Uncertainty of Efficiency Measurements in Electric Drives

The two central goals of this master's thesis are to serve as a guidebook on the determination of uncertainty in efficiency measurements and to investigate sources of uncertainty in efficiency measurements in the field of electric drives by a literature review, mathematical modeling and experimental means. The influence of individual sources of uncertainty on the total instrumental uncertainty is investigated with the help of mathematical models derived for a balance and a direct air cooled calorimeter. The losses of a frequency converter and an induction motor are measured with the input-output method and a balance calorimeter at 50 and 100 % loads. A software linking features of Matlab and Excel is created to process measurement data, calculate uncertainties and to calculate and visualize results. The uncertainties are combined with both the worst case and the realistic perturbation method and distributions of uncertainty by source are shown based on experimental results. A comparison of the calculated uncertainties suggests that the balance calorimeter determines losses more accurately than the input-output method with a relative RPM uncertainty of 1.46 % compared to 3.78 - 12.74 % respectively with 95 % level of confidence at the 93 % induction motor efficiency or higher. As some principles in uncertainty analysis are open to interpretation the views and decisions of the analyst can have noticeable influence on the uncertainty in the measurement result.

Energy efficiency and moisture diffusivity of apple slices during convective drying

Abstract The present study aimed at investigating the influences of drying air temperature and flow rate on energy parameters and dehydration behaviour of apple slices. For this purpose, apple slices were dried in a convective dryer at air temperatures of 50, 60 and 70 °C, and air velocities of 1, 1.5 and 2 m s–1. Dehydration rate increased as the air temperature and flow rate increased from 50 to 70 °C and 1 to 2 m s–1, respectively. The effective moisture diffusivity was determined to be in the range of 6.75×10–10-1.28×10–9 m2 s–1. Results of data analysis showed that the maximum energy consumption (23.94 kW h) belonged to 50 °C and 2 m s–1 and the minimum (13.89 kW h) belonged to 70 °C and 1 m s–1 treatment. Energy efficiency values were in the range of 2.87-9.11%. Moreover, the results indicated that any increment in the air temperature increases thermal and drying efficiencies while any increment in the air flow rate decreases both of them.

Telahiomon tuotannon läpimenoajan ja laadun optimointi

Tämän diplomityön tarkoituksena on tunnistaa UPM Kymin telahiomon tuotannon läpimenoaikaan sekä laatuun vaikuttavia tekijöitä ja löytää keinot niiden optimoimiseksi, jotta hiontatuotannon kustannustehokkuus parantuisi. Tutkimusmenetelminä työssä käytetään Kymin telahiomon tuotannon läpimenoaikojen telakohtaista mittaamista ja hionnasta tehtyjen mittausraporttien, pinnoituksista ja hionnoista tehtyjen ostotilauksien sekä SAP R/3-toiminnanohjausjärjestelmästä saatavan kunnossapitodatan tutkintaa. Tiedon lähteenä on käytetty myös kirjallisuutta ja UPM henkilöstön sekä toimittajien haastatteluita. Muiden telahiomojen aikaansaamaan laatuun ja tuotannon läpimenoaikaan verrattuna Kymin telahiomon keskimääräiset hiontatuotannon läpimenoajat ovat telasta riippuen kaksinkertaisia tai jopa lähes nelinkertaisia, vaikka pinnankarheus jää osassa teloista alle asetetun tavoitteen. Telahiomojen muototoleransseissa ei ole niin merkittäviä eroja, mitkä selittäisivät Kymin pidemmät hiontatuotannon läpimenoajat. Tämän takia muototoleransseja ei ole päädytty muuttamaan työn aikana, mutta käyttökokemusten mukaan pinnankarheusvaatimusta voidaan laskea. Telahiontaprosessin muotohiontavaihe on suurin hiontatuotannon läpimenoaikaan ja kustannuksiin vaikuttava tekijä. Hiontamenetelmien ja hionta-arvojen optimoimisella, hiontatyökalujen lastuamiskyvyn ylläpitämisellä, telahiontatuotannon yliprosessoinnin ehkäisyllä ja laatutoleransseihin tyytymisellä voidaan lyhentää kymmeniä tunteja telahiomon tuotannon läpimenoaikaa. Mittausraporttien mukaan merkittävin muutos telahiontaprosessin kustannuksiin ja hiontatuotannon läpimenoaikaan saadaan noudattamalla laatutoleransseja. Telojen kunnossapitoon liittyviä kustannuksia syntyy turhaan lisää, kun vaihdetaan ja hiotaan käyttökelpoisia teloja sekä uudelleen pinnoitetaan teloja, joiden pinnoitepaksuus on vielä riittävä. Pinnoitepaksuuden seurannalla voidaan minimoida telojen ennenaikaiset uudelleenpinnoitukset. Mittalaitteiden avulla pystyy optimoimaan telojen hiontavälit. Hiontavälien optimointi lyhentää myös hiontajonoa. Tällöin voidaan hyödyntää suunnitellun hiontajärjestyksen tuomia etuja tehokkaammin ja saavuttaa nopeampia tuotannon läpimenoaikoja.

Drying peanut seed using air ambient temperature at low relative humidity

The moisture content of peanut kernel (Arachis hypogaea L.) at digging ranges from 30 to 50% on a wet basis (w.b.). The seed moisture content must be reduced to 10.5% or below before seeds can be graded and marketed. After digging, peanuts are cured on a window sill for two to five days then mechanically separated from the vine. Heated air is used to further dry the peanuts from approximately 18 to 10% moisture content w.b. Drying is required to maintain peanut seed and grain quality. Traditional dryers pass a high temperature and high humidity air stream through the seed mass. The drying time is long because the system is inefficient and the high temperature increases the risk of thermal damage to the kernels. New technology identified as heat pipe technology (HPT) is available and has the unique feature of removing the moisture from the air stream before it is heated and passed through the seed. A study was conducted to evaluate the performance of the HPT system in drying peanut seed. The seeds inside the shells were dried from 17.4 to 7.3% in 14 hours and 11 minutes, with a rate of moisture removal of 0.71% mc per hour. This drying process caused no reduction in seed quality as measured by the standard germination, accelerated ageing and field emergence tests. It was concluded that the HPT system is a promising technology for drying peanut seed when efficiency and maintenance of physiological quality are desired.

Motor Types Comparison Determining Efficiency in Pumping Systems

Pumping, fan and compressor systems consume most of the motor electricity power in both the industrial and services sectors. A variable speed drive brings relevant improvements in a fluid system leading to energy saving that further on can be translated into Mtons reduction of CO 2 emissions. Standards and regulations are being adopted for fluid handling systems to limit the less efficiency pumps out of the European market on the coming years and a greater potential in energy savings is dictated by the Energy Efficiency Index (EEI) requirements for the whole pumping system and integrated pumps. Electric motors also have an International Efficiency (IE) classification in order to introduce higher efficiency motors into the market. In this thesis, the applicability of mid-size common electric motor types to industrial pumping system took place comparing the motor efficiency characteristics with each other and by analyzing the effect of motor dimensioning on the pumping system and its impact in the energy consumption.

Efficiency of methods to detect Sclerotinia sclerotiorum in commercial soybean seed lots

Most soybean pathogens are seed transmitted, deserving emphasis the fungus Sclerotinia sclerotiorum, which has been presenting worrying levels of field incidence in some soybean cropping areas in several Brazilian states. The objective of this study was to verify the efficiency of different methods for detecting S. sclerotiorum on soybean seeds artificially infected in the laboratory and from field production areas with a historical disease incidence. Seed samples of seven different cultivars collected from naturally infested fields, and one seed sample artificially inoculated in the laboratory were used. The following detection methods recommended in the literature were compared: Blotter test at 7 ºC, 14 ºC, and 21 ºC; Rolled Paper; and Neon-S. Results demonstrated that these methods showed no repeatability and had a low sensitivity for detecting the pathogen in seeds from areas with disease incidence. They were effective, however, for its detection on artificially inoculated seeds. In the Blotter test method at 7 ºC, there was a lower incidence of other fungi considered undesirable during seed analysis.

Towards a better energy efficiency through a systems approach in an industrial forklift

The purpose of this study is to improve the potential energy recovery to electric energy in an electrohydraulic forklift system. The initial achieved result for energy saving ratio after structural optimization is 40 %. Component optimization is applied to the tested drive which consists of a DTC controlled electric servo motor directly running a reversible hydraulic pump. According to the study the energy efficiency and the energy recovery from the electro-hydraulic forklift system can be increased by 11 % units. New ideas and directions of further research were obtained during the study.

A high efficiency microturbine concept

There is a growing trend towards decentralized electricity and heat production throughout the world. Reciprocating engines and gas turbines have an essential role in the global decentralized energy markets and any improvement in their electrical efficiency has a significant impact from the environmental and economic viewpoints. This paper introduces an inter-cooled and recuperated two-shaft microturbine at 500 kW electric output range. The microturbine is optimized for a realistic combination of the turbine inlet temperature, the recuperation rate and the pressure ratio. The new microturbine design aims to achieve significantly increased performance within the range of microturbines and even competing with the efficiencies achieved in large industrial gas turbines. The simulated electrical efficiency is 45%. Improving the efficiency of combined heat and power (CHP) systems will significantly decrease the emissions and operating costs of decentralized heat and electricity production. Cost-effective, compact and environmentally friendly micro-and small-scale CHP turbine systems with high electrical efficiency will have an opportunity to successfully compete against reciprocating engines, which today are used in heat and power generation all over the world and manufactured in large production series. This paper presents a small-scale gas turbine process, capable of competing with reciprocating engine in terms of electrical efficiency.

Increased profitability and efficiency by improving the Meetings & Events Category S2P-process – Case Company

The purpose of this research was to examine the most optimal way to arrange meetings and events management and source to pay –process in a global company. The research is a qualitative multi-method case study and is a commission from a global company. The theoretical framework of this research structures around two approaches. First approach focus on a purchasing strategy and management that shows the current role of procure-ment and introduce different ways to organize purchasing functions. Second approach focus on purchasing process management and improvement methods. Annual spend analyze, external and internal interviews and internal survey were done to gain compre-hensive knowledge about the current state of operations and possible solutions. Gathered data were then combined to theoretical framework in order to create optimal solution for the case company. Based on the research a source to pay –process and global policy for meeting and event category was created. The solution includes all relevant matters that are needed in order to secure efficient and profitable operations. The results show that optimal way to arrange meetings and events structures around standardized source to pay –processes, central-ized procurement, preferred supplier and clearly defined roles and responsibilities be-tween different stakeholders.

Evaluation of the Efficiency of Line-Start Permanent-Magnet Machines as a Function of the Operating Temperature

The standard squirrel-cage induction machine has nearly reached its maximum efficiency. In order to further increase the energy efficiency of electrical machines, the use of permanent magnets in combination with the robust design and the line start capability of the induction machine is extensively investigated. Many experimental designs have been suggested in literature, but recently, these line-start permanent-magnet machines (LSPMMs) have become off-the-shelf products available in a power range up to 7.5 kW. The permanent magnet flux density is a function of the operating temperature. Consequently, the temperature will affect almost every electrical quantity of the machine, including current, torque, and efficiency. In this paper, the efficiency of an off-the-shelf 4-kW three-phase LSPMM is evaluated as a function of the temperature by both finite-element modeling and by practical measurements. In order to obtain stator, rotor, and permanent magnet temperatures, lumped thermal modeling is used.

Energy Efficiency in Electrical Drive Systems: Technical potentials, barriers and policy approaches for small and medium industries in Ghana

Today industries and commerce in Ghana are facing enormous energy challenge. The pressure is on for industries to reduce energy consumption, lower carbon emissions and provide se-cured power supply. Industrial electric motor energy efficiency improvement is one of the most important tools to reduce global warming threat and reduce electricity bills. In order to develop a strategic industrial energy efficiency policy, it is therefore necessary to study the barriers that inhibit the implementation of cost – effective energy efficiency measures and the driving forces that promote the implementation. The aim of this thesis is to analyse the energy consumption pattern of electric motors, study factors that promote or inhibit energy efficiency improvements in EMDS and provide cost – effective solutions that improve energy efficiency to bridge the existing energy efficiency gap in the surveyed industries. The results from this thesis has revealed that, the existence of low energy efficiency in motor-driven systems in the surveyed industries were due to poor maintenance practices, absence of standards, power quality issues, lack of access to capital and limited awareness to the im-portance of energy efficiency improvements in EMDS. However, based on the results pre-sented in this thesis, a policy approach towards industrial SMEs should primarily include dis-counted or free energy audit in providing the industries with the necessary information on potential energy efficiency measures, practice best motor management programmes and estab-lish a minimum energy performance standard (MEPS) for motors imported into the country. The thesis has also shown that education and capacity development programmes, financial incentives and system optimization are effective means to promote energy efficiency in elec-tric motor – driven systems in industrial SMEs in Ghana

Improvement of Energy Efficiency in a Gold Mining Industry: Case Study of a Russian Gold Mining Company

The issue of energy efficiency is attracting more and more attention of academia, business and policy makers worldwide due to increasing environmental concerns, depletion of non-renewable energy resources and unstable energy prices. The significant importance of energy efficiency within gold mining industry is justified by considerable energy intensity of this industry as well as by the high share of energy costs in the total operational costs. In the context of increasing industrial energy consumption energy efficiency improvement may provide significant energy savings and reduction of CO2 emission that is highly important in order to contribute to the global goal of sustainability. The purpose of this research is to identify the ways of energy efficiency improvement relevant for a gold mining company. The study implements single holistic case study research strategy focused on a Russian gold mining company. The research involves comprehensive analysis of company’s energy performance including analysis of energy efficiency and energy management practices. This study provides following theoretical and managerial contributions. Firstly, it proposes a methodology for comparative analysis of energy performance of Russian and foreign gold mining companies. Secondly, this study provides comprehensive analysis of main energy efficiency challenges relevant for a Russian gold mining company. Finally, in order to overcome identified challenges this research conceives a guidance for a gold mining company for implementation of energy management system based on the ISO standard.

Energy efficiency of glassmaking production

Master’s thesis Energy efficiency of glassmaking production gives description of glassmaking production and possible energy saving measures. Due to the high electricity and fuel prices the problem of rational energy utilization rises sharply. In addition the environmental issues also require a great attention. This work represented the feasible increasing of the furnace efficiency as the most productive activity. Thesis also provides a detail description of utilizing waste heat boiler. Also possible boiler characteristics are calculated and represented at the end of the thesis. As well as brief description of the feasibility of using this method of energy saving. The solution of this problem has a huge importance. Due to the increasing of energy costs and limits of raw materials, glassmaking industry should overcome on high efficiency operation mode. Especially, if such measures is making a significant contribution in the safety of environment.