Responses of the tropical gorgonian coral Eunicea fusca to ocean acidification conditions

Ocean acidification can have negative repercussions from the organism to ecosystem levels. Octocorals deposit high-magnesium calcite in their skeletons, and according to different models, they could be more susceptible to the depletion of carbonate ions than either calcite or aragonite-depositing organisms. This study investigated the response of the gorgonian coral Eunicea fusca to a range of CO2 concentrations from 285 to 4,568 ppm (pH range 8.1-7.1) over a 4-week period. Gorgonian growth and calcification were measured at each level of CO2 as linear extension rate and percent change in buoyant weight and calcein incorporation in individual sclerites, respectively. There was a significant negative relationship for calcification and CO2 concentration that was well explained by a linear model regression analysis for both buoyant weight and calcein staining. In general, growth and calcification did not stop in any of the concentrations of pCO2; however, some of the octocoral fragments experienced negative calcification at undersaturated levels of calcium carbonate (>4,500 ppm) suggesting possible dissolution effects. These results highlight the susceptibility of the gorgonian coral E. fusca to elevated levels of carbon dioxide but suggest that E. fusca could still survive well in mid-term ocean acidification conditions expected by the end of this century, which provides important information on the effects of ocean acidification on the dynamics of coral reef communities. Gorgonian corals can be expected to diversify and thrive in the Atlantic-Eastern Pacific; as scleractinian corals decline, it is likely to expect a shift in these reef communities from scleractinian coral dominated to octocoral/soft coral dominated under a "business as usual" scenario of CO2 emissions.

Diverging Development Paths of the Electronics Industry in Korea and Taiwan

This paper examines the process and mechanism of economic development in the Republic of Korea and Taiwan through a comparative analysis of the electronics industry in each country. The paper will show that in its initial stage of development, the electronics industry in both economies had the same type of dual structure: a domestic demand sector based on the protected domestic market, and an export sector intended to capitalize on low-wage labor for the international market. However, this dual structure in the two economies faded away after the mid-1970s as their respective indigenous export-oriented enterprises began to develop. But the primary industrial players in each economy were very different. In Korea they were comprehensive electronics manufacturers affiliated with chaebols, and in Taiwan they were small and medium-size enterprises. Differences in the two economies' development mechanisms have brought about this divergence in development paths. In Korea this mechanism has been characterized by the government's positive role and the chaebol's readiness to react to the government's leadership. In Taiwan the development mechanism has been based on the private sector independent from the government. As an extension of such diverged development paths, ICs and personal computers showed spectacular growth in Korea and Taiwan after the 1980s. The development of ICs in Korea was primarily the result of a decisive role played by the chaebol's sizable financial resources, while the competitiveness in personal computers largely reflected the agility and flexibility of Taiwanese small and medium-size enterprises.

Development of Efficient Techniques for the Analysis and Design of Antennas in Dual-Reflectarray Configuration

This thesis contributes to the analysis and design of printed reflectarray antennas. The main part of the work is focused on the analysis of dual offset antennas comprising two reflectarray surfaces, one of them acts as sub-reflector and the second one acts as mainreflector. These configurations introduce additional complexity in several aspects respect to conventional dual offset reflectors, however they present a lot of degrees of freedom that can be used to improve the electrical performance of the antenna. The thesis is organized in four parts: the development of an analysis technique for dualreflectarray antennas, a preliminary validation of such methodology using equivalent reflector systems as reference antennas, a more rigorous validation of the software tool by manufacturing and testing a dual-reflectarray antenna demonstrator and the practical design of dual-reflectarray systems for some applications that show the potential of these kind of configurations to scan the beam and to generate contoured beams. In the first part, a general tool has been implemented to analyze high gain antennas which are constructed of two flat reflectarray structures. The classic reflectarray analysis based on MoM under local periodicity assumption is used for both sub and main reflectarrays, taking into account the incident angle on each reflectarray element. The incident field on the main reflectarray is computed taking into account the field radiated by all the elements on the sub-reflectarray.. Two approaches have been developed, one which employs a simple approximation to reduce the computer run time, and the other which does not, but offers in many cases, improved accuracy. The approximation is based on computing the reflected field on each element on the main reflectarray only once for all the fields radiated by the sub-reflectarray elements, assuming that the response will be the same because the only difference is a small variation on the angle of incidence. This approximation is very accurate when the reflectarray elements on the main reflectarray show a relatively small sensitivity to the angle of incidence. An extension of the analysis technique has been implemented to study dual-reflectarray antennas comprising a main reflectarray printed on a parabolic surface, or in general in a curved surface. In many applications of dual-reflectarray configurations, the reflectarray elements are in the near field of the feed-horn. To consider the near field radiated by the horn, the incident field on each reflectarray element is computed using a spherical mode expansion. In this region, the angles of incidence are moderately wide, and they are considered in the analysis of the reflectarray to better calculate the actual incident field on the sub-reflectarray elements. This technique increases the accuracy for the prediction of co- and cross-polar patterns and antenna gain respect to the case of using ideal feed models. In the second part, as a preliminary validation, the proposed analysis method has been used to design a dual-reflectarray antenna that emulates previous dual-reflector antennas in Ku and W-bands including a reflectarray as subreflector. The results for the dualreflectarray antenna compare very well with those of the parabolic reflector and reflectarray subreflector; radiation patterns, antenna gain and efficiency are practically the same when the main parabolic reflector is substituted by a flat reflectarray. The results show that the gain is only reduced by a few tenths of a dB as a result of the ohmic losses in the reflectarray. The phase adjustment on two surfaces provided by the dual-reflectarray configuration can be used to improve the antenna performance in some applications requiring multiple beams, beam scanning or shaped beams. Third, a very challenging dual-reflectarray antenna demonstrator has been designed, manufactured and tested for a more rigorous validation of the analysis technique presented. The proposed antenna configuration has the feed, the sub-reflectarray and the main-reflectarray in the near field one to each other, so that the conventional far field approximations are not suitable for the analysis of such antenna. This geometry is used as benchmarking for the proposed analysis tool in very stringent conditions. Some aspects of the proposed analysis technique that allow improving the accuracy of the analysis are also discussed. These improvements include a novel method to reduce the inherent cross polarization which is introduced mainly from grounded patch arrays. It has been checked that cross polarization in offset reflectarrays can be significantly reduced by properly adjusting the patch dimensions in the reflectarray in order to produce an overall cancellation of the cross-polarization. The dimensions of the patches are adjusted in order not only to provide the required phase-distribution to shape the beam, but also to exploit the crosses by zero of the cross-polarization components. The last part of the thesis deals with direct applications of the technique described. The technique presented is directly applicable to the design of contoured beam antennas for DBS applications, where the requirements of cross-polarisation are very stringent. The beam shaping is achieved by synthesithing the phase distribution on the main reflectarray while the sub-reflectarray emulates an equivalent hyperbolic subreflector. Dual-reflectarray antennas present also the ability to scan the beam over small angles about boresight. Two possible architectures for a Ku-band antenna are also described based on a dual planar reflectarray configuration that provides electronic beam scanning in a limited angular range. In the first architecture, the beam scanning is achieved by introducing a phase-control in the elements of the sub-reflectarray and the mainreflectarray is passive. A second alternative is also studied, in which the beam scanning is produced using 1-bit control on the main reflectarray, while a passive subreflectarray is designed to provide a large focal distance within a compact configuration. The system aims to develop a solution for bi-directional satellite links for emergency communications. In both proposed architectures, the objective is to provide a compact optics and simplicity to be folded and deployed.

Improvement of Mechanical Properties and Life Extension of High Reliability Structural Components by Laser Shock Processing

Profiting by the increasing availability of laser sources delivering intensities above 109 W/cm2 with pulse energies in the range of several Joules and pulse widths in the range of nanoseconds, laser shock processing (LSP) is being consolidating as an effective technology for the improvement of surface mechanical and corrosion resistance properties of metals and is being developed as a practical process amenable to production engineering. The main acknowledged advantage of the laser shock processing technique consists on its capability of inducing a relatively deep compression residual stresses field into metallic alloy pieces allowing an improved mechanical behaviour, explicitly, the life improvement of the treated specimens against wear, crack growth and stress corrosion cracking. Following a short description of the theoretical/computational and experimental methods developed by the authors for the predictive assessment and experimental implementation of LSP treatments, experimental results on the residual stress profiles and associated surface properties modification successfully reached in typical materials (specifically Al and Ti alloys) under different LSP irradiation conditions are presented. In particular, the analysis of the residual stress profiles obtained under different irradiation parameters and the evaluation of the corresponding induced surface properties as roughness and wear resistance are presented.

Towards description and optimization of abstract machines in an extension of prolog

Competitive abstract machines for Prolog are usually large, intricate, and incorpórate sophisticated optimizations. This makes them difñcult to code, optimize, and, especially, maintain and extend. This is partly due to the fact that efñciency considerations make it necessary to use low-level languages in their implementation. Writing the abstract machine (and ancillary code) in a higher-level language can help harness this inherent complexity. In this paper we show how the semantics of basic components of an efficient virtual machine for Prolog can be described using (a variant of) Prolog which retains much of its semantics. These descriptions are then compiled to C and assembled to build a complete bytecode emulator. Thanks to the high level of the language used and its closeness to Prolog the abstract machine descriptions can be manipulated using standard Prolog compilation and optimization techniques with relative ease. We also show how, by applying program transformations selectively, we obtain abstract machine implementations whose performance can match and even exceed that of highly-tuned, hand-crafted emulators.

Roofscapes and the spatiality of the common

The relationship between forms of delimitation and expropriation of the commons through the management of the "public" have led to a world of enclosures and exact division lines. But this is not how the individual perceives and experiences space, this is how bureaucracy builds it. The body’s individual spatiality is understood as the complex topological extension configured by the sensible world at every turn, reflecting while allowing the crossings, junctions, intensities, densities, proximities, etc., which weave together the experiential fabric wherein he lives. This individual spatiality, when it resonates with others, produces a form of common spatiality, the understanding of which can and should act as a new frame of reference for intervention strategies and spatial politics in the contemporary world. The roofscape, as a space not fitting within the canonical division of public/private, is a unique study case to frame these new concepts.

Simulation of AC, DC, and AC-DC coupled mini-grids. In search of the most efficient system

Renewable energy hybrid systems and mini-grids for electrification of rural areas are known to be reliable and more cost efficient than grid extension or only-diesel based systems. However, there is still some uncertainty in some areas, for example, which is the most efficient way of coupling hybrid systems: AC, DC or AC-DC? With the use of Matlab/Simulink a mini-grid that connects a school, a small hospital and an ecotourism hostel has been modelled. This same mini grid has been coupled in the different possible ways and the system’s efficiency has been studied. In addition, while keeping the consumption constant, the generation sources and the consumption profile have been modified and the effect on the efficiency under each configuration has also been analysed. Finally different weather profiles have been introduced and, again, the effect on the efficiency of each system has been observed.

A fuzzy extension of MAGERIT methodology for risk analysis in information systems

We propose a fuzzy approach to deal with risk analysis for information systems. We extend MAGERIT methodology that valuates the asset dependencies to a fuzzy framework adding fuzzy linguistic terms to valuate the different elements (terminal asset values, asset dependencies as well as the probability of threats and the resulting asset degradation) in risk analysis. Computations are based on the trapezoidal fuzzy numbers associated with these linguistic terms and, finally, the results of these operations are translated into a linguistic term by means of a similarity function.

A study the degree of concentration of the Spanish bunkering

This paper shows the Gini Coefficient of the Spanish bunkering, for the Spanish Port System 1960 to the year 2010 with the aim to describe the Spanish bunkering in these periods and propose future strategies. The stage of bunkering must change due to new regulations of marine fuels but to predict the future you must know the past On December 17 came into force on community standard marine fuels. After a complicated negotiation with the industry moves forward a project that is fully compliant with the guidelines of the International Maritime Organization (IMO) and limiting the sulphur and particulate matter of marine fuels used by ships calling or transit through maritime space of the European Union. The impact of a possible extension at European level of the Sulphur Emission Control Areas (SECA) as they are introduced in the Annex VI of the International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978 (MARPOL) adopted by the International Maritime Organisation (IMO).

In situ analysis of the tensile deformation mechanisms in extruded Mg–1Mn–1Nd (wt%)

An extruded Mg–1Mn–1Nd (wt%) (MN11) alloy was tested in tension in an SEM at temperatures of 323K (50°C), 423 K (150°C), and 523 K (250°C) to analyse the local deformation mechanisms through in situ observations. Electron backscatter diffraction was performed before and after the deformation. It was found that the tensile strength decreased with increasing temperature, and the relative activity of different twinning and slip systems was quantified. At 323K (50C), extension twinning, basal, prismatic (a) and pyramidal (c+a) slip were active. Much less extension twinning was observed at 423K (150ºC) while basal slip and prismatic (a) slip were dominant and presented similar activities. At 523K (250ºC), twinning was not observed, and basal slip controlled the deformation.

An extension of Mohring’s model for land rent distribution

In an early paper Herbert Mohring (J. Poi Et on , 49 (1961)) presented a model for land rent distribution yielding the well-known result that the price of land must fall with the distance from the city center to offset transportation costs. Our paper is an extension of Mohring's model in which we relax some of his drastic simplifying assumptions. This extended model has been incorporated in a method for economic evaluation of city master plans which has been applied to a Swedish city. In this method the interdependence among housing, heating, and transportation, the dura-bility of urban structures, and the uncertainty of future demand are explicitly considered within a cost-benefit approach. Some empirical results from this pilot study concerning land rent distributions are also presented here.

Extension of Euskalduna Conference Centre and Concert Hall: A Contemporary Application of Irregular Reciprocal Frames

Reciprocal frame structures, formed by a set of self-supported elements in a closed circuit, have long been used since antiquity to cover large spans with small elements. The roof structure of the Euskalduna conference centre and concert hall extension in Bilbao, covering an irregu- lar geometry of 3000 m2 with a maximum span of 45 m, presented an interesting opportunity to revisit the concept and to apply these classical systems. Furthermore, its analysis and develop- ment led to an interesting discussion on reciprocal frames. They showed great sensitivity of these systems to the local modification of a particular element, establishment of irregular load paths, mobilisation of almost the entire sys- tem when locally applying a punctual load and, finally, its large deformability. Besides, reciprocal frames present particular construction complexities and possibilities due to the moderate length of the structural elements, the predominance of shear-only connec- tions and the necessity of the entire system to be completely erected to guarantee its stability. Euskalduna extension, completed in 2012, is one of the largest and a very par- ticular case of irregular reciprocal frame structures built in the world. It shows the formal possibilities and potentiality of reciprocal frames to respond to free and irregular geometries.

Linked Data Rights 2.0: extension of ODRL for Licensing Linked Data

Linked Data assets (RDF triples, graphs, datasets, mappings...) can be object of protection by the intellectual property law, the database law or its access or publication be restricted by other legal reasons (personal data pro- tection, security reasons, etc.). Publishing a rights expression along with the digital asset, allows the rightsholder waiving some or all of the IP and database rights (leaving the work in the public domain), permitting some operations if certain conditions are satisfied (like giving attribution to the author) or simply reminding the audience that some rights are reserved.

Viability of the biochar production from different manure wastes in the Amblés Valley (Ávila, Spain)

In the last years, intensive animal husbandry production has led to a large concentration of animals in small areas. This has resulted in the production of excessive amounts of manures with insufficient nearby land for application. One of this areas is the Amblés Valley located in the centre of Spain, near to Ávila city, with an extension of 167472 ha of which 88.9% is agricultural land. This valley has an important livestock focused on pig, cattle, chicken production which is associated with the generation of more than 200,000 t/year of manure. There are a number of environmental problems associated with these intensive agricultural systems, including N and P pollution of water bodies, methane emissions and odour pollution. These serious environmental threats are called for innovative environmental management approaches. A feasible technology for the management of manures, offering a potential to valorise these wastes, is pyrolysis, which results in the production of biochar. The objective of this work is evaluated the technical and economic feasibility of the production of biochar in Amblés Valley (Spain).