Fuel consumption of road commercial vehicles in the driving schedule

The fuel consumption is an important factor in the vehicle development due the fact that it has a direct effect on its trade aims. Besides that, it is known that the petrol is a scarce fuel. In this paper it is presented a procedure of fuel consumption calculation for a vehicle traveling in driving schedule. In such calculation it has been taken into account the operational conditions (load, pavement, climbing road, among others) and the building characteristics (map engine, transmission, frontal area, tire, among others) of road vehicles. There has also been an application of the theoretical model developed in a sample Mercedes-Benz do Brasil vehicle which has been compared with the values of experimental tests. Copyright © 1997 Society of Automotive Engineers, Inc.

Modeling of a MIT for the application of a frequency inverter of the electric vehicle

Nowadays, drives that use a combination of induction motors and frequency inverters are very common, a fact due to the financial practicality and viability in purchasing and operating that system. This system modeling and simulation becomes important when it wants to evaluate the performance, to calculate and correct parameters, and it has a fundamental role in functionality and viability analysis for application of new configurations and technologies. This work is about to elaborate a simple induction motor model based in the torque versus speed characteristic, using the linearization method for application in a specific operation range to be controlled by a frequency inverter. © 2011 Springer-Verlag Berlin Heidelberg.

Nasal administration of liquid crystal precursor mucoadhesive vehicle as an alternative antiretroviral therapy

The purpose of this study was to develop a mucoadhesive stimuli-sensitive drug delivery system for nasal administration of zidovudine (AZT). The system was prepared by formulating a low viscosity precursor of a liquid crystal phase, taking advantage of its lyotropic phase behavior. Flow rheology measurements showed that the formulation composed of PPG-5-CETETH-20, oleic acid and water (55, 30, 15% w/w), denominated P, has Newtonian flow behavior. Polarized light microscopy (PLM) revealed that formulation P is isotropic, whereas its 1:1 (w/w) dilution with artificial nasal mucus (ANM) changed the system to an anisotropic lamellar phase (PD). Oscillatory frequency sweep analysis showed that PD has a high storage modulus (G′) at nasal temperatures. Measurement of the mucoadhesive force against excised porcine nasal mucosa or a mucin disk proved that the transition to the lamellar phase tripled the work of mucoadhesion. Ex vivo permeation studies across porcine nasal mucosa exhibited an 18-fold rise in the permeability of AZT from the formulation. The Weibull mathematical model suggested that the AZT is released by Fickian diffusion mechanisms. Hence, the physicochemical characterization, combined with ex vivo studies, revealed that the PPG-5-CETETH-20, oleic acid, and water formulation could form a mucoadhesive matrix in contact with nasal mucus that promoted nasal absorption of the AZT. For an in vivo assessment, the plasma concentrations of AZT in rats were determined by HPLC method following intravenous and intranasal administration of AZT-loaded P formulation (PA) and AZT solution, respectively, at a dose of 8 mg/kg. The intranasal administration of PA resulted in a fast absorption process (Tmax = 6.7 min). Therefore, a liquid crystal precursor formulation administered by the nasal route might represent a promising novel tool for the systemic delivery of AZT and other antiretroviral drugs. In the present study, the uptake of AZT absorption in the nasal mucosa was demonstrated, providing new foundations for clinical trials in patients with AIDS. © 2012 Elsevier B.V. All rights reserved.

Caracterização do transporte rodoviário de bovinos de corte e efeitos no bem-estar animal e na qualidade as carcaças

Pós-graduação em Zootecnia - FCAV

Road maintenance, funds and fund management

This edition of the Bulletin deals with road maintenance, funds and fund management. Among other things, it emphasizes, the need to manage road funds in accordance with clear performance rules which seek to minimize maintenance costs and ensure that the road network is maintained in an appropriate condition.

Road maintenance and international competitiveness

The present and subsequent editions of the Bulletin will deal with the issue of road maintenance, its close connection with transport costs and its impact upon the international competitiveness of the countries of Latin America and the Caribbean. When roads are in poor condition, vehicle operating costs increase by 30 to 50% or even more. Autonomous, adequate and regular funding contributes to effective road maintenance and, consequently, to reducing vehicle operating costs.

Economic Survey of the Caribbean 2013: Improved economic performance with reduced downside risks

Includes bibliography.

Desenvolvimento de um sistema de informações georreferenciadas de segurança viária

Pós-graduação em Ciências Cartográficas - FCT

Estudo preliminar da preferência de cor para rota e seta de manobra em mapas de sistemas de guia de rota

In-Car Navigation System and Route Guidance (RGNS), commercial or free, have adopted different graphic designs to maps which support the navigation task. This paper aims at evaluating the driver's subjective preference for colors to represent route and arrow direction in maps for these systems. A total of 54 drivers (27 males and 27 females) participated in an experiment which was performed in a parked vehicle. Two cartographic representations were produced to evaluate the route color and other two for the arrow color. The route was symbolized by black or blue color and the arrow direction by green or red hue. The cartographic representations were presented in a seven-inch navigation monitor. The results indicate that most drivers prefer the navigation route in black color. However, drivers who regularly use navigation systems have presented the tendency to prefer the route in blue hue. The direction arrow in green hue was the mostly preferred by the drivers and there was no significant correlation between different individual characteristics. This study concludes that drivers' preference was influenced by different factors, such as grouping by color, shape and proximity, subjective or conventional association, as well as by the level of contrast among the map features. Evaluating the performance of cartographic representations in route following task is recommended, in order to support the influence of graphic designs to maps in usability of route guidance systems.

Effects of flunixin meglumine administration on physiological and performance responses of transported feeder cattle

The objective was to evaluate the effects of flunixin meglumine administration on physiological and performance responses of transported cattle during feedlot receiving. Forty-five Angus x Hereford steers were ranked by BW on d 0 and assigned to 1 of 3 treatments:1) transport for 1,280 km in a commercial livestock trailer and administration of flunixin meglumine (1.1 mg/kg BW; intravenous) at loading (d 0) and unloading (d 1; FM), 2) transport for 1,280 km in a commercial livestock trailer and administration of 0.9% saline (0.022 mL/kg BW; intravenous) at loading (d 0) and unloading (d 1; TRANS), or 3) no transport and administration of 0.9% saline (0.022 mL/kg BW; intravenous) concurrently with loading (d 0) and unloading (d 1) of FM and TRANS cohorts (CON). Upon arrival and processing for treatment administration on d 1, steers within each treatment were ranked by BW and assigned to 15 feedlot pens (5 pens/treatment, 3 steers/pen). Full BW was recorded before (d -1 and 0) treatment application and at the end of experiment (d 28 and 29) for ADG calculation. Total DMI was evaluated daily from d 1 to 28. Blood samples were collected on d 0 (before treatment administration), 1 (after unloading but before treatment administration), 4, 7, 10, 14, 21, and 28. Body weight shrink from d 0 to 1 was less (P < 0.01) in CON vs. FM and TRANS but similar (P = 0.94) between TRANS and FM. Mean ADG was greater (P <= 0.04) in CON vs. FM and TRANS but similar (P = 0.69) between TRANS and FM. No treatment effects were detected on DMI, but CON had greater G:F vs. TRANS (P = 0.08) and FM (P = 0.02), whereas G:F was similar (P = 0.68) between TRANS and FM. Mean plasma cortisol concentrations tended (P <= 0.09) to be greater in TRANS vs. FM and CON but was similar (P = 0.87) between CON and FM. Plasma NEFA concentrations were greater (P <= 0.02) for TRANS and FM vs. CON on d 1 and greater (P <= 0.04) for FM vs. TRANS and CON on d 4. Plasma ceruloplasmin concentrations were greater (P <= 0.03) for TRANS vs. CON on d 1, 4, and 7, greater (P <= 0.05) for TRANS vs. FM on d 4 and 7, and greater (P <= 0.04) for FM vs. CON on d 1 and 4. Plasma haptoglobin concentrations were greater (P < 0.01) for TRANS vs. CON and FM on d 1 and 4 and greater (P <= 0.05) for FM vs. CON on d 1 and 4. In conclusion, flunixin meglumine reduced the cortisol and acute-phase protein responses elicited by road transport but did not improve receiving performance of feeder cattle.

Use of nonlinear asymmetrical shock absorber to improve comfort on passenger vehicles

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Safety performance models for urban intersections in Brazil

This paper presents a modeling effort for developing safety performance models (SPM) for urban intersections for three major Brazilian cities. The proposed methodology for calibrating SPM has been divided into the following steps: defining the safety study objective, choosing predictive variables and sample size, data acquisition, defining model expression and model parameters and model evaluation. Among the predictive variables explored in the calibration phase were exposure variables (AADT), number of lanes, number of approaches and central median status. SPMs were obtained for three cities: Fortaleza, Belo Horizonte and Brasilia. The SPM developed for signalized intersections in Fortaleza and Belo Horizonte had the same structure and the most significant independent variables, which were AADT entering the intersection and number of lanes, and in addition, the coefficient of the best models were in the same range of values. For Brasilia, because of the sample size, the signalized and unsignalized intersections were grouped, and the AADT was split in minor and major approaches, which were the most significant variables. This paper also evaluated SPM transferability to other jurisdiction. The SPM for signalized intersections from Fortaleza and Belo Horizonte have been recalibrated (in terms of the COx) to the city of Porto Alegre. The models were adjusted following the Highway Safety Manual (HSM) calibration procedure and yielded C-x of 0.65 and 2.06 for Fortaleza and Belo Horizonte SPM respectively. This paper showed the experience and future challenges toward the initiatives on development of SPMs in Brazil, that can serve as a guide for other countries that are in the same stage in this subject. (C) 2014 Elsevier Ltd. All rights reserved.

Desenvolvimento de um computador de bordo para veículo Baja-SAE

The objective of this paper is show the development of an Eletronic Control Unit (ECU) for Baja-SAE vehicles from its requirements to final implementation. An ECU for Baja-SAE vehicles is made of electric and electronic circuits (appropriated to the hostile situations of an off-road competition) able to make important measurements for the running or stand-by vehicle performance. For this development, some concepts were studied: embedded electronics concepts (mainly microcontrollers and data acquisition circuits) and sensoring. Both the studies were made considering the off-road environment. After these initial studies, the elaboration of the basics hardware and software (under simulations) has begun, and this elaboration objectives maximum performance and low implementation cost. After the theorical studies, basic definition of the hardware and software’s architectures and simulations, the printed circuit boards (PCB) were made, as exhaustive tests in these boards for debugging and verify if the boards work well. Once the system was tested in the university, it ran into a regional Southeast competition in 2010, that definitely proved the efficiency of the whole system

Processamento de peças em materiais compósitos para o projeto BAJA SAE

The weight of a vehicle has always been considered an extreme important factor, because it interferes in the performance, steering, consume, environmental impact, wear of components, among the others. Because of the new demand, consume reduction aim and gases emission increased the necessity to manufacture lighter vehicles, guaranteeing the complying with the gas emission international law. Besides the legal demand, the low weight will certainly be essential for the competitiveness for the next generation of vehicles. It is with this thinking the composite materials have been introduced in the automobilist industry, because those materials show an excellent relation of strength/weight, providing a reduction of consume and the increase of load capacity. Those factors justify the increase of interest of industry and the necessity of optimization of those materials and of their process. For this research, the field of application will be the Baja SAE Project, a project that is fully developed by engineering students, where they build a prototype single seat, off-road category, for use on hilly slopes with obstacle. This research aims to study two key components of the prototype are made of composite materials, analyzing all the processing. In addition, there is the analysis of the viability of this production parts to a Baja SAE vehicle, in order to increase their performance and reduce their weight without reducing the safety and robustness of the prototype. It was possible to achieve weight reduction of the steering subsystem with manufacturing the flywheel hybrid composite (carbon/glass) and the replacement of SAE 1010 steel by hybrid composite (carbon/aramid) in CVT box. The importance of this study is to obtain a good project for the vehicle of technical and scientific manner, contributing to the know-how to the team and providing a basis for optimization for upcoming projects

Avaliação da usabilidade de representações cartográficas em diferentes escalas para sistema de navegação e guia de rota em automóvel

Pós-graduação em Ciências Cartográficas - FCT