Horizontal Slug Flow in a Large-Size Pipeline: Experimentation and Modeling

The knowledge of the slug flow characteristics is very important when designing pipelines and process equipment. When the intermittences typical in slug flow occurs, the fluctuations of the flow variables bring additional concern to the designer. Focusing on this subject the present work discloses the experimental data on slug flow characteristics occurring in a large-size, large-scale facility. The results were compared with data provided by mechanistic slug flow models in order to verify their reliability when modelling actual flow conditions. Experiments were done with natural gas and oil or water as the liquid phase. To compute the frequency and velocity of the slug cell and to calculate the length of the elongated bubble and liquid slug one used two pressure transducers measuring the pressure drop across the pipe diameter at different axial locations. A third pressure transducer measured the pressure drop between two axial location 200 m apart. The experimental data were compared with results of Camargo's1 algorithm (1991, 1993), which uses the basics of Dukler & Hubbard's (1975) slug flow model, and those calculated by the transient two-phase flow simulator OLGA.

Pressure Drop in Vertical Core-Annular Flow

An experimental apparatus for the study of core annular flows of heavy oil and water at room temperature has been set up and tested at laboratory scale. The test section consists of a 2.75 cm ID galvanized steel pipe. Tap water and a heavy oil (17.6 Pa.s; 963 kg/m³) were used. Pressure drop in a vertical upward test section was accurately measured for oil flow rates in the range 0.297 - 1.045 l/s and water flow rates ranging from 0.063 to 0.315 l/s. The oil-water input ratio was in the range 1-14. The measured pressure drop comprises gravitational and frictional parts. The gravitational pressure drop was expressed in terms of the volumetric fraction of the core, which was determined from a correlation developed by Bannwart (1998b). The existence of an optimum water-oil input ratio for each oil flow rate was observed in the range 0.07 - 0.5. The frictional pressure drop was modeled to account for both hydrodynamic and net buoyancy effects on the core. The model was adjusted to fit our data and shows excellent agreement with data from another source (Bai, 1995).

Detection of Horizontal Two-Phase Flow Patterns Through a Neural Network Model

One of the main problems related to the transport and manipulation of multiphase fluids concerns the existence of characteristic flow patterns and its strong influence on important operation parameters. A good example of this occurs in gas-liquid chemical reactors in which maximum efficiencies can be achieved by maintaining a finely dispersed bubbly flow to maximize the total interfacial area. Thus, the ability to automatically detect flow patterns is of crucial importance, especially for the adequate operation of multiphase systems. This work describes the application of a neural model to process the signals delivered by a direct imaging probe to produce a diagnostic of the corresponding flow pattern. The neural model is constituted of six independent neural modules, each of which trained to detect one of the main horizontal flow patterns, and a last winner-take-all layer responsible for resolving when two or more patterns are simultaneously detected. Experimental signals representing different bubbly, intermittent, annular and stratified flow patterns were used to validate the neural model.

Three-dimensional supersonic flow over a spike-nosed body of revolution

The unsteady, viscous, supersonic flow over a spike-nosed body of revolution is numerically investigated by solving the Navier-Stokes equations. The time-accurate computations are performed employing an implicit algorithm based on the second-order time-accurate LU-SGS scheme with the incorporation of a subiteration procedure to maintain time accuracy. The characteristics of the flow field for a Mach number of 3.0, Reynolds number of 7.87 x 10(6)/m, and angles of attack of 5 and 10 degrees are described. Self-sustained asymmetric shock wave oscillations were observed in the numerical computations for these angles of attack. The main characteristic of the flow field, as well as its influence on drag coefficient is discussed.

Analyzing hydraulic head of fluid flow in underground porous medium

Hydraulic head is distributed through a medium with porous aspect. The analysis of hydraulic head from one point to another is used by the Richard's equation. This equation is equivalent to the groundwater ow equation that predicts the volumetric water contents. COMSOL 3.5 is used for computation applying Richard's equation. A rectangle of 100 meters of length and 10 meters of large (depth) with 0,1 m/s fl ux of inlet as source of our fl uid is simulated. The domain have Richards' equation model in two dimension (2D). Hydraulic head increases proportional with moisture content.

Modeling of Liquid-Solid Flow in Industrial Scale

In the present work, liquid-solid flow in industrial scale is modeled using the commercial software of Computational Fluid Dynamics (CFD) ANSYS Fluent 14.5. In literature, there are few studies on liquid-solid flow in industrial scale, but any information about the particular case with modified geometry cannot be found. The aim of this thesis is to describe the strengths and weaknesses of the multiphase models, when a large-scale application is studied within liquid-solid flow, including the boundary-layer characteristics. The results indicate that the selection of the most appropriate multiphase model depends on the flow regime. Thus, careful estimations of the flow regime are recommended to be done before modeling. The computational tool is developed for this purpose during this thesis. The homogeneous multiphase model is valid only for homogeneous suspension, the discrete phase model (DPM) is recommended for homogeneous and heterogeneous suspension where pipe Froude number is greater than 1.0, while the mixture and Eulerian models are able to predict also flow regimes, where pipe Froude number is smaller than 1.0 and particles tend to settle. With increasing material density ratio and decreasing pipe Froude number, the Eulerian model gives the most accurate results, because it does not include simplifications in Navier-Stokes equations like the other models. In addition, the results indicate that the potential location of erosion in the pipe depends on material density ratio. Possible sedimentation of particles can cause erosion and increase pressure drop as well. In the pipe bend, especially secondary flows, perpendicular to the main flow, affect the location of erosion.

Streamside management zone (SMZ) efficiency in herbicide retention from simulated surface flow

Plot-scale overland flow experiments were conducted to evaluate the efficiency of streamside management zones (SMZs) in retaining herbicides in runoff generated from silvicultural activities. Herbicide retention was evaluated for five different slopes (2, 5, 10, 15, and 20%), two cover conditions (undisturbed O horizon and raked surface), and two periods under contrasting soil moisture conditions (summer dry and winter wet season) and correlated to O horizon and site conditions. Picloram (highly soluble in water) and atrazine (moderately sorbed into soil particles) at concentrations in the range of 55 and 35 µg L-1 and kaolin clay (approximately 5 g L-1) were mixed with 13.000 liters of water and dispersed over the top of 5 x 10 m forested plots. Surface flow was collected 2, 4, 6, and 10 m below the disperser to evaluate the changes in concentration as it moved through the O horizon and surface soil horizon-mixing zone. Results showed that, on average, a 10 m long forested SMZ removed around 25% of the initial concentration of atrazine and was generally ineffective in reducing the more soluble picloram. Retention of picloram was only 6% of the applied quantity. Percentages of mass reduction by infiltration were 36% for atrazine and 20% for picloram. Stronger relationships existed between O horizon depth and atrazine retention than in any other measured variable, suggesting that better solid-solution contact associated with flow through deeper O horizons is more important than either velocity or soil moisture as a determinant of sorption.

CTQ process flow development and the impact for cost of quality

Tämä työ tehtiin Kone Industrial Oy:lle Major Projects yksikköön, laatuosastolle. Kone Major Projects yksikkö keskittyy erikoisiin ja suuriin hissi- ja liukuporras projekteihin. Työn tavoitteena oli luoda harmonisoitu prosessi hissikomponenttien laaduntarkkailua varten sekä tarkastella ja vertailla kustannussäästöjä, jota tällä uudella prosessilla voidaan saavuttaa. Tavoitteena oli saavuttaa 80-prosentin kustannussäästöt laatukustannuksissa uuden laatuprosessin avulla. Työn taustana ja tutkimusongelmana ovat lisääntyneet erikoisprojektit ja niiden myötä lisääntynyt laaduntarkkailun tarve. Ongelmana laaduntarkkailussa voitiin pitää harmonisoidun ja selkeän prosessin puuttumista C-prosessikomponenttien valmistuksessa. Lisäksi kehitysprosessin aikana luotiin vanhojen työkalujen pohjalta keskeinen laaduntarkkailutyökalu, CTQ-työkalu. Työssä käsitellään ensin Konetta yhtiönä ja selvitetään Koneen keskeisimmät prosessit työn taustaksi. Teoria osuudessa käsitellään prosessin kehitykseen liittyviä teorioita sekä yleisiä laatukäsitteitä ja esitetään teorioita laadun asemasta nykypäivänä. Lopuksi käsitellään COQ eli laatukustannusten teoriaa ja esitellään teoria PAF-analyysille, jota käytetään työssä laatukustannusten vertailuun case esimerkin avulla. Työssä kuvataan CTQ prosessin luominen alusta loppuun ja case esimerkin avulla testataan uutta CTQ prosessia pilottihankkeessa. Tässä case esimerkissä projektin bracket eli johdekiinnitysklipsi tuotetaan uuden laatuprosessin avulla sekä tehdään kustannusvertailu saman projektin toisen bracketin kanssa, joka on tuotettu ennen uuden laatuprosessin implementoimista. Työn lopputuloksena CTQ prosessi saatiin luotua ja sitä pystyttiin testaamaan käytännössä case esimerkin avulla. Tulosten perusteella voidaan sanoa, että CTQ prosessin käyttö vähentää laatukustannuksia huomattavasti ja helpottaa laadunhallintaa C-prosessikomponenttien tuotannossa.

Fungal succession on leaves of Alchornea triplinervia (Spreng.) Muell. Arg. submerged in a stream of an Atlantic Rainforest in the state of São Paulo, Brazil

Leaves of Alchornea triplinervia (Spreng.) Muell. Arg. were submerged in a stream in an Atlantic Rainforest in São Paulo state, Brazil, from July/1988 to June/1989 and from July/1989 to May/1990. Fungi were isolated by the leaf disks washing technique followed by plating on culture media and also by using baiting techniques (using substrates with chitin, keratin and cellulose), what resulted on 565 fungal registers corresponding to 81 taxa. The most common species found during this study of the fungal succession were Trichoderma viride Pers. ex S.F. Gray and Fusarium oxysporum Schlecht emend. Snyd. & Hans. (23 registers), Penicillium hirsutum Dierckx (21 registers), Fusarium solani (Mart.) Appel & Wollenw. emend. Snyd. & Hans. (17), followed by 14 registers of: Cylindrocladium scoparium Morgan, Triscelophorus monosporus Ingold and Polychytrium aggregatum Ajello. Although the monthly obtained mycota had been composed by species of different taxonomic groups, the fungal succession was defined by the initial presence of typical terrestrial leaf inhabiting fungi (mostly Deuteromycotina), followed by species of Mastigomycotina and Zygomycotina. Combining culture methods and baiting techniques, it was possible to verify the presence of terrestrial fungi on the decomposition of submerged leaves and the importance of zoosporic fungi in the fungal succession. This is the first paper about the fungal succession on the decomposition of leaves submerged in a lotic ecosystem in Brazil.

Interaction between the mineral content and the occurrence number of aquatic fungi in leaves submerged in a stream in the Atlantic rainforest, São Paulo, Brazil

Leaves of Ficus microcarpa L. f., Quercus robur L., and Alchornea triplinervia (Spreng.) Muell. Arg., submerged in a stream of the Atlantic rainforest in the "Reserva Biológica do Alto da Serra de Paranapiacaba", State of São Paulo, Brazil, were collected monthly, from April to November 1990, in order to determine the number of fungal occurrences (zoosporic fungi and aquatic Hyphomycetes), and the content of total N (%), total P (%), K+ (%), Ca+2 (%), Mg+2 (%), S+3 (%), Fe+3 (ppm), Cu+3 (ppm), Mn+2 (ppm), Zn+2 (ppm), Bo (ppm), Na+2 (ppm) and Al+3 (ppm). According to the tests of Kruskal-Wallis, Mann-Whitney and Wilcoxon, the means of the mineral content of the three types of leaves were significantly different, except for Mg+2 (%), Mn+2 (ppm), Zn+2 (ppm) and Na+2 (ppm). On comparing the mineral content with the number of fungal occurrence, an independence test showed a positive correlation between the presence of zoosporic fungi on the leaves of A. triplinervia and the total nitrogen, phosphorus and S+3 content, whereas the aquatic Hyphomycetes depended on the amount of Ca+2 available. Regarding leaves of F. microcarpa, the occurrence of zoosporic fungi was linked to the S+3 level, and the presence of aquatic Hyphomycetes, to the content of K+, Ca+2, S+3 and Bo. On Q. robur leaves, zoosporic fungi showed a positive correlation with the Ca+2 content, but a negative one with Fe+3 and Al+3 levels, while the occurrence of aquatic Hyphomycetes was influenced by the content of Ca+2, Mg+2, Fe+3, Al+3, Mn+2, Zn+2 and Na+2. The correlation between the occurrence number of aquatic Hyphomycetes and a high mineral content indicates that their nutritional requirements may be more complex than those of zoosporic fungi. Further studies are still required to understand the implications of this tendency on the diversity of aquatic native mycota.

The succession dynamics of a macroalgal community after a flood disturbance in a tropical stream from São Paulo State, southeastern Brazil

The succession dynamics of a macroalgal community in a tropical stream (20º58' S and 49º25' W) was investigated after disturbance by a sequence of intensive rains. High precipitation levels caused almost complete loss of the macroalgal community attached to the substratum and provided a strong pressure against its immediate re-establishment. After this disturbance, a weekly sampling program from May 1999 to January 2000 was established to investigate macroalgal recolonization. The community changed greatly throughout the succession process. The number of species varied from one to seven per sampling. Global abundance of macroalgal community did not reveal a consistent temporal pattern of variation. In early succession stages, the morphological form of tufts dominated, followed by unbranched filaments. Latter succession stages showed the almost exclusive occurrence of gelatinous forms, including filaments and colonies. The succession trajectory was mediated by phosphorus availability in which community composition followed a scheme of changes in growth forms. However, we believe that deterministic and stochastic processes occur in lotic ecosystems, but they are dependent on the length of time considered in the succession analyses.

Spatial variations at different observational scales and the seasonal distributions of stream macroalgae in a Brazilian subtropical region

We examined the relationships between environmental variations in lotic ecosystems with the seasonal dynamics of macroalgae communities at different spatial scales: drainage basin of two rivers (Rio das Pedras and Rio Marrecas), shading (open and shaded stream segments), mesohabitat (riffles and pools), and microhabitats. Data collections were made on a monthly basis between January and December/2007. A total of 16 taxa were encountered (13 species and 3 vegetative groups). All of the biotic parameters (richness, abundance, diversity, equitability, and dominance) were found to be highly variable at all of the spatial scales evaluated. On the other hand, abiotic variables demonstrated differences only at mesohabitat (in terms of current velocity) and shaded habitat (in terms of irradiance) scales. The seasonality of the macroalgae community structure was strongly influenced by microhabitat variables (current velocity, substrate H', and irradiance), demonstrating their importance over time and at different scales. Regional variables (temperature, oxygen saturation, specific conductance, pH, and turbidity) were found to have little influence on the temporal dynamics of the macroalgae communities evaluated.

Ecological distribution of stream macroalgae in different spatial scales using taxonomic and morphological groups

We examined the ecological distribution of macroalgal communities in streams using species groups (taxonomic units = algal phyla, and morphological = morphological types) with similar structures and functions instead of the species themselves. The study was conducted from June to July/2007 in two drainage basins located in mid-southern region of Paraná State , Brazil. Evaluations of macroalgal communities took into consideration the following spatial scales: the drainage basin (the Pedras river and Marrecas river basins), shading regime (open and shaded stream segments), mesohabitats (riffles and pools), and microhabitats (sampling units of 0.05m2). A total of 29 taxa (23 subgeneric, one generic, and five vegetative groups) were identified. On these, 12 taxa belong to Chlorophyta, 11 to Cyanobacteria, four to Heterokontophyta, and two to Rhodophyta. The proportions of morphological types were: 24% free filaments, 17.25% mats, tufts, gelatinous colonies, and gelatinous filaments, 7% crusts. In terms of spatial scales, we observed a predominance of Chlorophyta in open stream segments and Cyanobacteria in shaded stream segments, reflecting the loss of competitive advantage of green algae in sites with low energy availability. In the mesohabitats, the morphological types recorded in pools were predominantly poorly adapted to fast currents (free filaments), while those found in riffles (mats, tufts and gelatinous filaments) were highly resistant to fast water flows. As such, the use of species groupings based on algal taxonomy associated with morphological characteristics proved to be useful to understanding the distributions of these organisms in lotic environments.

Estimated frequency of B-chromosomes and population density of Astyanax scabripinnis paranae in a small stream

A study was made of the frequency of B-chromosomes and the population density of Astyanax scabripinnis paranae (Pisces, Characidae, Tetragonopterinae) from three stretches of the Cascatinha stream (Botucatu, SP). In the first stretch the population was estimated to be about 212 individuals and among 35 karyotyped specimens, 23 carried one macro B-chromosome; in the second stretch the population was estimated to be about 650 individuals and among 20 specimens karyotyped, two possessed one macro B-chromosome; in the third stretch the population was estimated to be about 107 individuals and among 10 specimens karyotyped, one carried one macro B-chromosome. A significant difference was observed in the frequency of macro B-chromosomes in females (57%) and males (8.7%) (P = 0.0001). These data suggest that the B-chromosome frequency and the populational density are not directly related. The hypothesis of the existence of some adaptive effect conferred by the B-chromosomes to the specimens from the first stretch of the Cascatinha stream is presented and discussed