AMS radiocarbon dates on ten monospecific samples of planktonic foraminifer Globigerinoides ruber of sediment core GeoB8509-2 (Table 1)

Aeolian and fluvial sediment transport to the Atlantic Ocean offshore Mauritania were reconstructed based on grain-size distributions of the carbonate-free silt fraction of three marine sediment records of Cap Timiris Canyon to monitor the climatic evolution of present-day arid north-western Africa. During the late Pleistocene, predominantly coarse-grained particles, which are interpreted as windborne dust, characterise glacial dry climate conditions with a low sea level and extended sand seas that reach onto the exposed continental shelf off Mauritania. Subsequent particle fining and the abrupt decrease in terrigenous supply are attributed to humid climate conditions and dune stabilisation on the adjacent African continent with the onset of the Holocene humid period. Indications for an ancient drainage system, which was discharging fluvial mud offshore via Cap Timiris Canyon, are provided by the finest end member for early to mid Holocene times. However, in comparison to the Senegal and Niger River further south, the river system connecting Cap Timiris Canyon with the Mauritanian hinterland was starved during the late Holocene and is non-discharging under present-day arid climate conditions.

Documentation of sediment core PS1392-1

The Late Quaternary sediment sequence of the continental margin in the eastern Weddell Sea is well suited for palaeoenvironmental reconstructions. Two cores from the upper slope, which contain the sedimentary record of the last 300 ky, have been sedimentologically investigated. Age models are based on lithostratigraphy and are correlated with the stable isotope record. As a result of a detailed analysis of the clay mineral composition, grain size distributions and structures, this sedimentary record provides the first marine evidence that the Antarctic ice sheet extended to the shelf edge during the last glacial. The variations in volume and size of the ice sheet were also simulated in numerical models. Changes in accumulation rate and ice temperature are of some importance, but the model revealed that fluctuations are primarily driven by changes in eustatic sea-level and that the ice edge extended to the shelf edge during the last glacial maximum. This causal relationship implies that the maximum ice extension strongly depends on the magnitude and duration of the sea-level depression during a glacial period. The results of the sedimentological investigations and of the numerical models show that the Antarctic ice sheet follows glacial events in the northern hemisphere by teleconnections of sea level.

Temperatures, salinity, wind speed, grain sizes and foraminifera abundance in the Great Belt Channel, western Baltic Sea

The Great Belt, the largest inlet to the Baltic Sea, has a deep and well defined channel system. A distinct thermohaline layer at roughly 18 to 20 m of water depth separates the saltier and generally cooler deeper North Sea water from the brackish and warmer surface water. It is practically a current dominated area, with the strongest bottom currents due to prolonged west winds. The size and shape of the surface sediments and their grain size distributions show a close relationship with the prevailing hydrographical conditions. Southerly current marks predominate while northerly directions are confined to 10 to 14 m of water depth. The degree of bioturbation is highest in the uppermost sedimentary cover where practically all original stratification has been destroyed. Various bioturbate structures have been identified with the fauna. Coiling ratios of Ammonia beccarii (Linnaeus) have been successfully applied for correlation in the postglacial sediments of the early Littorina Transgression. The succession shows that in the Boreal brackish water conditions were probably followed by peat and limnic sediments as the sea regressed. With the Littorina Transgression, the sea again entered the area and high sedimentation rates resulted in the major deposits of the Great Belt. At least for the last 4000 years, sedimentation rates had been very low. Present day currents sweep out the sediments, mainly to the southern marginal areas.

Sedimentology on surface samples from the White Sea

In this study, the grain-size and clay-mineral compositions of 73 surface sediment samples collected in a variety of environmental settings in the White Sea are presented to characterize recent sedimentation processes, reconstruct transport pathways, and identify potential source areas of the terrigenous components. Areas >100 m deep are invariably characterized by silty clay, whereas areas <100 m deep exhibit more heterogeneous grain-size compositions plausibly explained by coastal erosion and (re-)distribution mechanisms, particularly tidal currents. The dominance of sand in the estuarine areas of the Onega and Dvina rivers as well as toward Gorlo Strait connecting the White Sea with the Barents Sea, is attributed to increased current speeds. Illite and smectite are the dominant clay minerals in recent sediments of the southwestern and eastern White Sea sectors, respectively. Their distribution patterns largely depend on the geology of the source areas and mirror surface circulation patterns, especially in Dvina Bay. Smectite is a key clay mineral in White Sea surface sediments as it reveals the dominating influence of the Northern Dvina's runoff on sedimentation and water circulation throughout the basin of the sea. In comparison to other Eurasian shelf seas, the White Sea is characterized by a greater diversity of clay-mineral assemblages, which range from illite- to smectite-dominated sectors containing variable amounts of chlorite and kaolinite.

Community structure of sulfate reducing bacteria in the sediment of the arctic Smeerenburgfjorden

The community structure of sulfate-reducing bacteria (SRB) of a marine Arctic sediment (Smeerenburgfjorden, Svalbard) was characterized by both fluorescence in situ hybridization (FISH) by using group- and genus-specific 16S rRNA-targeted oligonucleotide probes. Samples stored in PBS-ethanol were diluted and treated by mild sonication. A 10-ml aliquot of a 1:40 dilution was filtered onto a 0.2-mm-pore-size type GTTP polycarbonate filter (Millipore, Eschborn, Germany). Hybridization and microscopic counting of hybridized and 49,69-diamidino-2-phenylindole (DAPI)-stained cells were performed as described previously from Snaidr et al. (1997, http://aem.asm.org/content/63/7/2884.full.pdf). Details of probes and formamide concentrations which were used are listed in futher details.. Means were calculated by using 10 to 20 randomly chosen fields for each filter section, which corresponded to 800 to 1,000 DAPI-stained cells. Counting results were always corrected by subtracting signals observed with probe NON338. The SRB community was dominated by members of the Desulfosarcina-Desulfococcus group. This group accounted for up to 73% of the SRB detected. The predominance was shown to be a common feature for different stations along the coast of Svalbard. In a top-to-bottom approach we aimed to further resolve the composition of this large group of SRB by using probes for cultivated genera. While this approach failed, directed cloning of probe-targeted genes encoding 16S rRNA was successful and resulted in sequences which were all affiliated with the Desulfosarcina-Desulfococcus group. A group of clone sequences (group SVAL1) most closely related to Desulfosarcina variabilis (91.2% sequence similarity) was dominant and was shown to be most abundant in situ, accounting for up to 54.8% of the total SRB detected.

Broad-scale patterns of sex ratios in Patella spp.: a comparison of range edge and central range populations in the British Isles and Portugal

Sex change, or sequential hermaphroditism, occurs in the plant and animal kingdoms and often determines a predominance of the first sex. Our aim was to explore changes in sex ratios within the range of the species studied: Patella vulgata and Patella depressa. The broad-scale survey of sex with size of limpets covered a range of latitudes from Zambujeira do Mar (southern Portugal) to the English Channel. Indirect evidence was found for the occurrence of protandry in P. vulgata populations from the south of England, with females predominating in larger size-classes; cumulative frequency distributions of males and females were different; sex ratios were biased towards males and smallest sizes of males were smaller than the smallest sizes of females. In contrast in Portugal females were found in most size-classes of P. vulgata. In P. depressa populations from the south coast of England and Portugal females were interspersed across most size-classes; size distributions of males and females and size at first maturity of males and females did not differ. P. depressa did, however, show some indications of the possibility of slight protandry occurring in Portugal. The test of sex ratio variation with latitude indicated that P. vulgata sex ratios might be involved in determining the species range limit, particularly at the equatorward limit since the likelihood of being male decreased from the south coast of England to southern Portugal. Thus at the southern range limit, sperm could be in short supply due to scarcity of males contributing to an Allee effect.

Broad-scale patterns of sex ratios in Patella spp.: a comparison of range edge and central range populations in the British Isles and Portugal

Sex change, or sequential hermaphroditism, occurs in the plant and animal kingdoms and often determines a predominance of the first sex. Our aim was to explore changes in sex ratios within the range of the species studied: Patella vulgata and Patella depressa. The broad-scale survey of sex with size of limpets covered a range of latitudes from Zambujeira do Mar (southern Portugal) to the English Channel. Indirect evidence was found for the occurrence of protandry in P. vulgata populations from the south of England, with females predominating in larger size-classes; cumulative frequency distributions of males and females were different; sex ratios were biased towards males and smallest sizes of males were smaller than the smallest sizes of females. In contrast in Portugal females were found in most size-classes of P. vulgata. In P. depressa populations from the south coast of England and Portugal females were interspersed across most size-classes; size distributions of males and females and size at first maturity of males and females did not differ. P. depressa did, however, show some indications of the possibility of slight protandry occurring in Portugal. The test of sex ratio variation with latitude indicated that P. vulgata sex ratios might be involved in determining the species range limit, particularly at the equatorward limit since the likelihood of being male decreased from the south coast of England to southern Portugal. Thus at the southern range limit, sperm could be in short supply due to scarcity of males contributing to an Allee effect.

Evaporative Moisture Loss from Heterogeneous Stone: Material- Environment Interactions During Drying

The complexities of evaporation from structurally and mineralogically heterogeneous sandstone (Locharbriggs Sandstone) are investigated through a laboratory-based experiment in which a variety of environmental conditions are simulated. Data reported demonstrate the significance of material-environment interactions on the spatial and temporal variability of evaporative dynamics. Evaporation from porous stone is determined by the interplay between environmental, material and solution properties, which govern the rate and mode by which water is transmitted to, and subsequently removed from, an evaporating surface. Initially evaporation is marked by high rates of moisture loss controlled by external atmospheric conditions; then, when a critical level of surface moisture content is reached, hydraulic continuity between the stone surface and subsurface is disrupted and the drying front recedes
beneath the surface, evaporation rates decrease and are controlled by the ability of the material to transport water vapour to the surface. Pore size distribution and connectivity, as well as other material properties, control the timing of each stage of evaporation and the nature of the transition.

These experimental data highlight the complexity of evaporation, demonstrating that different regions of the same stone can exhibit varying moisture dynamics during drying and that the rate and nature of evaporative loss differs under different environmental conditions. The results identify the importance of material-environment interactions during drying and that stone micro-environmental conditions cannot be inferred from ambient data alone.
These data have significance for understanding the spatial distribution of stone surface weathering-related morphologies in both the natural and built environments where mineralogical and/or structural heterogeneity creates differences in moisture flux and hence variable drying rates. Such differences may provide a clearer explanation for the initiation and subsequent development of complex weathering responses where areas of significant deterioration can be found alongside areas that exhibit little or no evidence surface breakdown.

Absorption of Asphalt by Aggregate, HR-142, Progress Report, 1970

This report summarizes work accomplished under Project HR-142 during the period from January 1, 1969 to December 31, 1969. Pore characteristics of six limestones were studied in relation to their absorption of two asphalt cements. Porosity and pore size distribution were determined by a mercury penetration porosimeter and asphalt absorption was determined by immersion and bulk-impregnated specific gravity methods. A special study was conducted to develop new, simple and more reproducible methods for bulk specific gravity determination. As a result, a new chemical indicator method was developed to determine the saturated surface-dry condition, and a glass mercury pycnometer was designed to determine coarse·and fine aggregates. Asphalt absorption history of one asphalt mixture on campus has been studied since September 1968. Chemical and/or radiation treatments of absorptive aggregates were conducted on four chemicals and two aggregates.

Analysis of Ultrasonic Techniques for the Characterization of Microfiltration Polymeric Membranes

The use of polymeric membranes is extremely important in several industries such as nuclear, biotechnology, chemical and pharmaceutical. In the nuclear area, for instance, systems based on membrane separation technologies are currently being used in the treatment of radioactive liquid effluent, and new technologies using membranes are being developed at a great rate. The knowledge of the physical characteristics of these membranes, such as, pore size and the pore size distribution, is very important to the membranes separation processes. Only after these characteristics are known is it possible to determine the type and to choose a particular membrane for a specific application. In this work, two ultrasonic non destructive techniques were used to determine the porosity of membranes: pulse echo and transmission. A 25 MHz immersion transducer was used. Ultrasonic signals were acquired, for both techniques, after the ultrasonic waves passed through a microfiltration polymeric membrane of pore size of 0.45 μm and thickness of 180 μm. After the emitted ultrasonic signal crossed the membrane, the received signal brought several information on the influence of the membrane porosity in the standard signal of the ultrasonic wave. The ultrasonic signals were acquired in the time domain and changed to the frequency domain by application of the Fourier Fast Transform (FFT), thus generating the material frequency spectrum. For the pulse echo technique, the ultrasonic spectrum frequency changed after the ultrasonic wave crossed the membrane. With the transmission technique there was only a displacement of the ultrasonic signal at the time domain.

Undersampled Critical Branching Processes on Small-World and Random Networks Fail to Reproduce the Statistics of Spike Avalanches

The power-law size distributions obtained experimentally for neuronal avalanches are an important evidence of criticality in the brain. This evidence is supported by the fact that a critical branching process exhibits the same exponent t~3=2. Models at criticality have been employed to mimic avalanche propagation and explain the statistics observed experimentally. However, a crucial aspect of neuronal recordings has been almost completely neglected in the models: undersampling. While in a typical multielectrode array hundreds of neurons are recorded, in the same area of neuronal tissue tens of thousands of neurons can be found. Here we investigate the consequences of undersampling in models with three different topologies (two-dimensional, small-world and random network) and three different dynamical regimes (subcritical, critical and supercritical). We found that undersampling modifies avalanche size distributions, extinguishing the power laws observed in critical systems. Distributions from subcritical systems are also modified, but the shape of the undersampled distributions is more similar to that of a fully sampled system. Undersampled supercritical systems can recover the general characteristics of the fully sampled version, provided that enough neurons are measured. Undersampling in two-dimensional and small-world networks leads to similar effects, while the random network is insensitive to sampling density due to the lack of a well-defined neighborhood. We conjecture that neuronal avalanches recorded from local field potentials avoid undersampling effects due to the nature of this signal, but the same does not hold for spike avalanches. We conclude that undersampled branching-process-like models in these topologies fail to reproduce the statistics of spike avalanches.

Matériaux mésoporeux fonctionnalisés pour l'extraction sélective des terres rares

Les matériaux mésoporeux à base de silice sont des plateformes polyvalentes qui offrent une réponse aux besoins de domaines variés comme l’environnement, la santé et les énergies. La fonctionnalisation avec des groupements organiques en fait des matériaux hybrides qu’il est aisé d’orienter vers une application spécifique. Ainsi, afin de fournir une alternative aux procédés industriels, dommageables pour l’environnement actuellement utilisés pour l’extraction et la purification des terres rares, à savoir l’extraction liquide-liquide (ELL) majoritairement, les silices mésoporeuses ont été sollicitées à titre d’adsorbant dans l’extraction sur phase solide. Cette dernière, en opposition à l’ELL, présente de nombreux avantages dont, la suppression des solvants organiques, le contrôle de la sélectivité envers et parmi le groupe des éléments de terres rares (ÉTR) à travers l’ancrage du ligand sur un support solide et la possibilité de réutiliser plusieurs fois l’adsorbant. Les ÉTR sont des métaux qui participent à la transition vers des technologies moins coûteuses en énergie, il est donc primordial de rendre leurs procédés d’extraction plus verts. Dans le cadre de ce travail, différents types de silices ordonnées mésoporeuses, MCM-41, SBA-15 et SBA-16, ont été synthétisées, fonctionnalisées avec un ligand approprié, et leurs comportements vis à vis de ces éléments, comparés. Ces matériaux ont de nombreux points communs mais certaines caractéristiques les différencient néanmoins : la taille et la géométrie des pores, la connexion entre les pores, l’épaisseur des parois, l’accessibilité aux pores ou encore la diffusion des liquides ou gaz dans la matrice. C’est pourquoi, le but de cette étude est d’élucider l’impact de ces diverses propriétés sur l’adsorption sélective des ÉTR en condition statique et dynamique.