Composition dependency of the glass forming ability (GFA) in Mg—Ni—Si system by mechanical alloying

The pure elemental powder mixtures with the compositions of Mg₆₅Ni_xSi₃₅−_x (x = 10, 20, 25, 33 at.%) were subject to high-energy ball mill, and the structures of the mixtures at different intervals of milling were characterised by X-ray diffraction (XRD). The compositional dependency of the glass forming ability (GFA) in Mg–Ni–Si system was evaluated based on the experimental results and the theoretical calculation. The compositional dependency of GFA in Mg–Ni–Si system can be understood well by comparing the enthalpies of the crystalline and amorphous phases based on the Miedema's theory for the formation enthalpy of alloys. Increasing the Ni/Mg ratio and/or decreasing Si content can improve the amorphous formability. The calculation results might be of great help in optimising the composition with high GFA in Mg–Ni–Si system.

Indentation study on the pressure sensitivity of a ZR-based bulk metallic glass

Spherical indentation test was conducted on as-cast and annealed Zr_41.2Ti_13.8Cu_12.5Ni₁₀Be_22.5 bulk metallic glass, and the evolution of the morphology of the deformation zone of indents upon annealing was investigated. The DSC traces of the as-cast and annealed samples show that the enthalpy change at the glass transition, ΔH, decreases with the increasing of annealing temperature, indicating the reduction of the free volume upon annealing. The morphology of the indents implies a reduced shear band activity in the annealed samples. The included angles (2θ) between two families of shear bands emanating from the edge of spherical indent in the as-cast and the annealed samples were measured to be in the range of 88-79°, which decrease with the increasing of annealing temperature, indicating pressure sensitive plasticity in the as-cast and annealed samples. By Mohr–Coulomb criterion, the pressure sensitive index, α, can be obtained on the basis of the measured 2θ. The sensitivity index increases with increasing temperature, implying an increase of 'atomistic friction' due to the reduction of the free volume upon annealing.

Reduction of fuel consumption in an industrial glass melting furnace

Reduction of fuel consumption in glass melting furnaces can cut the cost of production, and tackle the global warming. This paper presents three independent solutions to reduce the fuel consumption in industrial glass melting furnaces. The solutions include air preheating, raw material preheating, and improving the insulation of combustion space refractory. Energy balance equations are derived and used to identify the effects of each solution. The results indicate that the three solutions reduce the fuel consumption by 9.5%, 17%, and 34%, respectively.

Preliminary observations on the tank and pond culture of the glass eels of the Australian shortfin eel, Anguilla Australis Richardson

There is expanding interest in the culture of the Australian shortfin eel Anguilla australis Richardson; however, there is a lack of fundamental biology and husbandry information necessary to further develop an industry within Australia. The present study was undertaken to gain a preliminary understanding of basic husbandry requirements for rearing of juvenile A. australis (glass eels and elvers) in tanks and earthen ponds. Newly caught glass eels were successfully acclimated to culture conditions. During tank culture trials, specific growth rates (SGR) and survival rates ranged from −2.1 to 2.8% day⁻¹ and 52% to 100% respectively. Glass eels weaned onto a commercial eel diet exhibited a significantly greater SGR and survival rate than those weaned onto a commercial trout diet. Glass eels weaned onto an eel diet over a 15-day period grew slightly faster than eels weaned over a 5-day period, but survival rates were not significantly different for each treatment. SGRs (up to 2.8% day⁻¹) were significantly higher for glass eels fed at 9 and 12% day⁻¹ than at 6% day⁻¹. Stocking densities between 2.5 kg m⁻³ and 30 kg m⁻³ did not influence either SGR or survival rates. SGRs were significantly higher for glass eels cultured at 25 °C than at lower temperatures. During pond culture trials, SGRs and survival rates ranged from 1.36 to 1.65% day⁻¹ and 39% to 77% respectively. The SGR and survival rates of juvenile eels stocked into ponds receiving supplementary feeding with a commercial eel diet were not significantly different to those of eels stocked into ponds that did not receive supplementary feeding.

Decisionmaking in a glass house : mass media, public opinion, and American and European foreign policy in the 21st century

"Decisionmaking in a Glass House: Mass Media, Public Opinion, and American and European Foreign Policy in the 21st Century" edited by Brigitte L. Nacos, Robert Y. Shapiro and Pierangelo Isernia is reviewed.

A novel method of tube manufacture for vehicle crashworthiness utilising the QUICKSTEP™ Process.

A novel method of composite tube manufacture was developed for potential use in automotive crash structures. Tubes were crushed axially under quasi-static conditions and highly repeatable behaviour was observed with an average specific energy absorption of -85kJ/kg. DMTA results indicated that the tubes were fully cured, even when the cycle was reduced to 7 minutes, giving this process huge potential for high-volume production.

Manufacturing process effects on the mode I interlaminar fracture toughness and nanocreep properties of CFRP

Quickstep ™ is a fluid filled floating mould technology which was recently developed by an Australian company of the same name. The Quickstep and conventional autoclave manufacture of composites were compared by investigating the mode I interlaminar fracture toughness and nanocreep propeties of HexPly914 carbon epoxy composites. It was found that composites cured using the Quickstep technology had significantly higher fracture toughness (1.8 times) than the composites cured via autoclave for this system. DMTA (dynamic mechanical thermal analysis) results showed a higher Tg (glass transition temperature) for the material manufactured by the Quickstep than that cured by the autoclave. FTIR (Fourier transform infrared spectroscopy) spectra did not indicate any difference in cure chemistry between the two processes. Nanocreep experiments were performed to explore the viscoelastic properties of the epoxy matrix of composites. The KelvinVoigt three-element model was applied to analyse the indentation creep behaviour of both composites.

Plastic deformation in Zr41 Ti14 Cu12.5 Ni10 Be22.5 bulk metal glass under vickers indenter

Vickers indentation was conducted on an as-cast Zr41Ti14Cu12.5Ni10Be22.5 bulk metal glass (BMG) to study shear band formation using a bonded interface technique. The results indicate that the plastic deformation in the BMG is accommodated by the semi-circular (primary) and radial (secondary) shear bands. The inter-band spacing of the semi-circular shear bands is found to be independent of the applied load. The measured size of the deformation zone is in good agreement with the prediction of the theoretical model proposed by Zhang et al.

Stephen Procter: reflections of a glass artist

Stephen Procter: Reflections of a Glass Artist, records the thoughts and philosophies of the artist and glassmaker who for a number of years headed the Glass Department of the Australian National University School of Art. It traces his career in glass working from his first interest developed through a pointillist technique while living on Dartmoor; through his British Council-funded grant that enabled him to learn glass blowing and cutting techniques in Austria; to the mature landscape paintings and glass sculptures created during his years living in Australia.