Energy-dependent in-situ small-angle x-ray scattering study of nano-ceramics

R Winter, D Le Messurier, CM Martin; Cryst Rev 12 (2006) 3 Sponsorship: EPSRC, CCLRC, Pilkington

Na-23, Si-29, and C-13 MAS NMR investigation of glass-forming reactions between Na2CO3 and SiO2

Winter, Rudolf; Jones, A.R.; Greaves, G.N.; Smith, I.H., (2005) 'Na-23, Si-29, and C-13 MAS NMR investigation of glass-forming reactions between Na2CO3 and SiO2', Journal of Physical Chemistry B 109(49) pp.23154-23161 RAE2008

Inorganic glasses, glass-forming liquids and amorphizing solids

Greaves, George; Sen, S., (2007) 'Inorganic glasses, glass-forming liquids and amorphizing solids', Advances in Physics 56(1) pp.1-166 RAE2008

Tracing the reactive melting of glass-forming silicate batches by in situ Na-23 NMR

Winter, Rudolf; Jones, A.R.; Florian, P.; Massiot, D., (2005) 'Tracing the reactive melting of glass-forming silicate batches by in situ Na-23 NMR', Journal of Physical Chemistry B 109(10) pp.4324-4332 RAE2008

The Viking age glass beads of Ireland and their North Atlantic context

Hitherto, the majority of studies which have included the discussion of Viking glass beads have mainly focused on the assemblages from individual sites, with limited use of known parallels. Exceptions to this include recent publications regarding the Icelandic material and Callmer’s 1977 catalogue of the finds from mainland Scandinavia, now over thirty years old. Analysis of these finds from Ireland was, for the most part, non-existent. The aim of this research is to address this lack of analysis within Ireland, while incorporating the wider context of the beads within the Viking North Atlantic. The research thus examines the use of glass beads of diagnostically Scandinavian manufacture and import found in Ireland, particularly in relation to their context and distribution. The history of research from Ireland as well as from across the Viking world is considered and explored throughout the thesis, with critique of methods and discussions used. Focussed analysis of both published and unpublished material detailing artefacts from Scandinavia (especially Vestfold), Britain, Iceland, the Faroe Islands and L’Anse aux Meadows is presented within the thesis in order to provide the greater picture for the core section of the thesis, the glass beads found in Ireland. Three appendices are included within Volume 2, databases of the glass beads under discussion from Ireland, the Vestfold region graves in Norway and the topsoil finds from the Kaupang trading place, also located within Vestfold. These appendices therefore represent the first-hand analysis of glass beads by the author. In total, this research represents the most up-to-date analysis of Viking glass beads from Ireland and presents a new look at the patterns of use, trade and interpersonal contact that affected the everyday lives of individuals living within Viking Age Ireland.

[Performance review] Philip Glass, Galileo Galilei

Review of the European premiere of the opera Galileo Galilei by Philip Glass performed at The Goodman Theatre, Barbican Centre, London in November 2002.

Role of bonding time and temperature on the physical properties of coupled anisotropic conductive–nonconductive adhesive film for flip chip on glass technology

Using thermosetting epoxy based conductive adhesive films for the flip chip interconnect possess a great deal of attractions to the electronics manufacturing industries due to the ever increasing demands for miniaturized electronic products. Adhesive manufacturers have taken many attempts over the last decade to produce a number of types of adhesives and the coupled anisotropic conductive-nonconductive adhesive film is one of them. The successful formation of the flip chip interconnection using this particular type of adhesive depends on, among factors, how the physical properties of the adhesive changes during the bonding process. Experimental measurements of the temperature in the adhesive have revealed that the temperature becomes very close to the required maximum bonding temperature within the first 1s of the bonding time. The higher the bonding temperature the faster the ramp up of temperature is. A dynamic mechanical analysis (DMA) has been carried out to investigate the nature of the changes of the physical properties of the coupled anisotropic conductive-nonconductive adhesive film for a range of bonding parameters. Adhesive samples that are pre-cured at 170, 190 and 210°C for 3, 5 and 10s have been analyzed using a DMA instrument. The results have revealed that the glass transition temperature of this type of adhesive increases with the increase in the bonding time for the bonding temperatures that have been used in this work. For the curing time of 3 and 5s, the maximum glass transition temperature increases with the increase in the bonding temperature, but for the curing time of 10s the maximum glass transition temperature has been observed in the sample which is cured at 190°C. Based on these results it has been concluded that the optimal bonding temperature and time for this kind of adhesive are 190°C and 10s, respectively.

The influence of alkali metal chlorides on the loss of water from glass-ionomer dental cements

The water loss behaviour of a clinical glass-ionomer dental cement has been studied with and without the addition of alkali metal chlorides. Dehydrating conditions were provided by placing specimens in a desiccator over concentrated sulphuric acid. Cements were prepared using either pure water or an aqueous solution of metal chloride (LiCl, NaCl, KCl) at 1.0 mol/dm(3). In addition, NaCl at 0.5 mol/dm(3) was also used to fabricate cements. Disc-shaped specimens of size 6 mm diameter x 2 mm thickness were made, six performulation, and cured at 37 degrees C for 1 hour They were then exposed to desiccating conditions, and the mass measured at regular intervals. All formulations were found to lose water in a diffusion process that equilibrated after approximately 3 weeks. Diffusion coefficients ranged from 2.27 (0.13) x 10(9) with no additive to 1.85 (0.07) x 10(9) m(2)/s with 1.0 mol/dm(3) KCl. For the salts, diffusion coefficients decreased in the order LiCl > NaCl > KCl. There was no statistically significant difference between the diffusion coefficients for 1.0 and 0.5 mol/dm(3) NaCl. For all salts at 1.0 mol/dm(3) and also additive-free cements, equilibrium losses were, with statistical limits, the same, ranging from 6.23 to 6.34%. On the other hand, 0.5 mol/dm(3) NaCl lost significantly more water 7.05%.