Low-frequency transcranial magnetic stimulation over left dorsal premotor cortex improves the dynamic control of visuospatially cued actions.

Left rostral dorsal premotor cortex (rPMd) and supramarginal gyrus (SMG) have been implicated in the dynamic control of actions. In 12 right-handed healthy individuals, we applied 30 min of low-frequency (1 Hz) repetitive transcranial magnetic stimulation (rTMS) over left rPMd to investigate the involvement of left rPMd and SMG in the rapid adjustment of actions guided by visuospatial cues. After rTMS, subjects underwent functional magnetic resonance imaging while making spatially congruent button presses with the right or left index finger in response to a left- or right-sided target. Subjects were asked to covertly prepare motor responses as indicated by a directional cue presented 1 s before the target. On 20% of trials, the cue was invalid, requiring subjects to readjust their motor plan according to the target location. Compared with sham rTMS, real rTMS increased the number of correct responses in invalidly cued trials. After real rTMS, task-related activity of the stimulated left rPMd showed increased task-related coupling with activity in ipsilateral SMG and the adjacent anterior intraparietal area (AIP). Individuals who showed a stronger increase in left-hemispheric premotor-parietal connectivity also made fewer errors on invalidly cued trials after rTMS. The results suggest that rTMS over left rPMd improved the ability to dynamically adjust visuospatial response mapping by strengthening left-hemispheric connectivity between rPMd and the SMG-AIP region. These results support the notion that left rPMd and SMG-AIP contribute toward dynamic control of actions and demonstrate that low-frequency rTMS can enhance functional coupling between task-relevant brain regions and improve some aspects of motor performance.

Development of fluid conduits in the auriferous shear zones of the Hutti Gold Mine, India: evidence for spatially and temporally heterogeneous fluid flow

The gold mineralization of the Hutti Mine is hosted by nine parallel, N - S trending, steeply dipping, 2 - 10 m wide shear zones, that transect Archaean amphibolites. The shear zones were formed after peak metamorphism during retrograde ductile D, shearing in the lower amphibolite facies. They were reactivated in the lower to mid greenschist facies by brittle-ductile D-3 shearing and intense quartz veining. The development of a S-2-S-3 crenulation cleavage facilitates the discrimination between the two deformation events and contemporaneous alteration and gold mineralization. Ductile D, shearing is associated with a pervasively developed distal chlorite - sed cite alteration assemblage in the outer parts of the shear zones and the proximal biotite-plagioclase alteration in the center of the shear zones. D3 is characterized by development of the inner chlorite-K-feldspar alteration, which forms a centimeter-scale alteration halo surrounding the laminated quartz veins and replaces earlier biotite along S-3. The average size of the laminated vein systems is 30-50 m along strike as well as down-dip and 2-6 m in width. Mass balance calculations suggest strong metasomatic changes for the proximal biotite-plagioclase alteration yielding mass and volume increase of ca. 16% and 12%, respectively. The calculated mass and volume changes of the distal chlorite-sericite alteration (ca. 11%, ca. 8%) are lower. The decrease in 6180 values of the whole rock from around 7.5 parts per thousand for the host rocks to 6-7 parts per thousand for the distal chlorite-sericite and the proximal biotite-plagioclase alteration and around 5 parts per thousand for the inner chlorite-K-feldspar alteration suggests hydrothermal alteration during two-stage deformation and fluid flow. The ductile D-2 deformation in the lower amphibolite facies has provided grain scale porosities by microfracturing. The pervasive, steady-state fluid flow resulted in a disseminated style of gold-sulfide mineralization and a penetrative alteration of the host rocks. Alternating ductile and brittle D3 deformation during lower to mid greenschist facies conditions followed the fault-valve process. Ductile creep in the shear zones resulted in a low permeability environment leading to fluid pressure build-up. Strongly episodic fluid advection and mass transfer was controlled by repeated seismic fracturing during the formation of laminated quartz(-gold) veins. The limitation of quartz veins to the extent of earlier shear zones indicate the importance of preexisting anisotropies for fault-valve action and economic gold mineralization. (C) 2003 Elsevier B.V. All rights reserved.

Analyzing dynamic intellectual capital: System-based theory and application

This research report presents an application of systems theory to evaluating intellectual capital (IC) as organization's ability for self-renewal. As renewal ability is a dynamic capability of an organization as a whole, rather than a static asset or an atomistic competence of separate individuals within the organization, it needs to be understood systemically. Consequently, renewal ability has to be measured with systemic methods that are based on a thorough conceptual analysis of systemic characteristics of organizations. The aim of this report is to demonstrate the theory and analysis methodology for grasping companies' systemic efficiency and renewal ability. The volume is divided into three parts. The first deals with the theory of organizations as self-renewing systems. In the second part, the principles of quantitative analysis of organizations are laid down. Finally, the detailed mathematics of the renewal indices are presented. We also assert that the indices produced by the analysis are an effective tool for the management and valuation of knowledge-intensive companies.

Le pergélisol dans les terrains sédimentaires à forte déclivité: distribution, régime thermique et instabilités

Résumé: Dans le contexte d'un climat de plus en plus chaud, la localisation du pergélisol dans les terrains sédimentaires à forte déclivité et l'évaluation des mouvements de terrain qui y ont cours s'avèrent primordiales. S'insérant dans cette problématique, ce travail de thèse s'articule autour de deux axes de recherche différents. D'un point de vue statique, cette recherche propose une étude de la distribution et des caractéristiques du pergélisol dans les éboulis de la zone périglaciaire alpine. D'un point de vue dynamique, une analyse de l'influence des caractéristiques du pergélisol (teneur en glace, température du pergélisol, etc.) et des variations des températures de l'air et du sol sur les vitesses de fluage des corps sédimentaires gelés est effectuée. Afin de répondre à ce double objectif, l'approche "terrain" a été privilégiée. Pour déterminer la répartition et les caractéristiques du pergélisol, les méthodes traditionnelles de prospection du pergélisol ont été utilisées, à savoir la mesure de la température du sol à la base du manteau neigeux (BTS), la mesure de la température du sol en continu ainsi que la méthode géoélectrique. Les mouvements de terrain ont pour leur part été mesurés à l'aide d'un GPS différentiel. L'étude de la distribution du pergélisol a été effectuée dans une quinzaine d'éboulis situés dans les régions du Mont Gelé (Verbier-Nendaz) et d'Arolla principalement. Dans la plupart des cas, un pergélisol a pu être mis en évidence dans la partie inférieure des accumulations sédimentaires, alors que la partie médiane des éboulis n'est, le plus souvent, pas gelée. Si cette absence de pergélisol se prolonge parfois dans les portions sommitales des pentes, les mesures réalisées montrent que dans d'autres cas des sédiments gelés y sont à nouveau présents. Les résistivités électriques mesurées dans les portions gelées des éboulis étudiés sont dans la plupart des cas nettement inférieures à celles mesurées sur les glaciers rocheux. Des études préalables ont montré que des circulations d'air internes sont responsables de l'anomalie thermique négative et, lorsqu'il existe, du pergélisol que l'on trouve dans la partie inférieure d'éboulis situés plus de 1000 m plus bas que la limite inférieure régionale du pergélisol discontinu. L'étude de quatre sites de basse altitude (1400-1900 m), et notamment l'équipement du site de Dreveneuse (Préalpes Valaisannes) avec deux forages, des capteurs de température de surface et un anémomètre a permis de vérifier et de préciser le mécanisme de ventilation actif au sein des éboulis froids de basse altitude. Ce mécanisme fonctionne de la manière suivante: en hiver, l'air contenu dans l'éboulis, plus chaud et plus léger que l'air extérieur, monte à l'intérieur de l'accumulation sédimentaire et est expulsé dans ses parties sommitales. Cet effet de cheminée provoque une aspiration d'air froid à l'intérieur de la partie inférieure de l'éboulis, causant ainsi un sur-refroidissement marqué du terrain. En été, le mécanisme s'inverse, l'éboulis étant plus froid que l'air environnant. De l'air froid est alors expulsé au bas de la pente. Une ventilation ascendante hivernale a pu être mise en évidence dans certains des éboulis de haute altitude étudiés. Elle est probablement en grande partie responsable de la configuration particulière des zones gelées observées. Même si l'existence d'un effet de cheminée n'a pu être démontrée dans tous les cas, du fait notamment de la glace interstitielle qui entrave le cheminement de l'air, des indices laissant présager son possible fonctionnement existent dans la quasi totalité des éboulis étudiés. L'absence de pergélisol à des altitudes qui lui sont favorables pourrait en tous les cas s'expliquer par un réchauffement du terrain lié à des expulsions d'air relativement chaud. L'étude des mouvements de terrain a été effectuée sur une dizaine de sites, principalement sur des glaciers rocheux, mais également sur une moraine de poussée et - II - Résumé ? abstract quelques éboulis. Plusieurs glaciers rocheux présentent des formes de déstabilisation récente (niches d'arrachement, blocs basculés, apparition de la matrice fine à la surface, etc.), ce qui témoigne d'une récente accélération des vitesses de déplacement. Ce phénomène, qui semble général à l'échelle alpine, est probablement à mettre sur le compte du réchauffement du pergélisol depuis une vingtaine d'années. Les vitesses mesurées sur ces formations sont souvent plus élevées que les valeurs habituellement proposées dans la littérature. On note par ailleurs une forte variabilité inter-annuelle des vitesses, qui semblent dépendre de la variation de la température moyenne annuelle de surface. Abstract: In the context of a warmer climate, the localisation of permafrost in steep sedimentary terrain and the measurement of terrain movements that occur in these areas is of great importance. With respect to these problems, this PhD thesis follows two different research axes. From a static point of view, the research presents a study of the permafrost distribution and characteristics in the talus slopes of the alpine periglacial belt. From a dynamic point of view, an analysis of the influence of the permafrost characteristics (ice content, permafrost temperature, etc.) and air and soil temperature variations on the creep velocities of frozen sedimentary bodies is carried out. In order to attain this double objective, the "field" approach was favoured. To determine the distribution and the characteristics of permafrost, the traditional methods of permafrost prospecting were used, i.e. ground surface temperature measurements at the base of the snow cover (BTS), year-round ground temperature measurements and DC-resistivity prospecting. The terrain movements were measured using a differential GPS. The permafrost distribution study was carried out on 15 talus slopes located mainly in the Mont Gelé (Verbier-Nendaz) and Arolla areas (Swiss Alps). In most cases, permafrost was found in the lower part of the talus slope, whereas the medium part was free of ice. In some cases, the upper part of the talus is also free of permafrost, whereas in other cases permafrost is present. Electrical resistivities measured in the frozen parts of the studied talus are in most cases clearly lower than those measured on rock glaciers. Former studies have shown that internal air circulation is responsible for the negative thermal anomaly and, when it exists, the permafrost present in the lower part of talus slopes located more than 1000 m below the regional lower limit of discontinuous permafrost. The study of four low-altitude talus slopes (1400-1900 m), and notably the equipment of Dreveneuse field site (Valais Prealps) with two boreholes, surface temperature sensors and an anemometer permitted to verify and to detail the ventilation mechanism active in low altitude talus slopes. This mechanism works in the following way: in winter, the air contained in the block accumulation is warmer and lighter than the surrounding air and therefore moves upward in the talus and is expelled in its upper part. This chimney effect induces an aspiration of cold air in the interior of the lower part of talus, that causes a strong overcooling of the ground. In summer, the mechanism is reversed because the talus slope is colder than the surrounding air. Cold air is then expelled in the lower part of the slope. Evidence of ascending ventilation in wintertime could also be found in some of the studied high-altitude talus slopes. It is probably mainly responsible for the particular configuration of the observed frozen areas. Even if the existence of a chimney effect could not be demonstrated in all cases, notably because of interstitial ice that obstructs Résumé ? abstract - III - the air circulation, indices of its presence exist in nearly all the studied talus. The absence of permafrost at altitudes favourable to its presence could be explained, for example, by the terrain warming caused by expulsion of relatively warm air. Terrain movements were measured at about ten sites, mainly on rock glaciers, but also on a push moraine and some talus slopes. Field observations reveal that many rock glaciers display recent destabilization features (landslide scars, tilted blocks, presence of fine grained sediments at the surface, etc.) that indicate a probable recent acceleration of the creep velocities. This phenomenon, which seems to be widespread at the alpine scale, is probably linked to the permafrost warming during the last decades. The measured velocities are often higher than values usually proposed in the literature. In addition, strong inter-annual variations of the velocities were observed, which seems to depend on the mean annual ground temperature variations.

Three essays in dynamic corporate finance

The three essays constituting this thesis focus on financing and cash management policy. The first essay aims to shed light on why firms issue debt so conservatively. In particular, it examines the effects of shareholder and creditor protection on capital structure choices. It starts by building a contingent claims model where financing policy results from a trade-off between tax benefits, contracting costs and agency costs. In this setup, controlling shareholders can divert part of the firms' cash ows as private benefits at the expense of minority share- holders. In addition, shareholders as a class can behave strategically at the time of default leading to deviations from the absolute priority rule. The analysis demonstrates that investor protection is a first order determinant of firms' financing choices and that conflicts of interests between firm claimholders may help explain the level and cross-sectional variation of observed leverage ratios. The second essay focuses on the practical relevance of agency conflicts. De- spite the theoretical development of the literature on agency conflicts and firm policy choices, the magnitude of manager-shareholder conflicts is still an open question. This essay proposes a methodology for quantifying these agency conflicts. To do so, it examines the impact of managerial entrenchment on corporate financing decisions. It builds a dynamic contingent claims model in which managers do not act in the best interest of shareholders, but rather pursue private benefits at the expense of shareholders. Managers have discretion over financing and dividend policies. However, shareholders can remove the manager at a cost. The analysis demonstrates that entrenched managers restructure less frequently and issue less debt than optimal for shareholders. I take the model to the data and use observed financing choices to provide firm-specific estimates of the degree of managerial entrenchment. Using structural econometrics, I find costs of control challenges of 2-7% on average (.8-5% at median). The estimates of the agency costs vary with variables that one expects to determine managerial incentives. In addition, these costs are sufficient to resolve the low- and zero-leverage puzzles and explain the time series of observed leverage ratios. Finally, the analysis shows that governance mechanisms significantly affect the value of control and firms' financing decisions. The third essay is concerned with the documented time trend in corporate cash holdings by Bates, Kahle and Stulz (BKS,2003). BKS find that firms' cash holdings double from 10% to 20% over the 1980 to 2005 period. This essay provides an explanation of this phenomenon by examining the effects of product market competition on firms' cash holdings in the presence of financial constraints. It develops a real options model in which cash holdings may be used to cover unexpected operating losses and avoid inefficient closure. The model generates new predictions relating cash holdings to firm and industry characteristics such as the intensity of competition, cash flow volatility, or financing constraints. The empirical examination of the model shows strong support of model's predictions. In addition, it shows that the time trend in cash holdings documented by BKS can be at least partly attributed to a competition effect.

Direct-on-line axial flux permanent magnet synchronous generator static and dynamic performance

In distributed energy production, permanent magnet synchronous generators (PMSG) are often connected to the grid via frequency converters, such as voltage source line converters. The price of the converter may constitute a large part of the costs of a generating set. Some of the permanent magnet synchronous generators with converters and traditional separately excited synchronous generators couldbe replaced by direct-on-line (DOL) non-controlled PMSGs. Small directly networkconnected generators are likely to have large markets in the area of distributed electric energy generation. Typical prime movers could be windmills, watermills and internal combustion engines. DOL PMSGs could also be applied in island networks, such as ships and oil platforms. Also various back-up power generating systems could be carried out with DOL PMSGs. The benefits would be a lower priceof the generating set and the robustness and easy use of the system. The performance of DOL PMSGs is analyzed. The electricity distribution companies have regulations that constrain the design of the generators being connected to the grid. The general guidelines and recommendations are applied in the analysis. By analyzing the results produced by the simulation model for the permanent magnet machine, the guidelines for efficient damper winding parameters for DOL PMSGs are presented. The simulation model is used to simulate grid connections and load transients. The damper winding parameters are calculated by the finite element method (FEM) and determined from experimental measurements. Three-dimensional finite element analysis (3D FEA) is carried out. The results from the simulation model and 3D FEA are compared with practical measurements from two prototype axial flux permanent magnet generators provided with damper windings. The dimensioning of the damper winding parameters is case specific. The damper winding should be dimensioned based on the moment of inertia of the generating set. It is shown that the damper winding has optimal values to reach synchronous operation in the shortest period of time after transient operation. With optimal dimensioning, interferenceon the grid is minimized.

Improving Dynamic Characteristics of Open-loop Controlled Log Crane

The improvement of the dynamics of flexible manipulators like log cranes often requires advanced control methods. This thesis discusses the vibration problems in the cranes used in commercial forestry machines. Two control methods, adaptive filtering and semi-active damping, are presented. The adaptive filter uses a part of the lowest natural frequency of the crane as a filtering frequency. The payload estimation algorithm, filtering of control signal and algorithm for calculation of the lowest natural frequency of the crane are presented. The semi-active damping method is basedon pressure feedback. The pressure vibration, scaled with suitable gain, is added to the control signal of the valve of the lift cylinder to suppress vibrations. The adaptive filter cuts off high frequency impulses coming from the operatorand semi-active damping suppresses the crane?s oscillation, which is often caused by some external disturbance. In field tests performed on the crane, a correctly tuned (25 % tuning) adaptive filter reduced pressure vibration by 14-17 % and semi-active damping correspondingly by 21-43%. Applying of these methods require auxiliary transducers, installed in specific points in the crane, and electronically controlled directional control valves.

Dynamic Model of a Small Once-Through Boiler

In this study, a model for the unsteady dynamic behaviour of a once-through counter flow boiler that uses an organic working fluid is presented. The boiler is a compact waste-heat boiler without a furnace and it has a preheater, a vaporiser and a superheater. The relative lengths of the boiler parts vary with the operating conditions since they are all parts of a single tube. The present research is a part of a study on the unsteady dynamics of an organic Rankine cycle power plant and it will be a part of a dynamic process model. The boiler model is presented using a selected example case that uses toluene as the process fluid and flue gas from natural gas combustion as the heat source. The dynamic behaviour of the boiler means transition from the steady initial state towards another steady state that corresponds to the changed process conditions. The solution method chosen was to find such a pressure of the process fluid that the mass of the process fluid in the boiler equals the mass calculated using the mass flows into and out of the boiler during a time step, using the finite difference method. A special method of fast calculation of the thermal properties has been used, because most of the calculation time is spent in calculating the fluid properties. The boiler was divided into elements. The values of the thermodynamic properties and mass flows were calculated in the nodes that connect the elements. Dynamic behaviour was limited to the process fluid and tube wall, and the heat source was regarded as to be steady. The elements that connect the preheater to thevaporiser and the vaporiser to the superheater were treated in a special way that takes into account a flexible change from one part to the other. The model consists of the calculation of the steady state initial distribution of the variables in the nodes, and the calculation of these nodal values in a dynamic state. The initial state of the boiler was received from a steady process model that isnot a part of the boiler model. The known boundary values that may vary during the dynamic calculation were the inlet temperature and mass flow rates of both the heat source and the process fluid. A brief examination of the oscillation around a steady state, the so-called Ledinegg instability, was done. This examination showed that the pressure drop in the boiler is a third degree polynomial of the mass flow rate, and the stability criterion is a second degree polynomial of the enthalpy change in the preheater. The numerical examination showed that oscillations did not exist in the example case. The dynamic boiler model was analysed for linear and step changes of the entering fluid temperatures and flow rates.The problem for verifying the correctness of the achieved results was that there was no possibility o compare them with measurements. This is why the only way was to determine whether the obtained results were intuitively reasonable and the results changed logically when the boundary conditions were changed. The numerical stability was checked in a test run in which there was no change in input values. The differences compared with the initial values were so small that the effects of numerical oscillations were negligible. The heat source side tests showed that the model gives results that are logical in the directions of the changes, and the order of magnitude of the timescale of changes is also as expected. The results of the tests on the process fluid side showed that the model gives reasonable results both on the temperature changes that cause small alterations in the process state and on mass flow rate changes causing very great alterations. The test runs showed that the dynamic model has no problems in calculating cases in which temperature of the entering heat source suddenly goes below that of the tube wall or the process fluid.

Dynamic Capabilities and Firm Performance

Firms operating in a changing environment have a need for structures and practices that provide flexibility and enable rapid response to changes. Given the challenges they face in attempts to keep up with market needs, they have to continuously improve their processes and products, and develop new products to match market requirements. Success in changing markets depends on the firm's ability to convert knowledge into innovations, and consequently their internal structures and capabilities have an important role in innovation activities. According 10 the dynamic capability view of the firm, firms thus need dynamic capabilities in (he form ofassets, processes and structures that enable strategic flexibility and support entrepreneurial opportunity sensing and exploitation. Dynamic capabilities are also needed in conditions of rapid change in the operating environment, and in activities such as new product development and expansion to new markets. Despite the growing interest in these issues and the theoretical developments in the field of strategy research, there are still only very few empirical studies, and large-scale empirical studies in particular, that provide evidence that firms'dynamic capabilities are reflected in performance differences. This thesis represents an attempt to advance the research by providing empirical evidence of thelinkages between the firm's dynamic capabilities and performance in intenationalization and innovation activities. The aim is thus to increase knowledge and enhance understanding of the organizational factors that explain interfirm performance differences. The study is in two parts. The first part is the introduction and the second part comprises five research publications covering the theoretical foundations of the dynamic capability view and subsequent empirical analyses. Quantitative research methodology is used throughout. The thesis contributes to the literature in several ways. While a lot of prior research on dynamic capabilities is conceptual in nature, or conducted through case studies, this thesis introduces empirical measures for assessing the different aspects, and uses large-scale sampling to investigate the relationships between them and performance indicators. The dynamic capability view is further developed by integrating theoretical frameworks and research traditions from several disciplines. The results of the study provide support for the basic tenets of the dynamic capability view. The empirical findings demonstrate that the firm's ability to renew its knowledge base and other intangible assets, its proactive, entrepreneurial behavior, and the structures and practices that support operational flexibility arepositively related to performance indicators.

Modeling dynamic behavior in tilting pad gas journal bearings

Thisresearch deals with the dynamic modeling of gas lubricated tilting pad journal bearings provided with spring supported pads, including experimental verification of the computation. On the basis of a mathematical model of a film bearing, a computer program has been developed, which can be used for the simulation of a special type of tilting pad gas journal bearing supported by a rotary spring under different loading conditions time dependently (transient running conditions due to geometry variations in time externally imposed). On the basis of literature, different transformations have been used in the model to achieve simpler calculation. The numerical simulation is used to solve a non-stationary case of a gasfilm. The simulation results were compared with literature results in a stationary case (steady running conditions) and they were found to be equal. In addition to this, comparisons were made with a number of stationary and non-stationary bearing tests, which were performed at Lappeenranta University of Technology using bearings designed with the simulation program. A study was also made using numerical simulation and literature to establish the influence of the different bearing parameters on the stability of the bearing. Comparison work was done with literature on tilting pad gas bearings. This bearing type is rarely used. One literature reference has studied the same bearing type as that used in LUT. A new design of tilting pad gas bearing is introduced. It is based on a stainless steel body and electron beam welding of the bearing parts. It has good operation characteristics and is easier to tune and faster to manufacture than traditional constructions. It is also suitable for large serial production.

Spray coating technique asa surface treatment for woodcontaining paper grades

The objective of this work was to introduce the emerging non-contacting spray coating process and compare it to the existing coating techniques. Particular emphasis was given to the details of the spraying process of paper coating colour and the base paper requirements set by the new coating method. Spraying technology itself is nothing new, but the atomisation process of paper coating colour is quite unknown to the paper industry. The differences between the rheology of painting and coating colours make it very difficult to utilise the existing information from spray painting research. Based on the trials, some basic conclusion can be made:The results of this study suggest that the Brookfield viscosity of spray coating colour should be as low as possible, presently a 50 mPas level is regarded as an optimum. For the paper quality and coater runnability, the solids level should be as high as possible. However, the graininess of coated paper surface and the nozzle wear limits the maximum solids level to 60 % at the moment. Most likelydue to the low solids and low viscosity of the coating colour the low shear Brookfield viscosity correlates very well with the paper and spray fan qualities. High shear viscosity is also important, but yet less significant than the low shear viscosity. Droplet size should be minimized and besides keeping the brrokfield viscosity low that can be helped by using a surfactant or dispersing agent in the coating colour formula. Increasing the spraying pressure in the nozzle can also reduce the droplet size. The small droplet size also improves the coating coverage, since there is hardly any levelling taking place after the impact with the base paper. Because of the lack of shear forces after the application, the pigment particles do not orientate along the paper surface. Therefore the study indicates that based on the present know-how, no quality improvements can be obtained by the use of platy type of pigments. The other disadvantage of them is the rapid deterioration of the nozzle lifetime. Further research in both coating colour rheology and nozzle design may change this in the future, but so far only round shape pigments, like typically calcium carbonate is, can be used with spray coating. The low water retention characteristics of spray coating, enhanced by the low solids and low viscosity, challenge the base paper absorption properties.Filler level has to be low not to increase the number of small pores, which have a great influence on the absorption properties of the base paper. Hydrophobic sizing reduces this absorption and prevents binder migration efficiently. High surface roughness and especially poor formation of the base paper deteriorate thespray coated paper properties. However, pre-calendering of the base paper does not contribute anything to the finished paper quality, at least at the coating colour solids level below 60 %. When targeting a standard offset LWC grade, spraycoating produces similar quality to film coating, but yet blade coating being on a slightly better level. However, because of the savings in both investment and production costs, spray coating may have an excellent future ahead. The porousnature of the spray coated surface offers an optimum substrate for the coldset printing industry to utilise the potential of high quality papers in their business.

Mass transfer and particleinteractions in granular systems and suspension flows

The purpose of this study was to investigate some important features of granular flows and suspension flows by computational simulation methods. Granular materials have been considered as an independent state ofmatter because of their complex behaviors. They sometimes behave like a solid, sometimes like a fluid, and sometimes can contain both phases in equilibrium. The computer simulation of dense shear granular flows of monodisperse, spherical particles shows that the collisional model of contacts yields the coexistence of solid and fluid phases while the frictional model represents a uniform flow of fluid phase. However, a comparison between the stress signals from the simulations and experiments revealed that the collisional model would result a proper match with the experimental evidences. Although the effect of gravity is found to beimportant in sedimentation of solid part, the stick-slip behavior associated with the collisional model looks more similar to that of experiments. The mathematical formulations based on the kinetic theory have been derived for the moderatesolid volume fractions with the assumption of the homogeneity of flow. In orderto make some simulations which can provide such an ideal flow, the simulation of unbounded granular shear flows was performed. Therefore, the homogeneous flow properties could be achieved in the moderate solid volume fractions. A new algorithm, namely the nonequilibrium approach was introduced to show the features of self-diffusion in the granular flows. Using this algorithm a one way flow can beextracted from the entire flow, which not only provides a straightforward calculation of self-diffusion coefficient but also can qualitatively determine the deviation of self-diffusion from the linear law at some regions nearby the wall inbounded flows. Anyhow, the average lateral self-diffusion coefficient, which was calculated by the aforementioned method, showed a desirable agreement with thepredictions of kinetic theory formulation. In the continuation of computer simulation of shear granular flows, some numerical and theoretical investigations were carried out on mass transfer and particle interactions in particulate flows. In this context, the boundary element method and its combination with the spectral method using the special capabilities of wavelets have been introduced as theefficient numerical methods to solve the governing equations of mass transfer in particulate flows. A theoretical formulation of fluid dispersivity in suspension flows revealed that the fluid dispersivity depends upon the fluid properties and particle parameters as well as the fluid-particle and particle-particle interactions.

Dynamic model of the left ventricle for use in simulation of myocardial perfusion SPECT and gated SPECT

Simulation is a useful tool in cardiac SPECT to assess quantification algorithms. However, simple equation-based models are limited in their ability to simulate realistic heart motion and perfusion. We present a numerical dynamic model of the left ventricle, which allows us to simulate normal and anomalous cardiac cycles, as well as perfusion defects. Bicubic splines were fitted to a number of control points to represent endocardial and epicardial surfaces of the left ventricle. A transformation from each point on the surface to a template of activity was made to represent the myocardial perfusion. Geometry-based and patient-based simulations were performed to illustrate this model. Geometry-based simulations modeled ~1! a normal patient, ~2! a well-perfused patient with abnormal regional function, ~3! an ischaemic patient with abnormal regional function, and ~4! a patient study including tracer kinetics. Patient-based simulation consisted of a left ventricle including a realistic shape and motion obtained from a magnetic resonance study. We conclude that this model has the potential to study the influence of several physical parameters and the left ventricle contraction in myocardial perfusion SPECT and gated-SPECT studies.