955 resultados para Osmotic stresses
Resumo:
Nesse trabalho foram realizados experimentos para determinar as tensões residuais introduzidas no Aço A36, que é uma liga de baixo carbono e que é muito utilizado em vários setores da produção industrial, quando esta é submetida à soldagem do tipo MIG (Metal Gas Inert). A escolha desse tipo de soldagem foi para manter constantes os parâmetros que pudessem influenciar nos resultados. Nessa análise foi verificada a distribuição das tensões residuais na zona termicamente afetada, a distribuição da tensão em relação a profundidade. Para isso usamos uma remoção eletrolítica e um corte transversal pelo processo de eletroerosão. Nesse trabalho foi usado o método do sen2, devido a sua facilidade para a análise dos dados do Programa PSD. O resultado das mediadas realizadas na região do cordão de solda, zona termicamente afetada (ZTA) e metal base próxima da ZTA, mostrou uma variação da distribuição da tensão em relação à profundidade do material e na distância do ponto de soldagem. No ponto de soldagem um aumento da tensão em relação à profundidade do material. Os fatores que influenciaram na introdução dessas tensões no processo de soldagem, foram causados pelo gradiente de temperatura, pelo resfriamento heterogêneo do material e também pelo resfriamento rápido da superfície
Resumo:
The Pacoima area is located on an isolated hill in the northeast section of the San Fernando, the northeast portion of the Pacoima Quadrangle, Los Angeles County, California. Within it are exposed more than 2300 feet of Tertiary rocks, which comprise three units of Middle Miocene (?) age, and approximately 950 feet of Jurassic (?) granite basement. The formations are characterized by their mode of occurrence, marine and terrestial origin, diverse lithology, and structural features.
The basement complex is composed of intrusive granite, small masses of granodiorite and a granodiorite gneiss with the development of schistosity in sections. During the long period of erosion of the metamorphics, the granitic rocks were exposed and may have provided clastic constituents for the overlying formations.
As a result of rapid sedimentation in a transitional environment, the Middle Miocene Twin Peaks formation was laid down unconformably on the granite. This formation is essentially a large thinning bed of gray to buff pebble and cobble conglomerate grading to coarse yellow sandstone. The contact of conglomerate and granite is characterized by its faulted and depositional nature.
Beds of extrusive andesite, basalt porphyry, compact vesicular amygdaloidal basalts, andesite breccia, interbedded feldspathic sands and clays of terrestial origin, and mudflow breccia comprise the Pacoima formation which overlies the Twin Peaks formation unconformably. A transgressing shallow sea accompanied settling of the region and initiated deposition of fine clastic sediments.
The marine Topanga (?) formation is composed of brown to gray coarse sandstone grading into interbedded buff sandstones and gray shales. Intrusions of rhyolitedacite and ash beds mark continued but sporatic volcanism during this period.
The area mapped represents an arch in the Tertiary sediments. Forces that produced the uplift of the granite structural high created stresses that were relieved by jointing and faulting. Vertical and horizontal movement along these faults has displaced beds, offset contacts and complicated their structure. Uplift and erosion have exposed the present sequence of beds which dip gently to the northeast. The isolated hill is believed to be in an early stage of maturity.
Resumo:
Para reabilitar a ausência de um elemento dentário posterior, as próteses parciais fixas (PPF) com retentores intracoronários são uma alternativa aos implantes osseointegrados. O objetivo deste estudo foi avaliar a distribuição de tensões nessas próteses com três combinações de materiais: cerâmica de zircônia parcialmente estabilizada por ítria (ZPEI) revestida por cerâmica de fluorapatita (α), cerâmica de dissilicato de lítio (β) ou compósito fibrorreforçado (γ). Na composição α, foram analisadas a presença ou ausência da cerâmica de revestimento na parede cervical das caixas proximais e três variações na área total da seção transversal dos conectores (4 mm de largura x 3,2, 4,2 ou 5,2 mm de altura). Em 8 modelos bidimensionais de elementos finitos, uma carga vertical de 500 N foi aplicada na fossa central do pôntico e as tensões principais máximas (tração) e mínimas (compressão) foram apontadas em MPa. Inicialmente foram avaliados os 6 modelos com PPF de ZPEI e suas variações. Os maiores valores das tensões de tração foram encontrados no terço cervical dos conectores. Quando presente nestas regiões, a cerâmica de revestimento recebeu tensões acima do limite de sua resistência à flexão. Na comparação entre os modelos sem cerâmica de revestimento na parede cervical das caixas proximais, mesmo aquele com conectores de 3,2 x 4 mm, cuja infraestrutura apresentava 2,5 x 3 mm, poderia ser recomendado para uso clínico. Altos valores de tensões de compressão foram registrados entre o terço oclusal e médio dos conectores, correspondente à união entre as cerâmicas, o que poderia ocasionar, devido à flexão, falhas adesivas. Posteriormente, o modelo de ZPEI com a cerâmica de fluorapatita ausente da parede cervical das caixas proximais e área total dos conectores de 4,2 x 4 mm foi comparado aos dois outros materiais com conectores de mesma área. Na PPF de dissilicato de lítio, os valores representaram uma provável violação do limite de sua resistência à flexão. A PPF de compósito fibrorreforçado apresentou tensões bem abaixo do limite de resistência à flexão de sua infraestrutura, mas, como no modelo de ZPEI, tensões compressivas se concentraram com alto valor entre o terço oclusal e médio dos conectores, local de união entre a resina composta e a infraestrutura de fibras. Os resultados mostraram que a cerâmica de dissilicato de lítio e a presença da cerâmica de fluorapatita na parede cervical das caixas proximais deveriam ser contraindicadas para a condição proposta. Parece viável uma área de conectores na infraestrutura de ZPEI com no mínimo 2,5 x 3 mm. A PPF de compósito fibrorreforçado apresenta resistência estrutural para a situação estudada, mas, como também aquelas compostas de ZPEI, aparenta ter como pontos fracos a adesão entre a infraestrutura e o material de cobertura e a própria resistência deste último.
Resumo:
In four chapters various aspects of earthquake source are studied.
Chapter I
Surface displacements that followed the Parkfield, 1966, earthquakes were measured for two years with six small-scale geodetic networks straddling the fault trace. The logarithmic rate and the periodic nature of the creep displacement recorded on a strain meter made it possible to predict creep episodes on the San Andreas fault. Some individual earthquakes were related directly to surface displacement, while in general, slow creep and aftershock activity were found to occur independently. The Parkfield earthquake is interpreted as a buried dislocation.
Chapter II
The source parameters of earthquakes between magnitude 1 and 6 were studied using field observations, fault plane solutions, and surface wave and S-wave spectral analysis. The seismic moment, MO, was found to be related to local magnitude, ML, by log MO = 1.7 ML + 15.1. The source length vs magnitude relation for the San Andreas system found to be: ML = 1.9 log L - 6.7. The surface wave envelope parameter AR gives the moment according to log MO = log AR300 + 30.1, and the stress drop, τ, was found to be related to the magnitude by τ = 0.54 M - 2.58. The relation between surface wave magnitude MS and ML is proposed to be MS = 1.7 ML - 4.1. It is proposed to estimate the relative stress level (and possibly the strength) of a source-region by the amplitude ratio of high-frequency to low-frequency waves. An apparent stress map for Southern California is presented.
Chapter III
Seismic triggering and seismic shaking are proposed as two closely related mechanisms of strain release which explain observations of the character of the P wave generated by the Alaskan earthquake of 1964, and distant fault slippage observed after the Borrego Mountain, California earthquake of 1968. The Alaska, 1964, earthquake is shown to be adequately described as a series of individual rupture events. The first of these events had a body wave magnitude of 6.6 and is considered to have initiated or triggered the whole sequence. The propagation velocity of the disturbance is estimated to be 3.5 km/sec. On the basis of circumstantial evidence it is proposed that the Borrego Mountain, 1968, earthquake caused release of tectonic strain along three active faults at distances of 45 to 75 km from the epicenter. It is suggested that this mechanism of strain release is best described as "seismic shaking."
Chapter IV
The changes of apparent stress with depth are studied in the South American deep seismic zone. For shallow earthquakes the apparent stress is 20 bars on the average, the same as for earthquakes in the Aleutians and on Oceanic Ridges. At depths between 50 and 150 km the apparent stresses are relatively high, approximately 380 bars, and around 600 km depth they are again near 20 bars. The seismic efficiency is estimated to be 0.1. This suggests that the true stress is obtained by multiplying the apparent stress by ten. The variation of apparent stress with depth is explained in terms of the hypothesis of ocean floor consumption.
Resumo:
The osmotic pressure of the perivitelline fluid and the yolk of trout (Salmo trutta) eggs were measured separately by the Drucker-Schrein method. The permeability of the egg membrane and the variations in the osmotic pressure of the eggs when placed in salt solutions were also investigated.
Resumo:
The span of the bridge was assumed as 100 feet. The type of bridge used is the timber Howe Truss. The height of truss was taken as 20 feet between center lines of top and bottom chords. The width was taken as 18 feet center to center of trusses. The truss was divided up into five panels 20 feet long.
It was designed according to the "General Specifications for Steel Highway Bridges" by Ketchum. For the live load for the floor and its supports, a load of 80 pounds per square foot of total floor surface or a 15 ton traction engine with axles 10 feet centers and 6 feet gage, two thirds of load to be carried by rear axles.
For the truss a load of 75 pounds per square foot of floor surface.
For the wind load the bottom lateral bracing is to be designed to resist a lateral wind load of 300 pounds per foot of span; 150 pounds of this to be treated as a moving load.
The top lateral bracing is to be designed to resist a lateral wind force of 150 pounds per foot of span.
The timber to be used in the bridge is to be Douglas fir.
The unit stresses used for timber are those of the American Railway Engineering Association.
Resumo:
It was shown, with the aid of osmotic inhibition of germination, that the action of the far-red-absorbing form of phytochrome (Pf) in promoting germination can be completed even if the seed is held under conditions where germination is not possible. An effect of the continuing action of Pf beyond the point of complete germination promotion was demonstrated by enhancement of germination rate after removal of the osmotically active solute.
Previous reports that the rate of growth in water of seeds freed from the expansion-restricting endosperm is independent of the state of phytochrome were confirmed. However, a marked, phytochrome-mediated enhancement of the growth potential of such seeds was demonstrated through restricting water uptake by incubation in an osmoticum.
An experimental system, utilizing the appearance of a geotropic curvature in the radicle of the excised axial portion of the seed, was developed for more detailed studies of the phytochrome-enhanced growth potential. It was possible to demonstrate the light effect in water as well as in osmotica; this apparently is not possible with de-endospermed entire seeds. As in intact seeds, the effect of the continuing action of Pf is to enhance the rate of the response. Secretion of a chemical inhibitor of growth by the endosperm as a possible mechanism of induction of light sensitivity has been ruled out.
The phytochrome-dependent rate of appearance of geotropic curvature in osmotica is paralleled in time by a similar dependence of the rate of early extension growth of the embryonic axis. Only the first small increment of growth is a differentially responsive to red (R) and far-red (F); the rate of later increase in length is independent of the light regime.
It was shown that the high concentrations of gibberellic acid required for germination promotion in the intact seed are due at least in part to a diffusion barrier in the endosperm, and that the occasional reports in the literature of the ineffectiveness of kinetin are probably due to the same phenomenon. It was shown that gibberellin, like red light, enhances the growth potential of the axis, but kinetin does not. The difference in rates of response obtained after R-irradiation or gibberellin treatment, together with other results reported in the literature, strongly suggests that gibberellic acid and red light promote germination by different means. The idea that kinetin promotes germination by yet another mechanism, probably operating in the cotyledons, was supported through two different experimental approaches.
The phenomenon of temperature-dependent dark germination was examined in detail, using a wide range of both temperatures and incubation times. With the aid of the half-seed system, it was demonstrated that the promotive effect of low temperature on germination could not be due to a low optimum temperature for early growth of the radicle, since the rate of that process increased with increasing temperature, up to the highest temperature used.
It was shown that phytochrome does not function at high temperatures. This fact is of considerable importance in interpreting the phenomenon of thermodormancy, since in the literature only a small part of the effect of high temperature has been ascribed to an effect on phytochrome, and at that, only to an acceleration of dark reversion of Pf to the red-absorbing form of phytochrome (Pr). Partial denaturation of phytochrome may also make some contribution.
It was shown that the germination-promoting effect of low temperature depends on the presence of Pf, and concluded that low temperatures act by delaying or preventing transformation of Pf. Support for the assumption that Pf, not Pr, is the active form of phytochrome in lettuce seeds was drawn from the same evidence.
Attempts to stimulate germination by repeated irradiation with F over relatively prolonged incubation times resulted in failure, as have similar attempts reported in the literature. However, an enhancement of growth potential in the half-seed system by the maintenance of a small amount of Pf over long periods at ordinary temperatures by repeated irradiation with F was demonstrated.
It was observed that cold storage of the dry seed prevents or delays loss of dark dormancy during post-harvest storage. No change in the response of the half-seed in osmoticum to R and F was observed in seeds that has lost dark dormancy; that is, no internal change took place to measurably increase the growth potential of the embryonic axis. This suggests that the endosperm is the seat of changes responsible for after-ripening of photoblastic lettuce seed.
Resumo:
Part I
The slow, viscous flow past a thin screen is analyzed based on Stokes equations. The problem is reduced to an associated electric potential problem as introduced by Roscoe. Alternatively, the problem is formulated in terms of a Stokeslet distribution, which turns out to be equivalent to the first approach.
Special interest is directed towards the solution of the Stokes flow past a circular annulus. A "Stokeslet" formulation is used in this analysis. The problem is finally reduced to solving a Fredholm integral equation of the second kind. Numerical data for the drag coefficient and the mean velocity through the hole of the annulus are obtained.
Stokes flow past a circular screen with numerous holes is also attempted by assuming a set of approximate boundary conditions. An "electric potential" formulation is used, and the problem is also reduced to solving a Fredholm integral equation of the second kind. Drag coefficient and mean velocity through the screen are computed.
Part II
The purpose of this investigation is to formulate correctly a set of boundary conditions to be prescribed at the interface between a viscous flow region and a porous medium so that the problem of a viscous flow past a porous body can be solved.
General macroscopic equations of motion for flow through porous media are first derived by averaging Stokes equations over a volume element of the medium. These equations, including viscous stresses for the description, are more general than Darcy's law. They reduce to Darcy's law when the Darcy number becomes extremely small.
The interface boundary conditions of the first kind are then formulated with respect to the general macroscopic equations applied within the porous region. An application of such equations and boundary conditions to a Poiseuille shear flow problem demonstrates that there usually exists a thin interface layer immediately inside the porous medium in which the tangential velocity varies exponentially and Darcy's law does not apply.
With Darcy's law assumed within the porous region, interface boundary conditions of the second kind are established which relate the flow variables across the interface layer. The primary feature is a jump condition on the tangential velocity, which is found to be directly proportional to the normal gradient of the tangential velocity immediately outside the porous medium. This is in agreement with the experimental results of Beavers, et al.
The derived boundary conditions are applied in the solutions of two other problems: (1) Viscous flow between a rotating solid cylinder and a stationary porous cylinder, and (2) Stokes flow past a porous sphere.
Resumo:
Alterações nutricionais, hormonais e ambientais nos períodos críticos do desenvolvimento como a gestação e/ou lactação podem influenciar a estrutura e a fisiologia de órgãos e tecidos, predispondo ao aparecimento de doenças na vida adulta. Esse fenômeno é conhecido como programação metabólica. O fumo materno na gestação/lactação tem sido associado ao sobrepeso/obesidade na infância e na vida adulta em ambos os sexos. Porém, estudos evidenciam diferenças entre os gêneros em resposta a exposição à nicotina. Já foi demonstrado que muitas mulheres param de fumar na gestação, mas a maioria destas volta a fumar na lactação. Anteriormente, mostramos que machos adultos cujas mães foram expostas à nicotina na lactação, desenvolveram obesidade central, hiperleptinemia e hipotireoidismo. Como a nicotina afeta a função adrenal e como catecolaminas e glicocorticóides têm efeitos bem conhecidos sobre o tecido adiposo, avaliamos a função da medula adrenal e o conteúdo de leptina no tecido adiposo e músculo de machos e fêmeas cujas mães foram expostas à nicotina na lactação. Dois dias pós-parto, implantamos minibombas osmóticas nas ratas lactantes dividas em: NIC infusão de nicotina (6mg/Kg/dia s.c.) por 14 dias, e C infusão de salina pelo mesmo período. Estas lactantes foram divididas de acordo com o sexo das proles. O sacrifício das proles de ambos os sexos ocorreu aos 15 (fim da exposição à nicotina) e 180 dias de vida. Aos 15 dias, os machos da prole NIC apresentaram aumento de MGV absoluta e relativa ao peso corporal (+72% e +73% respectivamente), hiperleptinemia (+35%), hipercorticosteronemia (+67%), maior peso adrenal (+39%), conteúdo de catecolaminas totais (absoluto: +69% e relativo: +41%), embora diminuição da enzima TH (-33%). Quando adultos, os machos programados exibiram maior massa corporal (+10%), MGV absoluta (+47%) e relativa (+33%), além de hiperleptinemia (+41%) e maior conteúdo de leptina no TAV (+23%). Esses animais também apresentaram hipercorticosteronemia (+77%), maior conteúdo de catecolaminas totais absoluto e relativo (+79% e +89% respectivamente) e de TH (+38%) embora tenham menor secreção de catecolaminas in vitro estimulada por cafeína (-19%) e maior expressão do ADRB3 no TAV (+59%). Em relação as fêmeas da prole NIC aos 15 dias de vida, estas apresentaram menor massa corporal (-6%) e hiperleptinemia (+41%) embora sem alteração da MGV. Aos 180 dias, as fêmeas da prole NIC apresentaram menor conteúdo de leptina no TAS (-46%) e maior conteúdo de leptina no músculo solear (+22%) e diminuição da expressão do ADRB3 no TAV (-39%). Concluímos que a nicotina materna afeta ambos, medula adrenal e tecido adiposo de forma gênero dependente, tanto em curto prazo (quando a nicotina está presente no leite materno), quanto em longo prazo (repercussões na vida adulta). De forma geral, as fêmeas da prole NIC apresentam alterações mais discretas do que os machos em ambos os períodos estudados.
Resumo:
The Amazon river, located in northernBrazil, discharges between 80,000 and 250,000 m3s-1 of water onto the adjacent shelf, creating a plume of brackish water that extends hundreds of kilometers away from the river mouth. This river also carries a large amount of fine sediments to the ocean where fluid mud has been found in the topset and upper foreset layers of the subaqueous delta formed on the mid-shelf. One of the main goals of this dissertation is to describe how turbulence and suspended sediment concentration vary along the Northern Channel of the Amazon river. Water column measurements were carried out in October 2008 at six anchor stations (P1, P3, P5, P6, P8 e P9) located seaward of the river mouth; P1 and P9 were 125 km apart. Each station was occupied during 13 hours during which current speed and direction were continuously sampled with a 600 kHz Teledyne-RDI ADCP; hourly profiles of temperature, salinity, turbidity and depth were also obtained. Water samples were collected for determination of Suspended Particulate Matter (SPM) concentration and calibration of the turbidity sensor. Current speed reached values above 1.5 m s1 in the along-channel direction (NE-SW); a remarkable ebb-flood asymmetry was observed and flows were strongly ebb-dominated. Throughout the water column, SPM concentration at stations P1 and P3 varied between 100 and 300 mg L1 in association with the presence of freshwater. In contrast, a strong salinity gradient was observed between stations P6 and P9, coinciding with the occurrence of concentrations of SPM above 10 g L-1 (fluid mud). At stations P3, P5 and P6, interface between freshwater from the Amazon river and salt water from the continental shelf, shear stresses wereestimated through four diferents methods: Reynolds, Turbulent Kinetic Energy (TKE), modified TKE and Quadratic Law; in the nearbed region (3 mab) the computed values varied between 0 and 3 Pa. At the three stations (P3, P5 and P6) the lowest and the highest shear stress values were obtained through, respectively, the Reynolds and the TKE methods. Over the whole water column turbulence intensity was estimated through the standard deviation of the turbulent component of the along-channel current velocity (root-mean square of u); from these values, it was estimated the turbulent dissipation of energy (G), whose values at 3 mab varied between zero and 20 s1.