Eddy-current losses in rotor surface mounted permanent magnets

The aim of the work is to study the existing analytical calculation procedures found in literature to calculate the eddy-current losses in surface mounted permanent magnets within PMSM application. The most promising algorithms are implemented with MATLAB software under the dimensional data of LUT prototype machine. In addition finite elements analyze, utilized with help of Flux 2D software from Cedrat Ltd, is applied to calculate the eddy-current losses in permanent magnets. The results obtained from analytical methods are compared with numerical results.

Reflexões sobre a contribuição da Carnot à primeira lei da termodinâmica

The classical interpretations of Nicolas Léonard Sadi Carnot on some physical principles involved in the operation of heat engines were fundamental to the development and formulation of the Second Law of Thermodynamics. Moreover, an accurate historical survey clearly reveals that Carnot was, by that time, also well aware about some new concepts, which were further worked out by other scientists to lead to what was, some time later, known as the mechanical equivalent of heat and the conservation of energy. Benoit Paul Émile Clapeyron recognized these original concepts in the first of Carnot´s monographs, published in 1824, but no explicit citation is found in any post-Carnot classical texts dealing with the First Law of Thermodynamics, including those by Julius Robert Mayer, James Prescott Joule and Hermann Ludwig Ferdinand von Helmholtz. The main objective of the present work is to point out some historical evidences of the pioneering contribution of Carnot to the modern concept of the First Law of Thermodynamics.

Alternative Techniques of Neural Signal Processing in Neuroengineering

Neural signal processing is a discipline within neuroengineering. This interdisciplinary approach combines principles from machine learning, signal processing theory, and computational neuroscience applied to problems in basic and clinical neuroscience. The ultimate goal of neuroengineering is a technological revolution, where machines would interact in real time with the brain. Machines and brains could interface, enabling normal function in cases of injury or disease, brain monitoring, and/or medical rehabilitation of brain disorders. Much current research in neuroengineering is focused on understanding the coding and processing of information in the sensory and motor systems, quantifying how this processing is altered in the pathological state, and how it can be manipulated through interactions with artificial devices including brain–computer interfaces and neuroprosthetics.

Entrenamiento de la fuerza orientado a la mejora de la velocidad de golpeo en tenis

El golpeo de la bola a velocidades elevadas, es un factor determinante para el rendimiento en el tenis moderno. Durante los últimos 20 años se ha producido una gran evolución del juego y los cambios en el juego moderno se han traducido en el uso de poderosos servicios y golpes de fondo. Aunque la fuerza es una capacidad determinante desde la perspectiva de la condición física, ha habido poca investigación para fundamentar la eficacia de los programas de entrenamiento de fuerza para los jugadores de tenis. El objetivo de este estudio es realizar una revisión sobre los criterios básicos para dirigir correctamente el entrenamiento de la fuerza orientado a la mejora de la de la velocidad de golpeo de la pelota. Aunque las necesidades de fuerza dinámica máxima (FDM) en los golpeos son bajas, la literatura científica parece apuntar que unos adecuados niveles de FDM ejercen efectos positivos sobre el aumento de velocidad de golpeo en el tenis. La mejora y mantenimiento de esta manifestación de fuerza se busca a expensas de factores neurales. Los entrenamientos de fuerza útil deben utilizar medios que permitan ejecutar el gesto técnico, implicar las mismas cadenas musculares, rango de movimiento o velocidades de ejecución. En este sentido, se han propuesto la utilización de pelotas medicinales, mancuernas de peso ligero, gomas elásticas, máquinas multifuncionales de resistencia neumática o poleas.

Interfaces e organização da pesquisa no Brasil: da Química à Nanotecnologia

Nanotechnology can be viewed as a powerful tool, capable of shaping the chemistry of atoms and molecules, converting them into exciting nanosized and nanostructured materials, devices and machines. However, in pursuing this task, an exceptional ability is required to deal with complex inter- and multidisciplinary approaches, as imposed by the nanoscale. A new research organization framework, capable of promoting cooperative interactions in many complementary areas, including the industries, is demanded. In this sense, an interesting example are the nanotechnology networks and millenium institutes recently created in Brazil. The highlights and weakness of such cooperative research networks are discussed, in addition to relevant nanotechnology themes focusing on the special needs and resources from the developing nations.

Position sensorless electrically excited synchronous motor drive for industrial use based on direct flux linkage and torque control

Synchronous machines with an AC converter are used mainly in large drives, for example in ship propulsion drives as well as in rolling mill drives in steel industry. These motors are used because of their high efficiency, high overload capacity and good performance in the field weakening area. Present day drives for electrically excited synchronous motors are equipped with position sensors. Most drives for electrically excited synchronous motors will be equipped with position sensors also in future. This kind of drives with good dynamics are mainly used in metal industry. Drives without a position sensor can be used e.g. in ship propulsion and in large pump and blower drives. Nowadays, these drives are equipped with a position sensor, too. The tendency is to avoid a position sensor if possible, since a sensor reduces the reliability of the drive and increases costs (latter is not very significant for large drives). A new control technique for a synchronous motor drive is a combination of the Direct Flux Linkage Control (DFLC) based on a voltage model and a supervising method (e.g. current model). This combination is called Direct Torque Control method (DTC). In the case of the position sensorless drive, the DTC can be implemented by using other supervising methods that keep the stator flux linkage origin centered. In this thesis, a method for the observation of the drift of the real stator flux linkage in the DTC drive is introduced. It is also shown how this method can be used as a supervising method that keeps the stator flux linkage origin centered in the case of the DTC. In the position sensorless case, a synchronous motor can be started up with the DTC control, when a method for the determination of the initial rotor position presented in this thesis is used. The load characteristics of such a drive are not very good at low rotational speeds. Furthermore, continuous operation at a zero speed and at a low rotational speed is not possible, which is partly due to the problems related to the flux linkage estimate. For operation in a low speed area, a stator current control method based on the DFLC modulator (DMCQ is presented. With the DMCC, it is possible to start up and operate a synchronous motor at a zero speed and at low rotational speeds in general. The DMCC is necessary in situations where high torque (e.g. nominal torque) is required at the starting moment, or if the motor runs several seconds at a zero speed or at a low speed range (up to 2 Hz). The behaviour of the described methods is shown with test results. The test results are presented for the direct flux linkage and torque controlled test drive system with a 14.5 kVA, four pole salient pole synchronous motor with a damper winding and electric excitation. The static accuracy of the drive is verified by measuring the torque in a static load operation, and the dynamics of the drive is proven in load transient tests. The performance of the drive concept presented in this work is sufficient e.g. for ship propulsion and for large pump drives. Furthermore, the developed methods are almost independent of the machine parameters.

Kevyiden rakennemateriaalien soveltamismahdollisuudet metsäkoneissa

Asiakkaiden ympäristötietoisuus, metsäkoneille asetettavat korkeat vaatimukset ja kiristyvä kilpailu pakottavat metsäkoneiden valmistajat etsimään vaihtoehtoisia valmistusmateriaaleja, joita käyttämällä metsäkoneet kevenevät ja sitä kautta niiden ympäristökuormitukset ja käyttökustannukset alenevat ja kapasiteetti kasvaa. Metsäkoneiden rakenteiden keventämisessä alumiini on yksi varteenotettava vaihtoehto teräksen korvaajaksi, sillä alumiinin ominaisuus/paino -suhde on terästä parempi. Alumiinin käyttöä hitsatuissa rakenteissa ovat rajoittaneet sen korkea hinta ja melko huono väsymiskestävyys. Diplomityön tavoitteena on ollut selvittää mahdollisuuksia korvata metsäkoneiden rakenteista löytyviä teräksestä valmistettuja osia alumiinista valmistetuilla osilla. Diplomityön teoriaosassa on käsitelty rakenteiden keventämistä, metsäkoneille asetettavia vaatimuksia, alumiinien materiaaliominaisuuksia, alumiinirakenteiden valmistuksessa käytettäviä menetelmiä sekä alumiinirakenteiden suunnittelua. Lisäksi teoriaosassa on käsitelty komposiittien materiaaliominaisuuksia ja komposiittirakenteiden suunnittelua. Diplomityön kokeellisessa osassa on vertailtu nykyisiä rakennemateriaaleja ja alumiineja metsäkoneen eri osien rakennemateriaaleina osien vaatimusprofiileihin ja materiaalien ominaisuusprofiileihin perustuen. Vaatimusprofiilien perusteella on laadittu ominaisuusprofiilit alumiineille ja teräksille. Sovittamalla vaatimus- ja ominaisuusprofiilit yhteen arvoanalyysin avulla, metsäkoneista on etsitty mahdollisia kohteita, joissa nykyinen rakennemateriaali voitaisiin korvata alumiinilla. Tältä pohjalta metsäkoneista löytyi rakenteita, joissa alumiinin käyttö rakennemateriaalina teräksen sijaan olisi mahdollista. Diplomityö toimii hyvänä pohjana tutkittaessa mahdollisuuksia metsäkoneiden rakenteiden keventämiseksi.

Espacio público: universidad, censura y política. Un ensayo visual

Lisbon, October 27, 2014, Dr. Jose Luis Cardoso director of the Institute of Social Sciences (ICS) at the University of Lisbon, has suspended the publication of the number 212 of the prestigious journal Análise Social. The reason: the number contains a visual essay produced by Ricardo Campos that is qualified to use a 'strong language'. While the online edition of the magazine was available (not try to find it at the site of the ICS) the printed edition was in printing machines. Now, the hard copies will be destroyed.

Valmistuskustannusten arviointi ja kustannustiedon käyttö valmistusystävällisyyteen tähtäävässä tuotekehityksessä

Työn tarkoituksena oli tutkia menetelmiä koneiden valmistuskustannusten arvioimiseksi ja hyödyntää kustannustietoa tuotekehitysprosessissa. Taloudellisen suunnittelun menetelmäksi valittiin DFMA -menetelmä. DFMA -menetelmä on suunnittelustrategia, jonka tarkoituksena on ottaa huomioon suunniteltavan tuotteen valmistuskustannukset ja valmistettavuus mahdollisimman aikaisessa tuotekehitysprosessin vaiheessa. Työn soveltavassa osassa käsiteltiin Rauten uutta puristinlinjaa, jolle arvioitiin valmistuskustannukset. Jatkokehitys kohdennettiin kustannusten painopistealueisiin kokoonpanossa ja valituille kokoonpanoille tehtiin muutoksia valmistuskustannusten pienentämiseksi. Kehitetyille kokoonpanoille arvioitiin uudet valmistuskustannukset ja puristimen mekaanisissa osissa saatiin valmistuskustannuksia pienennetyksi n. 22,6 %, joka oli n. 8,5 % koko puristinlinjan yhteenlasketuista kokonaiskustannuksista. Valmistuskustannusten arvioiminen koneen jokaista komponenttia kohden todettiin olevan liian työlästä. Arviointityön helpottamiseksi alettiin kehittää kustannusten arviointijärjestelmää, jonka avulla koneen muuttuvat materiaali- ja osto-osista aiheutuvat kustannukset saataisiin arvioiduksi. Materiaali ja osto-osien kustannukset aiheuttavat yleensä suurimman osan koko koneen valmistuskustannuksista, joten muista valmistusvaiheista kuten kokoonpanosta, koneistuksesta jne. aiheutuvat kustannukset voidaan arvioida karkeammin.

Hybrid LC Filter for Power Electronic Drives: Theory and Implementation

Power electronic converter drives use, for the sake of high efficiency, pulse-width modulation that results in sequences of high-voltage high-frequency steep-edged pulses. Such a signal contains a set of high harmonics not required for control purposes. Harmonics cause reflections in the cable between the motor and the inverter leading to faster winding insulation ageing. Bearing failures and problems with electromagnetic compatibility may also result. Electrical du/dt filters provide an effective solution to problems caused by pulse-width modulation, thereby increasing the performance and service life of the electrical machines. It is shown that RLC filters effectively decrease the reflection phenomena in the cable. Improved (simple, but effective) solutions are found for both differential- and common-mode signals; these solutions use a galvanic connection between the RLC filter star point and the converter DC link. Foil chokes and film capacitors are among the most widely used components in high-power applications. In actual applications they can be placed in different parts of the cabinet. This fact complicates the arrangement of the cabinet and decreases the reliability of the system. In addition, the inductances of connection wires may prevent filtration at high frequencies. This thesis introduces a new hybrid LC filter that uses a natural capacitance between the turns of the foil choke based on integration of an auxiliary layer into it. The main idea of the hybrid LC filter results from the fact that both the foil choke and the film capacitors have the same roll structure. Moreover, the capacitance between the turns (“intra capacitance”) of the foil inductors is the reason for the deterioration of their properties at high frequencies. It is shown that the proposed filter has a natural cancellation of the intra capacitance. A hybrid LC filter may contain two or more foil layers isolated from each other and coiled on a core. The core material can be iron or even air as in the filter considered in this work. One of the foils, called the main foil, can be placed between the inverter and the motor cable. Other ones, called auxiliary foils, may be connected in star to create differential-mode noise paths, and then coupled to the DC link midpoint to guarantee a traveling path, especially for the common-mode currents. This way, there is a remarkable capacitance between the main foil and the auxiliary foil. Investigations showed that such a system can be described by a simple equivalent LC filter in a wide range of frequencies. Because of its simple hybrid construction, the proposed LC filter can be a cost-effective and competitive solution for modern power drives. In the thesis, the application field of the proposed filter is considered and determined. The basics of hybrid LC filter design are developed further. High-frequency behaviour of the proposed filter is analysed by simulations. Finally, the thesis presents experimental data proving that the hybrid LC filter can be used for du/dt of PWM pulses and reduction of common-mode currents.

Erikoissähkökoneen tyyppitestaus

Uusien erikoissähkökoneiden testaus perinteisten standardien mukaan on osittain haasteellista. Erikoissähkökoneille, kuten kestomagneettitahtikoneelle ei ole esitetty suoranaisia standardin vaatimia testejä, joten siihen joudutaan soveltamaan olemassa olevia erillismagnetoiduntahtikoneen standardeja. Testien tavoitteena on olla luotettavia sekä vertailukelpoisia. Mittausten on oltava toistettavissa. Mittaustavasta riippuen voidaan saada erilaisia tuloksia, jotka vaikuttavat lopputulokseen. Standardien mukaisessa testauksessa saadaan mittauksista samanlaisia ja samalla saadaan mittausvirheen mahdollisuus pienemmäksi ja tällä tavoin tulokset keskenään vertailukelpoisemmiksi. Tässä työssä tarkastellaan kahta erilaista erikoissähkokonetta, kestomagneettitahtikonetta ja massiiviroottoriepätahtikonetta. Työssä selvitetään standardin IEC 60034 soveltuvuutta tyyppitesteihin, joita kyseiset konetyypit vaativat. Lisäksi työssä vertaillaan standardin IEC 60034 mukaisen hyötysuhteen määrittämistä. Se antaakin useita vaihtoehtoja hyötysuhteen määrittämiselle.

LS-SVM: uma nova ferramenta quimiométrica para regressão multivariada. Comparação de modelos de regressão LS-SVM e PLS na quantificação de adulterantes em leite em pó empregando NIR

Least-squares support vector machines (LS-SVM) were used as an alternative multivariate calibration method for the simultaneous quantification of some common adulterants found in powdered milk samples, using near-infrared spectroscopy. Excellent models were built using LS-SVM for determining R², RMSECV and RMSEP values. LS-SVMs show superior performance for quantifying starch, whey and sucrose in powdered milk samples in relation to PLSR. This study shows that it is possible to determine precisely the amount of one and two common adulterants simultaneously in powdered milk samples using LS-SVM and NIR spectra.

Escacs, un sistema intel·ligent

Des dels inicis dels ordinadors com a màquines programables, l’home ha intentat dotar-los de certa intel•ligència per tal de pensar o raonar el més semblant possible als humans. Un d’aquests intents ha sigut fer que la màquina sigui capaç de pensar de tal manera que estudiï jugades i guanyi partides d’escacs. En l’actualitat amb els actuals sistemes multi tasca, orientat a objectes i accés a memòria i gràcies al potent hardware del que disposem, comptem amb una gran varietat de programes que es dediquen a jugar a escacs. Però no hi ha només programes petits, hi ha fins i tot màquines senceres dedicades a calcular i estudiar jugades per tal de guanyar als millors jugadors del món. L’objectiu del meu treball és dur a terme un estudi i implementació d’un d’aquests programes, per això es divideix en dues parts. La part teòrica o de l’estudi, consta d’un estudi dels sistemes d’intel•ligència artificial que es dediquen a jugar a escacs, estudi i cerca d’una funció d’avaluació vàlida i estudi dels algorismes de cerca. La part pràctica del treball es basa en la implementació d’un sistema intel•ligent capaç de jugar a escacs amb certa lògica. Aquesta implementació es porta a terme amb l’ajuda de les llibreries SDL, utilitzant l’algorisme minimax amb poda alfa-beta i codi c++. Com a conclusió del projecte m’agradaria remarcar que l’estudi realitzat m’ha deixat veure que crear un joc d’escacs no era tan fàcil com jo pensava però m’ha aportat la satisfacció d’aplicar tot el que he après durant la carrera i de descobrir moltes altres coses noves.

Pla de màrqueting per al llançament d'un nou producte en el mercat dels motors elèctrics per a bancs de proves

Ningú no dubte ja del canvi de mentalitat que s’ha produït en els darrers anys en els compradors pel què fa al mercat de l’automòbil. La seguretat i el respecte per el medi ambient, són actualment dos dels factors claus que el consumidor té en compte a l’hora de comprar un vehicle. D’altra banda en els darrers anys la Unió Europea, ha fixat tota una sèrie normatives per tal de reduir les emissions nocives a l’atmosfera. Així doncs, més seguretat i menys emissions, signifiquen vehicles que incorporin components i sistemas cada cop més sofisticats, els quals, a la vegada, necessiten de bancs d’assaig i equips de test per tal de ser validats. Aquest fet ha provocat una revolució dins dels sistemes de test per a vehicles, per als quals han augmentat enormement les exigències en quan a precisions i repetibilitat per tal d’intentar reproduir, amb la màxima fiabilitat possible, les condicions de treball que hauran de suportar els components durant el seu ús real. Les característiques dels motors elèctrics, resulten ideals per a accionar aquest tipus d’aplicacions, ja que permeten un control del parell molt acurat i una repetibilitat quasi perfecte enfront d’altres sistemas utilitzats fins no fa massa temps. Aquesta demanda creixent d’aquest tipus de màquines elèctriques, obra una nova oportunitat de negoci per a les empreses fabricants de motors elèctrics. L’objectiu principal d’aquest treball és identificar i satisfer les necessitats dels clients, dins d’un mercat industrial concret: el mercat dels motors elèctrics per a bancs de proves de components per a la indústria de l’automoció. La fita és doncs la de proporcionar les eines necessàries per tal de que una empresa, fabricant de motors elèctrics de velocitat variable, pugui realitzar el disseny, desenvolupament i llançament comercial d’un nou tipus de motor, específicament pensat per aquest mercat, amb les màximes garanties d’èxit. Com a principal conclusió, el treball argumenta que el nou producte representa una oportunitat de negoci força atractiva i rendible per a l’empresa, i permetrà diversificar la oferta de la companyia cap a un nou sector fins ara no explotat.

Disseny d'una màquina carregadora de planxa a l'empresa Serralleria i Alumini Vilaró (S.A.V)

Les empreses sempre han buscat com optimitzar el màxim els seus recursos i ser més eficients a la hora de realitzar les tasques que li han estat encomanades. És per aquest motiu que constantment les empreses realitzen estudis i valoracions de com poder millorar dia a dia. Aquest fet no és diferenciador a l’empresa Serralleria i Alumini Vilaró (S.A.V), que dia a dia estudia com optimitzar els seus processos o de vegades introduir-ne de nous per tal d’expandir la seva oferta de serveis. L’empresa és dedica a la fabricació de peces metàl•liques el procés ja sigui només de tall i mecanitzat, plegat, soldadura, acabats en inoxidable, pintura i fins i tot embalatge pel que fa a la part productiva, respecte a la part d’oficina tècnica també ofereix serveis de desenvolupament de productes segons especificacions del client i reenginyeria de qualsevol producte, analitzant la part que és vol millorar. En l’actualitat l’empresa ha detectat una mancança que creu que es podria solucionar, el problema és que l’empresa disposa de varies màquines de tall, entre les quals hi ha una màquina de tall làser i el problema principal és que la càrrega de les planxes del calaix de magatzem a la bancada de la màquina es realitza o bé manualment o a través d’un gripper sostingut al pont grua, depenent del pes de la planxa a transportar. L’objectiu principal d’aquest treball és fer el disseny d’una màquina que permeti automatitzar el procés de transportar la planxa metàl•lica del calaix de magatzem dipositat sobre una taula mòbil a la bancada de la màquina de tall. El disseny que pretenem fer és complet començant per fer un disseny estructural de la màquina més els seus respectius càlculs, moviments que volem aconseguir, tria de components ( motors, sensors ...), elaboració d’un pressupost per poder fer una estimació i finalment la elaboració del programa de control de tota la màquina més la interacció amb la màquina a través d’una pantalla tàctil. Es a dir, el que pretenem és realitzar un projecte que puguem fabricar en la realitat utilitzant tota la informació continguda dins del mateix