The use of locally available materials in fish feed production

In Nigeria, the culture of fish is gaining importance, but local fish farmers face a set back because of the stoppage on importation of fish feed. Locally available raw materials such as yam, plantain, banana, cowpeas, macuna, maize, cassava, millet, sorghum, groundnut, sunnhemp seed and brewery wastes are considered as potential materials for fish feed. These have been examined on their minimum protein contributions since this is the most expensive part of the fish feed. Alternative sources to animal proteins are also examined. Plant protein from groundnut, melon, mucuna and others compare favourably with bloodmeal mixture and thus can be used to replace the more expensive animal proteins. Pellet feed can be produced on a small scale or commercial basis from the locally available raw materials and the fish farmer is advised to seek assistance from qualified fisheries personnel

The power of fish trader associations in the marketing of fish in Lagos State

This paper focusses on the activities of trade associations in the marketing of fish in Lagos State. The study covers 6 different markets in Lagos State of Nigeria. Analysis indicates that 86% of the traders are members of the associations. The ages of the traders range from 21 to over 55 years. However, majority are between the ages of 31 and 45 years. Traders secure their initial capital mostly from trade associations and Esusu/Ajo. Most traders have no working capital to maintain a regular series of outlets, so wholesalers turn to associations for funds, while retailers turn to wholesalers. They eventually pay back when they sell to consumers. The fish industry is found to be imperfectly competitive mostly because of the actions of fish trader associations. The fish marketing system is highly personalised and loyality exists between wholesalers and retailers and their customers

An assessment of the implementation of alternative income sources for fishermen's wives as a strategy for poverty alleviation under the Kainji Lake Fisheries Promotion Project

Kainji Lake Basin is the first man-made Lake in Nigeria with a surface area of 1270km super(2). Since its creation in 1968 research activities were carried out on biological, socio-economic, hydrological and limnological characteristics of the water body. Extension activities concentrated on the dissemination of proven technologies developed by the Research scientists. Most of the socio-economic and extension activities focused on fishermen as women were regarded as homemakers and their activities concentrated in the home. The situation is even compounded by the Islamic injunction of seclusion. The intervention of NGKLFPP in 1993 has introduced many changes into the research and extension activities directed at the beneficiaries of the project because women were considered as a major stakeholder around the Lake area. The intervention of the project in Kainji Lake in the introduction of alternative income generating activities to women is enumerated in this paper. The intervention has improved the living standard of women and to a certain level reduced poverty among women in the area

Limits and tradeoffs in the control of autocatalytic systems

Despite the complexity of biological networks, we find that certain common architectures govern network structures. These architectures impose fundamental constraints on system performance and create tradeoffs that the system must balance in the face of uncertainty in the environment. This means that while a system may be optimized for a specific function through evolution, the optimal achievable state must follow these constraints. One such constraining architecture is autocatalysis, as seen in many biological networks including glycolysis and ribosomal protein synthesis. Using a minimal model, we show that ATP autocatalysis in glycolysis imposes stability and performance constraints and that the experimentally well-studied glycolytic oscillations are in fact a consequence of a tradeoff between error minimization and stability. We also show that additional complexity in the network results in increased robustness. Ribosome synthesis is also autocatalytic where ribosomes must be used to make more ribosomal proteins. When ribosomes have higher protein content, the autocatalysis is increased. We show that this autocatalysis destabilizes the system, slows down response, and also constrains the system’s performance. On a larger scale, transcriptional regulation of whole organisms also follows architectural constraints and this can be seen in the differences between bacterial and yeast transcription networks. We show that the degree distributions of bacterial transcription network follow a power law distribution while the yeast network follows an exponential distribution. We then explored the evolutionary models that have previously been proposed and show that neither the preferential linking model nor the duplication-divergence model of network evolution generates the power-law, hierarchical structure found in bacteria. However, in real biological systems, the generation of new nodes occurs through both duplication and horizontal gene transfers, and we show that a biologically reasonable combination of the two mechanisms generates the desired network.

Implementation of a nursing competency assessment system in public hospitals

Numerous problems are frequently observed when nursing competency assessment systems (NCAS) are implemented. How to effectively implement a nursing competency assessment system, according to academic and practical contributions, is poorly reported in the literature. The purpose of this paper is to present a set of recommendations for public hospitals and nursing management in order to facilitate the implementation of a NCAS. To achieve this objective we have revised the existing literature and conducted a Delphi study with nursing managers and human resource managers of the public hospitals of the Basque Health Service. The results are that the implementation of a NCAS requires a well-planned strategy that managers must consider before implementing any NCAS. This strategy must include, at minimum, the following aspects: communication, training, leadership, and content where the NCAS is concerned. The context of the organisations and the cultural dimensions may also influence the results of the application of the system.

Optimization of optical parametric chirped pulse amplification with different pump wavelengths

Optical parametric chirped pulse amplification with different pump wavelengths was investigated using LBO crystal, at signal central wavelength of 800 nm. According to our theoretical simulation, when pump wavelength is 492.5 nm, there is a maximal gain bandwidth of 190 nm. centered at 805 nm in optimal noncollinear angle using LBO. Presently, pump wavelength of 492.5 nm can be obtained from second harmonic generation of a Yb:Sr-5(PO4)(3)F laser. The broad gain bandwidth can completely support similar to 6 fs with a spectral centre of seed pulse at 800 nm. The deviation from optimal noncollinear angle can be compensated by accurately tuning crystal angle for phase matching. The gain spectrum with pump wavelength of 492.5 nm is much better than those with pump wavelengths of 400, 526.5 and 532 nm, at signal centre of 800 nm. (c) 2005 Elsevier B.V. All rights reserved.

Developing and characterizing bulk metallic glasses for extreme applications

Metallic glasses have typically been treated as a “one size fits all” type of material. Every alloy is considered to have high strength, high hardness, large elastic limits, corrosion resistance, etc. However, similar to traditional crystalline materials, properties are strongly dependent upon the constituent elements, how it was processed, and the conditions under which it will be used. An important distinction which can be made is between metallic glasses and their composites. Charpy impact toughness measurements are performed to determine the effect processing and microstructure have on bulk metallic glass matrix composites (BMGMCs). Samples are suction cast, machined from commercial plates, and semi-solidly forged (SSF). The SSF specimens have been found to have the highest impact toughness due to the coarsening of the dendrites, which occurs during the semi-solid processing stages. Ductile to brittle transition (DTBT) temperatures are measured for a BMGMC. While at room temperature the BMGMC is highly toughened compared to a fully glassy alloy, it undergoes a DTBT by 250 K. At this point, its impact toughness mirrors that of the constituent glassy matrix. In the following chapter, BMGMCs are shown to have the capability of being capacitively welded to form single, monolithic structures. Shear measurements are performed across welded samples, and, at sufficient weld energies, are found to retain the strength of the parent alloy. Cross-sections are inspected via SEM and no visible crystallization of the matrix occurs.

Next, metallic glasses and BMGMCs are formed into sheets and eggbox structures are tested in hypervelocity impacts. Metallic glasses are ideal candidates for protection against micrometeorite orbital debris due to their high hardness and relatively low density. A flat single layer, flat BMG is compared to a BMGMC eggbox and the latter creates a more diffuse projectile cloud after penetration. A three tiered eggbox structure is also tested by firing a 3.17 mm aluminum sphere at 2.7 km/s at it. The projectile penetrates the first two layers, but is successfully contained by the third.

A large series of metallic glass alloys are created and their wear loss is measured in a pin on disk test. Wear is found to vary dramatically among different metallic glasses, with some considerably outperforming the current state-of-the-art crystalline material (most notably Cu₄₃Zr₄₃Al₇Be₇). Others, on the other hand, suffered extensive wear loss. Commercially available Vitreloy 1 lost nearly three times as much mass in wear as alloy prepared in a laboratory setting. No conclusive correlations can be found between any set of mechanical properties (hardness, density, elastic, bulk, or shear modulus, Poisson’s ratio, frictional force, and run in time) and wear loss. Heat treatments are performed on Vitreloy 1 and Cu₄₃Zr₄₃Al₇Be₇. Anneals near the glass transition temperature are found to increase hardness slightly, but decrease wear loss significantly. Crystallization of both alloys leads to dramatic increases in wear resistance. Finally, wear tests under vacuum are performed on the two alloys above. Vitreloy 1 experiences a dramatic decrease in wear loss, while Cu₄₃Zr₄₃Al₇Be₇ has a moderate increase. Meanwhile, gears are fabricated through three techniques: electrical discharge machining of 1 cm by 3 mm cylinders, semisolid forging, and copper mold suction casting. Initial testing finds the pin on disk test to be an accurate predictor of wear performance in gears.

The final chapter explores an exciting technique in the field of additive manufacturing. Laser engineered net shaping (LENS) is a method whereby small amounts of metallic powders are melted by a laser such that shapes and designs can be built layer by layer into a final part. The technique is extended to mixing different powders during melting, so that compositional gradients can be created across a manufactured part. Two compositional gradients are fabricated and characterized. Ti 6Al¬ 4V to pure vanadium was chosen for its combination of high strength and light weight on one end, and high melting point on the other. It was inspected by cross-sectional x-ray diffraction, and only the anticipated phases were present. 304L stainless steel to Invar 36 was created in both pillar and as a radial gradient. It combines strength and weldability along with a zero coefficient of thermal expansion material. Only the austenite phase is found to be present via x-ray diffraction. Coefficient of thermal expansion is measured for four compositions, and it is found to be tunable depending on composition.

Sozioökonomischer Vergleich der niedersächsischen und schleswig-holsteinischen Fischereiwirtschaft

In der "Ökosystemforschung niedersächsisches Wattenmeer" wird in einem Teilprojekt seit Januar 1993 "Die sozioökonomische Entwicklung der Fischerei im niedersächsischen Wattenmeer und ihr Bezug zu Naturschutzforderungen" untersucht. Im Rahmen dieses Projektes wurde am 19.05.1994 auf dem 4. Wissenschaftlichen Symposium der Ökosystemforschung Wattenmeer in Husum ein Vortrag gehalten, dessen Kurzfassung im folgenden wiedergegeben wird.

Patrón del comportamiento alimentario en escolares

[ES] En la edad escolar se adquieren los hábitos alimentarios que se seguirán, probablemente, durante gran parte de la vida. Objetivos: Conocer y valorar cualitativa y cuantitativamente la dieta semanal de un grupo de escolares y observar las diferencias de ingesta en los días escolares y los del fin de semana. El consumo en raciones de alimentos es más adecuado en los niños con normopeso y en los días escolares. Es precisa una educación nutricional de los niños y su entorno.

Hizkuntzaren sustrai biologikoen inguruan

[EUS] Hizkuntzaren sustrai biologikoen ikerketak aurrerapausu handiak egin ditu azken urteotan. Ikerketa hau alorrartekoa da nahitaez, eta hizkuntzalaritza, psikologia, neurozientzia eta genetikaren arteko bilbatura batek osatzen du «biohizkuntzalaritza» eta hizkuntzaren neurokognizioa itxuratzea xede duen eremu berri hau. Artikulu honetan ezagutza eremu honen hastapeneko itxurapen bat eskainzen da, hizkuntzaren genetikan eta neurokognizioan azken urteotan egin diren zenbait urrats aurkeztuaz.

Gamma-ray induced color centers in Yb : YAG crystals grown by Czochralski method

20 at.% Yb:YAG single crystals have been grown by the CZ method and gamma-ray irradiation induced color centers and valence change of Fe3+ and Yb3+ ions in Yb:YAG have been studied. One significant 255 nm absorption band was observed in as-grown crystals and was attributed to Fe3+ ions. Two additional absorption (AA) bands located at 255 nm and 345 nm, respectively, were produced after gamma irradiation. The changes in the AA spectra after gamma irradiation and air annealing are mainly related to the charge exchange of the Fe3+, Fe2+, oxygen vacancies and F-type color centers. Analysis shows that the broad AA band is associated with Fe2+ ions and F-type color centers. The transition Yb3+ Yb2+ takes place as an effect of recharging of one of the Yb3+ ions from a pair in the process of gamma irradiation. (C) 2006 Elsevier Ltd. All rights reserved.

Mechanisms of femtosecond laser-induced damage in magnesium fluoride

We studied the single-shot damage in magnesium fluoride irradiated by 800 nm femtosecond (fs) laser. The dependence of damage thresholds on the laser pulse durations from 60 to 750 fs was measured. The pump-probe measurements were carried out to investigate the time-resolved electronic excitation processes. A coupled dynamic model was applied to study the microprocesses in the interaction between fs laser and magnesium fluoride. The results indicate that both multiphoton ionization and avalanche ionization play important roles in the femtosecond laser-induced damage in MgF2. (C) 2006 Elsevier Ltd. All rights reserved.

Femtosecond laser-induced ZnSe nanowires on the surface of a ZnSe wafer in water

We present a simple route for ZnSe nanowire growth in the ablation crater on a ZnSe crystal surface. The crystal wafer, which was horizontally dipped in pure water, was irradiated by femtosecond laser pulses. No furnace, vacuum chamber or any metal catalyst were used in this experiment. The size of the nanowires is about 1-3 mu m long and 50-150 nm in diameter. The growth rate is 1-3 mu m/s, which is much higher than that achieved with molecular-beam epitaxy and chemical vapor deposition methods. Our discovery reveals a rapid and simple way to grow nanowires on designed micro-patterns, which may have potential applications in microscopic optoelectronics. (C) 2007 Elsevier Ltd. All rights reserved.

Ergebnisse weiterer Versuche mit Schersegeln

Als Schersegel werden hydrodynamische Auftriebsvorrichtungen am Kopftau von Schleppnetzen bezeichnet, die in ihrer Wirkungsweise einem Höhenscherbrett entsprechen. Im Gegensatz zu der starren Konstruktion eines Höhenscherbretts aus Holz oder Aluminium bestehen Schersegel jedoch aus flexiblem Material, im allgemeinen beidseitig kunststoffbeschichtetem Gewebe.

Changes in Fish Communities in the Upper Patuxent River from 1966 to 1977

Ten year comparison of fish survey's with respect to diversity evenness and composition of fish communities. The upper Patuxent River was divided into Piedmont Plateau and Coastal Plain regions, not only for geographical purposes, but also because of the clustering of sewage treatment plants in the Coastal Plain region. In the Piedmont Plateau region, the fish species diversity changed very little from 1966 to 1977 ( Little Patuxent -- 2.82 to 2.66; Middle Patuxent -- 2.86 to 2.83; and main stem -- 2.46 to 2.63), except in a section of Little Patuxent River at and below the City of Columbia where the species diversity index showed a significant reduction from 2.97 to 1.99, and in a section of the main stem Patuxent River immediately downstream from the Brighton Dam of the Triadelphia Reservoir where the index increased significantly from 1.66 to 3.20. In the Coastal Plain region, a significant reduction in the fish species diversity index occurred between 1966 and 1977 below the two sewage treatment plant outfalls : Savage -- 2.69 to 0 and Patuxent-Crofton -- 3.06 to 1.33. Also, the substantial reduction in the species diversity index which had already occurred in 1966 below the six other plant: outfalls of Fort Meade No. I, Fort Meade No. 2, Maryland House of Correction, Maryland City , Parkway and Bowie, remained depressed in 1977. On the other hand, below the Horsepen Sewage Treatment Plant (a tertiary plant practicing dechlorination) the species diversity index increased from 1.91 to 2.8. (PDF contains 48 pages)