Monitoring of centrifugal pump operation by a frequency converter

Centrifugal pumps are widely used in industrial and municipal applications, and they are an important end-use application of electric energy. However, in many cases centrifugal pumps operate with a significantly lower energy efficiency than they actually could, which typically has an increasing effect on the pump energy consumption and the resulting energy costs. Typical reasons for this are the incorrect dimensioning of the pumping system components and inefficiency of the applied pump control method. Besides the increase in energy costs, an inefficient operation may increase the risk of a pump failure and thereby the maintenance costs. In the worst case, a pump failure may lead to a process shutdown accruing additional costs. Nowadays, centrifugal pumps are often controlled by adjusting their rotational speed, which affects the resulting flow rate and output pressure of the pumped fluid. Typically, the speed control is realised with a frequency converter that allows the control of the rotational speed of an induction motor. Since a frequency converter can estimate the motor rotational speed and shaft torque without external measurement sensors on the motor shaft, it also allows the development and use of sensorless methods for the estimation of the pump operation. Still today, the monitoring of pump operation is based on additional measurements and visual check-ups, which may not be applicable to determine the energy efficiency of the pump operation. This doctoral thesis concentrates on the methods that allow the use of a frequency converter as a monitoring and analysis device for a centrifugal pump. Firstly, the determination of energy-efficiency- and reliability-based limits for the recommendable operating region of a variable-speed-driven centrifugal pump is discussed with a case study for the laboratory pumping system. Then, three model-based estimation methods for the pump operating location are studied, and their accuracy is determined by laboratory tests. In addition, a novel method to detect the occurrence of cavitation or flow recirculation in a centrifugal pump by a frequency converter is introduced. Its sensitivity compared with known cavitation detection methods is evaluated, and its applicability is verified by laboratory measurements for three different pumps and by using two different frequency converters. The main focus of this thesis is on the radial flow end-suction centrifugal pumps, but the studied methods can also be feasible with mixed and axial flow centrifugal pumps, if allowed by their characteristics.

Galvaanisen erotuksen toteuttaminen tasavirtasähkönjakelun asiakaspäätelaitteessa

Suomessa sähkönjakeluverkon pääasialliset jännitetasot ovat 20 kV ja 400 V. 20 kV jännitetasolla sähkö viedään lähelle kuluttajia ja muunnetaan pienemmäksi lähellä asiakkaita. Haittapuolena on se, että 20 kV avojohtosähkönsiirtoverkko on hyvin vika-altis ja usein yhden haaran vikaantuessa monta muutakin jää ilman sähköä. Lisäksi hintavien ja suurien jakelumuuntajien määrä on suuri. Vaihtoehtona on toteuttaa osa sähkönjakelusta tasajännitteellä, jolloin tehollinen pienjännite olisi 400 V:a suurempi. Tällöin sähköä voitaisiin siirtää pidempiä matkoja ilman, että asiakaskohtaisia tai muutaman asiakkaan kattavia 20 kV siirtolinjoja tarvitsisi käyttää. Tämä edellyttää vaihtosuuntauksen toteuttamista kuluttajan päässä. Tässä työssä esiteltävällä 1 kVA:n tehoisella vaihtosuuntaajalla muodostetaan tasasähköjakeluverkosta saatavasta 750 V tasasähköstä yksivaiheista (230 VRMS, 50 Hz) verkkojännitettä. Laite on suunniteltu toteuttamaan galvaaninen erotus mahdollisimman hyvällä hyötysuhteella. Suurtaajuusmuuntajan mitoitus mahdollisimman hyvälle hyötysuhteelle on haastava tehtävä, koska vaatimuksia sille asettavat sekä syöttävä resonanssikonvertteri että syötettävä syklokonvertteri. Mitoituksessa on pyrittävä löytämään mahdollisimman hyvä hyötysuhde kustannusten ja toteutettavuuden suhteen.

Frequency-Domain and Wide-Pulse Time-Domain Measurements of Lanthanide Luminescence and Lanthanide-Based Resonance Energy Transfer

Resonance energy transfer (RET) is a non-radiative transfer of the excitation energy from the initially excited luminescent donor to an acceptor. The requirements for the resonance energy transfer are: i) the spectral overlap between the donor emission spectrum and the acceptor absorption spectrum, ii) the close proximity of the donor and the acceptor, and iii) the suitable relative orientations of the donor emission and the acceptor absorption transition dipoles. As a result of the RET process the donor luminescence intensity and the donor lifetime are decreased. If the acceptor is luminescent, a sensitized acceptor emission appears. The rate of RET depends strongly on the donor–acceptor distance (r) and is inversely proportional to r6. The distance dependence of RET is utilized in binding assays. The proximity requirement and the selective detection of the RET-modified emission signal allow homogeneous separation free assays. The term lanthanide-based RET is used when luminescent lanthanide compounds are used as donors. The long luminescence lifetimes, the large Stokes’ shifts and the intense, sharply-spiked emission spectra of the lanthanide donors offer advantages over the conventional organic donor molecules. Both the organic lanthanide chelates and the inorganic up-converting phosphor (UCP) particles have been used as donor labels in the RET based binding assays. In the present work lanthanide luminescence and lanthanide-based resonance energy transfer phenomena were studied. Luminescence lifetime measurements had an essential role in the research. Modular frequency-domain and time-domain luminometers were assembled and used successfully in the lifetime measurements. The frequency-domain luminometer operated in the low frequency domain ( 100 kHz) and utilized a novel dual-phase lock-in detection of the luminescence. One of the studied phenomena was the recently discovered non-overlapping fluorescence resonance energy transfer (nFRET). The studied properties were the distance and temperature dependences of nFRET. The distance dependence was found to deviate from the Förster theory and a clear temperature dependence was observed whereas conventional RET was completely independent of the temperature. Based on the experimental results two thermally activated mechanisms were proposed for the nFRET process. The work with the UCP particles involved the measurement of the luminescence properties of the UCP particles synthesized in our laboratory. The goal of the UCP particle research is to develop UCP donor labels for binding assays. In the present work the effect of the dopant concentrations and the core–shell structure on the total up-conversion luminescence intensity, the red–green emission ratio, and the luminescence lifetime was studied. Also the non-radiative nature of the energy transfer from the UCP particle donors to organic acceptors was demonstrated for the first time in aqueous environment and with a controlled donor–acceptor distance.

Intensity-duration-frequency ratios obtained from annual records and partial duration records in the locality of Pelotas - RS, Brazil

The intensity-duration-frequency occurrence ratio (IDF) is a tool commonly used for precipitation-runoff data transformation, which is established from observations of intense precipitations over a period sufficiently long as to allow the occurrence of extremes at the observation site. This study focused on verifying the existence or absence of new data, in terms of IDF ratio, by using partial duration records produced from data on maximum daily disaggregated rainfall for pre determined durations. The partial duration records considered a base value of 55 mm, totaling 279 values. After the rainfall series were established, their independence and seasonality were assessed. Using the Student's t-test statistics, it was established that no new data, as IDF ratio, emerged from the analysis of the partial duration series with the recommended base value of precipitation, as compared to the historical records.

Analysis of the relationship intensity, duration, frequency of disaggregated daily rainfall in southern Rio Grande do Sul, Brazil

The intensity, duration, and frequency relationship (IDF) of rainfall occurrence may be done through continuous records of pluviographs or daily pluviometer values . The objective of this study was to estimate the intensity-duration-frequency relationships of precipitation, using the method of daily rainfall disaggregation, at weather stations located to the southern half of the state of Rio Grande do Sul; comparing them with those obtained by rain gauge records, in places considered homogeneous from the meteorological point of view. The IDF equation parameters were estimated from daily rainfall disaggregation data, using the method of nonlinear optimization. To validate the equations confidence indices and efficiency and the "t" Student test, among maximum intensity values obtained from the disaggregated daily rainfall durations of 10; 30; 60 min and 6; 12 and 24 h and those extracted from existing IDF equations. For all studied stations and return periods, the trust index values were regarded as "optimal", i.e., greater than 0.85. The maximal intensity of rainfall obtained by daily rainfall disaggregation have similarity with those obtained by relations IDF standards. Thus, the method constitutes a feasible alternative in obtaining the IDF relationships.

Method adjustment and equation set of maximum rainfall intensity, duration and frequency in the Mato Grosso do Sul State

Due to the lack of information concerning maximum rainfall equations for most locations in Mato Grosso do Sul State, the alternative for carrying out hydraulic work projects has been information from meteorological stations closest to the location in which the project is carried out. Alternative methods, such as 24 hours rain disaggregation method from rainfall data due to greater availability of stations and longer observations can work. Based on this approach, the objective of this study was to estimate maximum rainfall equations for Mato Grosso do Sul State by adjusting the 24 hours rain disaggregation method, depending on data obtained from rain gauge stations from Dourado and Campo Grande. For this purpose, data consisting of 105 rainfall stations were used, which are available in the ANA (Water Resources Management National Agency) database. Based on the results we concluded: the intense rainfall equations obtained by pluviogram analysis showed determination coefficient above 99%; and the performance of 24 hours rain disaggregation method was classified as excellent, based on relative average error WILMOTT concordance index (1982).

Loss Modelling of Three-Level Inverters controlled with Space Vector Modulation Technique

The objective of this master’s thesis is to investigate the loss behavior of three-level ANPC inverter and compare it with conventional NPC inverter. The both inverters are controlled with mature space vector modulation strategy. In order to provide the comparison both accurate and detailed enough NPC and ANPC simulation models should be obtained. The similar control model of SVM is utilized for both NPC and ANPC inverter models. The principles of control algorithms, the structure and description of models are clarified. The power loss calculation model is based on practical calculation approaches with certain assumptions. The comparison between NPC and ANPC topologies is presented based on results obtained for each semiconductor device, their switching and conduction losses and efficiency of the inverters. Alternative switching states of ANPC topology allow distributing losses among the switches more evenly, than in NPC inverter. Obviously, the losses of a switching device depend on its position in the topology. Losses distribution among the components in ANPC topology allows reducing the stress on certain switches, thus losses are equally distributed among the semiconductors, however the efficiency of the inverters is the same. As a new contribution to earlier studies, the obtained models of SVM control, NPC and ANPC inverters have been built. Thus, this thesis can be used in further more complicated modelling of full-power converters for modern multi-megawatt wind energy conversion systems.

Active inverter output filtering methods

Frequency converters are widely used in the industry to enable better controllability and efficiency of variable speed AC motor drives. Despite these advantages, certain challenges concerning the inverter and motor interfacing have been present for decades. As insulated gate bipolar transistors entered the market, the inverter output voltage transition rate significantly increased compared with their predecessors. Inverters operate based on pulse width modulation of the output voltage, and the steep voltage edge fed by the inverter produces a motor terminal overvoltage. The overvoltage causes extra stress to the motor insulation, which may lead to a prematuremotor failure. The overvoltage is not generated by the inverter alone, but also by the sum effect of the motor cable length and the impedance mismatch between the cable and the motor. Many solutions have been shown to limit the overvoltage, and the mainstream products focus on passive filters. This doctoral thesis studies an alternative methodology for motor overvoltage reduction. The focus is on minimization of the passive filter dimensions, physical and electrical, or better yet, on operation without any filter. This is achieved by additional inverter control and modulation. The studied methods are implemented on different inverter topologies, varying in nominal voltage and current.For two-level inverters, the studied method is termed active du/dt. It consists of a small output LC filter, which is controlled by an independent modulator. The overvoltage is limited by a reduced voltage transition rate. For multilevel inverters, an overvoltage mitigation method operating without a passive filter, called edge modulation, is implemented. The method uses the capability of the inverter to produce two switching operations in the same direction to cancel the oscillating voltages of opposite phases. For parallel inverters, two methods are studied. They are both intended for two-level inverters, but the first uses individual motor cables from each inverter while the other topology applies output inductors. The overvoltage is reduced by interleaving the switching operations to produce a similar oscillation accumulation as with the edge modulation. The implementation of these methods is discussed in detail, and the necessary modifications to the control system of the inverter are presented. Each method is experimentally verified by operating industrial frequency converters with the modified control. All the methods are found feasible, and they provide sufficient overvoltage protection. The limitations and challenges brought about by the methods are discussed.

Tasasähkönjakeluverkon vaihtosuuntaajan pulssintiheysmoduloidun pääteasteen ja prototyypin toteutus

Työssä esiteltävä laite on osa DC-AC hakkuria, jolla muodostetaan 750 V tasajännitteestä yksivaiheista (230 VRMS, 50 Hz) galvaanisesti erotettua verkkojännitettä. Tasajännite muunnetaan resonanssikonvertterilla korkeataajuiseksi vaihtojännitteeksi, joka johdetaan erotusmuuntajaan. Galvaanisen erotuksen jälkeen korkeataajuisesta vaihtojännitteestä muodostetaan suoraan verkkotaajuista vaihtojännitettä työssä esiteltävällä syklokonvertterilla. Suunnittelussa on pyritty minimoimaan häviöt mahdollisimman tarkkaan, jotta laite olisi kilpailukykyinen ei-galvaanisesti erottavien konverttereiden kanssa. Tämä on toteutettu käyttämällä mahdollisimman vähän komponentteja virran kulkureitillä sekä soveltamalla pehmeää kytkentää kaikissa tilanteissa. Lopuksi esitellään prototyyppi, jonka tarkoitus oli selvittää laitteen toiminta ja ongelmakohdat käytännössä.

Comparative analysis of the frequency and the severity of diagnosed lesions between pedestrians struck by motor vehicles and other blunt trauma mechanisms victims

ABSTRACTObjective:to compare the frequency and the severity of diagnosed injuries between pedestrians struck by motor vehicles and victims of other blunt trauma mechanisms.Methods:retrospective analysis of data from the Trauma Registry, including adult blunt trauma patients admitted from 2008 to 2010. We reviewed the mechanism of trauma, vital signs on admission and the injuries identified. Severity stratification was carried using RTS, AIS-90, ISS e TRISS. Patients were assigned into group A (pedestrians struck by motor vehicle) or B (victims of other mechanisms of blunt trauma). Variables were compared between groups. We considered p<0.05 as significant.Results:a total of 5785 cases were included, and 1217 (21,0%) of which were in group A. Pedestrians struck by vehicles presented (p<0.05) higher mean age, mean heart rate upon admission, mean ISS and mean AIS in head, thorax, abdomen and extremities, as well as lower mean Glasgow coma scale, arterial blood pressure upon admission, RTS and TRISS. They also had a higher frequency of epidural hematomas, subdural hematomas, subarachnoid hemorrhage, brain swelling, cerebral contusions, costal fractures, pneumothorax, flail chest, pulmonary contusions, as well as pelvic, superior limbs and inferior limbs fractures.Conclusion:pedestrian struck by vehicles sustained intracranial, thoracic, abdominal and extremity injuries more frequently than victims of other blunt trauma mechanism as a group. They also presented worse physiologic and anatomic severity of the trauma.

Sähköavusteisen polkupyörän vääntömomenttisäädön toteuttaminen amplitudimodulaatiolla

Sähköavusteinen polkupyörä on hieman tavallista polkupyörää vahvarakenteisempi ja painavampi. Lisäpainoa tuovat muun muassa akut ja sähkömoottori, joka avustaa polke-mista. Moottori asennetaan yleensä eturenkaan keskiöön. Suurimmassa osassa, jollei kaikissa, kaupallisista sähköavusteisissa polkupyörissä moottori on hiiliharjaton tasavirta-moottori. Hiiliharjattoman tasavirtamoottorin pyörimisnopeutta ja vääntömomenttia voidaan säätää usealla eri tavalla. Markkinoilla olevat säätimet perustuvat poikkeuksetta pulssinleveys-modulaatioon. Tämän työn tarkoituksena on tutkia, onko säätöjärjestelmä mahdollista to-teuttaa muulla tavalla kuin pulssinleveysmodulaattorilla. Tutkimuksessa päädytään käyt-tämään amplitudimodulointia, jolloin taajuus voidaan pitää vakiona. Tämän tutkimuksen rinnalla samaan polkupyörään rakennetaan polkemisenergian avulla akkuja lataava la-tausjärjestelmä. Tämän kandityön puitteissa tutkimus jää kesken, mutta toiminta osoitetaan teoreettisesti ja simuloimalla. Suurin syy kokeellisen testauksen epäonnistumiseen on käytettyjen kom-ponenttien sopimattomuus sovellukseen.

Frequency of fear of needles and impact of a multidisciplinary educational approach towards pregnant women with diabetes

PURPOSE: To evaluate the frequency of fear of needles and the impact of a multidisciplinary educational program in women with pre-gestational and gestational diabetes taking insulin during pregnancy. METHODS: The short Diabetes Fear of Injecting and Self-testing Questionnaire (D-FISQ), composed by two subscales that access fear of self injection (FSI) and fear of self testing (FST), was administered twice during pregnancy to 65 pregnant women with pre-gestational and gestational diabetes: at the first endocrine consult and within the last two weeks of pregnancy or postpartum. An organized multidisciplinary program provided diabetes education during pregnancy. Statistical analysis was carried out by Wilcoxon and McNemar tests and Spearman correlation. A p<0.05 was considered to be significant. RESULTS: Data from the short D-FISQ questionnaire shows that 43.1% of pregnant women were afraid of needles in the first evaluation. There was a significant reduction in scores for FSI and FST subscales between the first and second assessments (first FSI 38.5% compared with second 12.7%, p=0.001; first FST 27.7% compared with second FST 14.3%, p=0.012). CONCLUSIONS: The fear of needles is common in pregnant women on insulin therapy and an organized multidisciplinary educational diabetes program applied during pregnancy reduces scores of such fear.

Accuracy Analysis of Frequency Converter Estimates in Diagnostic Applications

Transportation of fluids is one of the most common and energy intensive processes in the industrial and HVAC sectors. Pumping systems are frequently subject to engineering malpractice when dimensioned, which can lead to poor operational efficiency. Moreover, pump monitoring requires dedicated measuring equipment, which imply costly investments. Inefficient pump operation and improper maintenance can increase energy costs substantially and even lead to pump failure. A centrifugal pump is commonly driven by an induction motor. Driving the induction motor with a frequency converter can diminish energy consumption in pump drives and provide better control of a process. In addition, induction machine signals can also be estimated by modern frequency converters, dispensing with the use of sensors. If the estimates are accurate enough, a pump can be modelled and integrated into the frequency converter control scheme. This can open the possibility of joint motor and pump monitoring and diagnostics, thereby allowing the detection of reliability-reducing operating states that can lead to additional maintenance costs. The goal of this work is to study the accuracy of rotational speed, torque and shaft power estimates calculated by a frequency converter. Laboratory tests were performed in order to observe estimate behaviour in both steady-state and transient operation. An induction machine driven by a vector-controlled frequency converter, coupled with another induction machine acting as load was used in the tests. The estimated quantities were obtained through the frequency converter’s Trend Recorder software. A high-precision, HBM T12 torque-speed transducer was used to measure the actual values of the aforementioned variables. The effect of the flux optimization energy saving feature on the estimate quality was also studied. A processing function was developed in MATLAB for comparison of the obtained data. The obtained results confirm the suitability of this particular converter to provide accurate enough estimates for pumping applications.

Localization, Frequency, and Functions of Filled Pauses: Five American Politicians’ Use of er and erm in the Talk Show Larry King Live

Tämän pro gradu– tutkielman tavoitteena oli testata täytettyjen taukojen (er ja erm) esiintymistiheyttä, sijaintia kieliopillisessa rakenteessa sekä funktioita Kjellmerin (2003) korpus-tutkimuksessa. Materiaalina käytin viiden yhdysvaltalaisen poliitikon puhetta keskusteluohjelmasta Larry King Live. Tutkimuksessani sovelsin Kjellmerin tutkimusmenetelmiä, joita muokkasin huomattavasti suppeampaan materiaaliini sopiviksi. Lähestymistapani oli täten induktiivinen toisin kuin testatussa tutkimuksessa. Materiaalini oli tarkoituksellisesti rajattu, sillä halusin selvittää, kuvaavatko Kjellmerin laajaan materiaaliin perustuvat tutkimustulokset myös täytettyjen taukojen käyttöä suppeammassa materiaalissa. Materiaalini (kokonaisuudessaan 101 minuuttia) transkriboin ortografisesti. Analyysissäni arvioin täytettyjen taukojen esiintymistiheyden puhujakohtaisesti ja koko ryhmälle suhteuttamalla täytettyjen taukojen lukumäärän kokonaissanamäärään. Tämän jälkeen tein perinteisen kielioppianalyysin rakenteista, joita edeltää tai joissa esiintyy täytetty tauko, ja täytettyjen taukojen sijainnin perusteella luokittelin ne sana-, lauseke-, ja lausetasolle. Lopuksi analysoin täytettyjen taukojen käyttöä soveltaen Kjellmerin ehdottamia funktioita (hesitaatio, vuorottelujäsennyksen merkitseminen, huomion herättäminen ja kontaktin luominen, korostus ja korjaus) ja niiden piirteitä omaan materiaaliini. Tutkimukseni perusteella täytetyt tauot esiintyvät tutkitun viiden poliitikon puheessa suhteellisen usein. Puhujakohtaiset eroavaisuudet olivat kuitenkin huomattavat. Kieliopillisen luokitteluni mukaan sana-, lauseke- ja lausetasot eivät täysin kuvaa täytettyjen taukojen sijoittumista, sillä täytetyt tauot edelsivät mm. määre-lauseita, jotka eivät vastaa lausetasoa englannin kielessä. Materiaalini funktioanalyysi osoitti, että täytetyt tauot yleensä vastaavat yhtä tai useampaa Kjellmerin ehdottamaa funktioita. Lisäksi tutkimukseni mukaan täytetyillä tauoilla on ainakin yksi rakenteellinen funktio. Analyysini perusteella Kjellmerin tutkimustulokset ovat siis pääosin sovellettavissa suppeampaan materiaaliin. Puutteiksi hänen tutkimuksessaan osoittautuivat funktioanalyysille tärkeän kontekstuaalisen informaation puute sekä keskittyminen täytettyihin taukoihin, jotka esiintyvät vain tietyissä kielioppirakenteissa. Yleisesti voin tutkimukseni pohjalta todeta, että täytetyt tauot ovat vielä vajaasti tunnettuja ja että kieliopillisen sijoituksen ja funktioiden lisätutkimus on tarpeellista.

Matched case-control study evaluating the frequency of the main agents associated with neonatal diarrhea in piglets

A case-control study was carried out in litters of 1 to 7-day-old piglets to identify the main infectious agents involved with neonatal diarrhea in pigs. Fecal samples (n=276) from piglets were collected on pig farms in the State of Rio Grande do Sul, Brazil, from May to September 2007. Litters with diarrhea were considered cases (n=129) and normal litters (n=147) controls. The samples were examined by latex agglutination test, PAGE, conventional isolating techniques, ELISA, PCR, and microscopic methods in order to detect rotavirus, bacterial pathogens (Escherichia coli, Clostridium perfringens type A and C, and Clostridium difficile), and parasites (Coccidian and Cryptosporidium spp.). Outbreaks of diarrhea were not observed during sampling. At least one agent was detected in fecal samples on 25 out of 28 farms (89.3%) and in 16 farms (57.1%) more than one agent was found. The main agents diagnosed were Coccidia (42.86%) and rotavirus (39.29%). The main agents identified in litters with diarrhea were Clostridium difficile (10.6%), Clostridium perfringens type A (8.8%) and rotavirus (7.5%); in control litters, Clostridium difficile (16.6%) and Coccidian (8.5%). Beta hemolytic Escherichia coli and Clostridium perfringens type C were not detected. When compared with controls, no agent was significantly associated with diarrhea in case litters. These findings stress the need for caution in the interpretation of laboratorial diagnosis of mild diarrhea in neonatal pigs, as the sole detection of an agent does not necessarily indicate that it is the cause of the problem.