Preparation and characterization of micro and nano fiber reinforced natural rubber composites by latex stage processing

Use of short fibers as reinforcing fillers in rubber composites is on an increasing trend. They are popular due to the possibility of obtaining anisotropic properties, ease of processing and economy. In the preparation of these composites short fibers are incorporated on two roll mixing mills or in internal mixers. This is a high energy intensive time consuming process. This calls for developing less energy intensive and less time consuming processes for incorporation and distribution of short fibers in the rubber matrix. One method for this is to incorporate fibers in the latex stage. The present study is primarily to optimize the preparation of short fiber- natural rubber composite by latex stage compounding and to evaluate the resulting composites in terms of mechanical, dynamic mechanical and thermal properties. A synthetic fiber (Nylon) and a natural fiber (Coir) are used to evaluate the advantages of the processing through latex stage. To extract the full reinforcing potential of the coir fibers the macro fibers are converted to micro fibers through chemical and mechanical means. The thesis is presented in 7 chapters

Numerical Simulation of Two-Part Underwater Towing System

The motion instability is an important issue that occurs during the operation of towed underwater vehicles (TUV), which considerably affects the accuracy of high precision acoustic instrumentations housed inside the same. Out of the various parameters responsible for this, the disturbances from the tow-ship are the most significant one. The present study focus on the motion dynamics of an underwater towing system with ship induced disturbances as the input. The study focus on an innovative system called two-part towing. The methodology involves numerical modeling of the tow system, which consists of modeling of the tow-cables and vehicles formulation. Previous study in this direction used a segmental approach for the modeling of the cable. Even though, the model was successful in predicting the heave response of the tow-body, instabilities were observed in the numerical solution. The present study devises a simple approach called lumped mass spring model (LMSM) for the cable formulation. In this work, the traditional LMSM has been modified in two ways. First, by implementing advanced time integration procedures and secondly, use of a modified beam model which uses only translational degrees of freedoms for solving beam equation. A number of time integration procedures, such as Euler, Houbolt, Newmark and HHT-α were implemented in the traditional LMSM and the strength and weakness of each scheme were numerically estimated. In most of the previous studies, hydrodynamic forces acting on the tow-system such as drag and lift etc. are approximated as analytical expression of velocities. This approach restricts these models to use simple cylindrical shaped towed bodies and may not be applicable modern tow systems which are diversed in shape and complexity. Hence, this particular study, hydrodynamic parameters such as drag and lift of the tow-system are estimated using CFD techniques. To achieve this, a RANS based CFD code has been developed. Further, a new convection interpolation scheme for CFD simulation, called BNCUS, which is blend of cell based and node based formulation, was proposed in the study and numerically tested. To account for the fact that simulation takes considerable time in solving fluid dynamic equations, a dedicated parallel computing setup has been developed. Two types of computational parallelisms are explored in the current study, viz; the model for shared memory processors and distributed memory processors. In the present study, shared memory model was used for structural dynamic analysis of towing system, distributed memory one was devised in solving fluid dynamic equations.

Growth enhancement of micro algae, Chaetoceros calcitrans and Nannochloropsis oculata, using selected bacterial strains

In natural systems phytoplankton interact with planktonic (free living) and attached epiphytic bacteria both synergistically and antagonistically. The specificity of the association with micro algae and bacteria differs in terms of adhesion mechanisms and metabolic cooperation. Present research was carried out to study the effect of bacterial isolates namely Bacillus sp. and Pseudomonas sp. from algal culture systems on the growth of micro algae such as Chaetoceros calcitrans and Nannochloropsis oculata. C. calcitrans (F= 15.34; P<0.05) and N. oculata (F=12.52; P<0.05) showed significantly higher growth, in treatments with Bacillus sp. and Pseudomonas sp when compared to control.

Agent Based Simulation of Street Robbery

Routine activity theory introduced by Cohen& Felson in 1979 states that criminal acts are caused due to the presenceof criminals, vic-timsand the absence of guardians in time and place. As the number of collision of these elements in place and time increases, criminal acts will also increase even if the number of criminals or civilians remains the same within the vicinity of a city. Street robbery is a typical example of routine ac-tivity theory and the occurrence of which can be predicted using routine activity theory. Agent-based models allow simulation of diversity among individuals. Therefore agent based simulation of street robbery can be used to visualize how chronological aspects of human activity influence the incidence of street robbery.The conceptual model identifies three classes of people-criminals, civilians and police with certain activity areas for each. Police exist only as agents of formal guardianship. Criminals with a tendency for crime will be in the search for their victims. Civilians without criminal tendencycan be either victims or guardians. In addition to criminal tendency, each civilian in the model has a unique set of characteristicslike wealth, employment status, ability for guardianship etc. These agents are subjected to random walk through a street environment guided by a Q –learning module and the possible outcomes are analyzed

Agent Based Evacuation Simulation Using Leader-Follower Model

Agent based simulation is a widely developing area in artificial intelligence.The simulation studies are extensively used in different areas of disaster management. This work deals with the study of an agent based evacuation simulation which is being done to handle the various evacuation behaviors.Various emergent behaviors of agents are addressed here. Dynamic grouping behaviors of agents are studied. Collision detection and obstacle avoidances are also incorporated in this approach.Evacuation is studied with single exits and multiple exits and efficiency is measured in terms of evacuation rate, collision rate etc.Net logo is the tool used which helps in the efficient modeling of scenarios in evacuation

Photoluminescence Studies Of Microwave Assisted Synthesized Zno Micro Structures

ZnO micro particles in the range 0.4-0.6 μm were synthesized by microwave irradiation method. The XRD analysis reveals that the sample is in the wurtzite phase with orientation along the (101) plane. SAED pattern of the sample reveals the single crystalline nature of the micro grains. TEM images show the formation of cylindrical shaped ZnO micro structures with hexagonal faces. The optical phonon modes were slightly shifted in the Raman spectrum,attributed to the presence of various crystalline defects and laser induced local heating at the grain boundaries. A broad transmission profile was observed in the FTIR spectrum from 1550-3400 cm-1 which falls in the atmospheric transparency window region. PL spectrum centered at 500 nm with a broad band in the region 420-570 nm comprised of different emission peaks attributed to transition between defect levels. Various emission levels in the sample were expliained with a band diagram

Learning From Cross Country Experiences In Housing: A Micro Finance Approach For Inclusive Housing In India

Housing is one of the primary human needs. It is second only to the need for food and clothing. From a macro perspective, housing is an industry that can prove itself to be a growth engine for a nation, particularly a developing nation like India. Housing has been one of the top priorities for the various governments in India since the seventies. The need for housing has been increasing at a phenomenal pace in India and so also the need for housing finance. Since the growth in supply of housing could not keep pace with the growth in its demand, housing shortage has been on the rise over the years. Housing finance industry which was relatively dormant till the early nineties underwent sweeping changes ever since the initiation of financial sector deregulation measures. Financial deregulation measures brought about several changes in this industry, the first and foremost being the fast growth rate in the industry coupled with cutthroat competition among the industry players. This trend has been quite prominent since the entry of commercial banks into this arena. Accordingly, there has been a surge in the growth of retail (personal) loans segment, particularly in respect of housing loans. This is evident from the fact that housing loans disbursed by banks as a percentage of their total loans has increased from just 2.79% as of end-March 1997 to as high as 12.52% as of end-March 2007. Thus, there has been an unprecedented growth rate in the disbursement of housing loans by banks, and as of 31 March 2007 the outstanding balance of housing loans by all banks in India stands at Rs.230689 Crore, as against just Rs.7946 Crore as of 31 March 1997, the growth rate being 35.82 %CAGR (for the eleven years’ period, FY 1997-‘2007). However, in spite of the impressive growth in housing finance over the years, there are growing apprehensions regarding its inclusiveness, i.e. accessibility to the common man, the underprivileged sections of the society to housing finance etc. Of late, it is widely recognized that formal housing finance system, particularly the commercial banks (CBs) – most dominant among the players – is fast becoming exclusive in operations, with nearly 90% of the total housing credit going to the rich and upper middle income group, primarily the salaried class. The case of housing finance companies (HFCs) is quite similar in this regard. The poor and other marginalized sections are often deprived of adequate credit facilities for housing purpose. Studies have revealed that urban housing poverty is much more acute than the rural probably because of the very fast process of urbanization coupled with constant rural to urban migration

Barriers Faced By Micro, Small And Medium Enterprises In Raising Finance

Worldwide, Micro, Small and Medium Enterprises (MSMEs) have been accepted as an engine of economic growth and for promoting equitable development. In developing countries including India, Micro, Small and Medium Enterprises sector constitute an important part in its development. In spite of this importance, this sector face number of constraints like absence of adequate and timely supply of bank finance, difficulties in procuring raw materials, marketing and distribution challenges and non availability of suitable technology. Review of literature found that there exists problem in accessing finance from banks and financial institutions and this problem may differ from region to region, between sectors, or between individual enterprises within a sector. This paper tries to identify the various barriers faced by these units in raising finance and also try to identify the various sources of finance other than banks. The study is based upon the primary data collected from the 200 MSMEs owners in Kozhikode District of Kerala. The data has been analysed with the help of percentage. The study attempts to submit some recommendations to enhance the overall credit accessibility to MSMEs sector

Some Aspects of Domain Specific Conceptual Modeling for Simulation of Logistic Terminal Operations

When simulation modeling is used for performance improvement studies of complex systems such as transport terminals, domain specific conceptual modeling constructs could be used by modelers to create structured models. A two stage procedure which includes identification of the problem characteristics/cluster - ‘knowledge acquisition’ and identification of standard models for the problem cluster – ‘model abstraction’ was found to be effective in creating structured models when applied to certain logistic terminal systems. In this paper we discuss some methods and examples related the knowledge acquisition and model abstraction stages for the development of three different types of model categories of terminal systems

Modelling and simulation of a photovoltaic fuel cell hybrid system

A stand-alone power system is an autonomous system that supplies electricity to the user load without being connected to the electric grid. This kind of decentralized system is frequently located in remote and inaccessible areas. It is essential for about one third of the world population which are living in developed or isolated regions and have no access to an electricity utility grid. The most people live in remote and rural areas, with low population density, lacking even the basic infrastructure. The utility grid extension to these locations is not a cost effective option and sometimes technically not feasible. The purpose of this thesis is the modelling and simulation of a stand-alone hybrid power system, referred to as “hydrogen Photovoltaic-Fuel Cell (PVFC) hybrid system”. It couples a photovoltaic generator (PV), an alkaline water electrolyser, a storage gas tank, a proton exchange membrane fuel cell (PEMFC), and power conditioning units (PCU) to give different system topologies. The system is intended to be an environmentally friendly solution since it tries maximising the use of a renewable energy source. Electricity is produced by a PV generator to meet the requirements of a user load. Whenever there is enough solar radiation, the user load can be powered totally by the PV electricity. During periods of low solar radiation, auxiliary electricity is required. An alkaline high pressure water electrolyser is powered by the excess energy from the PV generator to produce hydrogen and oxygen at a pressure of maximum 30bar. Gases are stored without compression for short- (hourly or daily) and long- (seasonal) term. A proton exchange membrane (PEM) fuel cell is used to keep the system’s reliability at the same level as for the conventional system while decreasing the environmental impact of the whole system. The PEM fuel cell consumes gases which are produced by an electrolyser to meet the user load demand when the PV generator energy is deficient, so that it works as an auxiliary generator. Power conditioning units are appropriate for the conversion and dispatch the energy between the components of the system. No batteries are used in this system since they represent the weakest when used in PV systems due to their need for sophisticated control and their short lifetime. The model library, ISET Alternative Power Library (ISET-APL), is designed by the Institute of Solar Energy supply Technology (ISET) and used for the simulation of the hybrid system. The physical, analytical and/or empirical equations of each component are programmed and implemented separately in this library for the simulation software program Simplorer by C++ language. The model parameters are derived from manufacturer’s performance data sheets or measurements obtained from literature. The identification and validation of the major hydrogen PVFC hybrid system component models are evaluated according to the measured data of the components, from the manufacturer’s data sheet or from actual system operation. Then, the overall system is simulated, at intervals of one hour each, by using solar radiation as the primary energy input and hydrogen as energy storage for one year operation. A comparison between different topologies, such as DC or AC coupled systems, is carried out on the basis of energy point of view at two locations with different geographical latitudes, in Kassel/Germany (Europe) and in Cairo/Egypt (North Africa). The main conclusion in this work is that the simulation method of the system study under different conditions could successfully be used to give good visualization and comparison between those topologies for the overall performance of the system. The operational performance of the system is not only depending on component efficiency but also on system design and consumption behaviour. The worst case of this system is the low efficiency of the storage subsystem made of the electrolyser, the gas storage tank, and the fuel cell as it is around 25-34% at Cairo and 29-37% at Kassel. Therefore, the research for this system should be concentrated in the subsystem components development especially the fuel cell.

Modellierung und numerische Simulation der Thermoregulation von Früh- und Neugeborenen

Bei frühgeborenen Säuglingen spielt die Thermoregulation zur Aufrechterhaltung einer überlebenswichtigen Körpertemperatur durch Wärmeproduktion, -abgabe bzw. -aufnahme eine entscheidende Rolle. Der Einsatz moderner Inkubatoren soll die körpereigenen Thermoregulatoren unterstützen, und es ist im Hinblick auf verschiedene medizinische Fragestellungen wünschenswert, diesen Prozess modellieren zu können. Wir stellen ein einfaches Modell auf der Basis von partiellen Differentialgleichungen vor und beschreiben detailliert die numerische Simulation mit Hilfe einer Finite-Volumen-Methode. Dazu wird ein zweidimensionales Modell eines Frühgeborenen trianguliert und das Modell diskretisiert. Zahlreiche numerische Resultate zeigen die Qualität unseres Modells.

Lithography-free micro- and nanostructuring based on conventional plasma etching

In now-a-days semiconductor and MEMS technologies the photolithography is the working horse for fabrication of functional devices. The conventional way (so called Top-Down approach) of microstructuring starts with photolithography, followed by patterning the structures using etching, especially dry etching. The requirements for smaller and hence faster devices lead to decrease of the feature size to the range of several nanometers. However, the production of devices in this scale range needs photolithography equipment, which must overcome the diffraction limit. Therefore, new photolithography techniques have been recently developed, but they are rather expensive and restricted to plane surfaces. Recently a new route has been presented - so-called Bottom-Up approach - where from a single atom or a molecule it is possible to obtain functional devices. This creates new field - Nanotechnology - where one speaks about structures with dimensions 1 - 100 nm, and which has the possibility to replace the conventional photolithography concerning its integral part - the self-assembly. However, this technique requires additional and special equipment and therefore is not yet widely applicable. This work presents a general scheme for the fabrication of silicon and silicon dioxide structures with lateral dimensions of less than 100 nm that avoids high-resolution photolithography processes. For the self-aligned formation of extremely small openings in silicon dioxide layers at in depth sharpened surface structures, the angle dependent etching rate distribution of silicon dioxide against plasma etching with a fluorocarbon gas (CHF3) was exploited. Subsequent anisotropic plasma etching of the silicon substrate material through the perforated silicon dioxide masking layer results in high aspect ratio trenches of approximately the same lateral dimensions. The latter can be reduced and precisely adjusted between 0 and 200 nm by thermal oxidation of the silicon structures owing to the volume expansion of silicon during the oxidation. On the basis of this a technology for the fabrication of SNOM calibration standards is presented. Additionally so-formed trenches were used as a template for CVD deposition of diamond resulting in high aspect ratio diamond knife. A lithography-free method for production of periodic and nonperiodic surface structures using the angular dependence of the etching rate is also presented. It combines the self-assembly of masking particles with the conventional plasma etching techniques known from microelectromechanical system technology. The method is generally applicable to bulk as well as layered materials. In this work, layers of glass spheres of different diameters were assembled on the sample surface forming a mask against plasma etching. Silicon surface structures with periodicity of 500 nm and feature dimensions of 20 nm were produced in this way. Thermal oxidation of the so structured silicon substrate offers the capability to vary the fill factor of the periodic structure owing to the volume expansion during oxidation but also to define silicon dioxide surface structures by selective plasma etching. Similar structures can be simply obtained by structuring silicon dioxide layers on silicon. The method offers a simple route for bridging the Nano- and Microtechnology and moreover, an uncomplicated way for photonic crystal fabrication.

Wechselwirkung von im NANOJET erzeugten Teilchen mit Polymeren und biologischen Objekten

Am Institut für Mikrostrukturtechnologie und Analytik wurde eine neue Technik entwickelt, die neue Anwendungen und Methoden der Mikro- und Nanostrukturierung auf Basis eines neuen Verfahrens erschlossen hat. NANOJET führt über die passive Rastersondenmikroskopie hinaus zu einem vielseitigen, aktiven Bearbeitungswerkzeug auf der Mikro- und Nanometerskala. NANOJET (NANOstructuring Downstream PlasmaJET) ist eine aktive Rasterkraft-Mikroskopie-Sonde. Radikale (chemisch aktive Teilchen, die ein ungepaartes Valenzelektron besitzen) strömen aus dem Ende einer ultradünnen, hohlen Rasterkraftmikroskop-Spitze. Dadurch wird es möglich, über die übliche passive Abtastung einer Probenoberfläche hinausgehend, diese simultan und in-situ durch chemische Reaktionen zu verändern. Die Abtragung von Material wird durch eine chemische Ätzreaktion erreicht. In dieser Arbeit wurde zum größten Teil Photoresist als Substrat für die Ätzexperimente verwendet. Für das Ätzen des Resists wurden die Atome des Fluors und des Sauerstoffs im Grundzustand als verantwortlich identifiziert. Durch Experimente und durch Ergänzung von Literaturdaten wurde die Annahme bestätigt, dass Sauerstoffradikale mit Unterstützung von Fluorradikalen für die hohen erzielten Ätzraten verantwortlich sind. Die Beimischung von Fluor in einem Sauerstoffplasma führt zu einer Verringerung der Aktivierungsenergie für die Ätzreaktion gegenüber Verwendung reinen Sauerstoffs. In weiterer Folge wurde ein Strukturierungsverfahren dargestellt. Hierbei wurden "geformte Kapillaren" (mikrostrukturierte Aperturen) eingesetzt. Die Herstellung der Aperturen erfolgte durch einen elektrochemischen Ätzstop-Prozess. Die typische Größe der unter Verwendung der "geformten Kapillaren" geätzten Strukturen entsprach den Kapillarenöffnungen. Es wurde ein Monte-Carlo Simulationsprogramm entwickelt, welches den Transport der reaktiven Teilchen in der langen Transportröhre simulierte. Es wurde sowohl die Transmission der Teilchen in der Transportröhre und der Kapillare als auch ihre Winkelverteilung nach dem Verlassen der Kapillare berechnet. Das Aspektverhältnis der Röhren hat dabei einen sehr starken Einfluss. Mit einem steigenden Aspektverhältnis nahm die Transmission exponentiell ab. Die geschaffene experimentelle Infrastruktur wurde genutzt, um auch biologische Objekte zu behandeln und zu untersuchen. Hierfür wurde eine neue Methodik entwickelt, die eine dreidimensionale Darstellung des Zellinneren erlaubt. Dies wurde durch die kontrollierte Abtragung von Material aus der Zellmembran durchgeführt. Die Abtragung der Zellmembran erfolgte mittels Sauerstoffradikalen, die durch eine hohle Spitze lokalisiert zum Ort der Reaktion transportiert wurden. Ein piezoresistiver Cantilever diente als Sensor in dem zur Bildgebung eingesetzten RKM. Das entwickelte Verfahren ermöglicht es nun erstmals, schonend Zellen zu öffnen und die innen liegenden Organellen weiter zu untersuchen. Als Nachweis für weitere Verwendungsmöglichkeiten des NANOJET-Verfahrens wurde auch Knochenmaterial behandelt. Die Ergebnisse dieser Experimente zeigen klar, dass das Verfahren für vielfältige biologische Materialien verwendbar ist und somit nun ein weiter Anwendungskreis in der Biologie und Medizin offen steht.

Micro-electromechanical structural design and optimization of vertical cavity photonic devices with wide continuous tuning

Diese Arbeit umfaßt das elektromechanische Design und die Designoptimierung von weit durchstimmbaren optischen multimembranbasierten Bauelementen, mit vertikal orientierten Kavitäten, basierend auf der Finiten Element Methode (FEM). Ein multimembran InP/Luft Fabry-Pérot optischer Filter wird dargestellt und umfassend analysiert. In dieser Arbeit wird ein systematisches strukturelles Designverfahren dargestellt. Genaue analytische elektromechanischer Modelle für die Bauelemente sind abgeleitet worden. Diese können unschätzbare Werkzeuge sein, um am Anfang der Designphase schnell einen klaren Einblick zur Verfügung zu stellen. Mittels des FEM Programms ist der durch die nicht-lineare Verspannung hervorgerufene versteifende Effekt nachgeforscht und sein Effekt auf die Verlängerung der mechanischen Durchstimmungsstrecke der Bauelemente demonstriert worden. Interessant war auch die Beobachtung, dass die normierte Relation zwischen Ablenkung und Spannung ein unveränderliches Profil hat. Die Deformation der Membranflächen der in dieser Arbeit dargestellten Bauelementformen erwies sich als ein unerwünschter, jedoch manchmal unvermeidbarer Effekt. Es zeigt sich aber, dass die Wahl der Größe der strukturellen Dimensionen den Grad der Membrandeformation im Falle der Aktuation beeinflusst. Diese Arbeit stellt ein elektromechanisches in FEMLAB implementierte quasi-3D Modell, das allgemein für die Modellierung dünner Strukturen angewendet werden kann, dar; und zwar indem man diese als 2D-Objekte betrachtet und die dritte Dimension als eine konstante Größe (z.B. die Schichtdicke) oder eine Größe, welche eine mathematische Funktion ist, annimmt. Diese Annahme verringert drastisch die Berechnungszeit sowie den erforderlichen Arbeitsspeicherbedarf. Weiter ist es für die Nachforschung des Effekts der Skalierung der durchstimmbaren Bauelemente verwendet worden. Eine neuartige Skalierungstechnik wurde abgeleitet und verwendet. Die Ergebnisse belegen, dass das daraus resultierende, skalierte Bauelement fast genau die gleiche mechanische Durchstimmung wie das unskalierte zeigt. Die Einbeziehung des Einflusses von axialen Verspannungen und Gradientenverspannungen in die Berechnungen erforderte die Änderung der Standardimplementierung des 3D Mechanikberechnungsmodus, der mit der benutzten FEM Software geliefert wurde. Die Ergebnisse dieser Studie zeigen einen großen Einfluss der Verspannung auf die Durchstimmungseigenschaften der untersuchten Bauelemente. Ferner stimmten die Ergebnisse der theoretischen Modellrechnung mit den experimentellen Resultaten sehr gut überein.

Ein Beitrag zur Modellierung und Simulation von elektromechanischen Systemen

Die in dieser Arbeit durchgeführten Untersuchungen zeigen, daß es möglich ist, komplexe thermische Systeme, unter Verwendung der thermisch-, elektrischen Analogien, mit PSpice zu simulieren. Im Mittelpunkt der Untersuchungen standen hierbei Strangkühlkörper zur Kühlung von elektronischen Bauelementen. Es konnte gezeigt werden,daß alle Wärmeübertragungsarten, (Wärmeleitung, Konvektion und Wärmestrahlung) in der Simulation berücksichtigt werden können. Für die Berechnung der Konvektion wurden verschiedene Methoden hergeleitet. Diese gelten zum einen für verschiedene Kühlkörpergeometrien, wie z.B. ebene Flächen und Kühlrippenzwischenräume, andererseits unterscheiden sie sich, je nachdem, ob freie oder erzwungene Konvektion betrachtet wird. Für die Wärmestrahlung zwischen den Kühlrippen wurden verschiedenen Berechnungsmethoden entwickelt. Für die Simulation mit PSpice wurde die Berechnung der Wärmestrahlung zwischen den Kühlrippen vereinfacht. Es konnte gezeigt werden, daß die Fehler, die durch die Vereinfachung entstehen, vernachlässigbar klein sind. Für das thermische Verhalten einer zu kühlenden Wärmequelle wurde ein allgemeines Modell entworfen. Zur Bestimmung der Modellparameter wurden verschiedene Meßverfahren entwickelt. Für eine im Fachgebiet Elektromechanik entwickelte Wärmequelle zum Test von Kühlvorrichtungen wurde mit Hilfe dieser Meßverfahren eine Parameterbestimmung durchgeführt. Die Erstellung des thermischen Modells eines Kühlkörpers für die Simulation in PSpice erfordert die Analyse der Kühlkörpergeometrie. Damit diese Analyse weitestgehend automatisiert werden kann, wurden verschiedene Algorithmen unter Matlab entwickelt. Es wurde ein Algorithmus entwickelt, der es ermöglicht, den Kühlkörper in Elementarzellen zu zerlegen, die für die Erstellung des Simulationsmodells benötigt werden. Desweiteren ist es für die Simulation notwendig zu wissen, welche der Elementarzellen am Rand des Kühlkörpers liegen, welche der Elementarzellen an einem Kühlrippenzwischenraum liegen und welche Kühlkörperkanten schräg verlaufen. Auch zur Lösung dieser Aufgaben wurden verschiedene Algorithmen entwickelt. Diese Algorithmen wurden zu einem Programm zusammengefaßt, das es gestattet, unterschiedliche Strangkühlkörper zu simulieren und die Simulationsergebnisse in Form der Temperaturverteilung auf der Montagefläche des Kühlkörpers grafisch darzustellen. Es können stationäre und transiente Simulationen durchgeführt werden. Desweiteren kann der thermische Widerstand des Kühlkörpers RthK als Funktion der Verlustleistung der Wärmequelle dargestellt werden. Zur Verifikation der Simulationsergebnisse wurden Temperaturmessungen an Kühlkörpern durchgeführt und mit den Simulationsergebnissen verglichen. Diese Vergleiche zeigen, daß die Abweichungen im Bereich der Streuung der Temperaturmessung liegen. Das hier entwickelte Verfahren zur thermischen Simulation von Strangkühlkörpern kann somit als gut bewertet werden.