Preparation and electrospinning of acidified-oxidized potato starch

This paper investigates the preparation and electrospinning of acidified-oxidized potato starch. In this article, acidified-oxidized potato starch was prepared by adding ammonium persulfate as an oxidizing agent and hydrochloric acid as a catalyst. The effect of reaction time, temperature, the concentration of hydrochloric acid and the content of ammonium persulfate on the viscosity and content of carboxyl were discussed. The optimum reaction conditions were as follows: 1.5 hours ,50℃, 0.5mol/l HCl, 2.5% (NH4)2S2O8. And then, the acidified-oxidized potato starch prepared at the optimum condition was dissolved in dimethyl sulfoxide (DMSO) to be electrospinned by contrast to native starch. Electrospinning of 5wt%-21wt% of modified starch in DMSO produced beads, beaded fibers, and smooth fibers, depending on the concentration range. Smooth fibers were observed until the concentration reached 19wt%, while native starch was 5wt%.

Nanostructured liquid crystalline particles as an alternative delivery vehicle for plant agrochemicals

Agrochemical spray formulations applied to plants are often mixed with surfactants that facilitate delivery of the active ingredient. However, surfactants cause phytotoxicity and off-target effects in the environment. We propose the use of nanostructured liquid crystalline particles (NLCP) as an alternative to surfactant-based agrochemical delivery. For this, we have compared the application of commercial surfactants, di (2-ethylhexyl) sulfosuccinate and alkyl dimethyl betaine, with NLCP made from phytantriol, at concentrations of 0.1%, 1% and 5% on the adaxial surface of leaves of four plant species Ttriticum aestivum (wheat), Zea mays (maize), Lupinus angustifolius (lupin), and Arabidopsis thaliana. In comparison with the application of surfactants there was less phytotoxicity on leaves of each species following treatment with NLCP. Following treatment of leaves with NLCP analysis of cuticular wax micromorphology revealed less wax solubilization in the monocot species. The results clearly show that there are advantages in the use of NLCP rather than surfactants for agrochemical delivery.

Improving peak shapes with counter gradients in two-dimensional high performance liquid chromatography

To achieve the greatest peak capacity in two-dimensional high performance liquid chromatography (2D-HPLC) a gradient should be operated in both separation dimensions. However, it is known that when an injection solvent that is stronger than the initial mobile phase composition is deleterious to peak performance, thus causing problems when cutting a portion from one gradient into another. This was overcome when coupling hydrophilic interaction with reversed phase chromatography by introducing a counter gradient that changed the solvent strength of the second dimension injection. It was found that an injection solvent composition of 20% acetonitrile in water gave acceptable results in one-dimensional simulations with an initial composition of 5% acetonitrile. When this was transferred to a 2D-HPLC separation of standards it was found that a marked improvement in peak shape was gained for the moderately retained analytes (phenol and dimethyl phthalate), some improvement for the weakly retained caffeine and very little change for the strongly retained n-propylbenzene and anthracene which already displayed good chromatographic profiles. This effect was transferred when applied to a 2D-HPLC separation of a coffee extract where the indecipherable retention profile was transformed to a successful application multidimensional chromatography with peaks occupying 71% of the separation space according to the geometric approach to factor analysis.

Investigating retention characteristics of a mixed-mode stationary phase and the enhancement of monolith selectivity for high-performance liquid chromatography

The synthesis and chromatographic behavior of an analytical size mixed-mode bonded silica monolith was investigated. The monolith was functionalized by an in situ modification process of a bare silica rod with chloro(3-cyanopropyl)dimethyl silane and chlorodimethyl propyl phenyl silane solutions. These ligands were selected in order to combine both resonance and nonresonance π-type bonding within a single separation environment. Selectivity studies were undertaken using n-alkyl benzenes and polycyclic aromatic hydrocarbons in aqueous methanol and acetonitrile mobile phases to assess the methylene and aromatic selectivities of the column. The results fit with the linear solvent strength theory suggesting excellent selectivity of the column was achieved. Comparison studies were performed on monolithic columns that were functionalized separately with cyano and phenyl ligands, suggesting highly conjugated molecules were able to successfully exploit both of the π-type selectivities afforded by the two different ligands on the mixed-mode column.

Molecular mechanism of the synergistic effects of vitrification solutions on the stability of phospholipid bilayers

The vitrification solutions used in the cryopreservation of biological samples aim to minimize the deleterious formation of ice by dehydrating cells and promoting the formation of the glassy state of water. They contain a mixture of different cryoprotective agents (CPAs) in water, typically polyhydroxylated alcohols and/or dimethyl sulfoxide (DMSO), which can damage cell membranes. Molecular dynamics simulations have been used to investigate the behavior of pure DPPC, pure DOPC, and mixed DOPC-β-sitosterol bilayers solvated in a vitrification solution containing glycerol, ethylene glycol, and DMSO at concentrations that approximate the widely used plant vitrification solution 2. As in the case of solutions containing a single CPA, the vitrification solution causes the bilayer to thin and become disordered, and pores form in the case of some bilayers. Importantly, the degree of thinning is, however, substantially reduced compared to solutions of DMSO containing the same total CPA concentration. The reduction in the damage done to the bilayers is a result of the ability of the polyhydroxylated species (especially glycerol) to form hydrogen bonds to the lipid and sterol molecules of the bilayer. A decrease in the amount of DMSO in the vitrification solution with a corresponding increase in the amount of glycerol or ethylene glycol diminishes further its damaging effect due to increased hydrogen bonding of the polyol species to the bilayer headgroups. These findings rationalize, to our knowledge for the first time, the synergistic effects of combining different CPAs, and form the basis for the optimization of vitrification solutions. © 2014 Biophysical Society.

Effect of zwitterions on electrochemical properties of oligoether-based electrolytes

Solid polymer electrolytes show great potential in electrochemical devices. Poly(ethylene oxide) (PEO) has been studied as a matrix for solid polymer electrolytes because it has relatively high ionic conductivity. In order to investigate the effect of zwitterions on the electrochemical properties of poly(ethylene glycol) dimethyl ether (G5)/lithium bis(fluorosulfonyl) amide (LiFSA) electrolytes, a liquid zwitterion (ImZ2) was added to the G5-based electrolytes. In this study, G5, which is a small oligomer, was used as a model compound for PEO matrices. The thermal properties, ionic conductivity, and electrochemical stability of the electrolytes with ImZ2 were evaluated. The thermal stabilities of all the G5-based electrolytes with ImZ2 were above 150 °C, and the ionic conductivity values were in the range of 0.8–3.0 mS cm−1 at room temperature. When the electrolytes contained less than 5.5 wt% ImZ2, the ionic conductivity values were almost the same as that of the electrolyte without ImZ2. The electrochemical properties were improved with the incorporation of ImZ2. The anodic limit of the electrolyte with 5.5 wt% ImZ2 was 5.3 V vs. Li/Li+, which was over 1 V higher than that of G5/LiFSA.

Facile preparation and thermoelectric properties of Bi₂Te₃ based alloy nanosheet/PEDOT:PSS composite films

Bi2Te3 based alloy nanosheet (NS)/poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) composite films were prepared separately by spin coating and drop casting techniques. The drop cast composite film containing 4.10 wt % Bi2Te3 based alloy NSs showed electrical conductivity as high as 1295.21 S/cm, which is higher than that (753.8 S/cm) of a dimethyl sulfoxide doped PEDOT:PSS film prepared under the same condition and that (850-1250 S/cm) of the Bi2Te3 based alloy bulk material. The composite film also showed a very high power factor value, ∼32.26 μWm(-1) K(-2). With the content of Bi2Te3 based alloy NSs increasing from 0 to 4.10 wt %, the electrical conductivity and Seebeck coefficient of the composite films increase simultaneously.

The Glutathione System: a new drug target in neuroimmune disorders

Glutathione (GSH) has a crucial role in cellular signaling and antioxidant defenses either by reacting directly with reactive oxygen or nitrogen species or by acting as an essential cofactor for GSH S-transferases and glutathione peroxidases. GSH acting in concert with its dependent enzymes, known as the glutathione system, is responsible for the detoxification of reactive oxygen and nitrogen species (ROS/RNS) and electrophiles produced by xenobiotics. Adequate levels of GSH are essential for the optimal functioning of the immune system in general and T cell activation and differentiation in particular. GSH is a ubiquitous regulator of the cell cycle per se. GSH also has crucial functions in the brain as an antioxidant, neuromodulator, neurotransmitter, and enabler of neuron survival. Depletion of GSH leads to exacerbation of damage by oxidative and nitrosative stress; hypernitrosylation; increased levels of proinflammatory mediators and inflammatory potential; dysfunctions of intracellular signaling networks, e.g., p53, nuclear factor-κB, and Janus kinases; decreased cell proliferation and DNA synthesis; inactivation of complex I of the electron transport chain; activation of cytochrome c and the apoptotic machinery; blockade of the methionine cycle; and compromised epigenetic regulation of gene expression. As such, GSH depletion has marked consequences for the homeostatic control of the immune system, oxidative and nitrosative stress (O&NS) pathways, regulation of energy production, and mitochondrial survival as well. GSH depletion and concomitant increase in O&NS and mitochondrial dysfunctions play a role in the pathophysiology of diverse neuroimmune disorders, including depression, myalgic encephalomyelitis/chronic fatigue syndrome and Parkinson’s disease, suggesting that depleted GSH is an integral part of these diseases. Therapeutical interventions that aim to increase GSH concentrations in vivo include N-acetyl cysteine; Nrf-2 activation via hyperbaric oxygen therapy; dimethyl fumarate; phytochemicals, including curcumin, resveratrol, and cinnamon; and folate supplementation.

Colonizacao intracavitaria pulmonar por aspergillus niger : analise de suas peculiaridades

Trezentos pacientes portadores de colonização intracavitária pulmonar (pelos exames soro lógico e/ou tecidual) foram investigados num período de 10 anos. Os casos foram classificados como: Aspergillus fumigatus (246 casos); Ao niger (21 casos); A. flavus (7 casos); Pseudallescheria boydii (1 caso); colonização fúngica não especificada (21 casos) e colonização actinomicética (4 casos). os grupos A. niger (çasos)e A. fumigatus (controles) foram comparados a respeito de variáveis clínicas e laboratoriais, por serem os mais freqUentes e pela pobreza da literatura sobre A. niger. Esta análise mostrou associações estatisticamente significativas com o A. niger para;sexo masculino (Razão de Chances = 3,28; p <0,05); infecção nosocomial, ocorrendo em hospitais de conservação precária (RC = 150,8; p< 0,001); tuberculose ativa (RC = 8,03; P <0,001); diabete mélito tipo 11 (RC = 10,67; p

Prevalência de litíase renal e avaliação metabólica de pacientes com ressecção parcial do intestino delgado

Hiperoxalúria ocorre após ressecção extensa do intestino delgado na presença de um colon intacto. De 1984 a 1997, 40 pacientes com ressecção de intestino delgado, extensão maior do que 30cm, foram estudados com o objetivo de se avaliar a prevalência de litíase renal nesta população e alterações metabólicas associadas. Sete pacientes, correspondendo a 17,5% da população em estudo, desenvolveram um ou mais cálculos renais durante o período de observação correspondendo a uma incidência de 3,1 casos por 100 pessoas/ano. Os pacientes foram então divididos em dois grupos. Grupo 1 formado por 33 pacientes com ressecção intestinal que não formaram cálculos renais durante o período de observação e o Grupo 2 com 7 pacientes que formaram um ou mais cálculos renais após a ressecção intestinal. A excreção urinária de oxalato foi, em média, maior no grupo 2, que desenvolveram litíase renal, comparado com o grupo 1, não formadores de cálculos renais (49,2±23,8 mg/24horas Vs 30,6±3,4 mg/24h, p=0,004). De forma oposta, o magnésio foi menor nos pacientes formadores de cálculos renais comparado com os pacientes não formadores de cálculos (54,5±17,9 mg/24horas Vs 94,9±8,5 mg/24horas, p=0,028), assim como o citrato também foi menor nos pacientes com cálculo renal, mas sem diferença do ponto de vista estatístico (265,9±55,8 mEq/24horas Vs 404,8±49,7mEq/24horas, P= 0,278). Este estudo mostra que novos cálculos urinários podem ser detectados em um número significativo de pacientes que se submetem à cirurgia de ressecção do intestino delgado, provavelmente associado ao aumento da excreção de oxalato e diminuição de, pelo menos, um dos inibidores da cristalização de oxalato de cálcio, o magnésio. Por isto, se torna importante a monitorização destes pacientes, regularmente, mesmo após vários anos da cirurgia. É importante a monitorização pelo menos do oxalato e magnésio, na urina de 24 horas, já que ambos estão associados a um maior risco de desenvolvimento de cálculos renais.

Novel catalyst systems based on Ni(II), Ti(IV), and Cr(III) complexes for oligo-and polymerization of ethylene

The complex of Brookhart Ni(α-diimine)Cl2 (1) (α-diimine = 1,4-bis(2,6- diisopropylphenyl)-acenaphthenediimine) has been characterized after impregnation on silica (S1) and MAO-modified silicas (4.0, 8.0 and 23.0 wts.% Al/SiO2 called S2, S3 and S4, respectively). The treatment of these heterogeneous systems with MAO produces some active catalysts for the polymerization of the ethylene. A high catalytic activity has been gotten while using the system supported 1/S3 (196 kg of PE/mol[Ni].h.atm; toluene, Al/Ni = 1000, 30ºC, 60 min and atmospheric pressure of ethylene). The effects of polymerization conditions have been tested with the catalyst supported in S2 and the best catalytic activity has been gotten with solvent hexane, MAO as cocatalyst, molar ratio Al/Ni of 1000 and to the temperature of 30°C (285 kg of PE/mol[Ni].h.atm). When the reaction has been driven according to the in situ methodology, the activity practically doubled and polymers showed some similar properties. Polymers products by the supported catalysts showed the absence of melting fusion, results similar to those gotten with the homogeneous systems by DSC analysis. But then, polymers gotten with the transplanted system present according to the GPC’s curves the polydispersity (MwD) varies between 1.7 and 7.0. A polyethylene blend (BPE/LPE) was prepared using the complex Ni(α-diimine)Cl2 (1) (α-diimine = 1,4-bis(2,6-diisopropylphenyl)-acenaphthenediimine) and {TpMs*}TiCl3 (2) (TpMs* = hydridobis(3-mesitylpyrazol-1-yl)(5-mesitylpyrazol-1-yl)) supported in situ on MAO-modified silica (4.0 wts. -% Al/SiO2, S2). Reactions of polymerization of ethylene have been executed in the toluene in two different temperatures (0 and 30°C), varying the molars fraction of nickel (xNi), and using MAO as external cocatalyst. To all temperatures, the activities show a linear variation tendency with xNi and indicate the absence of the effect synergic between the species of nickel and the titanium. The maximum of activity have been found at 0°C. The melting temperature for the blends of polyethylene produced at 0 °C decrease whereas xNi increases indicating a good compatibility between phases of the polyethylene gotten with the two catalysts. The melting temperature for the blends of polyethylene showed be depend on the order according to which catalysts have been supported on the MAO-modified silica. The initial immobilization of 1 on the support (2/1/S2) product of polymers with a melting temperature (Tm) lower to the one of the polymer gotten when the titanium has been supported inicially (1/2/S2). The observation of polyethylenes gotten with the two systems (2/1/S2 and 1/2/S2) by scanning electron microscopy (SEM) showed the spherical polymer formation showing that the spherical morphology of the support to been reproduced. Are described the synthesis, the characterization and the catalytic properties for the oligomerization of the ethylene of four organometallics compounds of CrIII with ligands ([bis[2-(3,5-dimethyl-1-pyrazolyl)ethyl]amine] chromium (III) chloride (3a), [bis[2-(3,5- dimethyl-l-pyrazolyl)ethyl]benzylamine] chromium (III) chloride (3b), [bis[2-(3,5-dimethyl-lpyrazolyl) ethyl]ether] chromiun(III)chloride (3c), [bis[2-(3-phenyl-lpyrazolyl) ethyl]ether]chromiun(III)chloride (3d)). In relation of the oligomerization, at exception made of the compounds 3a, all complex of the chromium showed be active after activation with MAO and the TOF gotten have one effect differentiated to those formed with CrCl3(thf)3. The coordination of a tridentate ligand on the metallic center doesn't provoke any considerable changes on the formation of the C4 and C6, but the amount of C8 are decrease and the C10 and C12+ have increased. The Polymers produced by the catalyst 3a to 3 and 20 bar of ethylene have, according to analyses by DSC, the temperatures of fusion of 133,8 and 136ºC respectively. It indicates that in the two cases the production of high density polyethylene. The molar mass, gotten by GPC, is 46647 g/mols with MwD = 2,4 (3 bar). The system 3c/MAO showed values of TOF, activity and selectivity to different α-olefins according to the pressure of ethylene uses. Himself that shown a big sensibility to the concentration of ethylene solubilized.

Desenvolvimento e validação de método analítico para quantificação da boldina em peumus boldus mol. (monimiaceae) e avaliação preliminar de sua estabilidade

Peumus boldus Molina (Monimiaceae) é uma árvore comum e abundante no Chile, e suas folhas são amplamente empregadas pela medicina tradicional para o tratamento de uma variedade de afecções do sistema digestivo e hepatobiliar. Seus principais constituintes químicos são alcalóides do tipo aporfínicos, sendo a boldina seu maior e mais característico representante, cujas propriedades antioxidantes são extensivamente relatadas na literatura, servindo desta forma como marcador químico para a espécie. Com o objetivo de contribuir com parâmetros de controle de qualidade, um estudo botânico macro e microscópico das folhas e do pó da espécie foi realizado. Características morfológicas, identificadas pela análise macroscópica, como pilosidade, tipologia dos tricomas, proeminência ao redor da base dos tricomas e aparência do bordo, e características microscópicas como estômatos anomocíticos, folha hipoestomática e ocorrência de cristais de oxalato de cálcio denotam valor taxonômico. Parâmetros farmacopéicos como cinzas totais e perda por dessecação foram determinados, e um método de quantificação da boldina foi desenvolvido e validado utilizando a CLAE. O limite mínimo de boldina observado na análise de 10 amostras adquiridas foi de aproximadamente 0,016%. A fim de avaliarse o comportamento de seus constituintes químicos frente a variações de temperatura e umidade, realizou-se estudo de estabilidade acelerada (40ºC ± 2ºC / 75% ± 5% U.R.). A degradação máxima de boldina foi observada após 90 dias em câmara climática chegando a aproximadamente 52%. A reação de degradação sugerida foi de segunda ordem, e o tempo de vida útil e meia-vida calculados foram de aproximadamente 18 dias e 165 dias, respectivamente. Por fim, realizou-se a quantificação de alguns metais pesados nas folhas da espécie, que decresceram na ordem de Fe> Mn> Cu> Ni, sendo que Pb, Cr e Co tiveram níveis abaixo do limite de detecção de 5 μg/g.

Changes in volatile composition of Madeira wines during their oxidative ageing

The influence of the age in the volatile composition of Madeira wines made with Boal, Malvazia, Sercial and Verdelho varieties and aged in oak barrel during 1, 11 and 25 years old was been studied. For this purpose, the evolution of volatile compounds: higher alcohols, ethyl esters, fatty acids, furan compounds, enolic compounds, γ-lactones, dioxanes and dioxolanes, of the four most utilised varieties were determined using liquid–liquid extraction with dichloromeihane. Octan-3-ol was used as internal standard. The wines made with these varieties showed great differences in sugar content and small variations on pH and alcoholic degree. The results show that during ageing, the concentration of fatty acids ethyl esters, acetates and fatty acids decrease significantly contrarily to the great increase of ethyl esters of diprotic acids. There is a strong correlation between sotolon, 2-furfural, 5-methyl-2-furfural, 5-hydroxymethyl-2-furfural and 5-ethoxymethyl-2-furfural with wine ageing. These findings indicate that these compounds can be used as ageing wine markers. Among the molecules studied, sotolon [3-hydroxy-4,5-dimethyl-2(5H)-furanone] was one of the few molecules present in concentrations above the perception threshold in Madeira wines. 5-Eihoxymethyl-2-furfural formed from 5-hydroxymethyl-2-furfural and 2-furfural, derived from sugars, are also involved in the aroma of sweet fortified white wines aged in oxidative conditions. The sensory properties change significantly after long periods of conservation.