Microstructural Dependence of Work Hardening Behavior in Martensite-Ferrite Microalloyed Steels

Martensite-ferrite microstructures were produced in four microalloyed steels A (Fe-0.44C-Cr-V), B (Fe-0.26C-Cr-V), C (Fe-0.34C-Cr-Ti-V), and D (Fe-0.23C-Cr-V) by intercritical annealing. SEM analysis reveals that steels A and C contained higher martensite fraction and finer ferrite when compared to steels B and D which contained coarser ferrite grains and lower martensite fraction. A network of martensite phase surrounding the ferrite grains was found in all the steels. Crystallographic texture was very weak in these steels as indicated by EBSD analysis. The steels contained negligible volume fraction of retained austenite (approx. 3-6%). TEM analysis revealed the presence of twinned and lath martensite in these steels along with ferrite. Precipitates (carbides and nitrides) of Ti and V of various shapes with few nanometers size were found, particularly in the microstructures of steel B. Work hardening behavior of these steels at ambient temperature was evaluated through modified Jaoul-Crussard analysis, and it was characterized by two stages due to presence of martensite and ferrite phases in their microstructure. Steel A displayed large work hardening among other steel compositions. Work hardening behavior of the steels at a warm working temperature of 540 A degrees C was characterized by a single stage due to the decomposition of martensite into ferrite and carbides at this temperature as indicated by SEM images of the steels after warm deformation.

A trade-off between maxima in efficiency and specific work output of super- and trans-critical CO2 Brayton cycles

Several operational aspects for thermal power plants in general are non-intuitive and involve simultaneous optimization of a number of operational parameters. In the case of solar operated power plants, it is even more difficult due to varying heat source temperatures induced by variability in insolation levels. This paper introduces a quantitative methodology for load regulation of a CO2 based Brayton cycle power plant using the `thermal efficiency and specific work output' coordinate system. The analysis shows that a transcritical CO2 cycle offers more flexibility under part load performance than the supercritical cycle in case of non-solar power plants. However, for concentrated solar power, where efficiency is important, supercritical CO2 cycle fares better than transcritical CO2 cycle. A number of empirical equations relating heat source temperature, high side pressure with efficiency and specific work output are proposed which could assist in generating control algorithms. (C) 2015 Elsevier B.V. All rights reserved.

Non-Abelian gauge redundancy and entropic ambiguities

The von Neumann entropy of a generic quantum state is not unique unless the state can be uniquely decomposed as a sum of extremal or pure states. Therefore one reaches the remarkable possibility that there may be many entropies for a given state. We show that this happens if the GNS representation (of the algebra of observables in some quantum state) is reducible, and some representations in the decomposition occur with non-trivial degeneracy. This ambiguity in entropy, which can occur at zero temperature, can often be traced to a gauge symmetry emergent from the non-trivial topological character of the configuration space of the underlying system. We also establish the analogue of an H-theorem for this entropy by showing that its evolution is Markovian, determined by a stochastic matrix. After demonstrating this entropy ambiguity for the simple example of the algebra of 2 x 2 matrices, we argue that the degeneracies in the GNS representation can be interpreted as an emergent broken gauge symmetry, and play an important role in the analysis of emergent entropy due to non-Abelian anomalies. We work out the simplest situation with such non-Abelian symmetry, that of an ethylene molecule.

Modelling Proximity Effects in Transverse Magnetic Mode for Lightning Studies

Lightning strike to instrumented and communication towers can be a source of electromagnetic disturbance to the system connected. Long cables running on these towers can get significant induction to their sheath/core, which would then couple to the connected equipments. For a quantitative analysis of the situation, suitable theoretical analysis is necessary. Due to the dominance of the transverse magnetic mode during the fast rising portion of the stroke current, which is the period of significant induction, a full wave solution based on Maxwell's equations is necessary. Owing to the large geometric aspect ratio of tower lattice elements and for feasibility of a numerical solution, the thin-wire formulation for the electric field integral equation is generally adopted. However, the classical thin-wire formulation is not set for handling non-cylindrical conductors like tower lattice elements and the proximity of other conductors. The present work investigates further into a recently proposed method for handling such a situation and optimizes the numerical solution approach.

Interplay of vector-like top partner multiplets in a realistic mixing set-up

The ATLAS and CMS collaborations at the LHC have performed analyses on the existing data sets, studying the case of one vector-like fermion or multiplet coupling to the standard model Yukawa sector. In the near future, with more data available, these experimental collaborations will start to investigate more realistic cases. The presence of more than one extra vector-like multiplet is indeed a common situation in many extensions of the standard model. The interplay of these vector-like multiplet between precision electroweak bounds, flavour and collider phenomenology is a important question in view of establishing bounds or for the discovery of physics beyond the standard model. In this work we study the phenomenological consequences of the presence of two vector-like multiplets. We analyse the constraints on such scenarios from tree-level data and oblique corrections for the case of mixing to each of the SM generations. In the present work, we limit to scenarios with two top-like partners and no mixing in the down-sector.

A CAPABILITY APPROACH BASED STAKEHOLDER ANALYSIS FOR THE BASE OF THE PYRAMID: A CASE STUDY OF THE FIREWOOD BASED COOK-STOVES

People living under $2 income per day, referred as Base of the Pyramid (BoP), face undesired situations like lack of nutrition, health, education etc. Design as a process of changing current undesired situation to a desired situation has failed. A crucial reason behind these failures is lack of normative basis to identify and understand the absent or unsatisfied stakeholder. Currently stakeholder analysis in the design is heuristic. This paper uses a normative framework of Capability Approach (CA) for the stakeholder analysis. A brief discussion on stakeholder theory and analysis is used to identify gaps in the literature. The constructs of the CA are discussed for its suitability to the purpose. Along with methodological details, data generated from the stakeholder interviews, focus groups in a case study of dissemination of improved cook-stoves is used to interlink the theory with the practice. The scope of this work is in identifying and investigating the motives of the stakeholders in the involvement in the product. Though a lot of insights to discern and manage crucial stakeholders is inbuilt in the methodology, this work does not claim explicit coverage of these aspects.

Relationships between hardness, elastic modulus, and the work of indentation

The work done during indentation is examined using dimensional analysis and finite element calculations for conical indentation in elastic-plastic solids with work hardening. An approximate relationship between the ratio of hardness to elastic modulus and the ratio of irreversible work to total work in indentation is found. Consequently, the ratio of hardness to elastic modulus may be obtained directly from measuring the work of indentation. Together with a well-known relationship between elastic modulus, initial unloading slope, and contact area, a new method is then suggested for estimating the hardness and modulus of solids using instrumented indentation with conical or pyramidal indenters.

Scaling approach to conical indentation in elastic-plastic solids with work hardening

We derive, using dimensional analysis and finite element calculations, several scaling relationships for conical indentation in elastic-plastic solids with work hardening. Using these scaling relationships, we examine the relationships between hardness, contact area, initial unloading slope, and mechanical properties of solids. The scaling relationships also provide new insights into the shape of indentation curves and form the basis for understanding indentation measurements, including nano- and micro-indentation techniques. They may also be helpful as a guide to numerical and finite element calculations of indentation problems.

Essential and Non-Essential Work of Fracture of PI/SiO2 Hybrid Thin Films

Essential work of fracture (EWF) analysis is used to study the effect of the silica doping level on fracture toughness of polyimide/silica (PI/SiO2) hybrid films. By using double-edge-notched-tension (DENT) specimens with different ligament lengths, it seems that the introduction of silica additive can improve the specific essential work of fracture (w (e) ) of PI thin films, but the specific non-essential work of fracture (beta w (p) ) will decease significantly as the silica doping level increasing from 1 to 5 wt.%, and even lower than that of neat PI. The failure process of the fracture is investigated with online scanning electron microscope (SEM) observation and the parameters of non-essential work of fracture, beta and w (p) , are calculated based on finite element (FE) method.

Effect of Work of Adhesion on Nanoindentation

Three adhesion contact models, JKR (Johnson-Kendall-Roberts), DMT (Derjaguin-Muller-Toporov) and MD (Maugis-Dugdale) are compared with the Hertz model in dealing with the nano-contact problems. It has been shown that the dimensionless load parameter, $\bar{P}=P/(\pi\Delta\gamma R)$, and the transition parameter, $\Lambda$, have significant influences on the contact stiffness (contact area) at micro/nano-scale and should not be ignored in shallow nanoindentation.

Revelation of a Functional Dependence of the Sum of Two Uniaxial Strengths/Hardness on Elastic Work/Total Work of Indentation

Dimensional and finite element analyses were used to analyze the relationship between the mechanical properties and instrumented indentation response of materials. Results revealed the existence of a functional dependence of (engineering yield strength sigma(E,y) + engineering tensile strength sigma(E,b))/Oliver & Pharr hardness on the ratio of reversible elastic work to total work obtained from an indentation test. The relationship links up the Oliver & Pharr hardness with the material strengths, although the Oliver & Pharr hardness may deviate from the true hardness when sinking in or piling up occurs. The functional relationship can further be used to estimate the SUM sigma(E,y) + sigma(E,b) according to the data of an instrumented indentation test. The sigma(E,y) + sigma(E,b) value better reflects the strength of a material compared to the hardness value alone. The method was shown to be effective when applied to aluminum alloys. The relationship can further be used to estimate the fatigue limits, which are usually obtained from macroscopic fatigue tests in different modes.

Style and the “Idea” of the sophist after Plato : the impact of form typology on sophistic teaching and writing on interdisciplinary scholarly work

Resumen: Después de la primera sofística, los sofistas actuaron entre el resto de los pensadores del Mediterráneo como un grupo definido. Dado que hay muchos ejemplos que muestran que los sofistas ejercían sus prácticas y que también eran personas comprometidas en otras actividades, vamos a examinar aquí diversos casos de semejanzas y diferencias entre ellos y otros grupos de pensadores. Nuestras tres preguntas fundamentales son: qué, cómo y por qué los sofistas escribían y enseñaban. Intentaremos responder haciendo un análisis diacrónico de las principales formas y géneros de escritura que produjeron (qué). El cómo lo responderemos en su desenvolvimiento como una actividad comunicativa más allá de las fronteras de las disciplinas de la época. El por qué tendrá su respuesta al enfatizar la necesidad de la actividad de los sofistas en la socialización de la época y en la educación de la antigüedad. Al aseverar que el estilo era la idea de los sofistas, ponemos la noción de idea en Platón en el contexto de idea derivado de los sofistas contemporáneos a él y de los sofistas posteriores (segunda sofística) y centramos el foco en la función de visualidad expresada en su concepto de idea desde las obras sofísticas más tempranas en la época de Platón hasta las contribuciones posteriores.

La evolución reciente de la inversión en Argentina

Resumen: En este trabajo se hace una comparación entre las inversiones que se han llevado a cabo en dos períodos bien marcados en Argentina, a saber, pre crisis y post crisis. El período pre crisis donde la inversión era financiada por el sector externo, se caracteriza por un fuerte crecimiento de la inversión debido al sostenido ingreso de capitales, esto provoca que el país sea muy vulnerable ante cambios adversos en la situación macroeconómica internacional. Opuesto a la etapa anterior, en el período post crisis, la inversión es financiada exclusivamente con reinversión de utilidades y con ahorro interno. Se quiere mostrar con esto que el crecimiento no es sostenible si solo se asienta en el consumo, el rol de la inversión es fundamental tanto en la sustentabilidad de la tasa de crecimiento como en la dinámica de los precios. Ignorar su importancia condena a la sociedad a la pobreza.

Sistema nacional de procuración de órganos y tejidos para trasplante

El sistema nacional de procuración de órganos, tejidos y células para trasplante en la Argentina es impulsado, normatizado, coordinado y fiscalizado por el Incucai (Instituto Nacional Central Único Coordinador de Ablación e Implante). Hoy, el sistema de salud cuenta con más de 4000 profesionales capacitados, 300 centros de trasplante, 50 bancos de tejidos y 30 laboratorios de histocompatibilidad habilitados por el Incucai en todo el país. La conciencia sobre la importancia de la donación ha crecido y actualmente cerca de 2.300.000 personas han manifestado la decisión de donar sus órganos y tejidos y otras 40.000 se han inscripto como donantes de células de la médula ósea. En el presente trabajo se analizarán los siguientes puntos: situación actual, logros y avances; principios de definen la distribución de órganos; retos de la donación y el trasplante en la Argentina.