Mathematical Modelling of the Dynamics of Granular Materials in a Rotating Cylinder

The current study is aimed at the development of a theoretical simulation tool based on Discrete Element Method (DEM) to 'interpret granular dynamics of solid bed in the cross section of the horizontal rotating cylinder at the microscopic level and subsequently apply this model to establish the transition behaviour, mixing and segregation.The simulation of the granular motion developed in this work is based on solving Newton's equation of motion for each particle in the granular bed subjected to the collisional forces, external forces and boundary forces. At every instant of time, the forces are tracked and the positions velocities and accelarations of each partcle is The software code for this simulation is written in VISUAL FORTRAN 90 After checking the validity of the code with special tests, it is used to investigate the transition behaviour of granular solids motion in the cross section of a rotating cylinder for various rotational speeds and fill fraction.This work is hence directed towards a theoretical investigation based on Discrete Element Method (DEM) of the motion of granular solids in the radial direction of the horizontal cylinder to elucidate the relationship between the operating parameters of the rotating cylinder geometry and physical properties ofthe granular solid.The operating parameters of the rotating cylinder include the various rotational velocities of the cylinder and volumetric fill. The physical properties of the granular solids include particle sizes, densities, stiffness coefficients, and coefficient of friction Further the work highlights the fundamental basis for the important phenomena of the system namely; (i) the different modes of solids motion observed in a transverse crosssection of the rotating cylinder for various rotational speeds, (ii) the radial mixing of the granular solid in terms of active layer depth (iii) rate coefficient of mixing as well as the transition behaviour in terms of the bed turnover time and rotational speed and (iv) the segregation mechanisms resulting from differences in the size and density of particles.The transition behaviour involving its six different modes of motion of the granular solid bed is quantified in terms of Froude number and the results obtained are validated with experimental and theoretical results reported in the literature The transition from slumping to rolling mode is quantified using the bed turnover time and a linear relationship is established between the bed turn over time and the inverse of the rotational speed of the cylinder as predicted by Davidson et al. [2000]. The effect of the rotational speed, fill fraction and coefficient of friction on the dynamic angle of repose are presented and discussed. The variation of active layer depth with respect to fill fraction and rotational speed have been investigated. The results obtained through simulation are compared with the experimental results reported by Van Puyvelde et. at. [2000] and Ding et at. [2002].The theoretical model has been further extended, to study the rmxmg and segregation in the transverse direction for different particle sizes and their size ratios. The effect of fill fraction and rotational speed on the transverse mixing behaviour is presented in the form of a mixing index and mixing kinetics curve. The segregation pattern obtained by the simulation of the granular solid bed with respect to the rotational speed of the cylinder is presented both in graphical and numerical forms. The segregation behaviour of the granular solid bed with respect to particle size, density and volume fraction of particle size has been investigated. Several important macro parameters characterising segregation such as mixing index, percolation index and segregation index have been derived from the simulation tool based on first principles developed in this work.

Study on Solid Waste Management : An Economic Analysis with Respect to Ernakulam District

This thesis analyzed waste generation and waster disposal problems in municipalities and Cochin Corporation in Ernakulam district.Then the potential of resource recovery and recycling from biodegradable and non bio-degradable waste is established.The study further focused on the need for segregation of waste at the source as biodegradable and non biodegradable solid waste.The potential of resource recovery is explained in detail through the case study.The thesis also highlights the economically viable and environmental friendly methods o f treatment of waste.But the problem is that concerted and earnest attempts are lacking in making use of such methods.In spite of the health problems faced,people living near the dump sites are forced to stay there either because of their weak economic background or family ties.The study did not calculate the economic cost of health problems arising out of unscientific and irresponsible methods of waste disposal.

Characterization of Histone H2A Derived Antimicrobial Peptides, Harriottins, from Sicklefin Chimaera Neoharriotta pinnata (Schnakenbeck, 1931) and Its Evolutionary Divergence with respect to CO1 and Histone H2A

Antimicrobial peptides (AMPs) are humoral innate immune components of fishes that provide protection against pathogenic infections. Histone derived antimicrobial peptides are reported to actively participate in the immune defenses of fishes. Present study deals with identification of putative antimicrobial sequences from the histone H2A of sicklefin chimaera, Neoharriotta pinnata. A 52 amino acid residue termed Harriottin-1, a 40 amino acid Harriottin-2, and a 21 mer Harriottin-3 were identified to possess antimicrobial sequence motif. Physicochemical properties andmolecular structure ofHarriottins are in agreement with the characteristic features of antimicrobial peptides, indicating its potential role in innate immunity of sicklefin chimaera. The histone H2A sequence of sicklefin chimera was found to differ from previously reported histone H2A sequences. Phylogenetic analysis based on histone H2A and cytochrome oxidase subunit-1 (CO1) gene revealed N. pinnata to occupy an intermediate position with respect to invertebrates and vertebrates

Thermal stability of myofibrillar protein from Indian major carps

The characteristics and stability of natural actomyosin (NAM) from rohu (Labeo rohita), catla (Catla catla) and mrigal (Cirrhinus mrigala) were investigated. The total extractable actomyosin (AM) was higher (7.60mgml−1) in the case of rohu compared with that from catla and mrigal (5mgml−1). Although the specific AM ATPase activity was similar (0.43–0.5 μmolPmin−1 mgP−1) among the three species, the total ATPase activity was lower in mrigal (25 μmol g−1 meat) compared with the other species (37 μmol g−1 meat). The inactivation rate constants (kd) of AM Ca ATPase activity showed differences in the stabilities of actomyosin among these fish, the actomyosin from catla being least stable. The NAM from these species was stable up to 20 ◦C at pH 7.0. Catla AM became unstable at 30 ◦C, while rohu and mrigal AM could withstand up to 45 ◦C. The thermal denaturation with respect to solubility, turbidity, ATPase activity, sulphhydryl group and surface hydrophobicity showed noticeable changes at around these temperatures

Cumulative Approach to Customer Satisfaction with Respect to Compact Segment Car Users

Earlier studies on measurement of customer satisfaction are based on either transaction specific or overall approaches. The transaction specific approach evaluates customer satisfaction with single components in the whole purchase process but the overall satisfaction was based on all the encounters or experiences to the customer throughout the purchase process. Consumers will comment on particular events of their purchase process when asked about transaction-specific satisfaction and they will comment their overall impression and general experiences in overall satisfaction (Bitner & Hubbert 1994) Through a critical review on the literature, it has been identified a new approaches to customer satisfaction, say, cumulative approaches that can be more useful than overall and transaction specific approaches for strategic decision making (Fornell et al 1996). The cumulative approach to customer satisfaction doesn’t study earlier due to the difficulty in operationalization of the concept. But the influencers of customer satisfaction are context specific and the prevailing models doesn’t give the sources of variations in the satisfaction, the importance of cumulative approaches to customer satisfaction has emerges that lights to a new research. The current study has focused to explore the influencers of overall customer satisfaction to form individual elements that can be used to identify the cumulative customer satisfaction.

Studies on Selected Myctophid Fishes in Arabian Sea with respect to their Status in Deep Sea Trawl Bycatch, Length-Weight Relationship, Reproductive Biology and Population Dynamics

Available information on abundance of myctophids and their utilisation indicate that there is excellent scope for development of myctophid fisheries in Indian Ocean. Most of the conventional fish stocks have reached a state of full exploitation or over-exploitation. Hence there is need to locate new and conventional fishery resources in order to fill in the supply-demand gap, in the face of increasing demand for fish. Information on length-weight relationship, age and growth, spawning season, fecundity and age at maturity and information on bycatch discards are required for sustainable utilization of myctophid resource in the Indian Ocean

Piezoresistive cantilevers with an integrated bimorph actuator

Scanning Probe Microscopy (SPM) has become of fundamental importance for research in area of micro and nano-technology. The continuous progress in these fields requires ultra sensitive measurements at high speed. The imaging speed limitation of the conventional Tapping Mode SPM is due to the actuation time constant of piezotube feedback loop that keeps the tapping amplitude constant. In order to avoid this limit a deflection sensor and an actuator have to be integrated into the cantilever. In this work has been demonstrated the possibility of realisation of piezoresistive cantilever with an embedded actuator. Piezoresistive detection provides a good alternative to the usual optical laser beam deflection technique. In frames of this thesis has been investigated and modelled the piezoresistive effect in bulk silicon (3D case) for both n- and p-type silicon. Moving towards ultra-sensitive measurements it is necessary to realize ultra-thin piezoresistors, which are well localized to the surface, where the stress magnitude is maximal. New physical effects such as quantum confinement which arise due to the scaling of the piezoresistor thickness was taken into account in order to model the piezoresistive effect and its modification in case of ultra-thin piezoresistor (2D case). The two-dimension character of the electron gas in n-type piezoresistors lead up to decreasing of the piezoresistive coefficients with increasing the degree of electron localisation. Moreover for p-type piezoresistors the predicted values of the piezoresistive coefficients are higher in case of localised holes. Additionally, to the integration of the piezoresistive sensor, actuator integrated into the cantilever is considered as fundamental for realisation of fast SPM imaging. Actuation of the beam is achieved thermally by relying on differences in the coefficients of thermal expansion between aluminum and silicon. In addition the aluminum layer forms the heating micro-resistor, which is able to accept heating impulses with frequency up to one megahertz. Such direct oscillating thermally driven bimorph actuator was studied also with respect to the bimorph actuator efficiency. Higher eigenmodes of the cantilever are used in order to increase the operating frequencies. As a result the scanning speed has been increased due to the decreasing of the actuation time constant. The fundamental limits to force sensitivity that are imposed by piezoresistive deflection sensing technique have been discussed. For imaging in ambient conditions the force sensitivity is limited by the thermo-mechanical cantilever noise. Additional noise sources, connected with the piezoresistive detection are negligible.

Charakterisierung von Möhren und Weizen aus ökologischem und konventionellem Anbau anhand ihrer Carotinoid- und Polyphenolkonzentration

Kurzfassung: Der Markt für ökologische Lebensmittel wächst stark. Verbraucher kaufen Produkte aus ökologischem Landbau aus einer Vielzahl von Gründen. Ein Teil dieser Gründe lässt sich nicht auf die Produktqualität zurückführen, sondern beruht auf der Annahme, dass sich der Produktionsprozess des Ökologischen Landbaus hinsichtlich der Schonung von Umweltressourcen, der Nachhaltigkeit der Produktion und sozialen Komponenten vom konventionellen Anbau unterscheidet. Daneben spielt der Wunsch nach einer gesunden Ernährung eine Rolle. Ökologische Lebensmittel können als Vertrauensgüter verstanden werden. Lebensmittelskandale machten in den vergangenen Jahren auch vor ökologischen Lebens¬mitteln nicht Halt. Folgerichtig erschütterte dies das Vertrauen der Verbraucher in ökologische Produkte. Mit steigender Produktion könnte die Gefahr, das weitere solche Ereignisse auftreten, steigen. Daher besteht Bedarf für Methoden, die die ökologische Produktqualität im Sinne einer Authentizitätsprüfung prüfen. Eine solche Prüfung könnte sich auf die Analyse sekundärer Pflanzenstoffe stützen. Diese Gruppe von Pflanzeninhaltsstoffen spielt bei der Diskussion um die besondere Qualität ökologischer Pflanzenprodukte eine große Rolle. Postuliert wird, dass ökologisch angebaute Pflanzen mangels mineralischer Düngung und mangels Schädlingsbekämpfung mit synthetischen Pestiziden einem erhöhten Stress ausgesetzt sind. Dies soll sich in einem höheren Niveau der mit den Selbstverteidigungsmechanismen der Pflanze eng verbundenen sekundären Pflanzenstoffe ausdrücken. Wichtige Untergruppen der sekundären Pflanzenstoffe sind Carotinoide und Polyphenole. An Weizen (Triticum aestivum L. und Triticum durum L.) und Möhre (Daucus carota L.) als für den ökologischen Landbau wichtigen Produkten wurden Messungen der Carotinoid- und Polyphenolkonzentration mit dem Ziel durchgeführt, die potentielle Eignung dieser Pflanzenstoffe als Biomarker zur Authentizitätsprüfung ökologischer Produkte zu evaluieren. Dazu wurden Proben aus ökologischem und konventionellem Anbau (Paarvergleich) untersucht. Diese stammten aus Langzeit-Feldversuchen (Weizen aus dem DOK- und dem MASCOT-Versuch), Feldversuchen und von Betriebspaaren untersucht. Ein generell höheres Niveau sekundärer Pflanzenstoffe in Möhren bzw. Weizen aus ökologischem Anbau gegenüber Proben aus konventionellem Anbau wurde nicht gefunden. Die Carotinoide waren weder bei der Möhre noch beim Weizen zur Authentizitätsprüfung geeignet. Die Konzentration der Carotinoide wurde stark durch die nicht dem Anbau¬verfahren zuzuordnenden Faktoren Klima, Sorte und Standort beeinflusst. Die Luteinkonzentration war das einzige durch das Anbauverfahren systematisch beeinflusste Carotenoid bei Weizen und Möhre. Die Unterschiede der Luteinkonzentration waren aber im Paarvergleich von Proben (ökologischer versus konventioneller Anbau) nicht durchgängig signifikant. Die Eignung von Polyphenolen als potentielles Authentizitätskriterium wurde nur an Möhren geprüft. Im Paarvergleich unterschieden sich die Konzentrationen einzelner Polyphenole signifikant und konsistent über Probenjahre und Standorte, nicht jedoch über Sorten hinweg. Wie bei den Carotinoiden konnte auch hier ein starker Einfluss von Probenjahr, Standort und Sorte gezeigt werden. Trotz der Variation durch diese nicht dem Anbau zuzuordnenden Faktoren war eine korrekte Klassifizierung der Proben nach Anbauverfahren möglich. Dies wurde mittels Diskriminanzanalyse getestet. Die Polyphenole sind daher potentiell als Authentizitätskriterium geeignet.

Biofilmbildung bei Pflanzen-assoziierten Bakterien der Gattung Methylobacterium und molekulargenetisch-physiologische Charakterisierung eines neuen Marchantia-Isolats (Mtb. sp. JT1)

Bakterien existieren bevorzugt in Biofilmen. Das Zusammenleben in diesen Gemeinschaften bietet den einzelnen Mikroben einen wirksamen Schutz und ermöglicht die Ausbildung langfristiger, synergistischer Wechselwirkungen, die mit multizellulären Systemen verglichen werden können. Biofilme bestehen aus Mikrooganismen-Populationen, die sich an Grenzflächen ansammeln und typischerweise von einer Matrix aus extrazellulären polymeren Substanzen umgeben sind. Auch auf Pflanzen-Oberflächen bilden viele Bakterien Biofilme, um ihre Überlebenswahrscheinlichkeit zu erhöhen. In dieser Arbeit wurde die Biofilmbildung bei Pflanzen-assoziierten Bakterien der Gattung Methylobacterium (Mtb.) untersucht, wobei molekular- und mikrobiologische sowie mikroskopische Techniken eingesetzt wurden. Es zeigte sich, dass alle untersuchten Vertreter der Gattung Methylobacterium in unterschiedlichem Ausmaß Biofilme bilden. Die Ausprägung ist dabei Taxon (bzw. Isolat)-spezifisch und vor allem von der Stickstoff-Verfügbarkeit abhängig. Jedoch spielen auch andere Umweltfaktoren, wie die Versorgung der Zellen mit Phosphat und die Zelldichte, bei der Ausbildung der überzellulären Einheiten eine wichtige Rolle. Die Matrix der Biofilme wird meist durch ein fibrilläres Netzwerk gebildet. Dabei handelt es sich um Heteropolysaccharide, die von den Bakterien synthetisiert und sezerniert werden. Einige Isolate bilden zusätzlich zahlreiche Fimbrien (Auswüchse), durch die sie an andere Zellen oder Oberflächen binden können. Im zweiten Teil dieser Arbeit wurden mehrere neue Methylobacterium-Isolate physiologisch und molekulargenetisch charakterisiert (Nährstoffverwertung, DNA-Sequenzen verschiedener Gene, phylogenetische Analysen usw.). Im Vordergrund stand hierbei der von einer urtümlichen Landpflanze, dem Lebermoos (Marchantia polymorpha), isolierte Stamm Mtb. sp. JT1. Dabei zeigten sich deutliche Unterschiede in der Morphologie und Physiologie des Bakterienstamms JT1 und dem nahe verwandten Stamm 5b.2.20 zu den bereits beschriebenen Taxa der Gattung, so dass eine Spezies-Neubeschreibung erforderlich war. Als Artname wurde aufgrund der außergewöhnlichen Oberflächenstrukturen Mtb. fimbriae sp. nov. eingeführt. Auch andere Methylobakterien (unter anderem Isolat Mtb. sp. F3.2, isoliert vom Laubmoos Funaria hygrometrica) stellen wahrscheinlich Vertreter einer neue Spezies dar (Artname Mtb. funariae sp. nov.). Jedoch zeigen Mtb. fimbriae und Mtb. funariae nur geringe physiologische und morphologische Unterschiede und konnten auf Grundlage umfassender DNA-DNA-Hybridisierungs-Studien nicht eindeutig voneinander abgegrenzt werden.

Untersuchungen zum Vorkommen und molekularen Mechanismus der Biofilm-Bildung bei Enterokokken aus verschiedenen klinischen Bereichen

Im Rahmen der vorliegenden Arbeit wurde eine größere Anzahl an E. faecalis Isolaten aus Vaginalabstrichen, erstmals insbesondere von Patientinnen, die an Bakterieller Vaginose litten, untersucht und mit E. faecalis Stämme aus verschiedenen anderen klinischen Bereichen auf das Vorkommen von Virulenzfaktoren verglichen. Weiterhin wurden Korrelationen zwischen bestimmten Faktoren und der Menge an produziertem Biofilm erstellt, um mögliche Zusammenhänge zum Mechanismus der Biofilm-Bildung zu erfassen. Mittels statistischer Analysen konnte hinsichtlich der 150 untersuchten E. faecalis Isolate nachgewiesen werden, dass keine signifikanten Unterschiede der Inzidenzen von Virulenzfaktoren (esp, asa1, gelE, GelE, cylA, β-Hämolyse) zwischen den Stämmen der verschiedenen Herkunftsbereiche bestanden. In Bezug auf das Auftreten von Biofilm-Bildung zeigte sich ein erhöhtes Vorkommen bei Stämmen aus Urin sowie invasiver Herkunft (insgesamt jeweils ca. 70 % mäßige und starke Biofilm-Bildner) im Vergleich zu E. faecalis Isolaten aus Wunden oder Faeces (je ca. 40 %). Statistische Auswertungen bzgl. des Zusammenhangs eines oder einer Kombination von Virulenzfaktoren mit der Menge an gebildetem Biofilm wiesen darauf hin, dass Isolate, die das esp Gen besaßen, in erhöhtem Maße zur Biofilm-Bildung befähigt waren. Dies zeigte einen gewissen Einfluss des Zellwandproteins auf die Fähigkeit zur Biofilm-Bildung bei E. faecalis. Allerdings wurden stets auch Stämme identifiziert, die die Fähigkeit zur Biofilm-Bildung trotz des Fehlens der jeweils untersuchten genetischen Determinante bzw. der Determinanten aufwiesen, so dass auf das Vorhandensein weiterer, unbekannter Einflussfaktoren auf den Mechanismus der Biofilm-Bildung bei E. faecalis geschlossen werden konnte. Unter 78 untersuchten E. faecium Isolaten aus verschiedenen klinischen Bereichen konnte lediglich ein Stamm (1,3 %) als mäßiger Biofilm-Bildner charakterisiert werden, so dass die Fähigkeit bei dieser Spezies in der hier untersuchten Region unter diesen Bedingungen kaum nachgewiesen werden konnte. Einen Schwerpunkt dieser Arbeit bildete die Untersuchung zum Vorkommen von Virulenzfaktoren und Biofilm-Bildung bei E. faecalis Isolaten aus Vaginalabstrichen. Bzgl. des Auftretens von Virulenzfaktoren und Biofilm-Produktion konnte kein Unterschied zwischen Stämmen assoziiert mit Bakterieller Vaginose und Isolaten einer Vergleichsgruppe festgestellt werden. Allerdings zeigte eine Gegenüberstellung mit den untersuchten E. faecalis Stämmen aus anderen klinischen Bereichen, dass die 80 Isolate aus Vaginalabstrichen eine ähnlich hohe Inzidenz bestimmter Virulenzfaktoren wie Stämme aus Faeces, Urin, Wunden oder invasiver Herkunft sowie eine mit den Isolaten aus Urin und invasiver Herkunft vergleichbar hohe Fähigkeit zur Biofilm-Bildung aufwiesen (ca. 75 % mäßige und starke Biofilm-Bildner). Dies deutete auf eine Verbreitung der Biofilm-Bildungsfähigkeit bei E. faecalis Stämmen der Vaginalflora und somit auf eine große Bedeutung der Eigenschaft für Isolate dieser Herkunft hin. Die statistische Auswertung der Korrelationen von Virulenzfaktoren mit der Menge an gebildetem Biofilm lieferte ähnliche Ergebnisse wie die Analysen bzgl. der 150 E. faecalis Isolate aus anderen klinischen Bereichen und untermauerte die Annahme, dass zusätzliche Faktoren zu den hier untersuchten Determinanten bei E. faecalis vorhanden sein müssen, die Einfluss auf den Mechanismus der Biofilm-Bildung nehmen. Deshalb konzentrierte sich ein weiterer Teil der vorliegenden Arbeit auf die Herstellung und Charakterisierung von E. faecalis Biofilm-Spontanmutanten, um bisher noch ungeklärte Mechanismen oder neue Faktoren zu erkennen, die Einfluss auf die Biofilm-Bildung bei E. faecalis nehmen. Die Untersuchung einer Mutante (1.10.16) und ihres Wildtypstamms lieferte erstmals den phänotypischen Nachweis des HMW-Komplexes der drei Bee-Proteine sowie die Identifizierung konservierter Pili-Motive dieser Proteine. Des Weiteren schien die in diesem Cluster ebenfalls codierte Sortase-1 dasjenige Enzym zu sein, das höchstwahrscheinlich die Bindung des Proteins Bee-2 innerhalb dieses HMW-Komplexes katalysiert. Insofern lieferten diese Untersuchungen neue, konkrete Hinweise zur Rolle des bee Genclusters bei der Pili-Biogenese und Biofilm-Bildung von E. faecalis. Darüber hinaus stellen Erkenntnisse aus der Charakterisierung von zwei weiteren hergestellten Biofilm-Spontanmutanten viel versprechende Ausgangspunkte für zukünftige Untersuchungen dar, die ein weitergehendes Verständnis der molekularen Mechanismen der Biofilm-Bildung bei E. faecalis erzielen könnten.

Development and Integration of Biocontrol Products in Branched Broomrape (Phelipanche ramosa) management in Tomato

Parasitic weeds of the genera Striga, Orobanche, and Phelipanche pose a severe problem for agriculture because they are difficult to control and are highly destructive to several crops. The present work was carried out during the period October, 2009 to February, 2012 to evaluate the potential of arbuscular mycorrhizal fungi (AMF) to suppress P. ramosa on tomatoes and to investigate the effects of air-dried powder and aqueous extracts from Euphorbia hirta on germination and haustorium initiation in Phelipanche ramosa. The work was divided into three parts: a survey of the indigenous mycorrhizal flora in Sudan, second, laboratory and greenhouse experiments (conducted in Germany and Sudan) to construct a base for the third part, which was a field trial in Sudan. A survey was performed in 2009 in the White Nile state, Sudan to assess AMF spore densities and root colonization in nine fields planted with 13 different important agricultural crops. In addition, an attempt was made to study the relationship between soil physico-chemical properties and AMF spore density, colonization rate, species richness and other diversity indices. The mean percentage of AMF colonization was 34%, ranging from 19-50%. The spore densities (expressed as per 100 g dry soil) retrieved from the rhizosphere of different crops were relatively high, varying from 344 to 1222 with a mean of 798. There was no correlation between spore densities in soil and root colonization percentage. A total of 45 morphologically classifiable species representing ten genera of AMF were detected with no correlation between the number of species found in a soil sample and the spore density. The most abundant genus was Glomus (20 species). The AMF diversity expressed by the Shannon–Weaver index was highest in sorghum (H\= 2.27) and Jews mallow (H\= 2.13) and lowest in alfalfa (H\= 1.4). With respect to crop species, the genera Glomus and Entrophospora were encountered in almost all crops, except for Entrophospora in alfalfa. Kuklospora was found only in sugarcane and sorghum. The genus Ambispora was recovered only in mint and okra, while mint and onion were the only species on which no Acaulospora was found. The hierarchical cluster analysis based on the similarity among AMF communities with respect to crop species overall showed that species compositions were relatively similar with the highest dissimilarity of about 25% separating three of the mango samples and the four sorghum samples from all other samples. Laboratory experiments studied the influence of root and stem exudates of three tomato varieties infected by three different Glomus species on germination of P. ramosa. Root exudates were collected 21or 42 days after transplanting (DAT) and stem exudates 42 DAT and tested for their effects on germination of P. ramosa seeds in vitro. The tomato varieties studied did not have an effect on either mycorrhizal colonization or Phelipanche germination. Germination in response to exudates from 42 day old mycorrhizal plants was significantly reduced in comparison to non-mycorrhizal controls. Germination of P. ramosa in response to root exudates from 21 day old plants was consistently higher than for 42 day-old plants (F=121.6; P<.0001). Stem diffusates from non-mycorrhizal plants invariably elicited higher germination than diffusates from the corresponding mycorrhizal ones and differences were mostly statistically significant. A series of laboratory experiments was undertaken to investigate the effects of aqueous extracts from Euphorbia hirta on germination, radicle elongation, and haustorium initiation in P. ramosa. P. ramosa seeds conditioned in water and subsequently treated with diluted E. hirta extract (10-25% v/v) displayed considerable germination (47-62%). Increasing extract concentration to 50% or more reduced germination in response to the synthetic germination stimulants GR24 and Nijmegen-1 in a concentration dependent manner. P. ramosa germlings treated with diluted Euphorbia extract (10-75 % v/v) displayed haustorium initiation comparable to 2, 5-Dimethoxy-p-benzoquinon (DMBQ) at 20 µM. Euphorbia extract applied during conditioning reduced haustorium initiation in a concentration dependent manner. E. hirta extract or air-dried powder, applied to soil, induced considerable P. ramosa germination. Pot experiments were undertaken in a glasshouse at the University of Kassel, Germany, to investigate the effects of P. ramosa seed bank on tomato growth parameters. Different Phelipanche seed banks were established by mixing the parasite seeds (0 - 32 mg) with the potting medium in each pot. P. ramosa reduced all tomato growth parameters measured and the reduction progressively increased with seed bank. Root and total dry matter accumulation per tomato plant were most affected. P. ramosa emergence, number of tubercles, and tubercle dry weight increased with the seed bank and were, invariably, maximal with the highest seed bank. Another objective was to determine if different AM fungi differ in their effects on the colonization of tomatoes with P. ramosa and the performance of P. ramosa after colonization. Three AMF species viz. GIomus intraradices, Glomus mosseae and Glomus Sprint® were used in this study. For the infection, P. ramosa seeds (8 mg) were mixed with the top 5 cm soil in each pot. No mycorrhizal colonization was detected in un-inoculated control plants. P. ramosa infested, mycorrhiza inoculated tomato plants had significantly lower AMF colonization compared to plants not infested with P. ramosa. Inoculation with G. intraradices, G. mosseae and Glomus Sprint® reduced the number of emerged P. ramosa plants by 29.3, 45.3 and 62.7% and the number of tubercles by 22.2, 42 and 56.8%, respectively. Mycorrhizal root colonization was positively correlated with number of branches and total dry matter of tomatoes. Field experiments on tomato undertaken in 2010/12 were only partially successful because of insect infestations which resulted in the complete destruction of the second run of the experiment. The effects of the inoculation with AMF, the addition of 10 t ha-1 filter mud (FM), an organic residues from sugar processing and 36 or 72 kg N ha-1 on the infestation of tomatoes with P. ramosa were assessed. In un-inoculated control plants, AMF colonization ranged between 13.4 to 22.1% with no significant differences among FM and N treatments. Adding AMF or FM resulted in a significant increase of branching in the tomato plants with no additive effects. Dry weights were slightly increased through FM application when no N was applied and significantly at 36 kg N ha-1. There was no effect of FM on the time until the first Phelipanche emerged while AMF and N application interacted. Especially AMF inoculation resulted in a tendency to delayed P. ramosa emergence. The marketable yield was extremely low due to the strong fruit infestation with insects mainly whitefly Bemisia tabaci and tomato leaf miner (Tuta absoluta). Tomatoes inoculated with varied mycorrhiza species displayed different response to the insect infestation, as G. intraradices significantly reduced the infestation, while G. mosseae elicited higher insect infestation. The results of the present thesis indicate that there may be a potential of developing management strategies for P. ramosa targeting the pre-attachment stage namely germination and haustorial initiation using plant extracts. However, ways of practical use need to be developed. If such treatments can be combined with AMF inoculation also needs to be investigated. Overall, it will require a systematic approach to develop management tools that are easily applicable and affordable to Sudanese farmers. It is well-known that proper agronomical practices such as the design of an optimum crop rotation in cropping systems, reduced tillage, promotion of cover crops, the introduction of multi-microbial inoculants, and maintenance of proper phosphorus levels are advantageous if the mycorrhiza protection method is exploited against Phelipanche ramosa infestation. Without the knowledge about the biology of the parasitic weeds by the farmers and basic preventive measures such as hygiene and seed quality control no control strategy will be successful, however.

Knowledge Building in Landscape Architecture

The objective of this study was to develop an internet-based seminar framework applicable for landscape architecture education. This process was accompanied by various aims. The basic expectation was to keep the main characteristics of landscape architecture education also in the online format. On top of that, four further objectives were anticipated: (1) training of competences for virtual team work, (2) fostering intercultural competence, (3) creation of equal opportunities for education through internet-based open access and (4) synergy effects and learning processes across institutional boundaries. This work started with the hypothesis that these four expected advantages would compensate for additional organisational efforts caused by the online delivery of the seminars and thus lead to a sustainable integration of this new learning mode into landscape architecture curricula. This rationale was followed by a presentation of four areas of knowledge to which the seminar development was directly related (1) landscape architecture as a subject and its pedagogy, (2) general learning theories, (3) developments in the ICT sector and (4) wider societal driving forces such as global citizenship and the increase of open educational resources. The research design took the shape of a pedagogical action research cycle. This approach was constructive: The author herself is teaching international landscape architecture students so that the model could directly be applied in practice. Seven online seminars were implemented in the period from 2008 to 2013 and this experience represents the core of this study. The seminars were conducted with varying themes while its pedagogy, organisation and the technological tools remained widely identical. The research design is further based on three levels of observation: (1) the seminar design on the basis of theory and methods from the learning sciences, in particular educational constructivism, (2) the seminar evaluation and (3) the evaluation of the seminars’ long term impact. The seminar model itself basically consists of four elements: (1) the taxonomy of learning objectives, (2) ICT tools and their application and pedagogy, (3) process models and (4) the case study framework. The seminar framework was followed by the presentation of the evaluation findings. The major findings of this study can be summed up as follows: Implementing online seminars across educational and national boundaries was possible both in term of organisation and technology. In particular, a high level of cultural diversity among the seminar participants has definitively been achieved. However, there were also obvious obstacles. These were primarily competing study commitments and incompatible schedules among the students attending from different academic programmes, partly even in different time zones. Both factors had negative impact on the individual and working group performances. With respect to the technical framework it can be concluded that the majority of the participants were able to use the tools either directly without any problem or after overcoming some smaller problems. Also the seminar wiki was intensively used for completing the seminar assignments. However, too less truly collaborative text production was observed which could be improved by changing the requirements for the collaborative task. Two different process models have been applied for guiding the collaboration of the small groups and both were in general successful. However, it needs to be said that even if the students were able to follow the collaborative task and to co-construct and compare case studies, most of them were not able to synthesize the knowledge they had compiled. This means that the area of consideration often remained on the level of the case and further reflections, generalisations and critique were largely missing. This shows that the seminar model needs to find better ways for triggering knowledge building and critical reflection. It was also suggested to have a more differentiated group building strategy in future seminars. A comparison of pre- and post seminar concept maps showed that an increase of factual and conceptual knowledge on the individual level was widely recognizable. Also the evaluation of the case studies (the major seminar output) revealed that the students have undergone developments of both the factual and the conceptual knowledge domain. Also their self-assessment with respect to individual learning development showed that the highest consensus was achieved in the field of subject-specific knowledge. The participants were much more doubtful with regard to the progress of generic competences such as analysis, communication and organisation. However, 50% of the participants confirmed that they perceived individual development on all competence areas the survey had asked for. Have the additional four targets been met? Concerning the competences for working in a virtual team it can be concluded that the vast majority was able to use the internet-based tools and to work with them in a target-oriented way. However, there were obvious differences regarding the intensity and activity of participation, both because of external and personal factors. A very positive aspect is the achievement of a high cultural diversity supporting the participants’ intercultural competence. Learning from group members was obviously a success factor for the working groups. Regarding the possibilities for better accessibility of educational opportunities it became clear that a significant number of participants were not able to go abroad during their studies because of financial or personal reasons. They confirmed that the online seminar was to some extent a compensation for not having been abroad for studying. Inter-institutional learning and synergy was achieved in so far that many teachers from different countries contributed with individual lectures. However, those teachers hardly ever followed more than one session. Therefore, the learning effect remained largely within the seminar learning group. Looking back at the research design it can be said that the pedagogical action research cycle was an appropriate and valuable approach allowing for strong interaction between theory and practice. However, some more external evaluation from peers in particular regarding the participants’ products would have been valuable.

The Dirichlet distribution with respect to the Aitchison measure on the simplex - a first approach

The algebraic-geometric structure of the simplex, known as Aitchison geometry, is used to look at the Dirichlet family of distributions from a new perspective. A classical Dirichlet density function is expressed with respect to the Lebesgue measure on real space. We propose here to change this measure by the Aitchison measure on the simplex, and study some properties and characteristic measures of the resulting density

Sex differences in oppositional defiant disorder

Resumen tomado de la publicaci??n