Structural behaviour and design of cold-formed steel wall systems under fire conditions

In recent times, light gauge steel framed (LSF) structures, such as cold-formed steel wall systems, are increasingly used, but without a full understanding of their fire performance. Traditionally the fire resistance rating of these load-bearing LSF wall systems is based on approximate prescriptive methods developed based on limited fire tests. Very often they are limited to standard wall configurations used by the industry. Increased fire rating is provided simply by adding more plasterboards to these walls. This is not an acceptable situation as it not only inhibits innovation and structural and cost efficiencies but also casts doubt over the fire safety of these wall systems. Hence a detailed fire research study into the performance of LSF wall systems was undertaken using full scale fire tests and extensive numerical studies. A new composite wall panel developed at QUT was also considered in this study, where the insulation was used externally between the plasterboards on both sides of the steel wall frame instead of locating it in the cavity. Three full scale fire tests of LSF wall systems built using the new composite panel system were undertaken at a higher load ratio using a gas furnace designed to deliver heat in accordance with the standard time temperature curve in AS 1530.4 (SA, 2005). Fire tests included the measurements of load-deformation characteristics of LSF walls until failure as well as associated time-temperature measurements across the thickness and along the length of all the specimens. Tests of LSF walls under axial compression load have shown the improvement to their fire performance and fire resistance rating when the new composite panel was used. Hence this research recommends the use of the new composite panel system for cold-formed LSF walls. The numerical study was undertaken using a finite element program ABAQUS. The finite element analyses were conducted under both steady state and transient state conditions using the measured hot and cold flange temperature distributions from the fire tests. The elevated temperature reduction factors for mechanical properties were based on the equations proposed by Dolamune Kankanamge and Mahendran (2011). These finite element models were first validated by comparing their results with experimental test results from this study and Kolarkar (2010). The developed finite element models were able to predict the failure times within 5 minutes. The validated model was then used in a detailed numerical study into the strength of cold-formed thin-walled steel channels used in both the conventional and the new composite panel systems to increase the understanding of their behaviour under nonuniform elevated temperature conditions and to develop fire design rules. The measured time-temperature distributions obtained from the fire tests were used. Since the fire tests showed that the plasterboards provided sufficient lateral restraint until the failure of LSF wall panels, this assumption was also used in the analyses and was further validated by comparison with experimental results. Hence in this study of LSF wall studs, only the flexural buckling about the major axis and local buckling were considered. A new fire design method was proposed using AS/NZS 4600 (SA, 2005), NAS (AISI, 2007) and Eurocode 3 Part 1.3 (ECS, 2006). The importance of considering thermal bowing, magnified thermal bowing and neutral axis shift in the fire design was also investigated. A spread sheet based design tool was developed based on the above design codes to predict the failure load ratio versus time and temperature for varying LSF wall configurations including insulations. Idealised time-temperature profiles were developed based on the measured temperature values of the studs. This was used in a detailed numerical study to fully understand the structural behaviour of LSF wall panels. Appropriate equations were proposed to find the critical temperatures for different composite panels, varying in steel thickness, steel grade and screw spacing for any load ratio. Hence useful and simple design rules were proposed based on the current cold-formed steel structures and fire design standards, and their accuracy and advantages were discussed. The results were also used to validate the fire design rules developed based on AS/NZS 4600 (SA, 2005) and Eurocode Part 1.3 (ECS, 2006). This demonstrated the significant improvements to the design method when compared to the currently used prescriptive design methods for LSF wall systems under fire conditions. In summary, this research has developed comprehensive experimental and numerical thermal and structural performance data for both the conventional and the proposed new load bearing LSF wall systems under standard fire conditions. Finite element models were developed to predict the failure times of LSF walls accurately. Idealized hot flange temperature profiles were developed for non-insulated, cavity and externally insulated load bearing wall systems. Suitable fire design rules and spread sheet based design tools were developed based on the existing standards to predict the ultimate failure load, failure times and failure temperatures of LSF wall studs. Simplified equations were proposed to find the critical temperatures for varying wall panel configurations and load ratios. The results from this research are useful to both structural and fire engineers and researchers. Most importantly, this research has significantly improved the knowledge and understanding of cold-formed LSF loadbearing walls under standard fire conditions.

Numerical models to simulate the thermal performance of LSF wall panels

Fire safety of buildings has been recognised as very important by the building industry and the community at large. Gypsum plasterboards are widely used to protect light gauge steel frame (LSF) walls all over the world. Gypsum contains free and chemically bound water in its crystal structure. Plasterboard also contains gypsum (CaSO4.2H2O) and calcium carbonate (CaCO3). The dehydration of gypsum and the decomposition of calcium carbonate absorb heat, and thus are able to protect LSF walls from fires. Kolarkar and Mahendran (2008) developed an innovative composite wall panel system, where the insulation was sandwiched between two plasterboards to improve the thermal and structural performance of LSF wall panels under fire conditions. In order to understand the performance of gypsum plasterboards and LSF wall panels under standard fire conditions, many experiments were conducted in the Fire Research Laboratory of Queensland University of Technology (Kolarkar, 2010). Fire tests were conducted on single, double and triple layers of Type X gypsum plasterboards and load bearing LSF wall panels under standard fire conditions. However, suitable numerical models have not been developed to investigate the thermal performance of LSF walls using the innovative composite panels under standard fire conditions. Continued reliance on expensive and time consuming fire tests is not acceptable. Therefore this research developed suitable numerical models to investigate the thermal performance of both plasterboard assemblies and load bearing LSF wall panels. SAFIR, a finite element program, was used to investigate the thermal performance of gypsum plasterboard assemblies and LSF wall panels under standard fire conditions. Appropriate values of important thermal properties were proposed for plasterboards and insulations based on laboratory tests, literature review and comparisons of finite element analysis results of small scale plasterboard assemblies from this research and corresponding experimental results from Kolarkar (2010). The important thermal properties (thermal conductivity, specific heat capacity and density) of gypsum plasterboard and insulation materials were proposed as functions of temperature and used in the numerical models of load bearing LSF wall panels. Using these thermal properties, the developed finite element models were able to accurately predict the time temperature profiles of plasterboard assemblies while they predicted them reasonably well for load bearing LSF wall systems despite the many complexities that are present in these LSF wall systems under fires. This thesis presents the details of the finite element models of plasterboard assemblies and load bearing LSF wall panels including those with the composite panels developed by Kolarkar and Mahendran (2008). It examines and compares the thermal performance of composite panels developed based on different insulating materials of varying densities and thicknesses based on 11 small scale tests, and makes suitable recommendations for improved fire performance of stud wall panels protected by these composite panels. It also presents the thermal performance data of LSF wall systems and demonstrates the superior performance of LSF wall systems using the composite panels. Using the developed finite element of models of LSF walls, this thesis has proposed new LSF wall systems with increased fire rating. The developed finite element models are particularly useful in comparing the thermal performance of different wall panel systems without time consuming and expensive fire tests.

A continuum model of the growth of engineered epidermal skin substitutes

We present a porous medium model of the growth and deterioration of the viable sublayers of an epidermal skin substitute. It consists of five species: cells, intracellular and extracellular calcium, tight junctions, and a hypothesised signal chemical emanating from the stratum corneum. The model is solved numerically in Matlab using a finite difference scheme. Steady state calcium distributions are predicted that agree well with the experimental data. Our model also demonstrates epidermal skin substitute deterioration if the calcium diffusion coefficient is reduced compared to reported values in the literature.

Early local functional changes in the human diabetic retina : a global flash multifocal electroretinogram study

Purpose: To investigate early functional changes of local retinal defects in type II diabetic patients using the global flash multifocal electroretinogram (MOFO mfERG). Methods: Thirty-eight diabetic patients and 14 age-matched controls were recruited. Nine of the diabetics were free from diabetic retinopathy (DR), while the remainder had mild to moderate non-proliferative diabetic retinopathy. The MOFO mfERG was performed at high (98%) and low (46%) contrast levels. MfERG responses were grouped into 35 regions for comparison with DR classification at those locations. Z-scores of the regional mfERG responses were compared across different types of DR defects. Results: The mfERG waveform consisted of the direct component (DC) and the induced component (IC). Local reduction in DC and IC amplitudes were found in diabetic patients with and without DR. With increasing severity of retinopathy, there was a further deterioration in amplitude of both components. Under MOFO mfERG paradigm, amplitude was a useful screening parameter. Conclusion: The MOFO mfERG can help in detecting early functional anomalies before the appearance of visible signs, and may assist in monitoring further functional deterioration in diabetic patients.

Educating for change : a case for a pedagogy of desire in design eduation

Despite major inroads in demystifying creativity for the non-design disciplines, there has been very little movement in the design disciplines themselves beyond traditional paradigms. As argued in this paper, this is particularly noticeable in design education where traditional pedagogical approaches persist despite the emergence of new experimental pedagogies and the possibilities and opportunities they offer. In response, this paper describes what is revealed when a ‘pedagogy of desire’ is used as a critical lens to reflect on an experience of developing and implementing a first year interior design program involving first and second year undergraduate interior design and architecture students. Implications drawn from the review are presented and a case made for continuing experimentation and development of a pedagogy of desire for design learning and teaching.

Questioning pedagogies : Hong Kong pre-service teachers' dialogic reflections on a transnational school experience

There are increasing opportunities in many countries for pre-service teachers to engage in a transnational school-based experience as part of study abroad programmes. The transformative potential of such transnational teaching experiences is recorded in research studies, often supported by data from participant surveys. However, there has been a lack of evidence investigating how shifts in professional understanding derive from such experiences. This qualitative study addresses this issue by exploring the perspectives of 16 pre-service teachers of English as a Second language from Hong Kong, who engaged in transnational teaching activities with primary school pupils in Australia, during their study abroad program. Discourse analysis of participants’ dialogues traces how they encountered conflicting Discourses of ‘student-centredness’ in the Australian classroom. Reflecting dialogically on their experiences led participants to negotiate and reframe their understandings of language teaching pedagogy and themselves as language teachers. The findings demonstrate the importance of both peer and lecturer feedback into the process of dialogic reflection and the need for more longitudinal research into the impact of transnational school-based experience in pre-service teacher education.

Homo- and heteronuclear meso,meso-(E)-Ethene-1,2-diyl-Linked Diporphyrins : preparation, X-ray crystal structure, electronic absorption and emission spectra and density functional theory calculations

Homo-and heteronuclear meso,meso-(E)-ethene-1,2-diyl-linked diporphyrins have been prepared by the Suzuki coupling of porphyrinylboronates and iodovinylporphyrins. Combinations comprising 5,10,15-triphenylporphyrin (TriPP) on both ends of the ethene-1,2-diyl bridge M 210 (M 2=H 2/Ni, Ni 2, Ni/Zn, H 4, H 2Zn, Zn 2) and 5,15-bis(3,5-di-tert-butylphenyl)porphyrinato-nickel(II) on one end and H 2, Ni, and ZnTriPP on the other (M 211), enable the first studies of this class of compounds possessing intrinsic polarity. The compounds were characterized by electronic absorption and steady state emission spectra, 1H NMR spectra, and for the Ni 2 bis(TriPP) complex Ni 210, single crystal X-ray structure determination. The crystal structure shows ruffled distortions of the porphyrin rings, typical of Ni II porphyrins, and the (E)-C 2H 2 bridge makes a dihedral angle of 50° with the mean planes of the macrocycles. The result is a stepped parallel arrangement of the porphyrin rings. The dihedral angles in the solid state reflect the interplay of steric and electronic effects of the bridge on interporphyrin communication. The emission spectra in particular, suggest energy transfer across the bridge is fast in conformations in which the bridge is nearly coplanar with the rings. Comparisons of the fluorescence behaviour of H 410 and H 2Ni10 show strong quenching of the free base fluorescence when the complex is excited at the lower energy component of the Soret band, a feature associated in the literature with more planar conformations. TDDFT calculations on the gas-phase optimized geometry of Ni 210 reproduce the features of the experimental electronic absorption spectrum within 0.1 eV. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Practices of interactive courseware at Malaysia primary smart school : usage standing and causes attributing

Malaysian teachers are now using interactive courseware in their teaching practices as part of teaching activity in classroom, to teach some subjects such as languages, mathematics, and science. Towards this, there is some debate going on the effectiveness of interactive courseware used in classroom. This paper reports data from interviews conducted with school principals and teachers from six selected primary Smart Schools across Malaysia.The interview conducted is looked on their current school practices and challenges in the implementation of interactive courseware in the classroom. The interview covers several aspects of their school facilities, the causes attributed and their concerns. However, the findings revealed that these six schools generally need more supports in the physical and technical form, in order to utilize the interactive courseware. Initially, the current support from the Malaysian Ministry of Education in physical form has proved that not very helpful. Thus, the respondents suggested that supports should be both: physical and technical. Therefore, this preliminary findings could be used as a pointer to the Malaysian government and other stakeholders to the improvement of interface design for future interactive courseware.

VAMP3 regulates podosome organisation in macrophages and together with Stx4/SNAP23 mediates adhesion, cell spreading and persistent migration

The ability of cells to adhere, spread and migrate is essential to many physiological processes, particularly in the immune system where cells must traffic to sites of inflammation and injury. By altering the levels of individual components of the VAMP3/Stx4/SNAP23 complex we show here that this SNARE complex regulates efficient macrophage adhesion, spreading and migration on fibronectin. During cell spreading this complex mediates the polarised exocytosis of VAMP3- positive recycling endosome membrane into areas of membrane expansion, where VAMP3's surface partner Q-SNARE complex Stx4/SNAP23 was found to accumulate. Lowering the levels of VAMP3 in spreading cells resulted in a more rounded cell morphology and most cells were found to be devoid of the typical ring-like podosome superstructures seen normally in spreading cells. In migrating cells lowering VAMP3 levels disrupted the polarised localisation of podosome clusters. The reduced trafficking of recycling endosome membrane to sites of cell spreading and the disorganised podosome localisation in migrating macrophages greatly reduced their ability to persistently migrate on fibronectin. Thus, this important SNARE complex facilitates macrophage adhesion, spreading, and persistent macrophage migration on fibronectin through the delivery of VAMP3-positive membrane with its cargo to expand the plasma membrane and to participate in organising adhesive podosome structures.

Models of collective cell behaviour with crowding effects : comparing lattice-based and lattice-free approaches

Individual-based models describing the migration and proliferation of a population of cells frequently restrict the cells to a predefined lattice. An implicit assumption of this type of lattice based model is that a proliferative population will always eventually fill the lattice. Here we develop a new lattice-free individual-based model that incorporates cell-to-cell crowding effects. We also derive approximate mean-field descriptions for the lattice-free model in two special cases motivated by commonly used experimental setups. Lattice-free simulation results are compared to these mean-field descriptions and to a corresponding lattice-based model. Data from a proliferation experiment is used to estimate the parameters for the new model, including the cell proliferation rate, showing that the model fits the data well. An important aspect of the lattice-free model is that the confluent cell density is not predefined, as with lattice-based models, but an emergent model property. As a consequence of the more realistic, irregular configuration of cells in the lattice-free model, the population growth rate is much slower at high cell densities and the population cannot reach the same confluent density as an equivalent lattice-based model.

A new model to analyze metaphyseal bone healing in mice

Background: Despite the increasing clinical problems with metaphyseal fractures, most experimental studies investigate the healing of diaphyseal fractures. Although the mouse would be the preferable species to study the molecular and genetic aspects of metaphyseal fracture healing, a murine model does not exist yet. Using a special locking plate system, we herein introduce a new model, which allows the analysis of metaphyseal bone healing in mice. Methods: In 24 CD-1 mice the distal metaphysis of the femur was osteotomized. After stabilization with the locking plate, bone repair was analyzed radiologically, biomechanically, and histologically after 2 (n = 12) and 5 wk (n = 12). Additionally, the stiffness of the bone-implant construct was tested biomechanically ex vivo. Results: The torsional stiffness of the bone-implant construct was low compared with nonfractured control femora (0.23 ± 0.1 Nmm/°versus 1.78 ± 0.15 Nmm/°, P < 0.05). The cause of failure was a pullout of the distal screw. At 2 wk after stabilization, radiological analysis showed that most bones were partly bridged. At 5 wk, all bones showed radiological union. Accordingly, biomechanical analyses revealed a significantly higher torsional stiffness after 5 wk compared with that after 2 wk. Successful healing was indicated by a torsional stiffness of 90% of the contralateral control femora. Histological analyses showed new woven bone bridging the osteotomy without external callus formation and in absence of any cartilaginous tissue, indicating intramembranous healing. Conclusion: With the model introduced herein we report, for the first time, successful metaphyseal bone repair in mice. The model may be used to obtain deeper insights into the molecular mechanisms of metaphyseal fracture healing. © 2012 Elsevier Inc. All rights reserved.

A new tip area function for instrumented nanoindentation at extremely small contact depths

The accuracy of measurement of mechanical properties of a material using instrumented nanoindentation at extremely small penetration depths heavily relies on the determination of the contact area of the indenter. Our experiments have demonstrated that the conventional area function could lead to a significant error when the contact depth was below 40. nm, due to the singularity in the first derivation of the function in this region and thus, the resultant unreasonable sharp peak on the function curve. In this paper, we proposed a new area function that was used to calculate the contact area for the indentations where the contact depths varied from 10 to 40. nm. The experimental results have shown that the new area function has produced better results than the conventional function. © 2011 Elsevier B.V.

Evaluation of the skills for preventing injury in youth program : impact on health risk behaviors, injury and school connectedness

Injury is the leading cause of death among young people, and involvement in health risk behaviors, such as alcohol use and transport-related risks, is related to increased risk for injury. Effective health promotion programs for adolescents focus on multiple levels, including relationships with peers and parents, student knowledge, behavior and attitudes, and school-level factors such as school connectedness. This study describes the pilot evaluation of a comprehensive, multi-level injury prevention program for 13-14 year old adolescents, targeting change in injury associated with transport and alcohol risks. The program, called Skills for Preventing Injury in Youth (SPIY), incorporates two primary elements: an 8-week, teacher delivered attitude and behavior change curriculum with peer protection and first aid messages; and professional development for program teachers focusing on strategies to increase students’ connectedness to school. Five Australian high schools were recruited for the pilot evaluation research, with three being assigned to receive intervention components and two assigned as curriculum-as-usual controls. In the intervention schools, 118 Year 8 students participated in surveys at baseline, with 105 completing surveys at follow up, six months following the intervention. In the control schools, 196 Year 8 students completed surveys at baseline and 207 at follow up. Survey measures included self-reported injury, risk taking behavior and school connectedness. Results showed that students in the control schools were significantly more likely to report riding bikes without helmets, riding with dangerous drivers, having driven cars on the road, and using alcohol six months after the program, while the intervention group showed no such increase in these behaviors. Additionally, students in the control schools were significantly more likely to report having had pedestrian-related injuries at follow up than they were at the baseline measurement, while intervention school students showed no change. There was also a trend observed in terms of a decrease in bicycle related injuries among intervention school students, compared with a slight increasing trend in bicycle injuries among control students. Overall, scores on the school connectedness scale decreased significantly from baseline to follow up for both intervention and control students, however measurement limitations may have impacted on results relating to students’ connectedness. Overall, the SPIY program has shown promising results in regards to prevention of students’ health risk behavior and injuries. Evidence suggests that the curriculum component was important; however there was limited evidence to suggest that teacher training in school connectedness strategies contributed to these promising results. While school connectedness may be an important factor to target in risk and injury prevention programs, programs may need to incorporate whole-of-school strategies or target a broader range of teachers than were selected for the current research.

Factors influencing speeding in school zones : the role of mindfulness

Background Excessive speed contributes to the incidence and severity of road crashes. The Theory of Planned Behaviour (TPB) has successfully explained variance in speeding intentions and behaviour. However, studies have shown that more than 40% of the variance in outcome measures of speeding remains unexplained, thus, suggesting additional constructs may help to enhance the TPB’s predictive power. Therefore, this study examined mindfulness; a promising construct which has not yet been tested as an additional TPB predictor. Aims The aims of this study were to explore drivers’ beliefs about speeding in school zones using the extended TPB as a framework and to examine the effect that mindfulness had on driver speeding behaviour in school zones. Methods Australian drivers (N = 17) participated in one of four focus group discussions. The overall sample was comprised of five males and twelve females who were aged between 17 to56 years. All participants were recruited via purposive sampling among 1st year psychology students at a large South East Queensland University. The group discussions took approximately one hour and were guided by a structured interview schedule which sought to elicit drivers’ beliefs, thoughts and opinions on speeding in school zones and the factors which motivate such behaviour. Results Overall, thematic analysis revealed some similar issues emerged across the groups. . In particular and perhaps somewhat unsurprisingly, given public concerns regarding the want to ensure the safety of school children, there was much agreement that speeding in school zones was dangerous and unacceptable. Somewhat paradoxically however, some participants also agreed that they had unintentionally or mindlessly sped in school zones. There were several factors that drivers believed influenced their speeding in school zones including their current mood (e.g., if in a bad mood, anxious, or excited they may be more likely to drive without awareness of, and being attentive to, their driving environment) and the extent to which they were familiar with the environment (i.e., more familiar contexts, more likely to drive mindlessly). Thus, although drivers expressed a belief that speeding in school zones was dangerous and acceptable, the extent to which a driver is mindful does influence whether or not a driver may actually engage in speeding in this context. Discussion and conclusions This study highlights the potential role of mindfulness in helping to explain speeding behaviour in school zones. Mindless drivers may speed unintentionally and while unintentional still be endangering the safety and lives of school children. The findings of this research suggest that unintentional speeding, especially in school zones, may be reduced by countermeasures which heighten the extent to which drivers are mindful of approaching and/or driving through a school zone, such as street markings and engineering measures (e.g.,flashing lights and speed bumps).