Teollisuusvaihteiden kunnossapitopalvelun arvoelementit

Tutkimusongelmana oli tiedon lisääminen teollisuusvaihteiden kunnossapitopal-veluiden asiakasarvon muodostumiseen liittyen. Työn tavoitteena oli arviointi-mallin rakentaminen asiakasarvon osatekijöiden selvittämiseksi sekä niiden tär-keysjärjestykseen saamiseksi. Tutkimusongelmaa lähestyttiin kolmesta teo-rianäkökulmasta: (1) Arvo-käsitteen ja arvoon läheisesti kytköksissä olevista suorituskyvyn osatekijöiden määrittelystä, (2) kunnossapidon merkityksestä ja roolista yrityksen liiketoiminnassa ja (3) asiakas-toimittaja –suhteen merkityk-sestä asiakasarvon muodostumisessa. Teorianäkökulmien pohjalta muodostettiin teollisuusvaihteiden kunnossapidon viitekehykseen sopiva arvohierarkia, jonka osatekijöiden, arvoelementtien, yhteisvaikutuksesta kunnossapitopalvelun asia-kasarvo syntyy. Työn empiriaosuudessa mallia testattiin käytännössä. Hierarkian arvoelementtien tärkeysjärjestyksen ja kaikille asiakkaille yhteisten arvoelementtien löytämiseksi käytettiin Analyyttisen hierarkiaprosessin (AHP) menetelmää osana asiakasryh-mähaastatteluita. Haastattelut toteutettiin täsmäryhmähaastatteluina ja haastatel-tavat ryhmät koostuivat haastatteluihin valittujen asiakkaiden kunnossapidon vastuuhenkilöistä. Tutkimustuloksina havaittiin, että asiakaskohtaiset arvoelementit ja niiden tärke-ysjärjestys saadaan mallin avulla esiin, mutta asiakaskohtaiset erot arvon muo-dostumisessa ovat suuria. Asiakasarvoon vaikuttavien taustatekijöiden, ainakin yhteistyösuhteen tason ja vaihdannan kohteena olevien palveluiden tason, havait-tiin selittävän osaltaan eroja asiakkaiden välillä. Lisäksi teollisen kunnossapidon toimintaympäristön dynaaminen luonne, jossa eri osatekijöiden keskinäiset riip-puvuussuhteet muuttuvat koko ajan, olisi kyettävä huomioimaan myös asia-kasarvon muodostumisen arvioinnissa.

Simulation model of wind turbine gearbox and lubrication system

As increasing efficiency of a wind turbine gearbox, more power can be transferred from rotor blades to generator and less power is used to cause wear and heating in the gearbox. By using a simulation model, behavior of the gearbox can be studied before creating expensive prototypes. The objective of the thesis is to model a wind turbine gearbox and its lubrication system to study power losses and heat transfer inside the gearbox and to study the simulation methods of the used software. Software used to create the simulation model is Siemens LMS Imagine.Lab AMESim, which can be used to create one-dimensional mechatronic system simulation models from different fields of engineering. When combining components from different libraries it is possible to create a simulation model, which includes mechanical, thermal and hydraulic models of the gearbox. Results for mechanical, thermal, and hydraulic simulations are presented in the thesis. Due to the large scale of the wind turbine gearbox and the amount of power transmitted, power loss calculations from AMESim software are inaccurate and power losses are modelled as constant efficiency for each gear mesh. Starting values for simulation in thermal and hydraulic simulations were chosen from test measurements and from empirical study as compact and complex design of gearbox prevents accurate test measurements. In further studies to increase the accuracy of the simulation model, components used for power loss calculations needs to be modified and values for unknown variables are needed to be solved through accurate test measurements.

Nutritional aspects of nile tilapia (Oreochromis niloticus) silage

One third of the world's fishing produce is not directly used for human consumption. Instead, it is used for making animal food or is wasted as residue. It would be ideal to use the raw material thoroughly and to recover by-products, preventing the generation of residues. With the objectives of increasing the income and the production of the industry, as well as minimizing environmental and health problems from fish residue, chemical silage from Tilapia (Oreochromis niloticus) processing residues was developed after homogenization and acidification of the biomass with 3% formic acid: propionic, 1:1, addition of antioxidant BHT and maintenance of pH at approximately 4.0. Analyses to determine the moisture, protein, lipids and ash were carried out. The amino acids were examined in an auto analyzer after acid hydrolysis, except for the tryptophan which was determined through colorimetry. The tilapia silage presented contents that were similar to or higher than the FAO standards for all essential amino acids, except for the tryptophan. The highest values found were for glutamic acid, lysine and leucine. The results indicate a potential use of the silage prepared from the Nile tilapia processing residue as a protein source in the manufacturing of fish food.

Vibration analysis of a power take-off line

Gear rattle is a phenomenon that occurs when idling or lightly loaded gears collide due to engine’s torque fluctuations. This behaviour is related to vibration behaviour of the transmission system. Aim of this master’s thesis is to evaluate Adams and Adams/Machinery as a simulation tools for modelling the rattle e ect in a transmission system. A case study of tractor’s power take-o driveline, suspected to be prone to rattle, is performed in this work. Modelling methods used by Adams in this type of study are presented in the theory section while simulation model build with the software during this work is presented in the results. The Machinery toolbox is used to create gears and bearings while other model components are created with standard Adams tool set. Geometries and excitations are exported from other softwares. Results were obtained from multiple variations of a base model. These result sets and literature review suggest that Adams/Machinery may not be the most suitable tool for rattle analysis. While the system behaviour was partially captured, for accurate modelling user-written routines must be used which may be more easily performed with other tools. Further research about this topic is required.

3D-tulostettu tuuliturbiinin vaihteen pienoismalli

Työn aiheena on vaihteen pienoismallin suunnittelu ja toteutus 3d-tulostusta hyväksi käyttäen. Pienoismalli tehdään Moventas Gears Oy:n suunnittelemasta tuuliturbiinin vaihteesta. Vaihteen pienentämisestä johtuen malliin on suunniteltava uudet laakeripesät ja hammaspyörät. 3D-tulostuksen ja pienoismallin pienen koon ansiosta vaihdetta voidaan yksinkertaistaa suuresti ja näin vähentää tulostettavien osien määrää. Lisäksi työssä selvitetään, mitä ongelmia 3D-tulostus tuo valmistukseen ja suunnitteluun. Työn kirjallisessa osassa selvennetään planeettavaihteen toimintaa yleisesti sekä esitellään Exceed Series 3+ vaihdetta. Lisäksi kerrotaan 3D-tulostuksesta, sen periaatteesta, erilaisista tulostusmenetelmistä, tulostinlaitteesta ja mahdollisista ongelmista tulostuksessa. Kokeellinen osa koostuu pienoismallin suunnittelusta ja valmistuksesta. Valmistuksessa olleiden virheiden takia muutama osa jouduttiin tulostamaan uudelleen. Muutamia osia jouduttiin myös hieman jälkikäsittelemään tulostuksen jälkeen, jotta malli saatiin kasattua. Ongelmakohdaksi muodostui tulostimen ohjelmisto ja tulostustiedostot. Tulostusprosessi sujui kuitenkin hyvin. Lopputuloksena saatiin toimiva pienoismalli. 3D-tulostus toimii hyvin monimutkaisten kappaleiden tulostuksessa. Tulostuksen hinta nousi kuitenkin varsin korkeaksi. Tulostuslaitteistosta riippuen tulostuksen voisi mahdollisesti suorittaa myös halvemmallakin.

Balcony, Davis Community Center and Apartments, Chapman College, Orange, California

Student on balcony with fishing pole at Davis Community Center and Apartments. Nixon/Agnew poster in window--old or another dormitory? Davis opened September, 1974, at 625 North Grand Street, Orange, California, named in honor of Chapman College's fourth president, Dr. John L. Davis.

Henry Hope & Sons of Canada Ltd. Letter, 1916

Henry Hope & Sons of Canada Ltd. were located at 45 King Street West, Toronto, Ont. at the writing of this letter in 1916. The company specialized in “weathertight casements in iron steel or gun-metal, unbreakable steel windows, fanlight opening-gear, leaded lights and stained glass, patent glass roofing, locks and door furniture, rainwater goods in cast lead and cast iron”. The letter is addressed to Mr. H.Y. [Harry Young] Grant, c/o Fenwick Farm, Lundy’s Lane, Niagara Falls, Ont. from R.W. Smith. The letter is in reply to a query about casement windows. Harry Young Grant (1860-1934), son of Sir James Alexander Grant and Maria Malloch of Ottawa, Ont. was a medical doctor specializing in the treatment of the eye, ear, nose and throat. After his retirement he became a member of the Niagara Parks Commission. He was married to Grace A. Smith, daughter of James R. Smith of Buffalo.

Photograph - Dorothy Rungeling's Fifth Plane

A photograph of Dorothy Rungeling inside her fifth and last plane (as written in her scrapbook). The airplane is described as a 1956 Beech Bonanza, 4 seat, retractable gear, 225 Continental engine.

Ontario Forest Industries Association records, 1900-1989, n.d.

The Ontario Forest Industries Association (OFIA) was founded in 1944. It is a provincial trade association that represents member companies who produce a wide range of products, including pulp, paper, paperboard, lumber, panelboard, plywood and veneer. The OFIA works with its member companies to address issues of common interest and concern, and communicates these issues to the appropriate government, industrial or business sector. The Ontario Forest Information Service represented the OFIA from 1951 to 1988 as the publishers of their industry periodicals. Bush News was the first periodical published by the Service for the OFIA and ran until 1964, when it was replaced by Ontario Logger. In 1968, the name was changed to The Logger. In 1970, this was replaced by The Forest Scene. This new periodical was a departure from the earlier versions, which had served primarily as an internal communication system for the industry. The Forest Scene adopted a new format and editorial approach, emphasizing outdoor activities, recreation, hunting and fishing, conservation, and forestry operations and methods, thus appealing to a much wider readership. The Forest Scene ceased publication in 1988.