Assessing the occupational risk of dust particles in the Kenyan tanning industry using rapid image processing and microscopy techniques

The purpose of this study was to investigate the occupational hazards within the tanning industry caused by contaminated dust. A qualitative assessment of the risk of human exposure to dust was made throughout a commercial Kenyan tannery. Using this information, high-risk points in the processing line were identified and dust sampling regimes developed. An optical set-up using microscopy and digital imaging techniques was used to determine dust particle numbers and size distributions. The results showed that chemical handling was the most hazardous (12 mg m(-3)). A Monte Carlo method was used to estimate the concentration of the dust in the air throughout the tannery during an 8 h working day. This showed that the high-risk area of the tannery was associated with mean concentrations of dust greater than the UK Statutory Instrument 2002 No. 2677. stipulated limits (exceeding 10 mg m(-3) (Inhalable dust limits) and 4 mg m(-3) (Respirable dust limits). This therefore has implications in terms of provision of personal protective equipment (PPE) to the tannery workers for the mitigation of occupational risk.

Determining the regional potential for a grass biomethane industry

Grass biogas/biomethane has been put forward as a renewable energy solution and it has been shown to perform well in terms of energy balance, greenhouse gas emissions and policy constraints. Biofuel and energy crop solutions are country-specific and grass biomethane has strong potential in countries with temperate climates and a high proportion of grassland, such as Ireland. For a grass biomethane industry to develop in a country, suitable regions (i.e. those with the highest potential) must be identified. In this paper, factors specifically related to the assessment of the potential of a grass biogas/biomethane industry are identified and analysed. The potential for grass biogas and grass biomethane is determined on a county-by-county basis using multi-criteria decision analysis. Values are assigned to each county and ratings and weightings applied to determine the overall county potential. The potential for grass biomethane with co-digestion of slaughter waste (belly grass) is also determined. The county with the highest potential (Limerick) is analysed in detail and is shown to have ready potential for production of gaseous biofuel to meet either 50% of the vehicle fleet or 130% of the domestic natural gas demand, through 25 facilities at a scale of ca. 30ktyr of feedstock. The assessment factors developed in this paper can be used in other resource studies into grass biomethane or other energy crops. © 2010 Elsevier Ltd.

Irresponsible Lending?: A Case Study of a U.K. Credit Industry Reform Initiative

There are major concerns about the level of personal borrowing, particularly sourced from credit cards. This paper charts the progress of an initiative to create a Responsible Lending Index (RLI) for the credit industry. The RLI proposed to voluntarily benchmark lending standards and promote best practice within the credit industry by involving suppliers of credit, customer representatives and regulators. However, despite initial support from some banks, consumer bodies and the Chair of the Treasury Select Committee, it failed to gain sufficient support from financial institutions in its original format. The primary reasons for this were related to the complexity of building such a robust index and the banks trade body’s fear of exposing its members to public scrutiny. A revised alternative, the Responsible Lending Initiative, was proposed which took into account these concerns. However, the Association of Payment Clearing Service (APACS), the trade body of the credit industry, then effectively destroyed the proposal. This article describes an attempt to address the challenges in the credit card industry with the initiation of the RLI, reflected in stakeholder discourse and in the context of a wider concern expressed by the involved stakeholders in terms of the need for greater responsibility in the banking industry’s lending practices.

Efficacy of Biocides Used in the Modern Food Industry To Control Salmonella enterica, and Links between Biocide Tolerance and Resistance to Clinically Relevant Antimicrobial Compounds

Biocides play an essential role in limiting the spread of infectious disease. The food industry is dependent on these agents, and their increasing use is a matter for concern. Specifically, the emergence of bacteria demonstrating increased tolerance to biocides, coupled with the potential for the development of a phenotype of cross-resistance to clinically important antimicrobial compounds, needs to be assessed. In this study, we investigated the tolerance of a collection of susceptible and multidrug-resistant (MDR) Salmonella enterica strains to a panel of seven commercially available food-grade biocide formulations. We explored their abilities to adapt to these formulations and their active biocidal agents, i.e., triclosan, chlorhexidine, hydrogen peroxide, and benzalkonium chloride, after sequential rounds of in vitro selection. Finally, cross-tolerance of different categories of biocidal formulations, their active agents, and the potential for coselection of resistance to clinically important antibiotics were investigated. Six of seven food-grade biocide formulations were bactericidal at their recommended working concentrations. All showed a reduced activity against both surface-dried and biofilm cultures. A stable phenotype of tolerance to biocide formulations could not be selected. Upon exposure of Salmonella strains to an active biocidal compound, a high-level of tolerance was selected for a number of Salmonella serotypes. No cross-tolerance to the different biocidal agents or food-grade biocide formulations was observed. Most tolerant isolates displayed changes in their patterns of susceptibility to antimicrobial compounds. Food industry biocides are effective against planktonic Salmonella. When exposed to sublethal concentrations of individual active biocidal agents, tolerant isolates may emerge. This emergence was associated with changes in antimicrobial susceptibilities.

Corporate Social Responsibility within the Northern Ireland Construction Industry: A Regional Review

As the construction industry continues to struggle with a poor societal image, many organizations have adopted a positive corporate social responsibility (CSR) towards their surrounding environment, with the objective of improving their persona within social circles. The aim of this research is to identify and document the various approaches adopted by UK contractors in relation to their international counterparts to aid in the identification of possible future benefits which may be exploitable.
In order to acquire the relevant information, a number of qualitative methodologies are adopted including a review of the current literature on the topic along with a detailed semi-structured interview with a UK based industry professional that specializes in corporate social responsibility. Through assessing the findings using qualitative analysis software, it is possible to disseminate the information, resulting in the identification of key findings. This research concludes that a number of factors profoundly affect corporate social responsibility within the UK versus other regions. These factors are identified as the effect of the recession, implementation and reporting along with competitiveness within the sector.
The impaction for practice within the UK construction sector of this research is that it enables various industry leaders to actively consider the findings of the research while also vigorously encouraging the establishment and development of corporate social responsibility, not only within their respective organizations, but within the construction industry as a whole. This would not only result in a more environmentally sustainable industry, but would also raise the awareness of the sector locally, nationally and internationally, therefore improving the overall perception of the sector on a variety of levels. This will ultimately lead to a more sustainable, environmentally friendly and collective industry while also considering the needs of one of its most important external stakeholders – the local community.

Meeting the Requirements of the CDM Regulations: Identification of Critical Success Factors of Small to Medium Sized Contractor’ Compliance in the UK Construction Industry

The Construction Design and Management (CDM) Regulations (2007) is one of the most important set of health and safety regulations in the construction industry today. The aim of this research is to examine critical success factors for CDM compliance in small to medium size contractors in the UK construction industry. The objectives of the research include the identification of critical barriers in doing so along with the identification of success factors where CDM is incorporated. A mixed method approach is adopted in the identification and categorisation of the various factors encompassing a literature review, interviews and questionnaire survey. The key finding which emerge is the lack of knowledge and understanding with regards the CDM regulations with the recommendation to encourage small and medium contractor compliance through illustrating the benefits attainable. The practicality of the research is evident based on the significant uptake in the CDM by larger contractors, yet the research indicates that further insight and guidance is required to educate and inform those working within small to medium sized contractors in the UK. Where such acknowledgement and compliance is adopted, it is envisaged that this sector will benefit from reduced incidents and accidents, increased productivity while ultimately leading to a safer and more productive industry as a whole.

A Review of Meditation in the Irish Construction Industry: Critical Success Factors in Competencies and Processes

The construction industry notoriously excels at dispute creation – both in Ireland and world wide. This paper exams mediation in the Irish construction industry based around critical success factors in the competencies and processes required by mediators operating in the construction industry. Through conducting the relevant analysis, it was possible to extract and outline the resulting critical success factors in process and competencies of mediators in the Irish construction industry. This was achieved through a review of the literature, followed by detailed interviews from industry experts to elicit and highlight the core competencies required. To aid in the study, qualitative analysis using mind mapping software was adopted, thus assisting the identification of the key factors. Following analysis, facilitative mediation was identified as best suited for the industry in question; recommendations and experience were key for mediator selection and five and six factors were identified for mediator skills and mediation critical success factors respectively. The results returned are similar to those determined by authors in other countries and provide a good reference point for the development the industry. By following the findings of this report mediators and parties in dispute can improve processes and be more successful in outcomes. In this study the author shows that mediation is an effective and appropriate method of resolving disputes within the Irish construction industry.

NEC Contracting: Evaluation of the Inclusion of Dispute Review Boards in lieu of Adjudication in the Construction Industry in the United Kinddom

The construction industry is renowned for spending vast sums in the resolution of disputes, but never in the prevention. The purpose of this paper is to analyse the New Engineering Contract (NEC) to determine whether or not adjudication has become misaligned with the contract’s objective of promoting effective management. In doing so, the paper examines dispute review boards in order to ascertain if they could be a viable alternative to adjudication. A sequential mixed methodology is adopted including a detailed literature review, eight semi-structured interviews, culminating in the circulation and analysis of a questionnaire, to record the significance of the factors identified. The research concludes that the majority of individuals agree that dispute review boards would be more aligned with the NEC. The familiarity of members, the potential to curb rogue behaviour of parties and the proactive nature of the board are flagged as positive features, however the cost aspect requires further investigation. The reservations made in the study about adjudication, such as the priority given to speed over accuracy and also the adversarial nature of the process, suggest that a preventative step prior to proceeding to adjudication would coincide more with the three core themes of the NEC Contract and therefore, be a positive addition.

Early Implementation of Building Information Modeling into a Cold-Formed Steel Company: Providing Novel Project Management Techniques and Solutions to Industry

The ability of building information modeling (BIM) to positively impact projects in the AEC through greater collaboration and integration is widely acknowledged. This paper aims to examine the development of BIM and how it can contribute to the cold-formed steel (CFS) building industry. This is achieved through the adoption of a qualitative methodology encompassing a literature review, exploratory interviews with industry experts, culminating in the development of e-learning material for the sector. In doing so, the research team have collaborated with one of the United Kingdom’s largest cold-formed steel designer/fabricators. By demonstrating the capabilities of BIM software and providing technical and informative videos in its creation, this project has found two key outcomes. Firstly, to provide invaluable assistance in the transition from traditional processes to a fully collaborative 3D BIM as required by the UK Government under the “Government Construction Strategy” by 2016 in all public sector projects. Secondly, to demonstrate BIM’s potential not only within CFS companies, but also within the AEC sector as a whole. As the flexibility, adaptability and interoperability of BIM software is alluded to, the results indicate that the introduction and development of BIM and the underlying ethos suggests that it is a key tool in the development of the industry as a whole.