Design Manual for Strengthening Single-Span Composite Bridges by Post-Tensioning Part 3, HR-238, 1985

The authors have post-tensioned and monitored two Iowa bridges and have field tested the post-tensioning of a composite bridge in Florida. In order to provide the practical post-tensioning distribution factors given in this manual, the authors developed a finite element model of a composite bridge and checked the model against a one-half scale laboratory bridge and two actual composite bridges, one of which had a 45 deg skew. Following a brief discussion of this background research, this manual explains the use of elastic, composite beam and bridge section properties, the distribution fractions for symmetrically post-tensioned exterior beams, and a method for computing the strength of a post-tensioned beam. Also included is a design example for a typical, 51.25-ft (15.62-m) span, four-beam composite bridge. Moments for Iowa Department of Transportation rating trucks, H 20 and HS 20 trucks, have been tabulated for design convenience and are included in the appendix.

Catalogue of Mesozoic radiolarian genera. Part 2: Jurassic-Cretaceous

The catalogue of Mesozoic radiolarian genera is a revision of all described genera with re-illustration of their type species. This project was organized under the auspices of the International Association of Radiolarian Paleontologists (Inter-Rad), and was carried out by the Mesozoic Working Group. This is the second of two contributions, this one devoted to the Jurassic-Cretaceous period. It contains 581 genera with re-illustration of their type species. This part shares 30 genera in common with the Triassic catalogue, most of which arose in the Carnian, Norian and Rhaetian. The sharp difference manifested between the Triassic fauna and the Jurassic-Cretaceous fauna is so evident that it justifies two independent catalogues. A comparable division between the Jurassic and Cretaceous could not be justified however, because of the similarity of the fauna, and by the greater number of genera crossing the Jurassic-Cretaceous boundary which is three times that for the Triassic-Jurassic boundary. A distinct characteristic of Jurassic-Cretaceous genera is the high number of nomina dubia (up to 131), contrary to the low number in the Triassic interval. This reflects, in part, the influence of Haeckelian taxonomy in earlier research on Jurassic-Cretaceous faunas prior to the application of SEM techniques. The Mesozoic Working Group has carefully reviewed and re-examined the taxonomy of all available genera, their family assignment and stratigraphic ranges. Following careful comparisons, 91 genera were declared as synonyms. The review has noted 26 homonyms which were duly notified to their corresponding authors, and were corrected previous to the publication of this catalogue. In spite of this effort, unfortunately nine homonyms still remain. Two invalid nominal genera, and two nomina nuda are also reported. The systematic revisions have validated 341 genera for the Jurassic-Cretaceous interval. At the end of this catalogue 24 additional are resented as support for those genera having a poor photographs p original illustration of the type species.

Thermoset Composite Concrete Reinforcement, HR-325, Part 1, 1992

The feasibility of substituting fibercomposite (FC) (thermoset) pavement dowels for steel pavement dowels was investigated in this research project. Load transfer capacity, flexural capacity, and material properties were examined. The objectives of Part 1 of this final report included the shear behavior and strength deformations of FC dowel bars without aging. Part 2 will contain the aging effects. This model included the effects of modulus of elasticity for the pavement dowel and concrete, dowel diameter, subgrade stiffness, and concrete compressive strength. An experimental investigation was carried out to establish the modulus of dowel support which is an important parameter for the analysis of dowels. The experimental investigation included measured deflections, observed behavioral characteristics, and failure mode observations. An extensive study was performed on various shear testing procedures. A modified Iosipescu shear method was selected for the test procedure. Also, a special test frame was designed and fabricated for this procedure. The experimental values of modulus of support for shear and FC dowels were used for arriving at the critical stresses and deflections for the theoretical model developed. Different theoretical methods based on analyses suggested by Timoshenko, Friberg, Bradbury, and Westergaard were studied and a comprehensive theoretical model was developed. The fibercomposite dowels were found to provide strengths and behavioral characteristics that appear promising as a potential substitute for steel dowels.

Implementing statistical learning methods through Bayesian networks. Part 1: a guide to Bayesian parameter estimation using forensic science data

As a thorough aggregation of probability and graph theory, Bayesian networks currently enjoy widespread interest as a means for studying factors that affect the coherent evaluation of scientific evidence in forensic science. Paper I of this series of papers intends to contribute to the discussion of Bayesian networks as a framework that is helpful for both illustrating and implementing statistical procedures that are commonly employed for the study of uncertainties (e.g. the estimation of unknown quantities). While the respective statistical procedures are widely described in literature, the primary aim of this paper is to offer an essentially non-technical introduction on how interested readers may use these analytical approaches - with the help of Bayesian networks - for processing their own forensic science data. Attention is mainly drawn to the structure and underlying rationale of a series of basic and context-independent network fragments that users may incorporate as building blocs while constructing larger inference models. As an example of how this may be done, the proposed concepts will be used in a second paper (Part II) for specifying graphical probability networks whose purpose is to assist forensic scientists in the evaluation of scientific evidence encountered in the context of forensic document examination (i.e. results of the analysis of black toners present on printed or copied documents).

Le temps partagé dans la jouissance de la propriété par étages : étude de la copropriété spatio-temporelle sur une part d'étage

Introduction : Depuis plusieurs années, la pratique a développé une nouvelle forme d'utilisation de la propriété immobilière : le time-sharing, que l'on appelle aussi couramment propriété en temps partagé ou multipropriété. Son objectif est de permettre à plusieurs personnes de bénéficier du même logement de vacances en prévoyant une répartition temporelle de leur usage. Actuellement, il n'existe dans le système juridique suisse aucune disposition légale qui traite expressément du time-sharing, mais ce concept peut être valablement établi sur la base du droit en vigueur en ayant recours à différentes constructions. En effet, le droit contractuel, le droit des sociétés et les droits réels sont autant de moyens utilisés par la pratique pour atteindre le but fixé. Le choix entre ces diverses alternatives n'est toutefois pas anodin, car il détermine de manière directe la position juridique du time-sharer vis-à-vis des tiers et des personnes qui font partie de la même structure que lui. Le système du time-sharing a suscité un véritable engouement auprès des consommateurs, mais il a également donné lieu à de nombreux abus dont la presse s'est faite l'écho. Pour ces raisons, le législateur envisage aujourd'hui d'introduire des dispositions légales protectrices permettant de délimiter précisément les droits et obligations dont le time-sharer acquiert la titularité. Cette intervention législative ne consiste toutefois pas en une réglementation du time-sharing, mais uniquement en l'élaboration de normes générales qui doivent s'appliquer lors de la conclusion du contrat d'acquisition et qui se veulent compatibles avec les différentes constructions juridiques possibles. Nous avons choisi, pour la présente étude, d'examiner les possibilités qu'offrent les droits réels pour établir le partage de la jouissance d'un appartement et d'analyser la construction qui assure au consommateur la position la plus stable : celle de copropriétaire d'une part de propriété par étages. Les caractéristiques propres au time-sharing qui nous intéresse sont ainsi les suivantes : 1) Le time-sharer est un véritable propriétaire immobilier. Le droit de propriété assure une position forte à son titulaire qui bénéficie alors de tous les attributs et toutes les garanties de ce droit absolu. Mais le fait que plusieurs personnes acquièrent le même objet, nous met en présence du concept de propriété collective qu'il faut analyser afin d'expliquer la construction juridique du time-sharing en droits réels. 2) L'appartement reste toujours le même. L'objectif principal du consommateur est d'acquérir un droit de propriété sur un logement qu'il a lui-même choisi. Nous excluons ainsi les sociétés qui mettent à disposition de leurs membres un choix d'appartements que ce soit contre le versement d'une somme d'argent, par le biais d'un système d'acquisition de points-vacances, ou proportionnellement à l'investissement dans le capital social et le parc immobilier de la société. En outre, bien qu'il soit loisible à tout propriétaire d'entrer en relation avec une société d'échange afin de bénéficier d'un autre appartement, nous n'examinerons pas les rapports juridiques ainsi créés, car ils relèvent du droit contractuel et du droit des sociétés et non des droits réels. 3) L'immeuble est situé en Suisse et il est organisé en propriété par étages avant que les différents appartements qui le constituent ne soient vendus. Malgré le succès connu par le time-sharing hors de nos frontières, nous avons décidé de nous intéresser uniquement au statut réel du time-sharing en droit suisse et non aux divers problèmes qui peuvent surgir en droit international privé face aux contrats passés sous l'empire d'un droit étranger. En outre, comme nous le verrons, la structure de la propriété par étages se révèle être parfaitement adaptée au time-sharing en offrant une organisation élaborée et une communauté bénéficiant de la quasi-personnalité juridique. 4) Il n'y a aucun lien préexistant entre les différents acquéreurs et il n'est, par conséquent, pas nécessaire que l'acquisition de l'appartement se fasse simultanément et de manière collective. Dans la plupart des cas, les acquisitions seront échelonnées dans le temps et les personnes entreront en contact uniquement par le biais de leur logement commun. Le système permet donc une grande indépendance entre les différents membres du time-sharing, autant lors de l'achat que de la revente du droit de jouissance. 5) L'appartement étant vendu à de nombreuses personnes, il est nécessaire de fixer des périodes cycliques de jouissance. Celles-ci sont l'élément essentiel du time-sharing et déterminent le prix de vente par leur durée et par leur situation annuelle en haute saison ou en concordance avec les vacances scolaires. Toutefois, bien d'autres éléments nécessitent d'être règlés au niveau de l'organisation interne pour établir avec précision les droits et obligations de chacun. Le plan de notre étude comporte quatre parties principales qui portent respectivement sur la théorie de la propriété collective, sur les différentes constructions envisageables dans le domaine des droits réels, sur l'organisation de la copropriété fondant le time-sharing et sur l'examen des projets de révisions législatives à la lumière de la copropriété.

Anatomical distribution of areas of preserved cartilage in advanced femorotibial osteoarthritis using CT arthrography (Part 1).

OBJECTIVE: To determine subregions of normal and abnormal cartilage in advanced stages of femorotibial osteoarthritis (OA) by mapping the entire femorotibial joint in a cohort of pre-total knee replacement (TKR) OA knees. DESIGN: We defined an areal subdivision of the femorotibial articular cartilage surface on CT arthrography (CTA), allowing the division of the femorotibial articular surface into multiple (up to n = 204 per knee) subregions and the comparison of the same areas between different knees. Two readers independently classified each cartilage area as normal, abnormal or non-assessable in 41 consecutive pre-TKR OA knees. RESULTS: A total of 6447 cartilage areas (from 41 knees) were considered assessable by both readers. The average proportion of preserved cartilage was lower in the medial femorotibial joint than in the lateral femorotibial joint for both readers (32.0/69.8% and 33.9/68.5% (medial/lateral) for reader 1 and 2 respectively, all P < 0.001). High frequencies of normal cartilage were observed at the posterior aspect of the medial condyle (up to 89%), and the anterior aspect of the lateral femorotibial compartment (up to 100%). The posterior aspect of the medial condyle was the area that most frequently exhibited preserved cartilage in the medial femorotibial joint, contrasting with the high frequency of cartilage lesions in the rest of that compartment. CONCLUSIONS: Cartilage at the posterior aspect of the medial condyle, and at the anterior aspect of the lateral femorotibial compartment, may be frequently preserved in advanced grades of OA.

Structural investigations into the interaction of hemoglobin and part structures with bacterial endotoxins.

An understanding of details of the interaction mechanisms of bacterial endotoxins (lipopolysaccharide, LPS) with the oxygen transport protein hemoglobin is still lacking, despite its high biological relevance. Here, a biophysical investigation into the endotoxin:hemoglobin interaction is presented which comprises the use of various rough mutant LPS as well as free lipid A; in addition to the complete hemoglobin molecule from fetal sheep extract, also the partial structure alpha-chain and the heme-free sample are studied. The investigations comprise the determination of the gel-to-liquid crystalline phase behaviour of the acyl chains of LPS, the ultrastructure (type of aggregate structure and morphology) of the endotoxins, and the incorporation of the hemoglobins into artificial immune cell membranes and into LPS. Our data suggest a model for the interaction between Hb and LPS in which hemoglobins do not react strongly with the hydrophilic or with the hydrophobic moiety of LPS, but with the complete endotoxin aggregate. Hb is able to incorporate into LPS with the longitudinal direction parallel to the lipid A double-layer. Although this does not lead to a strong disturbance of the LPS acyl chain packing, the change of the curvature leads to a slightly conical molecular shape with a change of the three-dimensional arrangement from unilamellar into cubic LPS aggregates. Our previous results show that cubic LPS structures exhibit strong endotoxic activity. The property of Hb on the physical state of LPS described here may explain the observation of an increase in LPS-mediating endotoxicity due to the action of Hb.

Psychometric evaluation of the IWQOL-Lite (Spanish version) when applied to a sample of obese patients awaiting bariatric surgery

Background Obesity may have an impact on key aspects of health-related quality of life (HRQOL). In this context, the Impact of Weight Quality of Life (IWQOL) questionnaire was the first scale designed to assess HRQOL. The aim of the present study was twofold: to assess HRQOL in a sample of Spanish patients awaiting bariatric surgery and to determine the psychometric properties of the IWQOL-Lite and its sensitivity to detect differences in HRQOL across groups. Methods Participants were 109 obese adult patients (BMI¿ 35 kg/m2) from Barcelona, to whom the following measurement instruments were applied: IWQOL-Lite, Depression Anxiety Stress Scales, Brief Symptom Inventory, and self-perception items. Results Descriptive data regarding the IWQOL-Lite scores obtained by these patients are reported. Principal components analysis revealed a five-factor model accounting for 72.05% of the total variance, with factor loadings being adequate for all items. Corrected itemtotal correlations were acceptable for all items. Cronbach"s alpha coefficients were excellent both for the subscales (0.880.93) and the total scale (0.95). The relationship between the IWQOLLite and other variables supports the construct validity of the scale. Finally, sensitivity analysis revealed large effect sizes when comparing scores obtained by extreme BMI groups. Conclusions This is the first study to report the application of the IWQOL-Lite to a sample of Spanish patients awaiting bariatric surgery and to confirm that the Spanish version of the instrument has adequate psychometric properties.

Factors affecting visual analysis in single-case designs

Visual inspection remains the most frequently applied method for detecting treatment effects in single-case designs. The advantages and limitations of visual inference are here discussed in relation to other procedures for assessing intervention effectiveness. The first part of the paper reviews previous research on visual analysis, paying special attention to the validation of visual analysts" decisions, inter-judge agreement, and false alarm and omission rates. The most relevant factors affecting visual inspection (i.e., effect size, autocorrelation, data variability, and analysts" expertise) are highlighted and incorporated into an empirical simulation study with the aim of providing further evidence about the reliability of visual analysis. Our results concur with previous studies that have reported the relationship between serial dependence and increased Type I rates. Participants with greater experience appeared to be more conservative and used more consistent criteria when assessing graphed data. Nonetheless, the decisions made by both professionals and students did not match sufficiently the simulated data features, and we also found low intra-judge agreement, thus suggesting that visual inspection should be complemented by other methods when assessing treatment effectiveness.

¿Cómo los académicos españoles se enfrentan con el cambio? respuesta desde una investigación de historias de vida profesionales

[spa] Este documento forma parte de la investigación, Los efectos de los cambios sociales en el trabajo y la vida profesional de los docentes universitarios, parcialmente financiado por el Ministerio de Ciencia e Innovación (SEJ2006-01876), en el que hemos explorado los cambios en la legislación, la organización, los contextos de la investigación y la docencia, etc., en los últimos treinta años. El principal objetivo de este documento es profundizar en nuestra comprensión sobre el impacto del cambio económico, social, cultural, tecnológico y laboral que están experimentando las universidades españolas en la vida y la identidad profesional del personal docente e investigador, teniendo en cuenta el contexto nacional y europeo. Este trabajo recoge parte de los resultados obtenidos en el proyecto, siendo su principal objetivo contribuir a mejorar el conocimiento basado en la investigación sobre el saber profesional y la experiencia laboral en las universidades españolas, y en consecuencia, favorecer nuestra comprensión sobre cómo los académicos se están enfrentando con los cambios actuales.

Comparison of Creep and Resilient Modulus Laboratory Results with Field Cores, HR-311, Part 3, 1993

This is Part 3 of a study of creep and resilient modulus testing of hot mix asphalt concrete. The creep and resilient modulus testing in Part 1 showed the improved load carrying characteristics of crushed particles. Cores from pavements drilled in Part 2 exhibited a poor correlation with rutting and creep/resilient modulus on pavement with a range of rut depths. The objective of Part 3 was to determine the relationship of creep and resilient modulus for 1) Marshall specimens from laboratory mixing for mix design; 2) Marshall specimens from construction plant mixing; and 3) cores drilled from the hot mixed asphalt pavement. The creep and resilient modulus data from these three sources exhibited substantial variations. No meaningful correlations of the results from these three sources were obtained.

Nonlinear Pile Behavior in Integral Abutment Bridges, HR-227, Part 1, 1982

The highway departments of all fifty states were contacted to find the extent of application of integral abutment bridges, to survey the different guidelines used for analysis and design of integral abutment bridges, and to assess the performance of such bridges through the years. The variation in design assumptions and length limitations among the various states in their approach to the use of integral abutments is discussed. The problems associated with lateral displacements at the abutment, and the solutions developed by the different states for most of the ill effects of abutment movements are summarized in the report. An algorithm based on a state-of-the-art nonlinear finite element procedure was developed and used to study piling stresses and pile-soil interaction in integral abutment bridges. The finite element idealization consists of beam-column elements with geometric and material nonlinearities for the pile and nonlinear springs for the soil. An idealized soil model (modified Ramberg-Osgood model) was introduced in this investigation to obtain the tangent stiffness of the nonlinear spring elements. Several numerical examples are presented in order to establish the reliability of the finite element model and the computer software developed. Three problems with analytical solutions were first solved and compared with theoretical solutions. A 40 ft H pile (HP 10 X 42) in six typical Iowa soils was then analyzed by first applying a horizontal displacement (to simulate bridge motion) and no rotation at the top and then applying a vertical load V incrementally until failure occurred. Based on the numerical results, the failure mechanisms were generalized to be of two types: (a) lateral type failure and (b) vertical type failure. It appears that most piles in Iowa soils (sand, soft clay and stiff clay) failed when the applied vertical load reached the ultimate soil frictional resistance (vertical type failure). In very stiff clays, however, the lateral type failure occurs before vertical type failure because the soil is sufficiently stiff to force a plastic hinge to form in the pile as the specified lateral displacement is applied. Preliminary results from this investigation showed that the vertical load-carrying capacity of H piles is not significantly affected by lateral displacements of 2 inches in soft clay, stiff clay, loose sand, medium sand and dense sand. However, in very stiff clay (average blow count of 50 from standard penetration tests), it was found that the vertical load carrying capacity of the H pile is reduced by about 50 percent for 2 inches of lateral displacement and by about 20 percent for lateral displacement of 1 inch. On the basis of the preliminary results of this investigation, the 265-feet length limitation in Iowa for integral abutment concrete bridges appears to be very conservative.