Sandwich enzyme immunoassay using three monoclonal antibodies against different epitopes of carcinoembryonic antigen (CEA).

Purified monoclonal antibodies (Mab) produced by 3 hybridomas and reacting with 3 different epitopes of carcinoembryonic antigen (CEA) were used in a solid phase enzyme immunoassay. Two Mabs were physically adsorbed to polystyrene balls and the third Mab was coupled to alkaline phosphatase using the bifunctional reagent N-succinimidyl-3-(2-pyridyldithio)-propionate. During a first incubation, CEA from heat-extracted serum samples was immunoadsorbed to the antibody coated balls. After washing of the balls, bound CEA was detected by a second incubation with the enzyme coupled Mab. The sensitivity of the assay was 0.6 ng per ml of serum. A total of 196 serum samples from patients with various types of carcinoma, with liver cirrhosis, or from healthy blood donors with or without smoking habits, were tested. The results obtained with the monoclonal enzyme immunoassay (M-EIA) were compared with those obtained with perchloric acid extracts of the same serum samples tested by an inhibition radioimmunoassay using conventional goat anti-CEA antiserum. There was an excellent correlation between the two assays. In particular, the new M-EIA gave good results for the detection of tumor recurrences in the follow-up of colon carcinoma patients. However, despite the use of exclusively monoclonal antibodies the new assay detected a similar percentage of slightly elevated CEA values as the conventional assay in patients with non-malignant disease, suggesting that the CEA associated with non-malignant diseases is immunologically identical to the CEA released by colon carcinoma.

Alterations in Postural Control during the World's Most Challenging Mountain Ultra-Marathon

We investigated postural control (PC) effects of a mountain ultra-marathon (MUM): a 330-km trail run with 24000 m of positive and negative change in elevation. PC was assessed prior to (PRE), during (MID) and after (POST) the MUM in experienced ultra-marathon runners (n = 18; finish time = 126+/-16 h) and in a control group (n = 8) with a similar level of sleep deprivation. Subjects were instructed to stand upright on a posturographic platform over a period of 51.2 seconds using a double-leg stance under two test conditions: eyes open (EO) and eyes closed (EC). Traditional measures of postural stability (center of pressure trajectory analysis) and stabilogram-diffusion analysis (SDA) parameters were analysed. For the SDA, a significantly greater short-term effective diffusion was found at POST compared with PRE in the medio-lateral (ML; Dxs) and antero-posterior (AP) directions (Dys) in runners (p<0.05) The critical time interval (Ctx) in the ML direction was significantly higher at MID (p<0.001) and POST (p<0.05) than at PRE in runners. At MID (p<0.001) and POST (p<0.05), there was a significant difference between the two groups. The critical displacement (Cdx) in the ML was significantly higher at MID and at POST (p<0.001) compared with PRE for runners. A significant difference in Cdx was observed between groups in EO at MID (p<0.05) and POST (p<0.005) in the ML direction and in EC at POST in the ML and AP directions (p<0.05). Our findings revealed significant effects of fatigue on PC in runners, including, a significant increase in Ctx (critical time in ML plan) in EO and EC conditions. Thus, runners take longer to stabilise their body at POST than at MID. It is likely that the mountainous characteristics of MUM (unstable ground, primarily uphill/downhill running, and altitude) increase this fatigue, leading to difficulty in maintaining balance.

Detection of millimetric deformation using a terrestrial laser scanner: experiment and application to a rockfall event

Terrestrial laser scanning (TLS) is one of the most promising surveying techniques for rockslope characterization and monitoring. Landslide and rockfall movements can be detected by means of comparison of sequential scans. One of the most pressing challenges of natural hazards is combined temporal and spatial prediction of rockfall. An outdoor experiment was performed to ascertain whether the TLS instrumental error is small enough to enable detection of precursory displacements of millimetric magnitude. This consists of a known displacement of three objects relative to a stable surface. Results show that millimetric changes cannot be detected by the analysis of the unprocessed datasets. Displacement measurement are improved considerably by applying Nearest Neighbour (NN) averaging, which reduces the error (1¿) up to a factor of 6. This technique was applied to displacements prior to the April 2007 rockfall event at Castellfollit de la Roca, Spain. The maximum precursory displacement measured was 45 mm, approximately 2.5 times the standard deviation of the model comparison, hampering the distinction between actual displacement and instrumental error using conventional methodologies. Encouragingly, the precursory displacement was clearly detected by applying the NN averaging method. These results show that millimetric displacements prior to failure can be detected using TLS.

Non-conventional water resources in coastal areas: a review of the use of reclaimed water

In an era of increasing concern for limited water resources a wise joint management of conventional and nonconventional water resources must be considered. Water scarcity aggravates in coastal zones which are often characterised by high population density, intense economic activity and tourism; meaning heavy seasonal water demands. The relationships between sea and land-water can also compromise the quality of available freshwater. In this context, the use of non-conventional water increases the availability of water supplies. Non-conventional water resources of low quality could be directed to meet several needs (like watering lawns, washing cars, flushing toilets and cooling systems, among others). Therefore, significantly more potable water would be available to meet human demand for safe water.

Ultrastructure of adhesion and movement of the tetraspores of Gelidium Lamour (Geldiaceae; Rhodophyta)

The outer part of the tetraspora cell wall in Gelidium crinale (Turner) J.V. Lamour. and G. spathulatum (Kutz.) Bornet is morphologically described in relation to the movements and displacement of these spores when they settle on a substratum. We also describe the mechanism of adhesión and the transformations undergone by this mechanism over time. The cell wall shows a network of fibrillar threads embedded in abundant mucilage. The deformations that tetraspores undergo show that the cell wall is relatively elastic.

Inverse metamorphic zonation in very low-grade Tibetan zone series of SE Zanskar and its tectonic consequences (NW India, Himalaya)

The metamorphism of the carbonate rocks of the SE Zanskar Tibetan zone has been studied by `'illite crystallinity'' and calcite-dolomite thermometry. The epizonal Zangla unit overlies the anchizonal Chumik unit. This discontinuous inverse zonation demonstrates a late to post-metamorphic thrust of the first unit over the second. The studied area underwent a complex tectonic history: - The tectonic units were stacked from the NE to the SW, generating recumbent folds, NE dipping thrusts and the regional metamorphism. The compressive movements were active under lower temperature conditions, resulting in late thrusts that disturbed the metamorphic zonation. The discontinuous inverse metamorphic zonation dates from this phase. - A NE vergent backfolding phase occurred at lower temperature conditions. It caused the uplift of more metamorphic levels. - A late extensional phase is revealed by the presence of NE dipping low angle normal faults, and a major high angle fault, the Sarchu fault. The low angle normal faults locally run along earlier thrusts (composite tectonic contacts). Their throw has been sufficient to reset a normal stratigraphic superposition (young layers overlying old ones), but insufficient to erase the inverse metamorphic relationship. However, the combined action of backfolding and normal faulting can locally lessen, or even cancel, the inverse metamorphic superposition. After deduction of the normal fault translation, the vertical component of the original thrust displacement through stratigraphy is 400 m, which is a value far too low to explain the temperature difference between the two units. The horizontal component of displacement is therefore far more important than the vertical one. The regional distribution of metamorphism within the Zangla unit points out to an anchizonal front and an epizonal inner part. This fact is in agreement with nappe tectonics.

Fast Geodesic Active Fields for Image Registration Based on Splitting and Augmented Lagrangian Approaches.

In this paper, we present an efficient numerical scheme for the recently introduced geodesic active fields (GAF) framework for geometric image registration. This framework considers the registration task as a weighted minimal surface problem. Hence, the data-term and the regularization-term are combined through multiplication in a single, parametrization invariant and geometric cost functional. The multiplicative coupling provides an intrinsic, spatially varying and data-dependent tuning of the regularization strength, and the parametrization invariance allows working with images of nonflat geometry, generally defined on any smoothly parametrizable manifold. The resulting energy-minimizing flow, however, has poor numerical properties. Here, we provide an efficient numerical scheme that uses a splitting approach; data and regularity terms are optimized over two distinct deformation fields that are constrained to be equal via an augmented Lagrangian approach. Our approach is more flexible than standard Gaussian regularization, since one can interpolate freely between isotropic Gaussian and anisotropic TV-like smoothing. In this paper, we compare the geodesic active fields method with the popular Demons method and three more recent state-of-the-art algorithms: NL-optical flow, MRF image registration, and landmark-enhanced large displacement optical flow. Thus, we can show the advantages of the proposed FastGAF method. It compares favorably against Demons, both in terms of registration speed and quality. Over the range of example applications, it also consistently produces results not far from more dedicated state-of-the-art methods, illustrating the flexibility of the proposed framework.

Pile Design and Tests for Integral Abutment Bridges, HR-273, 1987

Expansion joints increase both the initial cost and the maintenance cost of bridges. Integral abutment bridges provide an attractive design alternative because expansion joints are eliminated from the bridge itself. However, the piles in these bridges are subjected to horizontal movement as the bridge expands and contracts during temperature changes. The objective of this research was to develop a method of designing piles for these conditions. Separate field tests simulating a pile and a bridge girder were conducted for three loading cases: (1) vertical load only, (2) horizontal displacement of pile head only, and (3) combined horizontal displacement of pile head with subsequent vertical load. Both tests (1) and (3) reached the same ultimate vertical load, that is, the horizontal displacement had no effect on the vertical load capacity. Several model tests were conducted in sand with a scale factor of about 1:10. Experimental results from both the field and model tests were used to develop the vertical and horizontal load-displacement properties of the soil. These properties were input into the finite element computer program Integral Abutment Bridge Two-Dimensional (IAB2D), which was developed under a previous research contract. Experimental and analytical results compared well for the test cases. Two alternative design methods, both based upon the American Association of State Highway and Transportation Officials (AASHTO) Specification, were developed. Alternative One is quite conservative relative to IAB2D results and does not permit plastic redistribution of forces. Alternative Two is also conservative when compared to IAB2D, but plastic redistribution is permitted. To use Alternative Two, the pile cross section must have sufficient inelastic rotation capacity before local buckling occurs. A design example for a friction pile and an end-bearing pile illustrates both alternatives.

Preventing Cracking at Diaphragm/Plate Girder Connections in Steel Bridges, HR-393, 1998

Some of the Iowa Department of Transportation (Iowa DOT) continuous, steel, welded plate girder bridges have developed web cracking in the negative moment regions at the diaphragm connection plates. The cracks are due to out-of-plane bending of the web near the top flange of the girder. The out-of-plane bending occurs in the "web-gap", which is the portion of the girder web between (1) the top of the fillet welds attaching the diaphragm connection plate to the web and (2) the fillet welds attaching the flange to the web. A literature search indicated that four retrofit techniques have been suggested by other researchers to prevent or control this type of cracking. To eliminate the problem in new bridges, AASHTO specifications require a positive attachment between the connection plate and the top (tension) flange. Applying this requirement to existing bridges is expensive and difficult. The Iowa DOT has relied primarily on the hole-drilling technique to prevent crack extension once cracking has occurred; however, the literature indicates that hole-drilling alone may not be entirely effective in preventing crack extension. The objective of this research was to investigate experimentally a method proposed by the Iowa DOT to prevent cracking at the diaphragm/plate girder connection in steel bridges with X-type or K-type diaphragms. The method consists of loosening the bolts at some connections between the diaphragm diagonals and the connection plates. The investigation included selecting and testing five bridges: three with X-type diaphragms and two with K-type diaphragms. During 1996 and 1997, these bridges were instrumented using strain gages and displacement transducers to obtain the response at various locations before and after implementing the method. Bridges were subjected to loaded test trucks traveling in different lanes with speeds varying from crawl speed to 65 mph (104 km/h) to determine the effectiveness of the proposed method. The results of the study show that the effect of out-of-plane loading was confined to widths of approximately 4 in. (100 mm) on either side of the connection plates. Further, they demonstrate that the stresses in gaps with drilled holes were higher than those in gaps without cracks, implying that the drilling hole technique is not sufficient to prevent crack extension. The behavior of the web gaps in X-type diaphragm bridges was greatly enhanced by the proposed method as the stress range and out-of-plane distortion were reduced by at least 42% at the exterior girders. For bridges with K-type diaphragms, a similar trend was obtained. However, the stress range increased in one of the web gaps after implementing the proposed method. Other design aspects (wind, stability of compression flange, and lateral distribution of loads) must be considered when deciding whether to adopt the proposed method. Considering the results of this investigation, the proposed method can be implemented for X-type diaphragm bridges. Further research is recommended for K-type diaphragm bridges.

Supracerebellar arachnoid cyst - A rare cause of acquired Chiari I malformation.

Chiari I malformation (CM) associated with a cervico-thoracic syrinx due to supracerebellar arachnoid cyst has not been reported in the literature. We report such a case, managed by fenestration of the arachnoid cyst and foramen magnum decompression (FMD), aiming to reduce the inferiorly directed pressure on the cerebellum and eliminate the craniospinal pressure dissociation respectively. Imaging done post-operatively showed upward displacement of the cerebellar tonsils with a decompressed craniovertebral junction and disappearance of the syrinx.

Validation of Design Recommendations for Integral Abutment Piles, HR-292, 1989

Since integral abutment bridges decrease the initial and maintenance costs of bridges, they provide an attractive alternative for bridge designers. The objective of this project is to develop rational and experimentally verified design recommendations for these bridges. Field testing consisted of instrumenting two bridges in Iowa to monitor air and bridge temperatures, bridge displacements, and pile strains. Core samples were also collected to determine coefficients of thermal expansion for the two bridges. Design values for the coefficient of thermal expansion of concrete are recommended, as well as revised temperature ranges for the deck and girders of steel and concrete bridges. A girder extension model is developed to predict the longitudinal bridge displacements caused by changing bridge temperatures. Abutment rotations and passive soil pressures behind the abutment were neglected. The model is subdivided into segments that have uniform temperatures, coefficients of expansion, and moduli of elasticity. Weak axis pile strains were predicted using a fixed-head model. The pile is idealized as an equivalent cantilever with a length determined by the surrounding soil conditions and pile properties. Both the girder extension model and the fixed-head model are conservative for design purposes. A longitudinal frame model is developed to account for abutment rotations. The frame model better predicts both the longitudinal displacement and weak axis pile strains than do the simpler models. A lateral frame model is presented to predict the lateral motion of skewed bridges and the associated strong axis pile strains. Full passive soil pressure is assumed on the abutment face. Two alternatives for the pile design are presented. Alternative One is the more conservative and includes thermally induced stresses. Alternative Two neglects thermally induced stresses but allows for the partial formation of plastic hinges (inelastic redistribution of forces). Ductility criteria are presented for this alternative. Both alternatives are illustrated in a design example.

Assessment of vascular invasion by bone and soft tissue tumours of the limbs: usefulness of MDCT angiography.

OBJECTIVE: To evaluate the accuracy of computed tomography angiography (CTA) in predicting arterial encasement by limb tumours, by comparing CTA with surgical findings (gold standard). METHODS: Preoperative CTA images of 55 arteries in 48 patients were assessed for arterial status: cross-sectional CTA images were scored as showing a fat plane between artery and tumour (score 0), slight contact between artery and tumour (score 1), partial arterial encasement (score 2) or total arterial encasement (score 3). Reformatted CTA images were assessed for arterial displacement, rigid wall, stenosis or occlusion. At surgery, arteries were classified as free or surgically encased; 45 arteries were free and 10 were surgically encased. RESULTS: Multivariate logistic regression identified the axial CTA score as a relevant predictor for arterial encasement and subsequent vascular intervention during surgery. All sites where CTA showed a fat plane between the tumour and the artery were classified as free at surgery (n = 28/28). The sensitivity of total arterial encasement on CTA (score 3) was 90%, specificity 93%, accuracy 93% and positive likelihood ratio 13.5. CONCLUSION: CTA evidence of total arterial encasement is a highly specific indication of arterial encasement. The presence of fat between the tumour and the artery on CTA rules out arterial involvement at surgery.

Direct three-dimensional myocardial strain tensor quantification and tracking using zHARP.

Images of myocardial strain can be used to diagnose heart disease, plan and monitor treatment, and to learn about cardiac structure and function. Three-dimensional (3D) strain is typically quantified using many magnetic resonance (MR) images obtained in two or three orthogonal planes. Problems with this approach include long scan times, image misregistration, and through-plane motion. This article presents a novel method for calculating cardiac 3D strain using a stack of two or more images acquired in only one orientation. The zHARP pulse sequence encodes in-plane motion using MR tagging and out-of-plane motion using phase encoding, and has been previously shown to be capable of computing 3D displacement within a single image plane. Here, data from two adjacent image planes are combined to yield a 3D strain tensor at each pixel; stacks of zHARP images can be used to derive stacked arrays of 3D strain tensors without imaging multiple orientations and without numerical interpolation. The performance and accuracy of the method is demonstrated in vitro on a phantom and in vivo in four healthy adult human subjects.

Smart instrumentation for determination of ligament stiffness and ligament balance in total knee arthroplasty.

Ligament balance is an important and subjective task performed during total knee arthroplasty (TKA) procedure. For this reason, it is desirable to develop instruments to quantitatively assess the soft-tissue balance since excessive imbalance can accelerate prosthesis wear and lead to early surgical revision. The instrumented distractor proposed in this study can assist surgeons on performing ligament balance by measuring the distraction gap and applied load. Also the device allows the determination of the ligament stiffness which can contribute a better understanding of the intrinsic mechanical behavior of the knee joint. Instrumentation of the device involved the use of hall-sensors for measuring the distractor displacement and strain gauges to transduce the force. The sensors were calibrated and tested to demonstrate their suitability for surgical use. Results show the distraction gap can be measured reliably with 0.1mm accuracy and the distractive loads could be assessed with an accuracy in the range of 4N. These characteristics are consistent with those have been proposed, in this work, for a device that could assist on performing ligament balance while permitting surgeons evaluation based on his experience. Preliminary results from in vitro tests were in accordance with expected stiffness values for medial collateral ligament (MCL) and lateral collateral ligament (LCL).

Fluid-rock interaction during late stages of the Alpine exhumation

Résumé de la thèseLa fracturation des roches au cours de phases compressives ou extensives est un souvent évoquée pour expliquer la circulation de fluide au sein des roches cristallines. Dans le cadre de cette thèse, la circulation des fluides lors de l'exhumation tardive des Alpes a été étudiée en utilisant deux approches différentes: analyses structurales de la déformation fragile d'une part et analyses géochimiques des roches et des minéraux (isotopes stables, datations U/Pb, thermochronologie (U-Th)/He) d'autre part. Cette approche combinée a permis de mieux comprendre l'interaction existante entre les fluides métamorphiques et les fluides météoriques, ainsi que leur interaction avec les roches encaissantes. Le travail a été effectué dans la zone Pennique du Valais suisse.La première partie était focalisée sur la déformation fragile, le but étant de définir les différents types de déformations existantes et de déterminer l'âge relatif des différentes familles de failles. Dans la région d'étude, quatre domaines ont été distingués. Chacun d'eux comportent deux types de structures fragiles, certaines sont minéralisées alors que d'autre non. Au sein de chaque domaine, la direction principale des structures minéralisées correspond à l'orientation des accidents tectoniques majeurs de la région (Aosta- Ranzola Line au Sud, Rhône Line au Nord et Simplon Fault Zone à l'Est), alors que les structures non- minéralisées montrent des orientations plus variables. Ainsi, le premier type de structure est interprété comme résultant d'une dislocation tectonique alors que le deuxième type de structure résulterait d'une dislocation gravitaire locale. Il n'est néanmoins pas possible de classer chronologiquement la formation de ces deux types de structure ni d'attribuer un âge relatif aux changements d'orientation des contraintes majeures.La deuxième étude a été effectuée dans la région de la zone de faille du Simplon. Dans cette zone, la composition isotopique des minéraux ayant cristallisé à l'intérieur des fractures tardives permet de distinguer différents types de circulation de fluide. Les valeurs δ180 du quartz de la roche encaissante ainsi que ceux des veines tardives du bloque inférieur de la faille sont comparables. Ces valeurs indiquent un rééquilibrage et un tamponnage isotopique des fluides tardifs au contact de la roche encaissante lors de la fracturation de cette dernière et de la cristallisation des veines tardives. La même situation est observée dans la partie nord du bloque supérieur ainsi que dans sa partie sud. Ceci n'est néanmoins pas le cas pour la partie centrale du bloque supérieur où les valeurs isotopiques des minéraux dans les veines tardives sont approximativement 3 %o plus basses (avec des valeurs extrêmes négatifs), indiquant une contribution d'eau météorique aux fluides circulant dans les veines. Ces données suggèrent qu'une infiltration d'eau météorique a pu avoir lieu dans le bloque supérieur, où la fracturation des roches est plus intensive car le déplacement relatif le long de la faille y fut plus important, et la température maximale du métamorphisme plus basse. La troisième contribution traite de la géo-thermochronologie de la zone de contact entre la klippe de la Dent Blanche et la nappe de Tsaté. De petits zircons euhédraux ont été trouvés dans un plan de faille minéralisé (parallèle à la Faille du Rhône, voir première partie de l'étude), riche en hématite et quartz, de la zone d'étude. Les analyses U/Pb donnent des âges radiométriques autour de 270 - 280 Ma aux zircons extraits de la minéralisation ainsi que ceux extraits de la roche encaissante, ce qui correspond à l'âge de la nappe de la Dent Blanche et non celui de la nappe du Tsaté qui est elle-même classiquement interprétée comme une ophiolite Jurassique de l'Océan Liguro-Piémontais. Ces données suggèrent que les zircons contenus dans la veine ont été hérités de la roche encaissante. Les résultats (U-Th)/He indiquent un âge de refroidissement différent pour la roche encaissante (25.5 ± 2.0 Ma) que celui de la minéralisation (17.7 ±1.4 Ma). Le thermomètre isotopique quartz-hématite indique une température d'équilibre, et donc de mise en place de la minéralisation, d'environ 170 °C, température très proche de la température de -180 °C de fermeture du zircon pour le système (U-Th)/He. Ceci suggère que l'âge de refroidissement des zircons de la minéralisation correspond aussi à l'âge de formation de la faille.Thesis abstractFluid circulation in fractured rocks is a common process in geology, and it is generally the consequence of faulting and fracturing during both tectonic compression and extension. This thesis is focused on fluid circulation during late stages of the Alpine exhumation. After a structural analysis of the late brittle deformation of the studied samples, several analytical methods (stable isotope investigations, U/Pb radiometric dating, (U-Th)/He thermochronology) have been applied to understand the interaction of metamorphic and meteoric fluids with one another as well as with the host rock. This thesis is articulated around three study directions. All studies were conducted in the Penninic Zone of the Valais, Switzerland. The first study deals with late, brittle deformation and focuses on the different deformation styles and on the relative age of the different families of fractures. In order to do this, late brittle structures observed in four different domains have been subdivided as a function of the existence (or not) and type of mineralization. Comparisons between mineralized and non-mineralized strike directions for all four domains show that mineralized structures follow the strike orientation of major tectonic movements indicated in the Penninic Zone of the Valais (Aosta-Ranzola Line to the S, Rhône Line to the Ν and Simplon Fault Zone to the E), whereas non-mineralized fractures have a more variable strike orientation. This difference could be interpreted as indicative of tectonic-related faulting (mineralized structures) vs. local, collapse-related faulting (non-mineralized fractures), but it is not strong enough to indicate a relative age of the late brittle structures, and/or a change in the orientation of the strain field in post-Miocene times. The second studied area is focused on the Simplon Fault Zone (SFZ). Stable isotope analyses of minerals filling these late fractures indicate that there are two different fluid circulation systems in the footwall and hanging wall of the SFZ. In the footwall, δ180 values of quartz from both the host rock and the late veins range from +10 %o to +12 %o. This is consistent with buffering of circulating fluids by the host rock during fracturing and vein precipitation. In the hanging wall, δΙ80 values for quartz crystals from the host rock and the late veins are similar in both the northern and southern parts of the detachment that are both affected by the same degree of metamorphism (greenschist to the Ν and amphibolite to the S). This is not the case in the central part of the SFZ, where there is a jump from amphibolite facies in the footwall to greenschist facies in the hanging wall. δ,80 values for quartz from the hanging wall late veins are approximately 3.0 %o lower (down to negative values in some cases) than the values observed in the footwall These data suggest that infiltration of meteoric water may have occurred in the most fractured parts of the hanging wall, where relative displacement on the SFZ was the greatest and the peak temperature lower. In the less fractured footwall the δ180 values reflect a host rock-buffered system.The third study is focused on geo-thermochronology at the contact between the Dent Blanche nappe and the Tsaté nappe where small, euhedral zircons were found in a hematite- and quartz-rich mineralization on a late normal fault plane parallel to the Rhône Line (see first part of the study). U/Pb analysis indicates that the zircons - both in the late mineralization and in the host rock - have absolute radiometric ages clustering around 270 - 280 Ma, which is the accepted age for intrusive rocks from the Austroalpine Dent Blanche units but not for the Tsaté nappe. The latter is classically interpreted as an ophiolitic remnant of the Jurassic Liguro-Piemontais Ocean. U/Pb analyses suggest that zircons in late mineralization are all inherited from the host rock; however, results of (U-Th)/He analyses indicate that cooling ages for the host rocks are different to the cooling ages for the zircons in late mineralization. Indeed, the calculated cooling age for the Arolla gneiss is 25.5 ± 2.0 Ma, whilst the cooling age for the associated mineralized fault plane is 17.7 ±1.4 Ma. Oxygen stable isotope fractionation between quartz and hematite in the same late mineralization corresponds to temperatures of about 170 °C. The proximity of the calculated emplacement temperature for the mineralization and the lower accepted closure temperature for zircon in the (U-Th)/He system (-180 °C) imply that the age of 17.7 ± 1.4 Ma can also be interpreted as the formation age of this late brittle fault.Résumé grand publicLa circulation des fluides dans les roches fracturées est typique de nombreux processus géologiques, et très souvent est la conséquence de la fracturation des roches. Cette thèse aborde la question de la circulation des fluides pendant les dernières phases du soulèvement des Alpes. Après une analyse structurale de la fracturation directement sur le terrain, plusieurs méthodes géochimiques ont été appliquées pour comprendre l'interaction entre les différents fluides circulants, et avec leur propre roche mère. L'étude, concentrée sur trois directions principales, a été conduite dans la zone Pennique du Valais suisse. La première partie traite de la déformation cassante dans le secteur cité. L'analyse détaillée des fractures a permis de les subdiviser en structures minéralisées et non-minéralisées, sur quatre domaines différents. La comparaison entre les directions des structures minéralisées et non-minéralisées a permis de montrer que les premières suivent l'orientation des accidents tectoniques majeurs de la région, alors que les structures non- minéralisées ont une orientation plus variable. Cette différence pourrait être interprétée comme indication d'une dislocation tectonique (structures minéralisées) contre une dislocation gravitaire locale (structures non-minéralisées), mais elle n'est pas assez forte pour indiquer un âge relatif des structures tardives et/ou un changement de l'orientation des contraintes après -20 Ma vers le présent.A partir de ces observations, la deuxième étude est concentrée dans la région de la faille du Simplon. Les analyses géochimiques sur les minéraux remplissant les structures tardives indiquent qu'il y a deux différents systèmes de circulation des fluides dans les deux parties (toit et mur) de la faille. Dans le mur, les valeurs isotopiques des minéraux cristallisés à partir d'un fluide tardif sont les mêmes de ceux de la roche mère, donc il y a eu rééquilibration chimique entre fluide et roche pendant la fracturation de cette dernière et la précipitation des minéraux. Dans le toit, les valeurs isotopiques dans la roche mère et dans les minéraux des veines tardives sont comparables dans les parties Ν et S de la faille, où les roches du toit et du mur ont atteint une température maximale - pendant phase prograde de la formation des Alpes - comparable. Au contraire, dans la partie centrale, où le mur a atteint des températures maximales plus élevées par rapport au toit, les valeurs géochimiques des minéralisations tardives du toit sont parfois plus basses que les valeurs observées dans le mur. Ces données suggèrent que l'infiltration de l'eau de surface aurait pu se produire dans la partie plus fracturée du toit, où le déplacement relatif le long de la faille était majeur et les températures maximales mineures. Au contraire, les données géochimiques du mur de la partie centrale indiquent un système isotopique équilibré par la roche mère.La troisième partie de ce travail se base sur l'étude géochimique intégrée des isotopes stables d'Oxygène et radioactifs du Plomb, Uranium, Thorium et Hélium, auprès d'une faille normale minéralisée et des roches de la région à cheval entre deux nappes, la nappe de la Dent Blanche et la nappe de Tsaté. Ici, des petits zircons ont été trouvés dans la minéralisation citée, riche en hématite et quartz. L'analyse radiométrique Uranium/Plomb a montré que les zircons dans la minéralisation et dans les roches autour ont des âges comparables (autour 280 Ma). Cela signifie que les zircons dans la minéralisation tardive ont été hérités de la roche mère pendant la fracturation et la circulation des fluides tardives. De l'autre coté, les résultats des analyses Uranium-Thorium/Hélium indiquent que les âges de refroidissement pour les roches mères sont différents comparés aux âges de refroidissement pour les zircons dans la minéralisation tardive: ces derniers sont plus jeunes d'environ 8 Ma (autour 25 Ma et autour 17 Ma respectivement). Les analyses des isotopes de l'oxygène sur quartz et hématite dans la même minéralisation donnent une température de mise en place de cette dernière d'environ 170° C. La température de fermeture du système chimique des zircons dans le système (Uranium-Thorium)/Hélium est d'environ 180 °C: la proximité de ces deux températures implique que l'âge de refroidissement de la minéralisation tardive peut également être interprété comme âge de formation de la faille.