Linear sedimentation rates and approximate mass accumulation rates at DSDP Site 61-462

A 560-meter-thick sequence of Cenomanian through Pleistocene sediments cored at DSDP Site 462 in the Nauru Basin overlies a 500-meter-thick complex unit of altered basalt flows, diabase sills, and thin intercalated volcaniclastic sediments. The Upper Cretaceous and Cenozoic sediments contain a high proportion of calcareous fossils, although the site has apparently been below the calcite compensation depth (CCD) from the late Mesozoic to the Pleistocene. This fact and the contemporaneous fluctuations of the calcite and opal accumulation rates suggest an irregular influx of displaced pelagic sediments from the shallow margins of the basin to its center, resulting in unusually high overall sedimentation rates for such a deep (5190 m) site. Shallow-water benthic fossils and planktonic foraminifers both occur as reworked materials, but usually are not found in the same intervals of the sediment section. We interpret this as recording separate erosional interludes in the shallow-water and intermediate-water regimes. Lower and upper Cenozoic hiatuses also are believed to have resulted from mid-water events. High accumulation rates of volcanogenic material during Santonian time suggest a corresponding significant volcanic episode. The coincidence of increased carbonate accumulation rates during the Campanian and displacement of shallow-water fossils during the late Campanian-early Maestrichtian with the volcanic event implies that this early event resulted in formation of the island chains around the Nauru Basin, which then served as platforms for initial carbonate deposition.

Petrology and geochemistry of basalts at DSDP Hole 86-581

Approximately 5 m of aphyric to sparsely phyric basalt was recovered from Hole 581, the only hole on Leg 86 where basement was cored. The occurrence of samples with altered glassy rinds indicates that at least three cooling units (pillows or thin flows) were sampled. The samples were moderately to intensely altered; groundmass crystals are generally fresh, but all glass is altered. Alteration is greatest in vesicular samples, but most of the samples have fractures filled with iron oxyhydroxide, clay, and/or calcite. All 13 samples analyzed are moderately fractionated aluminous N-type mid-ocean ridge basalts. The samples can be divided into two groups based on TiO2 and FeO contents. The least-evolved group may be derived from a more primitive mid-ocean ridge basalt by the crystallization of 18% plagioclase, 24% clinopyroxene, and 3% olivine. The more evolved group may be derived from the first group by the fractionation of 18% plagioclase, 11% clinopyroxene, and 3% olivine. However, higher Ce/Yb ratios in the more evolved group cannot be produced by fractionation and thus we must invoke a more complex process such as dynamic melting to relate the two groups to a common source.

(Table 1) Physical properties of basalts from DSDP Legs 69 and 70

Physical properties of basalts from Deep Sea Drilling Project Sites 504 and 505, south of the Costa Rica Rift, including wet-bulk density, water content, sonic velocity, and thermal conductivity, were measured on board D/V Glomar Challenger during Legs 69 and 70. The mean wet-bulk density is 2.90±0.06 g/cm**3, porosity 5.0±2.2%, sonic velocity 5.75±0.30 km/s, and thermal conductivity 1.67±0.09 W/m°K. Basalts from this young ocean crust (5.9 m.y.) have relatively low porosity and consequently high density and sonic velocity, as compared to average DSDP basalts. Some systematic trends in depth variation of physical properties were found: down to Core 40 in Hole 504B, grain densities were lower than those deeper in the hole, whereas porosity in the upper section was higher. This can be attributed either to differences in the flow type or in the nature of alteration of basalts at the different levels in the hole.

(Appendix) Chemical composition of bottom sediments at DSDP Leg 72 Holes

The distributions of calcium carbonate, of amorphous silica, and of 21 chemical compounds and elements in sediments of Holes 515A, 515B, 516, 516F, 517, and 518 are highly nonuniform; they change depending on the sediment types, grain size, and mineral composition. The main source of the lithogenous elements (K, Li, Rb, Fe, Ti, Zr, Ni, Cr, Sn) is terrigenous matter of South America. These elements correlate well or at least satisfactorily with each other and with the sum of clay minerals. CaCO3, amorphous SiO2 and organic C form a second group, the main source of which is biota of the ocean. Zn, Cu, Ba, Mo, (V, Na) are a third group, which is supplied by both terrigenous and biogenic matter. Judging by the distribution of chemical elements and components in sediments of Site 515, this area of the Brazil Basin is characterized by the rather constant conditions of pelagic terrigenous sedimentation from upper Eocene till Holocene. Small changes in chemical composition of sediments throughout the section are linked mainly to the evolution of subaerial source provinces, changes in hydrodynamic regime, and fluctuations of the ocean level. The chemical composition of sediments from the Rio Grande Rise sites suggests the existence of three main stages of sedimentation in this area. The first stage is the initial period of sediment accumulation on basalts at the beginning of the Late Cretaceous. Then followed sedimentary conditions notable for their sharp changes in chemical composition and type. Beginning in the middle Eocene and persisting into the Holocene, stable conditions of sedimentation characterize a third stage, represented by the formation of approximately 700 m of nannofossil oozes of rather monotonous chemical composition.