ISOPOLYMOLYBDIC ACID-POLY(4-VINYL)PYRIDINE FILM MODIFIED ELECTRODE

Electrochemical polymerization of 4-vinylpyridine produced a uniform poly(4-vinyl)pyridine(PVP) film on the glassy carbon (GC) electrode surface. The isopolymolybdic acid-PVP film-modified electrode was prepared by soaking the PVP/GC electrode in the 0.05 M H2SO4 aqueous solution containing 0.005 M isopolymolybdic acid (H4Mo8O26). The latter (catalyst) is incorporated and held in the PVP film electrostatically. The electrochemical behavior and electrocatalytic properties of this H4Mo8O26-PVP/GC electrode was described. The results indicate that this modified electrode has good stability and electrocatalytic activity on the reduction of chlorate and bromate ions in aqueous solution. The catalytic process is regarded as an EC mechanism.

MUTUAL ENTANGLEMENTS IN POLY(VINYL ACETATE) POLY(METHYL ACRYLATE) INTERPENETRATING POLYMER NETWORKS

An equation has been derived for the equilibrium swelling of sequential interpenetrating polymer networks (IPNs), which exhibit a single glass transition temperature and the two components are considered to be compatible. The properties of the equilibrium swelling and elastic modulus of sequential poly(vinyl acetate)/poly(methyl acrylate) IPNs have been discussed according to the derived equation and the Siegfried-Thomas-Sperling formula of the elastic modulus for homo IPNs. In both fully swollen and bulk states, there was favourable evidence for added physical crosslinks in poly(vinyl acetate)/poly(methyl acrylate) IPNs. The Binder-Frisch theory is also discussed.

DOPING EFFECTS ON THE POLYMER-CHAIN STRUCTURE OF POLY(3-METHYLTHIOPHENE)

The C=C stretching Raman shifts and photoluminescence (PL) for poly(3-methylthiophene) (P3MT) are measured at various doping levels by in situ electrochemical Raman and PL spectroscopic techniques. It is found that the doping for P3MT induces the nonlinear excitations (soliton, Polaron, bipolaron), but also affects the polymer-chain structure, including the conjugated length and the interchain distance.

INSITU CONDUCTIVITY ELECTROCHEMISTRY OF CONDUCTIVE POLYMERS - POLY(3-METHYLTHIOPHENE) AND POLYTHIOPHENE

In situ monitoring of conductivity and potential response of conductive polymers during electrochemical process had been described. A renewable carbon fibre array ring-glassy carbon disk electrode was used for this purpose. Poly(3-methylthiophene) and polythiophene were investigated with this method, and some 5 orders in magnitude of conductivity changes were observed during the electrochemical redox process.

ELECTROCHEMICAL STABILITY AND ELECTROCATALYSIS BEHAVIORS OF POLY(3-METHYLTHIOPHENE) THIN-FILM MODIFIED ELECTRODES

The Electrochemical stability of poly(3-methylthiophene) (PMT) thin film modified glassy carbon electrodes was investigated experimentally with successive cyclic voltammetry(CV) The effects of electrolyte solutions on the stability were studied. In the presence of small hydrated anions (less-than-or-equal-to 3.5nm) in the solution, the electroactivity of PMT films decreased with the characteristics of second order kinetics. In a solution with large hydrated anions (greater-than-or-equal-to 4 nm), PMT films have good stability. PMT/GO electrode can electrocatalyse the oxidation of Br- and Cl- anions, and loses its electroactivity rapidly. X-ray photoelectron spectra (XPS) have demonstrated that chlorine has bonded covalently onto the PMT structure after OV cycles in NaCl solutions.

RELATIONSHIP BETWEEN CRYSTALLIZATION OF THE PDMS BLOCK AND MORPHOLOGY OF POLY(BUTADIENE-B-DIMETHYLSILOXANE)

Studies using transmission electron microscopy, differential scanning calorimetry, and X-ray diffraction showed correlations between the crystallization behavior of the polydimethylsiloxane (PDMS) block and the morphology of the block copolymer poly (butadiene-b-dimethylsiloxane) (PB-PDMS). When the PDMS component existed as spheres dispersed in a PB matrix, the crystallization rate of the PDMS block was lower than when the PDMS phase existed in rod or cylinder form.

TENSILE PROPERTIES OF BLENDS OF PHENOLPHTHALEIN POLY(ETHER ETHER KETONE) WITH A POLY(ETHER IMIDE)

Blends of phenolphthalein poly(ether ether ketone) (PEK-C) with a poly(ether imide) (PEI) in various proportions were prepared by the coprecipitation method. Mechanical properties and morphology of the blends were studied using tensile tests and scanning electron microscopy (SEM). It was found that the tensile moduli exhibit positive deviations from simple additivity. Marked positive deviations were also observed for ultimate strength. These results suggest that the PEI/PEK-C blends are mechanically compatible. SEM study shows no evidence of phase separation, supporting the idea that the blends are compatible.

CRYSTALLIZATION KINETICS OF MIXTURES OF POLY(EPSILON-CAPROLACTONE) AND POLY(STYRENE-CO-ACRYLONITRILE)

The crystallization kinetics in mixtures of poly(epsilon-caprolactone) (PCL) and poly(styrene-co-acrylonitrile) (SAN) has been investigated as the function of composition and crystallization temperature. The isothermal growth rates of PCL spherulites decrease with increasing concentration of SAN. Because of the miscibility of PCL/SAN mixtures, the radial growth rates of the spherulites are described by a kinetic equation including the interaction parameter and the free energy for the formation of crystal nuclei. The interaction parameter obtained from the fitting of the kinetic equation with experimental data is in good agreement with that obtained from melting point depression. Folding surface free energies decrease with the increase of SAN concentration. In light of these results, it is suggested that, for the PCL/SAN mixtures, the noncrystallizable SAN polymer reduces the mobility of crystallizable PCL polymer so that the growth rates decrease with the increase of noncrystallizable component fraction.

PHASE-SEPARATION IN ANHYDRIDE-CURED EPOXY-RESIN CONTAINING PHENOLPHTHALEIN POLY(ETHER ETHER KETONE)

Dynamic mechanical analysis and scanning electron microscopy were used to study phase separation of three blends of anhydride-cure bisphenol-A-type epoxy resin with phenolphthalein poly(ether ether ketone). Phase separation was observed for all the blends. The overall compatibility and the resulting morphology of the cured blends are dependent on the choice of cure agent. The phenomena have been discussed from the points of view of both thermodynamics and kinetics. The effects of the choice of hardener on phase separation are considered to be primarily due to differences between the chemical natures of the hardeners.

DYNAMIC SCALING AND FRACTAL BEHAVIOR OF SPINODAL PHASE-SEPARATION IN POLYMER MIXTURES OF POLY(METHYL METHACRYLATE) WITH POLY(STYRENE-CO-ACRYLONITRILE)

Dynamic scaling and fractal behaviour of spinodal phase separation is studied in a binary polymer mixture of poly(methyl methacrylate) (PMMA) and poly(styrene-co-acrylonitrile) (SAN). In the later stages of spinodal phase separation, a simple dynamic scaling law was found for the scattering function S(q,t):S(q,t) approximately q(m)-3S approximately (q/q(m)). The possibility of using fractal theory to describe the complex morphology of spinodal phase separation is discussed. In phase separation, morphology exhibits strong self-similarity. The two-dimensional image obtained by optical microscopy can be analysed within the framework of fractal concepts. The results give a fractal dimension of 1.64. This implies that the fractal structure may be the reason for the dynamic scaling behaviour of the structure function.

DYNAMIC SCALING OF THE STRUCTURE-FUNCTION FOR SPINODAL DECOMPOSITION IN CRITICAL AND NONCRITICAL MIXTURES OF POLY(VINYL ACETATE) POLY(METHYL METHACRYLATE)

The dynamics of phase separation in a binary polymer blend of poly(vinyl acetate) with poly(methyl methacrylate) was investigated by using a time-resolved light-scattering technique. In the later stages of spinodal decomposition, a simple dynamic scaling law was found for the scattering function S(q, t)(S(q, t) approximately I(q, t)): S(q, t)q(m)-3 S approximately (q/q(m)). The scaling function determined experimentally was in good agreement with that predicted by Furukawa, S approximately (X) approximately X2/(3 + X8) for critical concentration, and approximately in agreement with that predicted by Furukawa, S approximately (X) approximately X2/(3 + X6) for non-critical mixtures. The light-scattering invariant shows that the later stages of the spinodal decomposition were undergoing domain ripening.

EPITAXIAL CRYSTALLIZATION OF TRANS-1,4-POLYBUTADIENE ON HIGHLY ORIENTED ISOTACTIC POLY(PROPYLENE) FILMS

Epitaxial crystallization of trans-1,4-polybutadiene (PBD) on highly oriented isotactic poly(propylene) (iPP) has been investigated at different crystallization temperatures and rates. From electron microscopy and electron diffraction, it is confirmed that epitactic growth of the low-temperature modification (monoclinic) with microcrystals of PBD on the iPP films takes place with their chain directions about +/- 50-degrees apart. No epitaxial relationship occurs between the high-temperature modification (hexagonal) of PBD and the iPP substrate. Thermal analyses of PBD-PP layered films indicate that the epitaxy has an important effect on the formation of the high-temperature modification of PBD.

THE RING-BANDED SPHERULITE STRUCTURE OF POLY(EPSILON-CAPROLACTONE) IN ITS MISCIBLE MIXTURES WITH POLY(STYRENE-CO-ACRYLONITRILE)

The structure of the PCL spherulite in poly(epsilon-caprolactone)/poly(styrene-co-acrylonitrile) (PCL/SAN) blends was investigated by optical microscopy and small angle light scattering. The spherulite structure with a Maltese cross has been observed in pure PCL. Similar PCL/SAN blends exhibited not only spherulites with a Maltese cross, but also distinct extinction rings. The H(v) light scattering pattern especially caused diffraction rings in PCL/SAN blends but not in pure PCL. The spherical symmetry of spherulite PCL becomes more incomplete and the twist of the lamella becomes more irregular with increasing SAN content. It is found that the spherulite structure of PCL/SAN blends is dependent on the crystallization temperature and the concentration of SAN in PCL/SAN blends.

MISCIBILITY OF POLY(N-VINYL-2-PYRROLIDONE) WITH A COPOLYAMIDE

Blends of poly(N-vinyl-2-pyrrolidone) (PVP) with a copolyamide (CoPA) randomly composed of 1:1:1 (wt) nylon 6, nylon 66 and nylon 610 structural units were prepared by casting from a common solvent. They were found to be miscible and show a single, composition-dependent glass transition temperature (T(g)). The addition of PVP to CoPA significantly lowers the crystallinity owing to an increasing T(g) of the system. The observed miscibility is proposed to be the result of specific interactions between the proton acceptor groups of PVP and the amide groups of CoPA.

CONFORMATION OF PHENYL RINGS IN THE HELICAL CHAIN POLYMER POLY(TRIPHENYLMETHYL METHACRYLATE)

The conformation of phenyl rings in the side groups of the helical chain polymer poly(tripenyl-methyl methacrylate) (1) in solution was studied by spectroscopic methods. According to the Raman spectrum the phenyl rings of 1 and triphenylmethyl methacrylate in solution have the same depolarization ratio at 1002 cm-1. The electronic spectra (ultraviolet and fluorescence) of 1 are similar to those of model substances, except for the "red shift" of the spectra of about 5 nm. It was concluded that the phenyl rings can rotate around the phenyl-C bond.