ZnO thin film surface acoustic wave based lab-on-a-chip

Lab-on-a-chip (LOC) is one of the most important microsystem applications with promise for use in microanalysis, drug development, diagnosis of illness and diseases etc. LOC typically consists of two main components: microfluidics and sensors. Integration of microfluidics and sensors on a single chip can greatly enhance the efficiency of biochemical reactions and the sensitivity of detection, increase the reaction/detection speed, and reduce the potential cross-contamination, fabrication time and cost etc. However, the mechanisms generally used for microfluidics and sensors are different, making the integration of the two main components complicated and increases the cost of the systems. A lab-on-a-chip system based on a single surface acoustic wave (SAW) actuation mechanism is proposed. SAW devices were fabricated on nanocrystalline ZnO thin films deposited on Si substrates using sputtering. Coupling of acoustic waves into a liquid induces acoustic streaming and motion of droplets. A streaming velocity up to ∼ 5cm/s and droplet pumping speeds of ∼lcm/s were obtained. It was also found that a higher order mode wave, the Sezawa wave is more effective in streaming and transportation of microdroplets. The ZnO SAW sensor has been used for prostate antigen/antibody biorecognition systems, demonstrated the feasibility of using a single actuation mechanism for lab-on-a-chip applications. © 2010 Materials Research Society.

Development of a universal stress sensor for graphene and carbon fibres

Carbon fibres are a significant volume fraction of modern structural airframes. Embedded into polymer matrices, they provide significant strength and stiffness gains by unit weight compared with competing structural materials. Here we use the Raman G peak to assess the response of carbon fibres to the application of strain, with reference to the response of graphene itself. Our data highlight the predominance of the in-plane graphene properties in all graphitic structures examined. A universal master plot relating the G peak strain sensitivity to tensile modulus of all types of carbon fibres, as well as graphene, is presented. We derive a universal value of - average - phonon shift rate with axial stress of around -5ω0 -1 (cm -1 Mpa-1), where ω0 is the G peak position at zero stress for both graphene and carbon fibre with annular morphology. The use of this for stress measurements in a variety of applications is discussed. © 2011 Macmillan Publishers Limited. All rights reserved.

Supply network integration in multi-organisational network systems

This paper explores supply network integration in complex product service systems involving close collaboration between primes. Four case study networks are studied (aerospace, naval, power and telecoms), each involving equipment manufacture and service provision. Factors that support network integration, identified from the literature and refined in the in-depth pilot case, were used to explore which processes support integration of the extended enterprise. Results suggests that a select set of processes support integration of the extended enterprise and that the absence of a shared view on these critical enabling processes results from contextual complexity of the network rather than from competing commercial interests. Copyright © 2011 Inderscience Enterprises Ltd.

Fish-makhana (Euryale salisb) integration: a case study of sustainable aquafarming system in north Bihar

The paper deals with a technique to synchronize two crops, fish and makhana (Euryale ferox Salisb) in a pond. In such eco-friendly integration both crops are mutually benefited. Decomposed plant parts of makhana crop form organic matter that releases nutrients in the water to enhance plankton population. Organic detritus not only acts as food for bottom dwelling fishes (mrigal and common carp) but also provides a suitable substratum for the growth of zooplankton, insect larvae, nematodes and gastropods. Fishes contribute to the control of makhana pests. Their faecal matter acts as organic manure for makhana crop. Plankton population fluctuated between 1260 u/l to 4030 u/l in the control pond and 1630 u/l to 4722 u/l in the experimental pond. During the grand growth period of makhana crop (April to July) the dissolved oxygen content fluctuated between 5.02 mg/l to 6.68 mg/l in the covered areas and 6.04 mg/l to 6.92 mg/l in uncovered areas. Makhana leaves acting as blanket barrier over the water surface brought down the D.O. content in the covered areas of the pond. Free CO sub(2) content showed wider fluctuation in the experimental pond (25.2 mg/l to 30.9 mg/l) than in the control pond (25.1 mg/l to 28.6 mg/l). This could be due to decomposition of plant parts of the presiding crop lying as debris at the pond bottom. Autochthonous supply of nutrients enhanced the content of nitrogen, phosphorous and organic carbon in the soil of experimental pond. The experimental pond covering an area of 0.40 ha yielded 852 kg fish and 200 kg pops whereas the control pond covering the same area produced 777 kg fish only. The net profit per ha came out to be Rs.1,04,700 and Rs. 66,200 in integrated and non-integrated system respectively. Owing to crop diversification, the present integrated system was found to be more viable than the non-integrated system in terms of production and net profit.

A high temperature SOI CMOS NO2 sensor

For more than 20 years researchers have been interested in developing micro-gas sensors based on silicon technology. Most of the reported devices are based on micro-hotplates, however they use materials that are not CMOS compatible, and therefore are not suitable for large volume manufacturing. Furthermore, they do not allow the circuitry to be integrated on to the chip. CMOS compatible devices have been previously reported. However, these use polysilicon as the heater material, which has long term stability problems at high temperatures. Here we present low power, low cost SOI CMOS NO2 sensors, based on high stability single crystal silicon P+ micro-heaters platforms, capable of measuring gas concentrations down to 0.1 ppm. We have integrated a thin tungsten molybdenum oxide layer as a sensing material with a foundry-standard SOI CMOS micro-hotplate and tested this to NO2. We believe these devices have the potential for use as robust, very low power consumption, low cost gas sensors. © 2011 American Institute of Physics.

A condition monitoring platform using COTS wireless sensor networks - Lessons and experience

Developments in Micro-Electro-Mechanical Systems (MEMS), wireless communication systems and ad-hoc networking have created new dimensions to improve asset management not only during the operational phase but throughout an asset's lifecycle based on using improved quality of information obtained with respect to two key aspects of an asset: its location and condition. In this paper, we present our experience as well as lessons learnt from building a prototype condition monitoring platform to demonstrate and to evaluate the use of COTS wireless sensor networks to develop a prototype condition monitoring platform with the aim of improving asset management by providing accurate and real-time information. © 2010 IEEE.

Magnetic sensor with compensation for lead and coil resistance

A measurement system for magnetic fields or electric currents uses a single-core fluxgate, magneto-inductive or magneto-impedance device driven from a radio frequency excitation source. Flux nulling feedback circuitry is provided to maintain the core of the sensor at substantially zero net flux and improve the linearity and dynamic response of the sensor system. A high pass filter is provided for reducing the dc effects of the ohmic resistance of the coil and lead wires on the effectiveness of the flux nulling feedback.

Fluxgate magnetic sensor with overload detection

A measurement system for magnetic fields and electric currents uses a single-core fluxgate device driven with a radio frequency excitation source and is provided with a means to indicate saturation of the core of the sensor. A means is provided for detecting overload of the sensor as the core approaches continuous saturation using a pair of demodulators and a comparator.