Friction of sliding surfaces carrying adsorbed lubricant layers

In concentrated contacts the behaviour of lubricants is much modified by the high local pressures: changes can arise both from molecular ordering within the very thin film lubricant layers present at the interface as well as from the deposition on the component surfaces of more solid-like polymeric boundary layers. These 'third bodies' separating the solid surfaces may have rheological or mechanical properties very different from those observed in the bulk. Classical elasto-hydrodynamic theory considers the entrapped lubricant to exhibit a piezo-viscous behaviour while the conventional picture of more solid boundary lubricant layers views their shear strength r as being linearly dependent on local pressure p, so that T = TO + ap where TO and a are constants. If TO is relatively small, then the coefficient of friction \i = T Ip ~ a and so Amonton's laws are recovered. However, the properties of adsorbed or deposited surface films, or indeed other third bodies such as debris layers, may be more complex than this. A preliminary study has looked quantitatively at the influence of the pressure dependence of the shear strength of any surface layer on the overall friction coefficient of a contact which is made up of an array of asperities whose height varies in a Gaussian manner. Individual contact points may be elastic or plastic. The analysis results in plots of coefficient of friction versus the service or load parameter PIH&NRa where P is the nominal pressure on the contact, HS the hardness of the deforming surface, N the asperity density, R the mean radius of curvature of the asperities, and a is the standard deviation of their height distribution. In principle, any variation oft withp can be incorporated into the model; however, in this initial study we have used data on colloidal suspensions from the group at the Ecole Centrale de Lyon as well as examining the effect of functional relationships of somewhat greater complexity than a simple linear form. Results of the analysis indicate that variations in fj. are possible as the load is varied which depend on the statistical spread of behaviour at individual asperity contacts. The value of this analysis is that it attempts to combine the behaviour of films on the molecular scale with the topography of real engineering surfaces and so give an indication of the effects at the full-size or macro-scale that can be achieved by chemical or molecular surface engineering.

Movement of deposited water on turbomachinery rotor blade surfaces

A theoretical approach for calculating the movement of liquid water following deposition onto a turbomachine rotor blade is described. Such a situation can occur during operation of an aero-engine in rain. The equation of motion of the deposited water is developed on an arbitrarily oriented plane triangular surface facet. By dividing the blade surface into a large number of facets and calculating the water trajectory over each one crossed in turn, the overall trajectory can be constructed. Apart from the centrifugal and Coriolis inertia effects, the forces acting on the water arise from the blade surface friction, and the aerodynamic shear and pressure gradient. Non- dimensionalisation of the equations of motion provides considerable insight and a detailed study of water flow on a flat rotating plate set at different stagger angles demonstrates the paramount importance of blade surface friction. The extreme cases of low and high blade friction are examined and it is concluded that the latter (which allows considerable mathematical generalisation) is the most likely in practice. It is also shown that the aerodynamic shear force, but not the pressure force, may influence the water motion. Calculations of water movement on a low-speed compressor blade and the fan blade of a high bypass ratio aero-engine suggest that in low rotational speed situations most of the deposited water is centrifuged rapidly to the blade tip region. Copyright © 2006 by ASME.

Poroelastic indentation analysis for hydrated biological tissues

Indentation techniques are employed for the measurement of mechanical properties of a wide range of materials. In particular, techniques focused at small length-scales, such as nanoindentation and AFM indentation, allow for local characterization of material properties in heterogeneous materials including natural tissues and biomimetic materials. Typical elastic analysis for spherical indentation is applicable in the absence of time-dependent deformation, but is inappropriate for materials with time-dependent responses. Recent analyses for the viscoelastic indentation problem, based on elastic-viscoelastic correspondence, have begun to address the issue of time-dependent deformation during an indentation test. The viscoelastic analysis has been shown to fit experimental indentation data well, and has been demonstrated as useful for characterization of viscoelasticity in polymeric materials and in hydrated mineralized tissues. However, a viscoelastic analysis is not necessarily sufficient for multi-phase materials with fluid flow. In the current work, a poroelastic analysis-based on fluid motion through a porous elastic network-is used to examine spherical indentation creep responses of hydrated biological materials. Both analytical and finite element approaches are considered for the poroelastic Hertzian indentation problem. Modeling results are compared with experimental data from nanoindentation of hydrated bone immersed in water and polar solvents (ethanol, methanol, acetone). Baseline (water-immersed) bone responses are characterized using the poroelastic model and numerical results are compared with altered hydration states due to polar solvents. © 2007 Materials Research Society.

Ink-jet printing for patterning engineering surfaces

This work explored the use of industrial drop-on-demand inkjet printing for masking steel surfaces on engineering components, followed by chemical etching, to produce patterned surfaces. A solvent-based ink was printed on to mild steel samples and the influences of substrate topography and substrate temperature were investigated. Contact angle measurements were used to assess wettability. Regular patterns of circular spots (∼60 /on diameter) and more complex mask patterns were printed. Variation of the substrate temperature had negligible effect on the final size of the printed drops or on the resolution achieved. Colored optical interference fringes were observed on the dried ink deposits and correlated with film thickness measurements by whitelight interferometry.

Biological activities of skin secretions of the salamander Tylototriton verrucosus

Water-soluble skin secretions of salamander Tylototriton venucosus, first described by Anderson in 1871, were studied for their biological and enzymatic activities. They were found to be toxic to mice with an intraperitoneal LD50 of 11.5 mg/kg. Using Sephadex G-75 gel filtration, it was proven that the toxic components of the secretions are proteins with molecular weights ranging from 30,000 to 50,000 Da. The secretions of T. venucosus display a wide spectrum of antimicrobial activities and also contain both proteolytic activity and trypsin inhibitory activity. In contrast, neither hemolytic nor hemorrhagic activities were found. The secretions were determined to have phospholipase A(2) activity; however, no acetylcholine esterase activity was detectable under the assay conditions.

A preliminary study for establishing Perna viridis (Mollusca:Bivalvia) as a biological monitor for pollution in Karachi coastal water

Adverse effects of toxic substances on the environmental quality have become a subject of concern in recent years. Toxicity of heavy metals has never been in dispute and therefore their presence in our natural environment is undesirable. This study was undertaken to establish the capability of Perna viridis as a monitor for pollution in the Manora channel. Accumulation of Zinc, Copper, Iron and Manganese by marine mussels, sampled from Manora channel, was determined. Metal load varied markedly between individuals from the same populatin. This variability was partly accounted for systematic relationship between metal load and body weight and age. The distribution of metal between the major organs was considered, but the analysis of separate organs showed no advantage for their use as a biological monitor. comparison between Iron, Manganese, Copper and Zinc concentration in ambient sea water and in the mussel showed no clear correspondence. The results suggest that the mussel is capable of acting as a biological monitor, although may not be a good short term monitor of Iron, Manganese, Zinc and Copper. It may have potential as a long term and site comparison monitor for metals, once inherent variability is taken into account

Characterisation and simulation of asphalt road surfaces

Accurate simulation of rolling-tyre vibrations, and the associated noise, requires knowledge of road-surface topology. Full scans of the surface types in common use are, however, not widely available, and are likely to remain so. Ways of producing simulated surfaces from incomplete starting information are thus needed. In this paper, a simulation methodology based solely on line measurements is developed, and validated against a full two-dimensional height map of a real asphalt surface. First the tribological characteristics-asperity height, curvature and nearest-neighbour distributions-of the real surface are analysed. It is then shown that a standard simulation technique, which matches the (isotropic) spectrum and the probability distribution of the height measurements, is unable to reproduce these characteristics satisfactorily. A modification, whereby the inherent granularity of the surface is enforced at the initialisation stage, is introduced, and found to produce simulations whose tribological characteristics are in excellent agreement with the measurements. This method will thus make high-fidelity tyre-vibration calculations feasible for researchers with access to line-scan data only. In addition, the approach to surface tribological characterisation set out here provides a template for efficient cataloguing of road textures, as long as the resulting information can subsequently be used to produce sample realisations. A third simulation algorithm, which successfully addresses this requirement, is therefore also presented. © 2011 Elsevier B.V.

Biochemical and biological properties of Trimeresurus jerdonii venom and characterization of a platelet aggregation-inhibiting acidic phospholipase A(2)

Several biochemical and biological activities such as phospholipase A(2), arginine esterase, proteolytic, L-amino acid oxidase, 5'nucleotidase, acetylcholinesterase, thrombin-like, anticoagulant, and hemorrhagic activities were determined for whole desiccated venom of Trimeresurus jerdonii. An acidic phospholipase (named TJ-PLA(2)) was purified by anionic exchange chromatography, gel filtration, and reverse phase HPLC. TJ-PLA(2) had a molecular weight of 16,000 and a pI of 4.8. TJ-PLA(2) was non-lethal to mice up to an i.p. dose of 15 mg/kg body weight and lacked neurotoxicity and myotoxicity. It induced edema in the footpads of mice. The purified enzyme inhibited ADP- and collagen-induced human platelet aggregation in a manner which was both dose- and time-dependent.

Purification, cloning and biological characterization of a novel disintegrin from Trimeresurus jerdonii venom

A novel disintegrin, jerdonin, was purified from the Trimeresurus jerdonii venom by means of gel filtration and reverse phase high pressure liquid chromatography. Its coding cDNA was also isolated from the venom gland. The jerdonin coding cDNA is part of

Purification, characterization and biological activity of an L-amino acid oxidase from Trimeresurus mucrosquamatus venom

An L-amino acid oxidase (TM-LAO) from the venom of Hunan Trimeresurus mucrosquamatus was purified to homogenicity by three steps including DEAE Sephadex A-50 ion-exchange chromatography, Sephadex G-75 gel filtration and Resourse Q ion-exchange chromatography. TM-LAO is composed of two identical subunits with a molecular weight of 55 kD by SDS-polyacrylamide gel electrophoresis. The molecular weight was different with that of LAO purified from the same species distributed in Taiwan that was 70 kD. The 24 N-terminal ammo acid sequence of TM-LAO is ADNKNPLEECFRETNYEEFLEIAR, which shares high similarity with other Viperid snake venom LAOs and has moderate similarity with Elapid snake venom LAOs. Further studies found that TM-LAO inhibited the growth of E. colt, S. aurues and B. dysenteriae. TM-LAO also showed cytotoxicity and platelet aggregation activity. All the biological activities were eliminated by catalase, a H2O2 scavenger. It shows that these biological effects are possibly due to the formation of H2O2 produced by TM-LAO.

Designing of a single pack wash primer for aluminium surfaces in a marine environment

Design aspects and comparative performances of different laboratory formulations of wash primers were studied under laboratory and field conditions with reference to scratch hardness, flexibility, stability, resistance to corrosion and adhesiveness. The different formulations of single pack wash primers tested have shown superiority of the formulation prepared out of “mowital” and that it is comparable in performance to double pack wash primer.

Problems associated with the over protection of fishing trawlers against sea water corrosion and fouling

Some presently used anti-fouling materials contain metals and other compounds, which are toxic in the environment. Coating products are not always stable, and there is a resulting pollution hazard. In particular if surfaces are poorly prepared and manufactures' instructions are not closely followed the application of anti-fouling substances becomes pointless and dangerous. In addition the salinity, constant biological activity and suspended particles make seawater a highly corrosive material in its own right.

Preliminary biological evaluation of some formulated feeds for P. monodon

Rice bran is widely used by fish farmers as supplementary feed while soybean cake is used both as feed and as fertilizer in fishponds. Both fish meal and shrimp head have been found acceptable as feed ingredients. However, not much is known of the acceptability and efficiency of a mixture of these ingredients as feed for Penaeus monodon larvae. Ninety 127-day old P. monodon were measured for length and weight and were randomly divided into nine aquaria each containing 20 liters of water. These were fed 'lampirong' for two months previous to the study. There were three replications for each treatment. Length, weight, and survival rates were used to compare the efficiency of the diets. Weighed amounts of pellets equivalent to 100% of the body weight were fed during the first three days and reduced to 50% thereafter. A stopwatch was used to determine the length of time that elapsed before the shrimps would approach the pellet. Ten shrimps approximately 4 months in age were placed in 10 liters of water in a 25-liter aquarium. Two grams of each pellet type were placed simultaneously on opposite sides of the aquarium. The time that elapsed from the moment the pellets sunk to the bottom up to the time that any one shrimp approached the pellets was recorded. The group fed the imported pellets gained the most. Those fed FP-2s-77 elongated faster than those fed FP-1s-77. Survival rate of those fed FP-2s-77 was 37% while those fed imported pellets was 73%. Both 1s and 2s pellets disintegrated in water easily but the imported pellets were stable even after six hours in water. The attractability test for the pellets showed that the prawns were more readily attracted to the pellets 1s and 2s than to the imported pellets.

Comparative efficiency of different surfaces for drying fish

The efficiency of four different drying surfaces, namely, cement platform, palmyrah leaf mat, aluminum tray and stretched net for drying fish were studied using sciaenids, mullet and perch. All the drying surfaces were found to be equally efficient. The cheaper and locally available palmyrah leaf mat or stretched net can replace costly cement platform and aluminium tray for efficient drying of fish.