Comparison of model predictions and speed trial results for a group of 32' wooden trawlers

Speed trial results of six 32' wooden stern, trawlers built to the same design are analyzed to determine the EHP ship Froude number curves in each case and are compared with the model test results of the same design and for the corresponding, displacement, conditions.

COMPARISON OF MILLISECOND ANNEALING OF B IMPLANTS AND ISOTHERMAL ANNEALING FOR TIMES OF A FEW SECONDS.

The annealing behaviour of B implants in the millisecond time regime using a combination of swept line beam and background heating is compared with isothermal annealing with heating cycles of a few seconds. Carrier concentration profiles show that under annealing conditions which restrict diffusion, millisecond processing gives higher activation of B implants than isothermal heating. Transmission electron microscopy shows that millisecond annealing also results in a lower defect density.

Comparison of growth and conversion efficiency of the freshwater prawn Macrobrachium malcolmsonii (H. Milne Edwards) juveniles fed with formulated and commercial feeds

A nutritional study was carried out to know the feasibility of formulated and commercial feeds on the growth of juveniles of the freshwater prawn Macrobrachium malcolmsonii. Best relative growth rate was observed for feed 1 followed by feeds 2 and 3. Animals fed with feed 1 showed higher production than the other feeds. Higher assimilation efficiency was noticed in the animals provided with feeds 5 and 4. Higher gross and net growth efficiencies were observed in the animals offered feed 1. Among the commercial feeds, feed 3 may considered to be suitable alternative to feed 1.

Experimental and theoretical comparison between static and dynamic torsional soil tests

The dynamic properties of dry Leighton Buzzard sand have been investigated using a resonant column test apparatus. These data are compared with very low frequency cyclic tests on identical specimens of sand. The comparison indicates that the properties of dry sand are independent of frequency. A simple one-dimensional model of kinematic hardening plasticity is used to predict the dynamic behaviour of the sand. The input parameters for this model are based on the results of static tests. These may be conducted on standard laboratory equipment with only minor modifications. The predictions are in good agreement with the measured data.

Comparison of different scheduling techniques for H-infinity controllers

Several approaches to designing schedule H-infinity control systems are compared. These include a controller switching approach and also parameter scheduling of an observer representation of the controller. They are illustrated by application to a Generic VSTOI. Aircraft Model (GVAM) supplied by The Royal Aerospace Establishment (RAE) at Bedford. The switched design has been tested on the simulator at RAE Bedford. The linear H-infinity designs make use of a loop-shaping followed by robust stabilisation to additive perturbations of a normalised coprime factorisation of the shaped plans. The different scheduling approaches are compared with respect to achieved robust stability levels. performance and complexity of implementation.

A Comparison of the bacterial flora of surface and sub-surface water of the sea off Ceylon

Under stable conditions of stratification of the sea, evidence of generic differences of the associated bacterial flora of the water masses has been obtained, between surface and sub-surface water. Gram negative rods, especially pseudomonads and achromobacters were more frequent at the surface. The fermentative and oxidase negative flora was more frequent in sub-surface water. The surface water in general had a greater variety of bacterial types while the sub-surface water had a flora with a greater range of biochemical activity. These results are discussed in relation to the hydrological condition of the water masses and the bacterial flora of freshly caught fish.

A comparison of different failure assessment methodologies applied to the NESC-1 test

Predictions for a 75x205mm surface semi-elliptic defect in the NESC-1 spinning cylinder test have been made using BS PD 6493:1991, the R6 procedure, non-linear cracked body finite element analysis techniques and the local approach to fracture. All the techniques agree in predicting ductile tearing near the inner surface of the cylinder followed by cleavage initiation. However they differ in the amount of ductile tearing, and the exact location and time of any cleavage event. The amount of ductile tearing decreases with increasing sophistication in the analysis, due to the drop in peak crack driving force and more explicit consideration of constraint effects. The local approach predicts a high probability of cleavage in both HAZ and base material after 190s, while the other predictions suggest that cleavage is unlikely in the HAZ due to constraint loss, but likely in the underlying base material. The timing of this event varies from ∼150s for R6 predictions to ∼250-300s using non-linear cracked body analysis.

A comparison of methods for assessing the lifetime reliability of a moored FPSO

Current design codes for floating offshore structures are based on measures of short-term reliability. That is, a design storm is selected via an extreme value analysis of the environmental conditions and the reliability of the vessel in that design storm is computed. Although this approach yields valuable information on the vessel motions, it does not produce a statistically rigorous assessment of the lifetime probability of failure. An alternative approach is to perform a long-term reliability analysis in which consideration is taken of all sea states potentially encountered by the vessel during the design life. Although permitted as a design approach in current design codes, the associated computational expense generally prevents its use in practice. A new efficient approach to long-term reliability analysis is presented here, the results of which are compared with a traditional short-term analysis for the surge motion of a representative moored FPSO in head seas. This serves to illustrate the failure probabilities actually embedded within current design code methods, and the way in which design methods might be adapted to achieve a specified target safety level.

A comparison of power losses for small (< 1 kW) induction motor drives adopting squarewave and sinusoidal PWM excitation

In this paper the influence of the form of motor excitation on the performance of a small (< 1 kW) induction motor drive is studied. Two forms of excitation, namely sine waves generated by pulse width modulation and simple square wave are explored. Sine wave excitation gives lower motor losses but increases inverter losses. Conversely, square wave excitation increases motor losses but decreases inverter losses. Losses have been measured directly by calorimetric means or, in the case of the inverter, predicted by a Pspice model that has been verified by calorimetric methods. The work shows that overall, the use of square wave excitation leads to a more efficient drive. © 2004 The Institution of Electrical Engineers.

A comparison of losses in small (<1 kW) drives using sine and space vector pulse width modulation schemes

this paper quantifies effects of using three different pulse width modulation (PWM) schemes on the losses in the inverter and induction motor of a 1 kW drive. Direct measurements of losses have been made with a calorimeter. Results show that for the inverter, discontinuous PWM excitation reduces losses by up to 15% compared to sine and symmetrical space vector PWM methods. However, at a low modulation index the greater harmonic content with discontinuous PWM increased motor losses by nearly 20%. This study demonstrates the importance of careful choice of modulation scheme to achieve high overall drive efficiency. © 2005 IEEE.

Comparison of stabilised/solidified mixes of model drill cuttings based on the North Sea and Red Sea Areas

Following the global stringent legislations regulating the wastes generated from the drilling process of oil exploration and production activities, the management of hazardous drill cuttings has become one of the pressing needs confronting the petroleum industry. Most of the prevalent treatment techniques adopted by oil companies are extremely expensive and/or the treated product has to be landfilled without any potential end-use; thereby rendering these solutions unsustainable. The technique of stabilisation/solidification is being investigated in this research to treat drill cuttings prior to landfilling or for potential re-use in construction products. Two case studies were explored namely North Sea and Red Sea. Given the known difficulties with stabilising/solidifying oils and chlorides, this research made use of model drill cutting mixes based on typical drill cutting from the two case studies, which contained 4.2% and 10.95% average concentrations of hydrocarbons; and 2.03% and 2.13% of chlorides, by weight respectively. A number of different binders, including a range of conventional viz. Portland cement (PC) as well as less-conventional viz. zeolite, or waste binders viz. cement kiln dust (CKD), fly ash and compost were tested to assess their ability to treat the North Sea and Red Sea model drill cuttings. The dry binder content by weight was 10%, 20% and 30%. In addition, raw drill cuttings from one of the North Sea offshore rigs were stabilised/solidified using 30% PC. The characteristics of the final stabilised/solidified product were finally compared to those of thermally treated cuttings. The effectiveness of the treatment using the different binder systems was compared in the light of the aforementioned two contaminants only. A set of physical tests (unconfined compressive strength (UCS)), chemical tests (NRA leachability) and micro-structural examinations (using scanning electron microscopy (SEM), and X-ray diffraction (XRD)) were used to evaluate the relative performance of the different binder mixes in treating the drill cuttings. The results showed that the observed UCS covered a wide range of values indicating various feasible end-use scenarios for the treated cuttings within the construction industry. The teachability results showed the reduction of the model drill cuttings to a stable non-reactive hazardous waste, compliant with the UK acceptance criteria for non-hazardous landfills: (a) by most of the 30% and 20% binders for chloride concentrations, and (b) by the 20% and 30% of compost-PC and CKD-PC binders for the Red Sea cuttings. The 20% and 30% compost-PC and CKD-PC binders successfully reduced the leached oil concentration of the North Sea cuttings to inert levels. Copyright 2007, Society of Petroleum Engineers.