Study of a gold electrode modified by trans-[Ru(NH(3))(4)(Ist)SO(4)](+) to produce an electrochemical sensor for nitric oxide

The modification of a gold electrode surface by electropolymerization of trans-[Ru(NH(3))(4)(Ist)SO(4)](+) to produce an electrochemical sensor for nitric oxide was investigated. The influence of dopamine, serotonin and nitrite as interferents for NO detection was also examined using square-wave voltammetry (SWV). The characterization of the modified electrode was carried out by cyclic voltammetry, electrochemical quartz crystal microbalance (EQCM) and SERS techniques. The gold electrode was successfully modified by the trans-[Ru(NH(3))(4)(Ist)SO(4)](+) complex ion using cyclic voltammetry. The experiments show that a monolayer of the film is achieved after ten voltammetric cycles, that NO in solution can coordinate to the metal present in the layer, that dopamine, serotonin and nitrite are interferents for the detection of NO, and that the response for the nitrite is much less significant than the responses for dopamine and serotonin. The proposed modified electrode has the potential to be applied as a sensor for NO. (C) 2011 Elsevier Ltd. All rights reserved.

Development and Application of a Highly Selective Biomimetic Sensor for Detection of Captopril, an Important Ally in Hypertension Control

A biomimetic sensor is proposed as a promising new analytical method for determination of captopril in different classes of samples. The sensor was prepared by modifying a carbon paste electrode with iron (II) phthalocyanine bis(pyridine) [FePe(dipy)] complex. Amperometric measurements in a batch analytical mode were first carried out in order to optimize the sensor response. An applied potential lower than 0.2 V vs Ag vertical bar AgCl in 0.1 mol L(-1) of TRIS buffer at pH 8.0 provided the best response, with a linear range of 2.5 x 10(-5) to 1.7 x 10(-4) mol L(-1). A detailed investigation of the selectivity of the sensor, employing seventeen other drugs, was also performed. Recovery studies were carried out using biological and environment samples in order to evaluate the sensor`s potential for use with these sample classes. Finally, the performance of the biomimetic sensor was optimized in a flow injection (FIA) system using a wall jet electrochemical cell. Under optimized flow conditions, a broad linear response range, from 5.0 x 10(-4) to 2.5 x 10(-2) mol L(-1), was obtained for captopril, with a sensitivity of 210 +/- 1 mu A L mol(-1).

Novel Application of 2D and 3D-Similarity Searches To Identify Substrates among Cytochrome P450 2C9, 2D6, and 3A4

Cytochrome P450 (CYP450) is a class of enzymes where the substrate identification is particularly important to know. It would help medicinal chemists to design drugs with lower side effects due to drug-drug interactions and to extensive genetic polymorphism. Herein, we discuss the application of the 2D and 3D-similarity searches in identifying reference Structures with higher capacity to retrieve Substrates of three important CYP enzymes (CYP2C9, CYP2D6, and CYP3A4). On the basis of the complementarities of multiple reference structures selected by different similarity search methods, we proposed the fusion of their individual Tanimoto scores into a consensus Tanimoto score (T(consensus)). Using this new score, true positive rates of 63% (CYP2C9) and 81% (CYP2D6) were achieved with false positive rates of 4% for the CYP2C9-CYP2D6 data Set. Extended similarity searches were carried out oil a validation data set, and the results showed that by using the T(consensus) score, not only the area of a ROC graph increased, but also more substrates were recovered at the beginning of a ranked list.

3D roll-forming of hat-profile with variable depth and width

The use of roll-formed products in automotive, furniture, buildings etc. increases every year due to the low part-production cost and the complicated cross-sections that can be produced. The limitation with roll-forming until recent years is that one could only produce profiles with a constant cross-section in the longitudinal direction. About eight years ago ORTIC AB [1] developed a machine in which it was possible to produce profiles with a variable width (“3D roll-forming”) for the building industry. Experimental equipment was recently built for research and prototyping of profiles with variable cross-section in both width and depth for the automotive industry. The objective with the current study is to investigate the new tooling concept that makes it possible to roll-form hat-profiles, made of ultra high strength steel, with variable cross-section in depth and width. The result shows that it is possible to produce 3D roll-formed profiles with close tolerances.

Ökad insikt i den 3D-grafiska arbetsprocessen : Visualisering av interiörmiljöer i stillbilder

Föreliggande studie har haft för avsikt att genom enkäter undersöka likheter och skillnader mellan branschaktiva 3D-grafikers arbetsprocesser. Målet har varit att öka insikten i den 3D-grafiska arbetsprocessen för visualisering av interiörmiljöer. Studien är tänkt att identifiera vilka arbetsmoment som är mest tidskrävande och varför. En ökad insikt i denna process kan leda till förbättrad kommunikation och förståelse mellan kund och byrå. Respondenternas beskrivningar av arbetsprocessen liknade varandra och stämmer till stor del även med beskrivningar i litteraturen. De flesta av respondenterna upplevde modellering som det mest tidskrävande tekniska momentet. God kommunikation med kunden ansåg respondenterna vara viktigt för att undvika onödig korrektur, vilket beskrevs som problematiskt och tidskrävande. Respondenterna hade erfarenhet från referensmaterial av varierande kvalitet, vilket kan påverka ett projekts tidsåtgång.

Metamorphic epiphany -- 3D animation

As far back as I can remember, I have always been interested in studio art. Whether it be painting, drawing, printmaking, or photography, it has consistently been a part of my life. Upon enrolling in Colby, I became interested in computers and decided to major my undergraduate college career in Computer Science. Not forgetting past interests, I continued my studio art education, taking several classes within the Art department. In due time, I began combining interests and began studying Computer Graphics and Design. With limited resources in this field at Colby, the majority of my computer graphic education and experience has been done on my own time apart from regular classroom work. As time progressed, so did my interests. Starting with simple image manipulation of digitally scanned photographs, I moved on to Web Page design, eventually leading to Desktop Publishing. Ultimately, I wanted to take a step further and expand my overall computer graphic knowledge by learning 3D modeling and animation. With even fewer resources in 3D animation at Colby, I perceived having trouble finding the information and tools I would need to gain the necessary skills for this new field. The Senior Scholars program gave me the opponunity to find and acquire the necessary tools to pursue my interest. This program also allowed me to devote the proper amount of time required for learning these new tools.