilaantumistapaukset. Merkittävimmät pohjaveden pilaantumistapaukset ovat VAPO Oy:n sahan aiheuttama pohjaveden pilaantuminen kloorifenoleilla (CP) ja VR:n ratapölkkykyllästämön aiheuttama pohjaveden pilaantuminen kreosoottiöljyllä sekä Rinnekadun Nesteen aiheuttama pohjaveden pilaantuminen MTBE:llä. Alueella on tehty tutkimuksia ja kunnostuksia pilaantumiin liittyen, mutta näiden tuloksia ei ole aikaisemmin koottu yhteen. Tämän työn tavoitteena oli koota tulokset samaan aineistoon. Työssä keskityttiin kloorifenolien leviämisen tarkasteluun sen Pursialan pohjavedenottamolle muodostaman suurimman uhan vuoksi. Kallioperätietojen, maanpintatietojen ja näytetietojen pohjalta laadittiin myös pienoismalli CP-pilaantuman leviämisen kokonaiskuvan hahmottamiseksi. Työn tavoitteena oli lisäksi tehdä riskitarkastelua CP-pilaantumaan liittyen ja etsiä keinoja hallita havaittuja riskejä. Riskinhallintaan liittyen työssä tutkittiin kloorifenoleilla pilaantuneen alueen maaperä- ja kalliotietoja sekä pohjaveden laatutietoja. Pursialan pohjavedessä on runsaasti rautaa ja mangaania sekä aggressiivista hiilihappoa. Pohjaveden pH on alueella noin 6,5, lämpötila noin 7,5 ºC ja happipitoisuus noin 0,7 mg/l. Pursialan kaupunginalueen kallioperässä on havaittavissa VAPO Oy:n sahalta vedenottamolle etenevä kalliopainanne, jota pitkin CP etenee. Alueen kallioperä on kiillegneissiä, jossa on pohjois–etelä-suuntaista rakoilua. Maaperätuloksien perusteella on havaittavissa vettä hyvin johtavien maakerrosten jatkuminen koko vedenottamon ja sahan välisen matkan, mikä tarkoittaa, että CP-pitoisella pohjavedellä voi olla aiemmin oletettua nopeampikin yhteys sahalta vedenottamolle. Suurin CP-pitoisuus noin 100 000 µg/l on mitattu KY-5-altaan kohdalle asennetun M14-pohjavesiputken pohjasta. Talousvesiasetuksen raja-arvo CP:lle on 10 µg/l. Sahan ja vedenottamon puolivälissä on havaittu yli 10 000 µg/l meneviä CP-pitoisuuksia. Suurin vedenottamon kaivoista (kaivo 10) mitattu pitoisuus on 149 µg/l. Jakotukilta raakavedestä otetuissa näytteissä tai talousvedessä ei ole kuitenkaan havaittu talousvesiasetuksen ylittäviä CP-pitoisuuksia. Pienoismallin perusteella CP sijaitsee sahan alueella lähellä kallionpintaa ja hajaantuu koko pohjavesipatjaan vedenottamolle päin mentäessä. CP-mittaustuloksissa on havaittavissa pulssimaisuutta. Tämä johtuu todennäköisesti Saimaan pinnan vaihtelun seurauksena muuttuvasta rantaimeytyneen pohjaveden määrästä. Saimaan pinnan nousu näyttäisi tuloksien perusteella nostavan CP-pitoisuuksia saha-alueella ja laskevan lähellä vedenottamoa. Pohjaveden pintatietojen perusteella tehdyn tarkastelun mukaan pohjavesi voi kulkeutua sahalta vedenottamolle parhaimmillaan noin vuodessa. Työssä arvioitiin KY-5–liuoksen vuosittaiseksi käyttömääräksi noin 648–970 m3. Allassakkaa arvioitiin syntyneen yhteensä noin 10–31 m3. Pohjaveteen arvioitiin joutuneen toiminnan aikana yhteensä noin 3 000–4 000 kg CP:tä. Kloorifenolit esiintyvät pohjavedessä lähes täysin kloorifenolaatteina. Kloorifenolien hajoaminen ja muuntuminen pohjavedessä on epätodennäköistä. Käsitteellisen mallin mukaan kloorifenolipilaantuman suurimmat riskit aiheutuvat kloorifenolien mahdollisuudesta pilata Pursialan vedenottamon talousvesi. Tällä hetkellä riskejä hallitaan kloorifenolien leviämisen tarkkailulla, sahan ja vedenottamon puolivälissä sijaitsevalla koepumppauksella sekä varautumalla aktiivihiilijauheen syöttöön talousvesiprosessiin. Koepumppauksen avulla on saatu ylös tällä hetkellä noin 69 kg kloorifenoleita. Tutkimuksen perusteella suositeltavimmat riskinhallintatoimet tulevaisuudessa ovat sahalla sijaitseva kunnostuspumppaus, sahan ja vedenottamon väliin sijoittuva suojapumppaus- ja vesiverhoyhdistelmä sekä sahan rannan kautta tapahtuvan rantaimeytymisen estäminen.