Numerical modeling of interactions between a macro-crack and a cluster of micro-defects

The interactions between a macro-crack and a cluster of micro-defects are studied numerically by using a series of special finite elements each containing a defect. These special finite elements, which contain defects such as holes, cracks, and inhomogeneities, are developed based on the hybrid displacement, complex potential and conformal mapping techniques. These hybrid-type elements can be used together with the conventional finite elements without any difficulty. Thus, simple finite element models can be devised to study the interactions between a macro-crack and a cluster of micro-defects. In this paper, the mathematical and finite element modeling procedures for the study of the above-mentioned problems are presented.

Micro-porous nickel produced by powder metallurgy

Micro-porous nickel (Ni) with an open cell structure was fabricated by a special powder metallurgical process, which includes the adding of a space-holding material. The average pore size of the micro-porous Ni samples approximated 30 μm and 150 μm, and the porosity ranged from 60 % to 80 %. The porous characteristics of the Ni samples were observed using scanning electron microscopy (SEM) and the mechanical properties were evaluated using compressive tests. For comparison, porous Ni samples with a macro-porous structure prepared by both powder metallurgy
(pore size 800 μm) and the traditional chemical vapour deposition (CVD) method (pore size 1300 μm) were also presented. Results indicated that the porous Ni samples with a micro-porous structure exhibited different deformation behaviour and dramatically increased mechanical properties,
compared to those of the macro-porous Ni samples.

Mechanical properties of micro-porous metals produced by space-holding sintering

Micro-porous nickel foams with an open cell structure were fabricated by the space-holding sintering. The average pore size of the micro-porous nickel specimens ranged from 30 μm to 150 μm, and the porosity ranged from 60 % to 80 %. The porous characteristics of the nickel specimens were observed using scanning electron microscopy (SEM). The mechanical properties were studied using compressive tests. For comparison, macro-porous nickel foams prepared by the chemical vapour deposition method with pore sizes of 800 μm and 1300 μm and porosity of 95 % were also presented. Results indicated that the ratio value of 6 and higher for the specimen length to cell size (L/d) is satisfying for obtaining stable compressive properties. The micro-porous nickel specimens exhibited different deformation behaviour and dramatically increased mechanical properties, compared to those of the macro-porous nickel specimens.

Finite element simulation of deformation processes of micro-components

The aim of this paper is to improve the understanding of deformation of micro medical needle and thread during assembly and then to develop an economical and flexible deformation method. Therefore, the swaging process is computationally simulated with the finite element method in this paper. A commercially available explicit nonlinear finite element analysis code, LS-Dyna, is used to model the 3-D deformation and contact problem. As the firmness of the assembly on the needle depends on the contact force and friction, the contact and the slide between the needle and thread are taken into account in the simulation. The general surface-to-surface contact algorithm (STS) is used to simulate the contact. The paper provides an insight into the deformation of the micro products.

How did we do anything without it?: Indigenous art and craft micro-enterprise use and perception of new media technology

The degree of new media technologies that are broadly available has changed considerably ill nearly two decades since they emerged. How do Indigenous art and craft micro-enterprises use these technologies today? What are their perceptions of it? There is a lack of current data about use of computer technology by Indigenous-owned art and craft enterprises. A current snapshot is needed of the use and consequences of new media technologies in these organisations. This paper reports on results from a 2006 survey of small Indigenous-owned arts enterprises across Australia, including for-profit and non-profit enterprises, those from metropolitan, regional and remote areas, and including both art centres and other types of arts enterprises. The data suggest a major change over the previous decade in the degree that small Indigenous art and craft organisations use and perceive new media technology.

Development of an automated DNA purification module using a micro-fabricated pillar chip

We present a fully automated DNA purification module comprised of a micro-fabricated chip and sequential injection analysis system that is designed for use within autonomous instruments that continuously monitor the environment for the presence of biological threat agents. The chip has an elliptical flow channel containing a bed (3.5 × 3.5 mm) of silica-coated pillars with height, width and center-to-center spacing of 200, 15, and 30 µm, respectively, which provides a relatively large surface area (ca. 3 cm²) for DNA capture in the presence of chaotropic agents. We have characterized the effect of various fluidic parameters on extraction performance, including sample input volume, capture flow rate, and elution volume. The flow-through design made the pillar chip completely reusable; carryover was eliminated by flushing lines with sodium hypochlorite and deionized water between assays. A mass balance was conducted to determine the fate of input DNA not recovered in the eluent. The device was capable of purifying and recovering Bacillus anthracis genomic DNA (input masses from 0.32 to 320 pg) from spiked environmental aerosol samples, for subsequent analysis using polymerase chain reaction-based assays.

The politics of NGOs : empowering marginal groups in a climate of micro-management and distrust

The role of peak NGOs in Australian civil society is considered crucial for representing marginal groups in the public and policy arena. The Howard government had particularly challenged the advocacy, coordination, information, research and policy role of peak NGOs. Instead of dealing with NGOs, the Howard government developed a 'governing through communities' process establishing new arrangements between the Federal government and local communities. It is of concern that 'governance through communities' may directly erode the values of voluntary association, broad representation of diverse groups in society and may negate non-instrumental political relations that NGOs aim to contribute to a healthy democracy. How the new Rudd government relates to peak NGOs is thus worthy of close analysis to understand what democratic role especially peak NGO's will play in Australian civil society.

Tensile deformation of a ultrafine-grained aluminium alloy: micro shear banding and grain boundary sliding

This work investigates the relationship between the strain rate and the ductility and the underlying deformation mechanisms in an ultrafine-grained Al6082 alloy. At room temperature the uniform elongation of the material exhibits a marked increase with decreasing strain rate. This effect is related to the activation of micro shear banding, which is controlled by grain boundary sliding. The contribution of these mechanisms to uniform elongation is estimated. It is proposed that the grain boundary sliding suppresses the transformation of micro shear bands into macro shear bands. The activity of other deformation mechanisms during plastic deformation of the ultrafine-grained material is also discussed.

Micro- and nano-characterization of membrane materials

The global warming has led to enormous challenges worldwide for a large variety of communities, particularly these associated to water and water treatment industry. Due to increasing scarcity of water resources, the development of new membrane materials and water treatment processes will play an important role in tackling this emerging problem. In this paper, the recent development in characterization of in particular, geometrical parameters of micro- and nano-membrane materials will be reviewed. Membranes with micro- and nano-pores have widely been used for ultrafiltration and nanofiltration. The structure of the pores and the surface of the pores/membranes may be optimized to achieve much improved flow rate in these micro-/nano-channels. Therefore, accurate characterization of porous structures will contribute significantly to the prediction of membrane performance. It will not only provide an insight into the new characterization methods but also the development of novel materials.