Effects of chemical composition on the corrosion of dental alloys

The aim of this study was to determine the effect of the oral environment on the corrosion of dental alloys with different compositions, using electrochemical methods. The corrosion rates were obtained from the current-potential curves and electrochemical impedance spectroscopy (EIS). The effect of artificial saliva on the corrosion of dental alloys was dependent on alloy composition. Dissolution of the ions occurred in all tested dental alloys and the results were strongly dependent on the general alloy composition. Regarding the alloys containing nickel, the Ni-Cr and Ni-Cr-Ti alloys released 0.62 mg/L of Ni on average, while the Co-Cr dental alloy released ions between 0.01 and 0.03 mg/L of Co and Cr, respectively.The open-circuit potential stabilized at a higher level with lower deviation (standard deviation: Ni-Cr-6Ti = 32 mV/SCE and Co-Cr = 54 mV/SCE). The potenciodynamic curves of the dental alloys showed that the Ni-based dental alloy with >70 wt% of Ni had a similar curve and the Co-Cr dental alloy showed a low current density and hence a high resistance to corrosion compared with the Ni-based dental alloys. Some changes in microstructure were observed and this fact influenced the corrosion behavior for the alloys. The lower corrosion resistance also led to greater release of nickel ions to the medium. The quantity of Co ions released from the Co-Cr-Mo alloy was relatively small in the solutions. In addition, the quantity of Cr ions released into the artificial saliva from the Co-Cr alloy was lower than Cr release from the Ni-based dental alloys.

Correlation between maxillary central incisor crown morphology and mandibular dental arch form in normal occlusion subjects

The aim of this study was to evaluate the correlation between the morphology of the mandibular dental arch and the maxillary central incisor crown. Cast models from 51 Caucasian individuals, older than 15 years, with optimal occlusion, no previous orthodontic treatment, featuring 4 of the 6 keys to normal occlusion by Andrews (the first being mandatory) were observed. The models were digitalized using a 3D scanner, and images of the maxillary central incisor and mandibular dental arch were obtained. These were printed and placed in an album below pre-set models of arches and dental crowns, and distributed to 12 dental surgeons, who were asked to choose which shape was most in accordance with the models and crown presented. The Kappa test was performed to evaluate the concordance among evaluators while the chi-square test was used to verify the association between the dental arch and central incisor morphology, at a 5% significance level. The Kappa test showed moderate agreement among evaluators for both variables of this study, and the chi-square test showed no significant association between tooth shape and mandibular dental arch morphology. It may be concluded that the use of arch morphology as a diagnostic method to determine the shape of the maxillary central incisor is not appropriate. Further research is necessary to assess tooth shape using a stricter scientific basis.

Effect of beverages on bovine dental enamel subjected to erosive challenge with hydrochloric acid

This study evaluated by an in vitro model the effect of beverages on dental enamel previously subjected to erosive challenge with hydrochloric acid. The factor under study was the type of beverage, in five levels: Sprite® Zero Low-calorie Soda Lime (positive control), Parmalat® ultra high temperature (UHT) milk, Ades® Original soymilk, Leão® Ice Tea Zero ready-to-drink low-calorie peach-flavored black teaand Prata® natural mineral water (negative control). Seventy-five bovine enamel specimens were distributed among the five types of beverages (n=15), according to a randomized complete block design. For the formation of erosive wear lesions, the specimens were immersed in 10 mL aqueous solution of hydrochloric acid 0.01 M for 2 min. Subsequently, the specimens were immersed in 20 mL of the beverages for 1 min, twice daily for 2 days at room temperature. In between, the specimens were kept in 20 mL of artificial saliva at 37ºC. The response variable was the quantitative enamel microhardness. ANOVA and Tukey's test showed highly significant differences (p<0.00001) in the enamel exposed to hydrochloric acid and beverages. The soft drink caused a significantly higher decrease in microhardness compared with the other beverages. The black tea caused a significantly higher reduction in microhardness than the mineral water, UHT milk and soymilk, but lower than the soft drink. Among the analyzed beverages, the soft drink and the black tea caused the most deleterious effects on dental enamel microhardness.

Connecting accuracy of interchanged prosthetic abutments to different dental implants using scanning electron microscopy

The present study evaluated the interchangeability of prosthetic components for external hexagon implants by measuring the precision of the implant/abutment (I/A) interface with scanning electron microscopy. Ten implants for each of three brands (SIN, Conexão, Neodent) were tested with their respective abutments (milled CoCr collar rotational and non-rotational) and another of an alternative manufacturer (Microplant) in randomly arranged I/A combinations. The degree of interchangeability between the various brands of components was defined using the original abutment interface gap with its respective implant as the benchmark dimension. Accordingly, when the result for a given component placed on an implant was equal to or smaller then that gap measured when the original component of the same brand as the implant was positioned, interchangeability was considered valid. Data were compared with the Kruskal-Wallis test at 5% significance level. Some degree of misfit was observed in all specimens. Generally, the non-rotational component was more accurate than its rotational counterpart. The latter samples ranged from 0.6-16.9 µm, with a 4.6 µm median; and the former from 0.3-12.9 µm, with a 3.4 µm median. Specimens with the abutment and fixture from Conexão had larger microgap than the original set for SIN and Neodent (p<0.05). Even though the latter systems had similar results with their respective components, their interchanged abutments did not reproduce the original accuracy. The results suggest that the alternative brand abutment would have compatibility with all systems while the other brands were not completely interchangeable.

Dental pulp vascular permeability changes induced by dental bleaching

Aiming to compare the effect of different light sources for dental bleaching on vascular permeability of dental pulps, forty-eight incisors were used. The bleaching agent (35 % hydrogen peroxide) was activated by halogen light; LED (Light Emitting Diode) or LED, followed by laser phototherapy (LPT) (λ = 780 nm; 3 J/cm²). After the bleaching procedures, the animals received an intra-arterial dye injection and one hour later were sacrificed. The teeth were diaphanized and photographed. The amount of blue stain content of each dental pulp was quantified using a computer imaging program. The data was statistically compared (p < 0.05). The results showed a significant higher (p < 0.01) dye content in the groups bleached with halogen light, compared with the control, LED and LED plus LPT groups. Thus, tooth bleaching activated by LED or LED plus LPT induces lesser resulted in increased vascular permeability than halogen light.

Dental caries-related quality of life and socioeconomic status of preschool children, Bauru, SP

AIM: To evaluate oral health-related quality of life of preschool children of Bauru, State of São Paulo, Brazil, and associate it with socioeconomic profile of households. METHODS: The sample consisted of 229 preschool children between 3 and 5 years and the dmft (decayed, missing due to caries, filled teeth) index was adopted for assessment children's dental caries in accordance with the standards recommended by the World Health Organization. Questionnaires were used for evaluation oral health-related quality of life (Early Childhood Oral Health Impact Scale) and socioeconomic profile of parents or guardians of the preschool children. Statistical analysis was performed descriptively by relative and absolute frequencies and by Spearman's correlation and Kruskal-Wallis test (p <0.05). RESULTS: A dmft of 1.65 (± 2.87) and a Sic Index 4.88 (± 3.20) were found, indicating the polarization of dental caries in the studied group. It was verified low influence of oral health on quality of life of the children examined. With respect to socioeconomic classification, 66.38% of families were in the lower middle class. Linear and statistically significant correlation was found between dmft and oral health-related quality of life for the overall score and domains of the questionnaire (p<0.001). CONCLUSIONS: It was found low influence of oral health on quality of life of the preschool children and the assessment of socioeconomic conditions of the children's families may guide practices aiming to reducing inequalities in the distribution of dental caries in the population.

Saliva and dental erosion

Dental erosion is a multifactorial condition. The consideration of chemical, biological and behavioral factors is fundamental for its prevention and therapy. Among the biological factors, saliva is one of the most important parameters in the protection against erosive wear. Objective: This review discusses the role of salivary factors on the development of dental erosion. Material and Methods: A search was undertaken on MeDLINe website for papers from 1969 to 2010. The keywords used in the research were "saliva", "acquired pellicle", "salivary flow", "salivary buffering capacity" and "dental erosion". Inclusion of studies, data extraction and quality assessment were undertaken independently and in duplicate by two members of the review team. Disagreements were solved by discussion and consensus or by a third party. Results: Several characteristics and properties of saliva play an important role in dental erosion. Salivary clearance gradually eliminates the acids through swallowing and saliva presents buffering capacity causing neutralization and buffering of dietary acids. Salivary flow allows dilution of the acids. In addition, saliva is supersaturated with respect to tooth mineral, providing calcium, phosphate and fluoride necessary for remineralization after an erosive challenge. Furthermore, many proteins present in saliva and acquired pellicle play an important role in dental erosion. Conclusions: Saliva is the most important biological factor affecting the progression of dental erosion. Knowledge of its components and properties involved in this protective role can drive the development of preventive measures targeting to enhance its known beneficial effects.

Dental age as indicator of adolescence

AIM: The purpose of the present study was to analyze the relationship between root formation of the first premolars and skeletal maturation stages identified in hand-wrist radiographs. METHODS: A cross-sectional study was carried out involving the panoramic and hand-wrist radiographs obtained on the same date of 232 patients, 123 boys and 109 girls aged 4 years and 5 months to 17 years and 12 months. Root formation stages of the first premolars were related to the ossification stages of the sesamoid bone, epiphyseal stages of the phalanx of the thumb and epiphyseal stages of the radius. RESULTS: The studied variables demonstrated statistically significant correlations. CONCLUSION: Roots of the lower first premolars do not reach 2/3 of their complete length before adolescence.

Evaluation of the dental arch asymmetry in natural normal occlusion and Class II malocclusion individuals

OBJECTIVE: To verify the presence and degree of asymmetry of dental arches in Brazilian individuals with natural normal occlusion and Class II, Divisions 1 and 2 malocclusions. METHODS: The study evaluated the symmetry of the maxillary and mandibular dental arches of 180 pairs of dental casts, divided into: Group I = 60 pairs of natural normal occlusion individuals; Group II = 60 pairs of Class II, Division 1 malocclusion individuals; and Group III = 60 pairs of Class II, Division 2 malocclusion individuals. A device was used to measure dental midline deviation and the canine tip in the dental arches (in degrees). It was also verified the distance of the upper canines from the palatal suture, intercanine distance, and anteroposterior upper and lower first molar position. RESULTS: Dental arches of individuals from all groups presented asymmetry, regardless of the presence of malocclusion. Group I showed a lower asymmetry degree in relation to Groups II and III. The asymmetry in Groups II and III was similar. CONCLUSION: The dental arches of individuals with natural normal occlusion and with Class II, Division 1 and Division 2 malocclusions showed asymmetry. The asymmetry degree was higher in the mandibular dental arches than in the maxillary dental arches in all 3 evaluated groups.

Dental caries associated factors in 12 year-old schoolchildren from a municipality in the state of São Paulo, Brazil

Objective To analyze the possible association between dental caries, fluorosis and the need for treatment in 12 year-old schoolchildren and the socioeconomic conditions of parents/guardians in the city of Franca, in the state of São Paulo. Methods A random sample of schoolchildren aged 12 was obtained from the school records in Franca, using a systematic random technique. The epidemiological survey was carried out by a single calibrated examiner, on 258 public and private schoolchildren in order to obtain the prevalence of dental caries, the need for treatment and the severity of dental fluorosis. Parents/guardians were also interviewed to assess their socioeconomic conditions (education and per capita income). We used multiple correlation analysis to investigate associations between category variables. Results It was possible to identify two distinct groups, with associations between the variables: the first group, represented by schoolchildren with average prevalence of caries, need for treatment, low level of parental education and income; and a second group represented by schoolchildren with low prevalence of caries, no need for treatment, high parental education and income. The two dimensions explained approximately 35% of total inertia. The factors within each group are related. Conclusion High income and parental education are associated with the low prevalence of dental caries but there is no association with dental fluorosis.

Socioeconomic and psychosocial predictors of dental healthcare use among Brazilian preschool children

Abstract Background Disparities in utilization of oral healthcare services have been attributed to socioeconomic and individual behavioral factors. Parents’ socioeconomic status, demographics, schooling, and perceptions of oral health may influence their children’s use of dental services. This cross-sectional study assessed the relationships between socioeconomic and psychosocial factors and the utilization of dental health services by children aged 1–5 years. Methods Data were collected through clinical exams and a structured questionnaire administered during the National Day of Children’s Vaccination. A Poisson regression model was used to estimate prevalence ratios and 95% confidence intervals. Results Data were collected from a total of 478 children. Only 112 (23.68%) were found to have visited a dentist; 67.77% of those had seen the dentist for preventive care. Most (63.11%) used public rather than private services. The use of dental services varied according to parental socioeconomic status; children from low socioeconomic backgrounds and those whose parents rated their oral health as “poor” used dental services less frequently. The reason for visiting the dentist also varied with socioeconomic status, in that children of parents with poor socioeconomic status and who reported their child’s oral health as “fair/poor” were less likely to have visited the dentist for preventive care. Conclusion This study demonstrated that psychosocial and socioeconomic factors are important predictors of the utilization of dental care services.

Surface treatment of dental porcelain with CO2 laser: porosity analysis and AFM.

The effect of CO2 continuous laser irradiation on the surface properties of veneering porcelains has already been tested. The surface observed after laser irradiation is similar to that achieved by auto-glaze in terms of roughness and color parameters (Sgura R, et al. Dental Materials 2011;27(Suppl. 1):e72–73). The purpose of this study was to analyze the surface porosity of porcelain discs after CO2 laser treatment and compare it to auto-glaze treatment, in furnace. A morphological analysis of the porcelain surface was conducted using atomic force microscopy (AFM) and conventional optical microscopy (OM).

Compressive strength of dental composites photo-activated with different light tips

The aim of this study was to evaluate the compressive strength of microhybrid (FiltekTM Z250) and nanofilled (FiltekTM Supreme XT) composite resins photo-activated with two different light guide tips, fiber optic and polymer, coupled with one LED. The power density was 653 mW cm-2 when using the fiber optic light tip and 596 mW cm-2 with the polymer. After storage in distilled water at 37± 2 °C for seven days, the samples were subjected to mechanical testing of compressive strength in an EMIC universal mechanical testing machine with a load cell of 5 kN and speed of 0.5 mm min-1. The statistical analysis was performed using ANOVA with a confidence interval of 95% and Tamhane’s test. The results showed that the mean values of compressive strength were not influenced by the different light tips (p > 0.05). However, a statistical difference was observed (p < 0.001) between the microhybrid composite resin photo-activated with the fiber optic light tip and the nanofilled composite resin. Based on these results, it can be concluded that microhybrid composite resin photo-activated with the fiber optic light tip showed better results than nanofilled, regardless of the tip used, and the type of the light tip did not influence the compressive strength of either composite. Thus, the presented results suggest that both the fiber optic and polymer light guide tips provide adequate compressive strength to be used to make restorations. However, the fiber optic light tip associated with microhybrid composite resin may be an interesting option for restorations mainly in posterior teeth.