Modeling and Parameter Estimation of Double-Star Permanent Magnet Synchronous Machines

The power rating of wind turbines is constantly increasing; however, keeping the voltage rating at the low-voltage level results in high kilo-ampere currents. An alternative for increasing the power levels without raising the voltage level is provided by multiphase machines. Multiphase machines are used for instance in ship propulsion systems, aerospace applications, electric vehicles, and in other high-power applications including wind energy conversion systems. A machine model in an appropriate reference frame is required in order to design an efficient control for the electric drive. Modeling of multiphase machines poses a challenge because of the mutual couplings between the phases. Mutual couplings degrade the drive performance unless they are properly considered. In certain multiphase machines there is also a problem of high current harmonics, which are easily generated because of the small current path impedance of the harmonic components. However, multiphase machines provide special characteristics compared with the three-phase counterparts: Multiphase machines have a better fault tolerance, and are thus more robust. In addition, the controlled power can be divided among more inverter legs by increasing the number of phases. Moreover, the torque pulsation can be decreased and the harmonic frequency of the torque ripple increased by an appropriate multiphase configuration. By increasing the number of phases it is also possible to obtain more torque per RMS ampere for the same volume, and thus, increase the power density. In this doctoral thesis, a decoupled d–q model of double-star permanent-magnet (PM) synchronous machines is derived based on the inductance matrix diagonalization. The double-star machine is a special type of multiphase machines. Its armature consists of two three-phase winding sets, which are commonly displaced by 30 electrical degrees. In this study, the displacement angle between the sets is considered a parameter. The diagonalization of the inductance matrix results in a simplified model structure, in which the mutual couplings between the reference frames are eliminated. Moreover, the current harmonics are mapped into a reference frame, in which they can be easily controlled. The work also presents methods to determine the machine inductances by a finite-element analysis and by voltage-source inverters on-site. The derived model is validated by experimental results obtained with an example double-star interior PM (IPM) synchronous machine having the sets displaced by 30 electrical degrees. The derived transformation, and consequently, the decoupled d–q machine model, are shown to model the behavior of an actual machine with an acceptable accuracy. Thus, the proposed model is suitable to be used for the model-based control design of electric drives consisting of double-star IPM synchronous machines.

Matrix Mind : on managerial reframing in multidimensional problem solving

Det är inte ovanligt att man i organisationer ställs inför problem som inte kan hanteras inom befintlig organisationsstruktur. Skälen kan vara att frågorna har många – ibland konflikterande – dimensioner och perspektiv som samtidigt måste beaktas. I den här avhandlingen studeras vilka tankemönster och föreställningar som fanns när grupper av chefer försökte lösa komplexa problem, som inte hade en naturlig organisatorisk hemvist och hur de omsatte dessa tankemönster i handling. Vad kännetecknade det ledarskap som utövades under problemlösningsprocessen? Avhandlingens empiri hämtas från ledarutvecklingsprogram i två internationellt verksamma företag i Sverige, och omfattar 14 verkliga affärsproblem i dessa företag och den process varigenom de löstes. De 14 seminarierna utgör exempel på hur mångdimensionella frågeställningar framgångsrikt hanteras utanför den befintliga organisationsstrukturen. Studien ger, genom att adressera frågor kring tankesätt och ledningsprocesser, en djupare förståelse för förutsättningarna för detta, och lyfter särskilt fram betydelsen av ett ledarskap som inbegriper begreppen intervention, förmåga och omtolkning. Som ett samlat begrepp introduceras bilden att utöva ledarskapet utifrån ett matrix mind. Att påverka strukturer (i vid mening) och därigenom de förmågor som utvecklas, är del i detta ledarskap. Det sker genom interventioner (ingrepp som påverkar relationer i t ex en grupp) och baserades i den aktuella empirin på uppfattningar om värdet av problematisering, erfarenhetsutbyte och av ett språk, som både beskriver och anger inriktning för aktiviteter. Interventioner i strukturer (och till dem knutna processer) beskriver dock bara delvis detta ledarskap. Att leda med ett matrix mind innefattar också ett nyfiket och kreativt förhållningssätt, och att utifrån detta leda omtolkning av problem. I empirin finns flera exempel på detta. Avhandlingen avser att ge ett bidrag inom såväl organisations- som ledarskapsteori.

Power semiconductor nonlinearities in active du/dt output filtering

This doctoral thesis introduces an improved control principle for active du/dt output filtering in variable-speed AC drives, together with performance comparisons with previous filtering methods. The effects of power semiconductor nonlinearities on the output filtering performance are investigated. The nonlinearities include the timing deviation and the voltage pulse waveform distortion in the variable-speed AC drive output bridge. Active du/dt output filtering (ADUDT) is a method to mitigate motor overvoltages in variable-speed AC drives with long motor cables. It is a quite recent addition to the du/dt reduction methods available. This thesis improves on the existing control method for the filter, and concentrates on the lowvoltage (below 1 kV AC) two-level voltage-source inverter implementation of the method. The ADUDT uses narrow voltage pulses having a duration in the order of a microsecond from an IGBT (insulated gate bipolar transistor) inverter to control the output voltage of a tuned LC filter circuit. The filter output voltage has thus increased slope transition times at the rising and falling edges, with an opportunity of no overshoot. The effect of the longer slope transition times is a reduction in the du/dt of the voltage fed to the motor cable. Lower du/dt values result in a reduction in the overvoltage effects on the motor terminals. Compared with traditional output filtering methods to accomplish this task, the active du/dt filtering provides lower inductance values and a smaller physical size of the filter itself. The filter circuit weight can also be reduced. However, the power semiconductor nonlinearities skew the filter control pulse pattern, resulting in control deviation. This deviation introduces unwanted overshoot and resonance in the filter. The controlmethod proposed in this thesis is able to directly compensate for the dead time-induced zero-current clamping (ZCC) effect in the pulse pattern. It gives more flexibility to the pattern structure, which could help in the timing deviation compensation design. Previous studies have shown that when a motor load current flows in the filter circuit and the inverter, the phase leg blanking times distort the voltage pulse sequence fed to the filter input. These blanking times are caused by excessively large dead time values between the IGBT control pulses. Moreover, the various switching timing distortions, present in realworld electronics when operating with a microsecond timescale, bring additional skew to the control. Left uncompensated, this results in distortion of the filter input voltage and a filter self-induced overvoltage in the form of an overshoot. This overshoot adds to the voltage appearing at the motor terminals, thus increasing the transient voltage amplitude at the motor. This doctoral thesis investigates the magnitude of such timing deviation effects. If the motor load current is left uncompensated in the control, the filter output voltage can overshoot up to double the input voltage amplitude. IGBT nonlinearities were observed to cause a smaller overshoot, in the order of 30%. This thesis introduces an improved ADUDT control method that is able to compensate for phase leg blanking times, giving flexibility to the pulse pattern structure and dead times. The control method is still sensitive to timing deviations, and their effect is investigated. A simple approach of using a fixed delay compensation value was tried in the test setup measurements. The ADUDT method with the new control algorithm was found to work in an actual motor drive application. Judging by the simulation results, with the delay compensation, the method should ultimately enable an output voltage performance and a du/dt reduction that are free from residual overshoot effects. The proposed control algorithm is not strictly required for successful ADUDT operation: It is possible to precalculate the pulse patterns by iteration and then for instance store them into a look-up table inside the control electronics. Rather, the newly developed control method is a mathematical tool for solving the ADUDT control pulses. It does not contain the timing deviation compensation (from the logic-level command to the phase leg output voltage), and as such is not able to remove the timing deviation effects that cause error and overshoot in the filter. When the timing deviation compensation has to be tuned-in in the control pattern, the precalculated iteration method could prove simpler and equally good (or even better) compared with the mathematical solution with a separate timing compensation module. One of the key findings in this thesis is the conclusion that the correctness of the pulse pattern structure, in the sense of ZCC and predicted pulse timings, cannot be separated from the timing deviations. The usefulness of the correctly calculated pattern is reduced by the voltage edge timing errors. The doctoral thesis provides an introductory background chapter on variable-speed AC drives and the problem of motor overvoltages and takes a look at traditional solutions for overvoltage mitigation. Previous results related to the active du/dt filtering are discussed. The basic operation principle and design of the filter have been studied previously. The effect of load current in the filter and the basic idea of compensation have been presented in the past. However, there was no direct way of including the dead time in the control (except for solving the pulse pattern manually by iteration), and the magnitude of nonlinearity effects had not been investigated. The enhanced control principle with the dead time handling capability and a case study of the test setup timing deviations are the main contributions of this doctoral thesis. The simulation and experimental setup results show that the proposed control method can be used in an actual drive. Loss measurements and a comparison of active du/dt output filtering with traditional output filtering methods are also presented in the work. Two different ADUDT filter designs are included, with ferrite core and air core inductors. Other filters included in the tests were a passive du/dtfilter and a passive sine filter. The loss measurements incorporated a silicon carbide diode-equipped IGBT module, and the results show lower losses with these new device technologies. The new control principle was measured in a 43 A load current motor drive system and was able to bring the filter output peak voltage from 980 V (the previous control principle) down to 680 V in a 540 V average DC link voltage variable-speed drive. A 200 m motor cable was used, and the filter losses for the active du/dt methods were 111W–126 W versus 184 W for the passive du/dt. In terms of inverter and filter losses, the active du/dt filtering method had a 1.82-fold increase in losses compared with an all-passive traditional du/dt output filter. The filter mass with the active du/dt method was 17% (2.4 kg, air-core inductors) compared with 14 kg of the passive du/dt method filter. Silicon carbide freewheeling diodes were found to reduce the inverter losses in the active du/dt filtering by 18% compared with the same IGBT module with silicon diodes. For a 200 m cable length, the average peak voltage at the motor terminals was 1050 V with no filter, 960 V for the all-passive du/dt filter, and 700 V for the active du/dt filtering applying the new control principle.

Reusing repository technology for Cultural Heritage and Special Collections

Presentation at Open Repositories 2014, Helsinki, Finland, June 9-13, 2014

Software development methods and quality assurance: Special focus on South Korea

The purpose of this study was to explore software development methods and quality assurance practices used by South Korean software industry. Empirical data was collected by conducting a survey that focused on three main parts: software life cycle models and methods, software quality assurance including quality standards, the strengths and weaknesses of South Korean software industry. The results of the completed survey showed that the use of agile methods is slightly surpassing the use of traditional software development methods. The survey also revealed an interesting result that almost half of the South Korean companies do not use any software quality assurance plan in their projects. For the state of South Korean software industry large number of the respondents thought that despite of the weakness, the status of software development in South Korea will improve in the future.

Percutaneous Coronary Intervention in Patients with Atrial Fibrillation: A Study of Factors Affecting Outcome, with a Special Emphasis on Periprocedural Antithrombotic Treatment

Antithrombotic treatment of patients with atrial fibrillation (AF) undergoing percutaneous coronary intervention (PCI) is a delicate balancing between the risk of thromboembolism and the risk of bleeding. The purpose of this dissertation was to analyze current antithrombotic treatment strategies at the periprocedural stage and report outcomes in-hospital and at 1-month follow-up, and to evaluate the effect of renal impairment and predictive values of various bleeding scores on 1-year outcome after PCI in patients with AF. The first article was based on retrospective data from 7 Finnish hospitals between 2002–2006 (n=377), while the others were based on a prospective 17-center European register (AFCAS) gathered between 2008–2010 (n=963). The main findings in patients with AF undergoing PCI were: The use of glycoprotein IIb/IIIa inhibitors during PCI was associated with a four- to five-fold increase in the risk of major bleeding (I). Uninterrupted warfarin treatment did not increase perioperative complications and seemed to decrease bleeding complications compared to heparin bridging (II). Already mild renal impairment (eGFR 60–90mL/min) was associated with a 2.3-fold risk of all-cause mortality during the 12 months following PCI (III). Major adverse cardiac events occurred in 4.5% and bleeding complications in 7.1% of patients in the AFCAS register by 1-month follow-up (IV). In a study of patients in AFCAS register, all currently used bleeding risk scores were poor predictors of bleeding complications by 1-year follow-up (V). The findings will help improve treatment strategies for this fragile patient population with a high risk of bleeding and thrombotic complications.

Concanavalin A-reactive nuclear matrix glycoprotein

The binding capacity of concanavalin A (Con A) to condensed euchromatin and heterochromatin was investigated in chicken erythrocyte nuclei (CEN), mouse liver cells, Zea mays mays meristematic cells and Drosophila melanogaster polytene chromosomes after 4 N HCl hydrolysis to determine whether binding was preferentially occurring in bands and heterochromatin. Dry mass (DM) variation was investigated in CEN by interference microscopy. Feulgen and Con A reactions were employed for all materials to correlate the loci of the two reactions. Quantifications and topological verifications were carried out by video image analysis (high performance cytometry). It was observed that 4 N HCl hydrolysis caused an important DM loss in CEN leaving a level corresponding to the average DNA DM content. In this material, Con A binding was restricted to the nuclear envelope, which reinforces the idea of the absence of a nuclear matrix in these cells. The other cell types exhibited a correspondence of Feulgen-positive and Con A-reactive areas. The Con A reaction was highly positive in the condensed chromatin areas and heterochromatin. This fact led us to speculate that Con A-positive proteins may play a role in the chromatin condensation mechanism, endowing this structure with physico-chemical stability towards acid hydrolysis and contributing to its rheological properties.

Metabolism of diglycine and triglycine by non-filtering kidneys

We have studied the metabolism of diglycine and triglycine in the isolated non-filtering rat kidney. Kidneys from adult male Wistar Kyoto rats weighing 250-350 g were perfused with Krebs-Henseleit solution containing either 1 mM diglycine or triglycine. The analysis of the peptide residues and their components was performed using an amino acid microanalyzer utilizing ion exchange chromatography. Diglycine was degraded to a final concentration of 0.09 mM after 120 min (91%); this degradation occurred predominantly during the first hour, with a 56% reduction of the initial concentration. The metabolism of triglycine occurred similarly, with a final concentration of 0.18 mM (82%); during the first hour there was a 67% reduction of the initial concentration of the tripeptide. Both peptides produced glycine in increasing concentrations, but there was a slightly lower recovery of glycine, suggesting its utilization by the kidney as fuel. The hydrolysis of triglycine also produced diglycine, which was also hydrolyzed to glycine. The results of the present study show the existence of functional endothelial or contraluminal membrane peptidases which may be important during parenteral nutrition.

Special charta öfver kusten från Söderhamn til Stockholm

Graverad af Fr. Akrel

Special passcharta öfwer een deel af Österjöön altifrån Sandhamn till Ryga : innehållandes jemwäl Moösund, samt öjarna Ösel och Dagon, med een deel af Gottland och den Curiske Wallen

Julkaisussa: General hydrographisk chart-book öfwer Östersjön och Katte-Gatt till sin raetta figur och stoorleek

Special passcharta öfwer een deel af Österjöön begynnandes ifrån Elsnabben att utwysa Stockholms-Skärgården medh heela cousten intill Gefle, samt och den Finska Skärgården till Åbo jemwäl heela Åland

Julkaisussa: General hydrographisk chart-book öfwer Östersjön och Katte-Gatt till sin raetta figur och stoorleek

Special passcharta öfwer een deel aff Österjöön begynnandes ifrån Calmarsund intill Stockholm, innehållandes jemwäl öjarna Gottland och Öland

Julkaisussa: General hydrographisk chart-book öfwer Östersjön och Katte-Gatt till sin raetta figur och stoorleek

Modulation of Signaling Molecules by Human Leucocyte Antigen B27; Special Reference to STAT1

Reactive arthritis (ReA) is an inflammatory joint disease, which belongs to the group of Spondyloarthritis (SpA). It may occur after infections with certain gram-negative bacteria such as Salmonella and Yersinia. SpAs are strongly associated with the human leucocyte antigen (HLA)-B27. Despite active research, the mechanism by which HLA-B27 causes disease susceptibility is still unknown. However, HLA-B27 has a tendency to misfold during assembly. It is possible that the misfolding of HLA-B27 could alter signaling pathways and/or molecules involved in inflammatory response in cells. We have earlier discovered that in HLA-B27-positive cells the interaction between the host and causative bacteria is disturbed. Our recent studies indicate that the expression of HLA-B27 may alter certain signaling molecules by disturbing their activation. The aim of this study was to investigate whether the expression of HLA-B27 disturbs the signaling molecules, especially the phosphorylation of transcription factor STAT1. STAT1 is an important mediator of inflammatory responses. Our results show that the phosphorylation of the STAT1 is significantly altered in HLA-B27-expressing U937 monocytic cells compared with control cells. STAT1 tyrosine 701 is more strongly phosphorylated in HLAB27- expressing cells; whereas the phosphorylation of STAT1 serine 727 is prolonged. Phosphorylation of STAT1 was discovered to be dependent on protein kinase PKR. Furthermore, we found out that the expression of posttranscriptional gene regulator HuR was altered in HLA-B27-expressing cells. We also detected that HLA-B27-positive cells secrete more interleukin 6, which is an important mediator of inflammation. These results help to understand how HLA-B27 may confer susceptibility to SpAs.