Preparation of tetrahedral amorphous carbon films by filtered cathodic vacuum arc deposition

Tetrahedrally bonded amorphous carbon (ta-C) and nitrogen doped (ta-C:N) films were obtained at room temperature in a filtered cathodic vacuum arc (FCVA) system incorporating an off-plane double bend (S-bend) magnetic filter. The influence of the negative bias voltage applied to substrates (from -20 to -350 V) and the nitrogen background pressure (up to 10-3 Torr) on film properties was studied by scanning electron microscopy (SEM), electron energy loss spectroscopy (EELS), Raman spectroscopy, X-ray photoemission spectroscopy (XPS), secondary ion mass spectroscopy (SIMS) and X-ray reflectivity (XRR). The ta-C films showed sp3 fractions between 84% and 88%, and mass densities around 3.2 g/cm3 in the wide range of bias voltage studied. In contrast, the compressive stress showed a maximum value of 11 GPa for bias voltages around -90 V, whereas for lower and higher bias voltages the stress decreased to 6 GPa. As for the ta-C:N films grown at bias voltages below -200 V and with N contents up to 7%, it has been found that the N atoms were preferentially sp3 bonded to the carbon network with a reduction in stress below 8 GPa. Further increase in bias voltage or N content increased the sp2 fraction, leading to a reduction in film density to 2.7 g/cm3.

Single-photon detection using a quantum dot field effect transistor

A novel device for detection of single photons based on a GaAs/AlGaAs modulation doped field effect transistor (MODFET) which does not rely on avalanche processes is proposed. The optimal channel electron densities and quantum dot parameters for detection of single photons are discussed.

The history and fishery potential of Kisoro Minor Lakes part two: Preliminary survey of Lakes Mutanda and Mulehe fisheries 

The fisheries of Lakes Mutanda and Mulehe during 1998/9 were mainly at subsistence scale and only few fishers operated at irregular intervals. The commercial catch records between 1963 to 1999 showed that Lake Mulehe was landing more fish than Lake Mutanda despite the fact that Lake Mutanda (26.4 km2) was bigger than Lake Mulehe (4.11 cm2). The constant decline of catches was due to irregular restocking and applying low stocking densities of fry. However, restocking should consider using species that withstand low temperature (15-240C) in the district. These include Oreochromis niloticus (Nile tilapia), Macropterus salmoides (Black bass), and Cyprinus carpio (Common carp). Most of these species have either disappeared or declined to very low levels. Due to lack of commercial fish species for harvest, the fishers by 1998/9 resorted to harvesting the haplochromines, Clarias carsoni and edible frogs (Xenopus kigesiensis) as alternative resources. Experimental studies have shown the need and techniques to enhance fish production on these two lakes.

The Bayesian Approach to Signal Modelling

In this paper, an introduction to Bayesian methods in signal processing will be given. The paper starts by considering the important issues of model selection and parameter estimation and derives analytic expressions for the model probabilities of two simple models. The idea of marginal estimation of certain model parameter is then introduced and expressions are derived for the marginal probabilitiy densities for frequencies in white Gaussian noise and a Bayesian approach to general changepoint analysis is given. Numerical integration methods are introduced based on Markov chain Monte Carlo techniques and the Gibbs sampler in particular.

Ground vibration generated by trains in underground tunnels

A popular method used to reduce vibration transmitted from underground railways into nearby buildings is floating-slab track, whereby a concrete slab supporting the two rails is mounted on rubber bearings or steel springs to isolate it from the tunnel invert. This paper adds a track model to a previously developed three-dimensional tunnel model in order to assess the effectiveness of floating-slab track. A slab beam coupled to the tunnel in the wavenumber domain, with the slab bearings represented by an elastic layer, is examined first. A second beam representing the two rails together is then coupled to the slab, and axle masses representing a train are added to the rail beam. Power-spectral densities and RMS levels of soil vibration due to random roughness-displacement excitation between the masses and the rail beam are calculated. Analytical techniques are used to minimise the computational requirements of the model. The results demonstrate the inadequacy of simple mass-spring and Winkler-beam models with rigid foundations for the assessment of the vibration-isolation performance of railway track. They suggest that the achievable insertion loss is modest and that floating the track slab may in fact cause increased transmission of vibration under certain conditions. © 2006 Elsevier Ltd. All rights reserved.

Optimisation of stocking density of Thai silver barb (Barbodes gonionotus Bleeker) in the duckweed-fed four species polyculture system

The optimisation of stocking density of Thai silver barb (Barbodes gonionotus) in the polyculture with Labeo rohita, Catla cat/a and Cyprinus cmpio was investigated in seasonal ponds. Three different stocking densities of Thai silver barb i.e., 5,000, 6,000 and 7,000 fingerlings ha-1 were tested with stocking density of carps fixed at the rate of 10,000 fingerlings ha-1 Duckweed was applied to all ponds supplemented with rice bran and oil cake. There were no significant variations on either water quality parameters or abundance of planktonic organisms due to the different stocking densities of silver barb. A significantly higher fish production (p

Physiological modelling for improved reliability in silhouette-driven gradient-based hand tracking

We present a gradient-based motion capture system that robustly tracks a human hand, based on abstracted visual information - silhouettes. Despite the ambiguity in the visual data and despite the vulnerability of gradient-based methods in the face of such ambiguity, we minimise problems related to misfit by using a model of the hand's physiology, which is entirely non-visual, subject-invariant, and assumed to be known a priori. By modelling seven distinct aspects of the hand's physiology we derive prior densities which are incorporated into the tracking system within a Bayesian framework. We demonstrate how the posterior is formed, and how our formulation leads to the extraction of the maximum a posteriori estimate using a gradient-based search. Our results demonstrate an enormous improvement in tracking precision and reliability, while also achieving near real-time performance. © 2009 IEEE.

Effect of pond aeration on growth and survival of Penaeus monodon Fab.

The effect of paddle wheel aeration on shrimp growth and survival were studied at a commercial farm at Chandipur coast of Orissa, India, at different stocking densities of Penaeus monodon. Four different aeration patterns were adopted and evaluated. Influence of individual aeration pattern on average survival rate was not highly significant (p<0.05) at different stocking densities, while different aeration patterns had significant influence (p

Influence of stocking density on the culture potential of freshwater catfish Pangasius pangasius in pond

Influence of stocking density on the production of freshwater catfish Pangasius pangasius with formulated feed in ponds was studied. The fish fry were collected from the Meghna river near Chandpur which is a natural breeding ground of this fish. Three stocking densities chosen during this experiment were 5000, 8000 and 11000 fry/ha with an initial weight of 42.57 ±2.51 g. The formulated feed was prepared in the laboratory which contained 45% fish meal, 30% mustard oil cake, 15% wheat bran and 10% rice bran to supply 40.48% protein in feed. The growth of P. pangasius in terms of net weight gain was 409.49, 266.49 and 236.37 g at the 5000/ha, 8000/ha and 11000/ha stocking densities respectively, which was statistically significant (p<0.05). High food conversion ratio (FCR) was also observed during this research study which ranged between 7.06 to 7.72. A production of 2.6 tons/ha at the stocking density of 11000/ha; 2.13 tons/ha at the stocking density of 8000/ha and 2.04 tons/ha at the stocking density of 5000/ha was obtained, while the growth of individual fish at the end of experiment was in opposite order. The result of this experiment indicates that stocking density has significant influence on the culture potential of freshwater catfish P.pangasius.

Polyculture of freshwater prawn, Macrobrachium rosenbergii, de Man with carps: effects of prawn stocking density

Effects of three stocking densities, viz., 35, 50 and 65/decimal (1 decimal = 40.48 m2) of juvenile freshwater prawn (Macrobrachium rosenbergii) on prawn and fish production were tested in a polycuture system with silver carp (Hypophthalmichthys molitrix), catla (Catla catla), Grass carp (Ctenophmyngodon idella) and silver barb (Barbodes gonionotus). The fish stocking density was 19/decimal with the species combination of silver carp-10, catlac-6, grass carp-1 and silver barb-2. In a 8-month culture period, the prawn yield 423 ± 144 kg/ha was significantly lower (P< 0.5) with the prawn stocking density of 35/decimal than that of 548 ± 178 kg/ha and 662 ± 243 kg/ha with 50 and 65/decimal respectively. The fish production (1844-1891 kg/ha) did not differ significantly (p <0.05) among the three treatments indicating that prawn stocking densities had no influence on fish yield. The lower mean harvest weight (62 g) and survival rate (67 g) and higher yield (2.67 kg/decimal) with the highest stocking rate of prawn reveals that as density was increased, prawn survival and individual weight at harvest decreased but total yield increased.

Culture potentials of bata, Labeo bata under semi-intensive management system

Small indigenous fish species (SIS) provide food, nutrition, subsistence and supplemental income to a great majority of the people particularly the poor and disadvantaged people of Bangladesh. To date nobody explored the possibilities of culturing these species in combination with the indigenous major carps viz. catla, Catla catla; rohu, Labeo rohita, and mrigal Cirrhinus cirrhosus and grass carp, Ctenopharyngodon idellus. An experiment on the polyculture of carps with a popular SIS, bata (Labeo bata) was carried out to evaluate the production performance of carp-SIS culture in on-farm condition during 15 March to 15 September 2003. Three treatments each having three replications with different stocking densities of bata were tested keeping the carp species combination and stocking density similar in all the treatments viz. treatment 1 (T1), bata (5,000/ha) + catla, rohu and mrigal (5,000/ha at the ratio of 1:1:1) + grass carp (250/ha); treatment 2 (T2), bata (7,500/ha) + catla, rohu and mrigal (5,000/ha at the ratio of 1:1:1) + grass carp (250/ha); and treatment 3 (T3), bata (1 0,000/ha) + catla, rohu and mrigal (5,000/ha at the ratio of 1:1:1) + grass carp (250/ha). After six months rearing, the production obtained were 2,466±77, 2,395±85 and 2,074±72 kg/ha from T1, T2 and T3, respectively. The highest production was obtained from T1, where the stocking density of bata was the minimum (5,000/ha) while the lowest production was obtained from T1 [sic], where the stocking density of bata was maximum (10,000/ha). Significant difference (P<0.05) exists in the production levels as obtained from different treatments. The contribution of bata to total production was 10.31%, 13.96% and 14.38% in case of T1, T2 and T3, respectively.

Effect of stocking density on the production of common carp (Cyprinus carpio Lin.) in cages at Kaptai lake, Bangladesh

Growth, survival and food conversion ratio (FCR) of Cyprinus carpio in cages at different stocking density were studied in Kaptai lake. Fingerlings of common carp (12.47 ± 4.29 g) were stocked at 25/m2 , 50/m2 and 75/m2 each with replication in six floating net cages each of Sm x Sm x 4m and reared for 240 days. The growth rate was inversely related to the stocking density with the mean weights of 325.5 ± 11.74 g, 268.99± 8.44 g and 167.0 ± 11.66 g at low, medium and high densities, respectively. At harvest, standing crop biomass averaged 7 .82, 12.83 and 11.58 kg with the survival of 98.9%, 97.6% and 94.4% and food conversion ratios of 4.51, 3.82 and 4.21 for the above three densities, respectively. Weight gain and production at density 25 fish/m 2 were significantly different (p< 0.01) from other two densities. Water quality was not affected in the cages having different stocking densities.

Culture of green algae Chlorella ellipsoidea in inexpensive media

The culture of the of green alga Chlorella ellipsoidea was conducted under natural conditions at the same place simultaneously in five different media, viz., medium-I (inorganic medium), medium-II (powdered whole-pulse medium), medium-III (medium of pulse bran), medium-IV (mixed medium = 50% inorganic medium + 50% whole-pulse powder medium), medium-V (mixed medium = 50% inorganic medium + 50% pulse bran medium). The culture was done in 500 ml conical flask. Growth rates of C. ellipsoidea in five different media were different and reached maximum cell densities of 0.63 x 10^6 cells per ml in 8 days in medium-I, 4.02 x 10^6 cells per ml in 10 days in medium-II, 3.62 x 10^6 cells per ml in 9 days in medium-III, 4.38 x 10^6 cells per ml in 11 days in medium-IV and 4.36 x 10^6 cells per ml in 11 days in medium-V. The range of air temperature was 20 to 33°C and that of culture media was 24 to 32°C and light intensity was 2000 to 7000 lux during the culture period. The inexpensive culture media were found to be significantly useful for algal culture.

Larval rearing and fry raising of Pangasius sutchi(Fowler)

Pangasius sutchi were artificially bred for determining the hatching success and larval growth response to live food in relation to varying stocking densities. The fertilized eggs were hatched out with successful hatching rates ranging between 60 and 63%. Newly hatched larvae of 4.4 mm average length were reared using Tubifex as live food in metallic trays with water temperature of 27 to 29.5°C and dissolved oxygen level of 3.88 to 6.22 mg/1 for 6-day with an average survival rate of75.56±13.25%. The P. sutchifry of9- day old were further reared using Tubifex in the polythene covered metallic trays at the stocking densities of 2-7 fry per litre of water for a period of 14 day. P. sutchi fry raising at 4 individual per litre of water for 14 day gives better results in terms of survival and growth.

Methods of patterning magnetic fields using bulk superconductors

High Temperature superconductors are able to carry very high current densities, and thereby sustain very high magnetic fields. There are many projects which use the first property and these have concentrated on power generation, transmission and utilization, however there are relatively few which are currently exploiting the ability to sustain high magnetic fields. There are two main reasons for this: high field wound magnets can and have been made from both BSCCO and YBCO but currently their cost is much higher than the alternative provided by low Tc materials such as Nb3Sn and NbTi. An alternative form of the material is the bulk form which can be magnetized to high fields and using flux pumping this can be done in situ. This paper explores some of the applications of bulk superconductors and describes methods of producing field patterns using the highly uniform magnetic fields required for MRI and accelerator magnets as the frame of reference. The patterns are not limited to uniform fields and it is entirely possible to produce a field varying sinusoidally in space such as would be required for a motor or a generator. The scheme described in this paper describes a dipole magnet such as is found in an accelerator magnet. The tunnel is 30 × 50 × 1000 mm and we achieve a uniformity of better than 200 ppm over the 1000 mm length and better than 1 ppm over the central 500 mm region. The paper presents results for both the overall uniformity and the integrated uniformity which is 302 ppm over the 1000 mm length. © 2010 IEEE.