Electrical Machine Product Development; Transmission to Lean Approach

The requirements set by the market for electrical machines become increasingly demanding requiring more sophisticated technological solutions. Companies producing electrical ma-chines are challenged to develop machines that provide competitive edge for the customer for example through increased efficiency, reliability or some customer specific special requirement. The objective of this thesis is to derive a proposal for the first steps to transform the electrical machine product development process of a manufacturing company towards lean product development. The current product development process in the company is presented together with the processes of four other companies interviewed for the thesis. On the basis of current processes of the electrical machine industry and the related literature, a generalized electrical machine product development process is derived. The management isms and –tools utilized by the companies are analyzed. Adoption of lean Pull-Event –reviews, Oobeya –management and Knowledge based product development are suggested as the initial steps of implementing lean product development paradigm in the manufacturing company. Proposals for refining the cur-rent product development process and increasing the stakeholder involvement in the development projects are made. Lean product development is finding its way to Finnish electrical machine industry, but the results will be available only after the methods have been implemented and adopted by the companies. There is some enthusiasm about the benefits of lean approach and if executed successfully it will provide competitive edge for the Finnish electrical machine industry.

Energy Efficiency of a Diesel-Electric MobileWorking Machine

The power demand of many mobile working machines such as mine loaders, straddle carriers and harvesters varies significantly during operation, and typically, the average power demand of a working machine is considerably lower than the demand for maximum power. Consequently, for most of the time, the diesel engine of a working machine operates at a poor efficiency far from its optimum efficiency range. However, the energy efficiency of dieseldriven working machines can be improved by electric hybridization. This way, the diesel engine can be dimensioned to operate within its optimum efficiency range, and the electric drive with its energy storages responds to changes in machine loading. A hybrid working machine can be implemented in many ways either as a parallel hybrid, a series hybrid or a combination of these two. The energy efficiency of hybrid working machines can be further enhanced by energy recovery and reuse. This doctoral thesis introduces the component models required in the simulation model of a working machine. Component efficiency maps are applied to the modelling; the efficiency maps for electrical machines are determined analytically in the whole torque–rotational speed plane based on the electricalmachine parameters. Furthermore, the thesis provides simulation models for parallel, series and parallel-series hybrid working machines. With these simulation models, the energy consumption of the working machine can be analysed. In addition, the hybridization process is introduced and described. The thesis provides a case example of the hybridization and dimensioning process of a working machine, starting from the work cycle of the machine. The selection and dimensioning of the hybrid system have a significant impact on the energy consumption of a hybrid working machine. The thesis compares the energy consumption of a working machine implemented by three different hybrid systems (parallel, series and parallel-series) and with different component dimensions. The payback time of a hybrid working machine and the energy storage lifetime are also estimated in the study.

Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

Maastotyökoneen ajomoottorin hybridisointiin soveltuvan napavaihteiston dynamiikan mallinnus.

Työn tavoitteena oli mallintaa maastotyökoneen ajomoottorin hybridisointiin soveltuvan napavaihteiston dynamiikka. Työ tehtiin osana Saimaan ammattikorkeakoulun tutkimusprojektia, jonka tarkoituksena oli ajomoottorin ja integroidun napavaihteiston kaupallistaminen maastotyökoneisiin. Maastotyökoneena simulointimallissa käytettiin tyypillistä maataloustraktoria, johon kytkettiin vielä peräkärry. Traktorin renkaiden napaan oli kytketty ajomoottorina toimiva sähkömoottori, jonka sisään simuloitu napavaihteisto oli integroitu. Napavaihteiston dynamiikan mallintamiseen käytettiin monikappaledynamiikan simulointiohjelmistoa (Adams). Ohjelmalle määritettiin napavaihteiston komponenttien parametrit, joista voitiin simuloida vaihteiston dynaaminen käyttäytyminen. Simuloidusta mallista saatiin kytkimiin kohdistuvat voimat kytkentätilanteessa sekä sähkömoottorin väännön suunnanvaihtotilanteessa eri akselin pituuksilla, eri kytkinten nopeuseroilla, eri traktorin painoilla ja eri kuormilla ajettaessa. Mallissa simuloitiin myös sähkömoottorin käyttäytyminen vaihteenvaihtotilanteessa eri pyörimisnopeuden säätimen kertoimilla. Työssä huomattiin, että akselin mitoituksella voitiin vaikuttaa vaihteistossa ilmeneviin voimiin kytkimen kytkentähetkellä. Myös kytkimen hammastuksessa olevalla hammasvälyksellä voitiin vaikuttaa kytkimiin kohdistuviin voimiin suunnanvaihtotilanteissa. Vaihteistoon kohdistuvista voimista voidaan jatkossa suunnitella kytkimen ja akselin profiili, jotta vaihteisto kestää siihen kohdistuvat voimat.

M-käsittelyn vaikutus lastuamalla valmistettavan tuotteen valmistuskustannuksiin

Paremmin lastuttavia M-käsiteltyjä teräksiä on käytetty yrityksissä jo yli 20 vuoden ajan. Ominaisuuksiensa ansiosta M-teräksillä on pystytty pienentämään koneistuskustannuksia ja parantamaan kilpailukykyä. Viime vuosien aikana lastuavat terät ja työstökoneet ovat kuitenkin kehittyneet ja ero M-terästen ja tavanomaisten terästen välillä on voinut kaventua. Tämän diplomityön tavoitteena oli tutkia, saavutetaanko M-teräksen käytöllä taloudellisia etuja nykyaikaisissa konepajaolosuhteissa. Tutkimuksessa vertailtiin M-käsitellyn ja tavanomaisen 42CrMo4 – teräksen koneistusta. Valmistuskokeissa tarkasteltiin terien kulumista, lastun muotoa ja pinnanlaatua. Koekappaleena toimi olakkeellinen kuusiomutteri M64 kierteellä. Tuotteita valmistettiin yli 500 kappaletta ja materiaalia poistettiin noin 2000 kg. Koetulosten perusteella tuotteille laskettiin koneistuskustannukset kuvitteellisessa yrityksessä. Ero materiaalien välillä oli suurin työvaiheissa, joissa lastuaminen oli jatkuvaa. Sisä- ja ulkosorvauksessa M-käsiteltyä terästä lastunneiden terien kestoikä oli noin kaksinkertainen ja kierteen sorvauksessa noin nelinkertainen tavalliseen teräkseen verrattuna. Hakkaavassa työstössä terien kestoikä oli molemmilla materiaaleilla sama. Työssä suoritettujen kokeiden ja kustannuslaskelmien perusteella, käyttämällä M-käsiteltyä terästä voidaan pienentää valmistuskustannuksia. Materiaalien välinen ero korostuu, kun hakkaavaa työstöä on vähän, sarjat ovat suuria ja tuotanto on miehittämätöntä.

Readout Electronics for Gas Electron Multiplier Detectors

The European Organization for Nuclear Research (CERN) operates the largest particle collider in the world. This particle collider is called the Large Hadron Collider (LHC) and it will undergo a maintenance break sometime in 2017 or 2018. During the break, the particle detectors, which operate around the particle collider, will be serviced and upgraded. Following the improvement in performance of the particle collider, the requirements for the detector electronics will be more demanding. In particular, the high amount of radiation during the operation of the particle collider sets requirements for the electronics that are uncommon in commercial electronics. Electronics that are built to function in the challenging environment of the collider have been designed at CERN. In order to meet the future challenges of data transmission, a GigaBit Transceiver data transmission module and an E-Link data bus have been developed. The next generation of readout electronics is designed to benefit from these technologies. However, the current readout electronics chips are not compatible with these technologies. As a result, in addition to new Gas Electron Multiplier (GEM) detectors and other technology, a new compatible chip is developed to function within the GEMs for the Compact Muon Solenoid (CMS) project. In this thesis, the objective was to study a data transmission interface that will be located on the readout chip between the E-Link bus and the control logic of the chip. The function of the module is to handle data transmission between the chip and the E-Link. In the study, a model of the interface was implemented with the Verilog hardware description language. This process was simulated by using chip design software by Cadence. State machines and operating principles with alternative possibilities for implementation are introduced in the E-Link interface design procedure. The functionality of the designed logic is demonstrated in simulation results, in which the implemented model is proven to be suitable for its task. Finally, suggestions that should be considered for improving the design have been presented.